Emerson LK90, LK91 Owner's Manual

and 5). The neutral and line (hot) wires

in step 5)to make connections(Figures 4

light fixture(Figure 4). Connect the blue

proper polarity at the lampholders.

must be installed as instructed to maintain

listed wire connectors (previously removed

black line(hot)wire of the light fixture.Use

line(hot)wire from the switch cup to the

switch cup to the white neutral wire of the

Connect the white neutral wire from the

WARNING

To avoid possible fire or electrical shock, make certain no bare wire strands are exposed outside wire connectors.

Figure 5

7.Carefully tuck all wires and splices into the switch housing(1).

8.Attach the cover/light fitter(5)(6) to the switch assembly housing(1) using the two screws(2) that were removed in Step 2) (Figure 4.)

WARNING

To avoid fire or electrical shock, be careful not to pinch wires between the switch housing assembly and the cover.

9.Proceed to “Installation of Glass Bowl”

section.

Installation of Glass Bowl

WARNING

To avoid fire hazard, do not exceed wattage indicated on the fixture.

NOTE: Some light kit models provide a hole in the glass bowl for the fan switch chain.

WARNING

Over lamping the light kit will result in the lamps being automatically shut off. Use only 60-watt maximum candelabra lamps. Turn off electricity before replacing the lamps.

1. Install three 60-watt (maximum) candelabra

base bulbs into the fitter sockets.

2. Depending on the model purchased, insert the fan speed control switch chain through the offset hole in the glass bowl or the hole in the bowl cap.

3. Install the light switch chain through the center of the finial nut. Screw the finial nut finger tight onto the fitters threaded nipple.

CAUTION

Be sure that the fan switch chain does not make contact with the light bulbs. If necessary reposition the light fitter to avoid the fan switch chain from touching the light bulbs.

4. Install pendants onto light fixture chain and

fan switch chain.

NOTE: It is advisable to periodically check the tightness of the finial.

5. Installation is complete. Turn on electricity at

main fuse or circuit breaker box.

FAN SWITCH CHAIN

NOTE: YOUR GLASS MAY NOT LOOK THE SAME AS THE ONE IN THIS ILLUSTRATION. HOWEVER, IT INSTALLS IN A SIMILAR MANNER.

(1) GLASS BOWL

PENDANTS (2)

OUTER BOWL CAP (not on all light kits)

Figure 6

LIGHT FITTER

BOWL CAP

THREADED NIPPLE

(3) FINIAL

LIGHT SWITCH CHAIN

For repair parts, phone:

1-800-654-3545

READ AND SAVE THESE INSTRUCTIONS

Ceiling Fan Light Fixture

SUITABLE FOR DAMP LOCATIONS

THREE 60-WATT CANDELABRA BULBS

USE THESE FIXTURES ONLY WITH EMERSON

CF SERIES CEILING F ANS.

NOTE: ANY LIGHT KIT OR FITTER AND GLASS COMBINATION

COVERED BY THIS MANUAL WEIGHS 5.8 LBS. OR LESS.

Ceiling Fan Light Fixture Owner's Manual

What The Warranty Covers:

All products covered by this Owner’s Manual are warranted against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered.

What The Period Of Coverage Is:

All components are covered by this warranty for one year from the date you purchased your light fixture. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.

What Will Emerson Electric Co. Do To Correct Problems: Emerson Electric Co. will replace a defective Emerson Light Fixture at no charge to you. WE WILL SHIP THE REPAIRED PRODUCT OR REPLACEMENT TO YOU AT

NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL, REINSTALLATION AND SHIPPING OF THE PRODUCT TO EMERSON. How Can You Get Service:

YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE LIGHT FIXTURE TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized service center.

• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort Products, Division of Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers shown on the product with your request.

• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service center.

You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center. Your Emerson Light Fixture should be properly packed to avoid damage in transit since we will not be responsible for any such damage.

What Is Not Covered:

This warranty also does not cover any defects, malfunctions or failures caused by:

• Repairs by persons not authorized by Emerson Electric Co.,

• Use of parts or accessories not authorized by Emerson Electric Co.,

• Mishandling, improper installation, modifications or damage to your light fixture while in your possession, or

• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.

Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:

• The original purchaser or user ceases to own the product, or

• The ceiling fan is moved from its original point of installation.

This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral warranties apply, and no employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co. REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but are not limited to such damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing or replacing other property which was damaged if this product does not work properly.

How State Law Relates To The Warranty:

Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

LIMITED WARRANTY

Air Comfort Products

DIVISION OF EMERSON ELECTRIC CO. 8100 W. Florissant ¥ St. Louis, MO 63136

Form No.

BP7438

Part No. F40BP74380000

Printed in China 06/11

Part No. F40BP74380000 Form No. BP7438

ETL Model No.: LK90, LK91, LK140, LK141

and 3). The neutral and line (hot) wires

in step 5)to make connections(Figures 2

light fixture(Figure 2). Connect the blue

swi

8.8.

(3) WI

NNECT

HIT

BLUE

IRE

BLACK

IRE

SWI

AIN

(1) SWI

ASS

BLY

(5) COVER

(2)

CREWS (4) CENTER SCREW

(7)

OWL

(

) LIGHT

(

)

NUT

(8) LOCKWASHE

proper polarity at the lampholders.

must be installed as instructed to maintain

listed wire connectors (previously removed

black line(hot)wire of the light fixture.Use

line(hot)wire from the switch cup to the

switch cup to the white neutral wire of the

Connect the white neutral wire from the

WA RN

et y I

To avoid fire, shock, and serious personal injury, follow all instructions carefully.

carefully

Owner's

1. Read your Manual for future reference.

2. Be careful Befo serv

eing

b locked, securely fasten a warning device, such as a tag, to the service panel. Do not exceed the wattage indicated on fixture.

circuit breaker box before wiring. Make certain no bare wires are exposed outside the wire connectors.

All wiring must conform to national and local electrical codes.

Follow the recommended

fixture. If have described in this manual should be performed by a licensed electrician.

RN I

Emerson CF Emerson CF Series Ceiling Fans installed wet locations.

ss e

insta

tch

swi

ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION

possible

avoid

you

light

our

G: To

Series

m b l y a nd

install

not

s mi

art

Manual

bla

and

he fa

lling

ed on

electrical shock be sure

feel

ixture

duce the

Ceiling Fans in indoor locations. This light kit

use

ssing

serv

lock

acciden

you

the

icing

serv

tall

instructions

not

stall

sk of

al la

light fixture

dama

before

when

ligh

en th

have enough electrical

for the proper method

possible fire and electrical shock,

Call toll-free:

1-800-654-3545

WA RN I NG

hock,

To be ma

avoid

electricity

sure

us e or circ

ssible

lectrica

turned

the

off

t bre aker box

t i o n

the light

installing

cleaning,

ixt

t f

sconnecting

serv

electricity

censed

4. Remove the center screw(6) from the

5. Caref ull y locat e t he whi

6. Ins

ing,

aint

ceiling

ce disconnecting

ectri

mea

turned

of wiring

Any e

wiring knowledge

switch cup (Figure 1).

wires the

(labeled

swi

cup

connectors from the wires.

black

fitter(7) through

light

the

switch cup (Figure 2)

the

in the switch cup

taut

wires

onto

while installing switch

prevent the wires from twisting.

before wiring.

(

(3) S

SWITCH

(1)

(6) CENTER SCR

Figur

REWS

Installat ion on Emerson Fans

w it c h Cu

Modular

Having

1. Remove all parts and parts from the carton.

2. Remove t he switch cup(1) from the cover plate(2) by removing the three screws(3) around the side cup (Figure 1).

3. Disconnect the motor connector(4) from the switch cup connector(5) (Figure 1).

w it h Cent er Screw

packages

of the switch

fixture.

working

switc

reve

mea

off at the

ectrica

not

either

and

the light

Owner's

Retain

ear

power o

pow

cannot

fuse

main

your new light

experience,

work no

onl

stall

used

to be

and blue

"LIGHT")

"L"

remove

whit

e wires f

center

the

and

fitter. Hold

COV

(

)

( CONNECTOR

from

wir

thread

cup

H CUP

n at

hole

t supplied se cup.

washer(8)

loc

cure

the

irmly

ligh

tight kit

and

tter

the

x nu

To b s

e wi

av caref

tch

)

Proceed

12.

section.

oid

ul up

NI N

ibl

ver

“Installation

ectr

res

ate

Glass

etw

Bowl”

through

wires

white

and

black

the

Insert

(4) MOTOR

NNECTO

(3) SCRE

(8) L

(1) SWIT

Figure 2

To avoid

LACK

)

(

BOW

NUT

)

TTER

WA R

ssible fire or electrical

sh ock, ma ke c ertain no bar e wi re

are e xposed outside w ir

nd s

stra connectors.

gure

9. Carefully tuck all wires and splices into the switch cup(1). (Figure 2.)

10. Connect the motor connector(4) to switch cup connector(5).

11. Position the switc assembly(7) on the cov install the three screws(3) that were pr evio usly rem oved in St ep 2 a nd tighten securely.

ER PLAT

(2) CO

(5) SWI

CONNECTOR

(6) WI

NNECT

AN SWITCH

YOUR

MAY

ME AS TH

OWEV

NSTA

NI N G

h cup(1) and fitter

er plate(2) and

LOO

STR , IT IN

ANN

TTE

I K TH

O AT

ER.

al la

t i o n

Ha vi ng T

Em e r s o n F

w o-Pi ec

it c h H ou s i n g s

1. Remove all parts and parts packages from carton.

oid poss

electric or circuit

2. R e m o v e the cover(5) f r o m t h e fan

switch housing(1) by removing the two

ible e

turned

reaker box befo

lectri

off

c s

outer screws(2). (See Figure 4).

R E

Figure

3. Remove the center screw(4) from the cove r(5). Insert the black and white

wires from the light kit fitter(6) thru the

hread

and t

hole

switc h

cover tightly onto the light kit fitter.

4. Insert the black and white wires through the lockwasher(8) an d hex nu t ( 9 )

the

supplied. Firmly tighten the hex nut to secure the light kit fitter to the switch housing cover(5).

th e wh ite and blu e

5. C aref ully loc ate wires (labeled either “L” or “LIGHT”) in the switch housing and remove the wire

connectors(3) from the wires.

Di e-C

hock

main fu

wiring

housi ng