Emerson CF4801GES00, CF4801AP00, CF4801AB00, CF4801BS00, CF4801GBZ00 Owner's Manual

...

0 (0)

Part No. F40BP74470001 Form No. BP7447-1 Revision: 131113 U.L. Model No.: CF4801 and CF4501

READ AND SAVE THESE INSTRUCTIONS

PREMIUM™ SELECT

Ceiling Fan Owner's Manual

Questions, problems, missing parts: Before returning to the store call

Emerson Electric Customer Service

8 a.m. - 6 p.m., Eastern, Monday-Friday

1-800-654-3545

www.emersonfans.com

Net Weight: 23.8 Lbs.

Model Numbers

CROWN™ SELECT

Model Numbers

Fan Blades Not Included

CF4801AB00 CF4801AP00 CF4801BS00 CF4801GBZ00 CF4801GES00 CF4801ORB00 CF4801SW00 CF4801VNB00 CF4801WW00

CF4501AP00 CF4501GBZ00 CF4501GES00 CF4501VNB00

Safety Instructions

TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a. Use this unit only in a manner intended by the

manufacturer. If you have questions, contact the manufacturer.

b. Before servicing or cleaning unit, switch power off

at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel.

WARNING

Additional Safety Instructions for Installation

1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.

2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70-2014” and Local Electrical Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed electrician.

3. The outlet box and joist must be securely mounted and capable of reliably supporting at least 50 pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan Support of 22.7 kg. (50 lbs.) or less”, and use the mounting screws provided with the outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

4. The downrod furnished with the fan provides the minimum recommended floor to fan blade clearance for an 8 foot ceiling.

5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.

6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not know enough about electrical wiring, have your fan installed by a licensed electrician.

WARNING: To reduce the risk of electrical shock, this fan must be installed with an isolating wall control/switch.

NOTE: This fan is suitable for use with solid-state speed controls.

WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not specifically approved for this fan.

WARNING: This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use this product by Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson could result in personal injury or property damage.

WARNING: To reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

NOTE: All setscrews must be checked and re-tightened where necessary before installation.

1. Read your owner’s manual carefully and keep it for future reference.

2. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before servicing.

3. Do not put anything into the fan blades while they are turning.

4. Do not operate reversing switch until fan blades have come to a complete stop.

DATE CODE:

The date code of this fan may be found on the box, stamped in ink on a white label. You should record

this data above and keep it in a safe place for future use.

U.L. Model No.: CF4801 and CF4501

READ AND SAVE THESE INSTRUCTIONS

Table of Contents

Section Page

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

1. Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . .3-4

2. Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . .4

3. Ceiling Fan Assembly . . . . . . . . . . . . . . . . . . . . . . . . . .5-7

4. How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . .8

5. How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .9

6. Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

7. Using Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . .10

Section Page

8. Attaching Optional Light Kit . . . . . . . . . . . . . . . . . . . . . . .11

9. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

10. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

11. Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

12. Crown Select Repair Parts . . . . . . . . . . . . . . . . . . . . . .13

13. Premium Select Repair Parts . . . . . . . . . . . . . . . . .14-15

14. Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Ceiling Fan Limited Warranty . . . . . . . . . . . . . . . . . . . . . . .19

1. Unpacking Instructions

emersonfans.com

Please contact 1-800-654-3545 for further assistance

U.L. Model No.: CF4801 and CF4501

This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co. could result in personal injury or property damage.

WARNING

Do not install or use fan if any part is damaged or missing. Call Toll-Free:

1-800-654-3545

WARNING

1. Check to see that you have received the following parts:

NOTE: If you are uncertain of part description, refer to exploded view illustration.

NOTE: Place the parts from the loose parts bags in a small container to keep them from being lost. If any parts are missing, contact your local retailer or catalog outlet for replacement before proceeding.

2. Remove and discard the two cardboard shipping

retainers securing the motor hub in the motor housing assembly.

3. Remove the fan motor assembly from the protective

plastic bag. Place all carton contents on a protective surface.

PACKAGE CONTENTS

HARDWARE CONTENTS

Part Description Quantity

1 Threaded Studs, #8-32 x 1-1/4” 2 2 Knurled Knobs, #8-32 4 3 Lockwashers, External Tooth #8 2 4 Wire Connectors, 12 ga. 3 5 Threaded Studs, #8-32 x 1” 2 6 Clevis Pin 1 7 Hairpin Clip 1 8 Hex Wrench, 5/32” 1

9 Setscrew 1 10 #8-32 x 3/8” Screws 2 11 Lockwashers 2 12 #10-32 x 18mm Oval Head Screws 11 13 #10-24 x 14mm Pan Head Screws 21 14 Flat Washers 21 15 Pull Chain Pendants & Couplings 2 16 Blade Balance Kit 1

Part Description Quantity

A Fan Motor & Housing Assembly 1 B Ceiling Canopy 1 C Motor Coupler Cover 1 D Blades Flanges 5 E Hanger Bracket 1 F Hanger Ball/Downrod Assembly 1 G Uplight Lead Assembly 1 H 25-Watt Candelabra Bulbs 3

12 13 14

Before assembling your ceiling fan, refer to section on proper method of wiring your fan (page 9). If you feel you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician.

WARNING

This Manual Is Designed to Make it as Easy as Possible for You to Assemble,

Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

One Phillips head screwdriver One stepladder One wire stripper

Materials

Wiring outlet box and box connectors must be of type required by the local code. The minimum wire would be a 3-conductor (2-wire with ground) of following size:

Installed Wire Length Wire Size A.W.G.

Up to 50 ft. 14

50-100 ft. 12

Your Emerson ceiling fan comes supplied with a Fan/Light Remote Control which consists of a receiver mounted inside the ceiling cover of the fan motor housing. This system allows you to regulate your ceiling fan speed and light ON/OFF.

U.L. Model No.: CF4801 and CF4501

2. Electrical Requirements

Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit.

To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked “Acceptable for Fan Support of 22.7 kg. (50 lbs.) or less”, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

WARNING

Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock.

WARNING

To avoid fire or shock, follow all wiring instructions carefully.

Any electrical work not described in these instructions should be done or approved by a licensed electrician.

WARNING

If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture.

1. Unpacking Instructions (Continued)

emersonfans.com

Please contact 1-800-654-3545 for further assistance

U.L. Model No.: CF4801 and CF4501

3. Ceiling Fan Assembly

1. Position the fan motor and housing assembly in the

lower foam packing so that the top of the motor is facing you.

2. Separate, untwist and unkink the four motor leads.

3. Obtain the hanger ball/downrod assembly and

remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod (Figure 1). Remove the pin from the downrod , then remove the hanger ball. Retain the pin and hanger ball for reinstallation in Step 6.

4. Route the white, blue, and black motor leads through

the downrod. Fold the yellow wire into the slot in the motor coupling, slide the downrod down the wires and seat the downrod in the motor coupling (Figure 2).

5. Align the clevis pin holes in the downrod with the

holes in the motor coupling. Install the clevis pin and secure with the hairpin clip (Figure 2). The clevis pin must go through the holes in the motor coupling and the holes in the downrod. Push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to prevent the clevis pin from working loose. Pull on the hanger ball to make sure the clevis pin is properly installed.

Figure 1

Figure 2

It is critical that the clevis pin in the motor coupling is properly installed and the setscrews securely tightened. Failure to verify that the pin and setscrews are properly installed could result in the fan falling.

WARNING

HANGER BALL

SETSCREW

DOWNROD

SETSCREW

CLEVIS PIN

DOWNROD

HAIRPIN CLIP

CLEVIS PIN

DOWNROD

HAIRPIN CLIP

MOTOR COUPLING

YELLOW LEADS

BROWN LEAD RED LEAD

CLEVIS PIN

MOTOR COUPLING

YELLOW LEAD FROM UPLIGHT

U.L. Model No.: CF4801 and CF4501

3. Ceiling Fan Assembly (Continued)

Figure 3

Figure 4

Figure 5

6. Install the setscrew (supplied in loose parts bag) in

the motor coupling and tighten using the 5/32" setscrew wrench (supplied) (Figure 3).

7. Screw two 1” threaded studs (provided) into the

motor (Figure 4). Leave approximately 7/8” of the stud extending above the motor. Slide the motor cover over the downrod and rotate the cover until the threaded studs protrude; install two knurled knobs (supplied) to secure the cover.

NOTE: Make sure the red and brown leads are capped with wire connectors. Make sure the red, brown, and yellow wires and wire connectors are completely inside motor coupling cover and not pinched between the motor coupling cover and motor.

8. Position the ceiling cover over the downrod. Be sure

the cover is oriented correctly, with the large opening at the top (Figure 5).

9. Reinstall the hanger ball on the downrod as

follows. Route the motor leads through the hanger ball and slide the hanger ball over the downrod (Figure 5). Install the pin through the holes at the top of the downrod and slide the hanger ball up the downrod, aligning the ball so the pin is captured in the groove in the top of the hanger ball. Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball. A loose setscrew could create fan wobble.

10.The blue, black and white leads exiting the downrod

are 80-inches long. Before installing fan, measure up approximately 6 to 9-inches above the ball/downrod assembly. Cut off excess leads and strip back insulation 1/2-inch from end of leads.

It is critical that the pin in the hanger ball is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling.

WARNING

RED LEAD

BROWN LEAD

MOTOR

WIRE CONNECTORS

DOWNROD

SETSCREW

KNURLED KNOB

MOTOR COUPLING COVER

WIRE CONNECTOR

YELLOW LEADS

1" THREADED STUD

7/8"

HANGER BALL

CEILING COVER

DOWNROD

SETSCREW

+ 14 hidden pages