Files for CF2000BC02
Size:
224.56 Kb
Download

READ AND SAVE THESE INSTRUCTIONS

Model No.

CF2000AB02

CF2000AW02

CF2000BC02

CF2000ORB02

DATE CODE:

The date code of this fan may be found on the box, stamped in ink on a white label.

You should record this data above and keep it in a safe place for future use.

CF2000PW02

CF2000WB02

CF2000WW02

Max. Weight: 26.0 Lbs.

With Blades

MAUI BAY

Ceiling Fan Owner's Manual

Part No. F40BP73230001

Form No. BP7323-1

 

U.L. Model No.: CF2000

 

 

!WARNING

WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.

Safety Instructions

1.Read your owner’s manual carefully and keep it for future reference.

2.Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel.

3.Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before servicing.

4.Do not put anything into the fan blades while they are turning.

5.Do not operate reversing switch until fan blades have come to a complete stop.

Additional Safety Instructions for Installation

1.To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.

2.All wiring must be in accordance with the National Electrical Codes “ANSI/NFPA 70-1999”and Local Electrical Codes. Use the National Electrical Code if Local Electrical Codes do not exist. The ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed electrician.

3.The outlet box and joist must be securely mounted and capable of reliably supporting at least 50 pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan Support”, and use the mounting screws provided with the outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

4.The downrod furnished with the fan provides the minimum recommended floor to fan blade clearance for an 8 foot ceiling.

5.The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.

6.Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not know enough about electrical wiring, have your fan installed by a licensed electrician.

WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not specifically approved for this fan.

WARNING: This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Electric, Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric, Co could result in personal injury or property damage.

WARNING: To reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

 

TABLE OF CONTENTS

Page

 

 

Rules for Safe Use & Installation

.............................................................................................................................

2

Tools Needed for Assembly .....................................................................................................................................

 

3

Unpacking Instructions.............................................................................................................................................

 

3

Assembly Instructions ..............................................................................................................................................

 

4

Electrical Requirements ...........................................................................................................................................

 

5

How to Hang Your Ceiling Fan.................................................................................................................................

 

5

How to Wire Your Ceiling Fan..................................................................................................................................

 

6

Installing Fan Blades................................................................................................................................................

 

6

Using Your Ceiling Fan ............................................................................................................................................

 

7

Attaching Light Kit ....................................................................................................................................................

 

7

Maintenance.............................................................................................................................................................

 

7

Trouble Shooting......................................................................................................................................................

 

8

Repair Parts ........................................................................................................................................................

 

9-10

Warranty.................................................................................................................................................................

2

11

 

 

This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

One Phillips head screwdriver

One stepladder

Five wire connectors (supplied)

One wire stripper

MATERIALS

Wiring outlet box and box connectors must be of type required by the local code. The minimum wire would be a 3-conductor(2-wirewith ground) of the following size:

Installed Wire Length

Wire Size A.W.G.

Up to 50 ft.

14

50-100ft.

12

!WARNING

Before assembling your ceiling fan, refer to section on proper method of wiring your fan (page 6). If you feel you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician.

Unpacking Instructions

For your convenience, check-offboxes are provided next to each step. As each step is completed, place a check mark in the box. This will insure that all steps have been completed and will be helpful in finding your place should you be interrupted.

!WARNING

Do not install or use fan if any part is damaged or missing. Call Toll-Free:

1-800-654-3545

!WARNING

This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Electric, Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric, Co. could result in personal injury or property damage.

1.Open styrofoam unit containing fan. Remove top half of styrofoam unit. Remove parts and check to see that you have received the following:

a.Fan motor and housing assembly

b.One motor cover

c.One ceiling cover

d.Five blade flanges

e.One hanger ball/downrod assembly

f.One hanger bracket

g.One switch housing cover

h.One loose parts bag containing:

1.One setscrew

2.One setscrew wrench

3.Eleven 10-32x 5/8" oval head screws

4.Two 1” threaded studs

5.Two 1-1/4”threaded studs

6.Four knurled knobs

7.Five wire connectors

8.Two 8-32x 3/8" screws

9.One pull chain pendant and coupling

10.One hairpin clip

11.One clevis pin

12.Four lockwashers

13.Twenty-one10-32x 3/8" pan head screws

14.Twenty-oneflat washers

NOTE: Place the parts from the loose parts bags in small containers to keep them from being lost. If any parts are missing, contact your local retailer or catalog outlet for replacement before proceeding.

NOTE: Fan blades are ordered separately and are packaged in separate carton.

FAN MOTOR AND

HOUSING ASSEMBLY

 

HANGER BALL/

LOOSE

DOWNROD

PARTS

ASSEMBLY

BAG

 

 

HANGER

BLADE

BRACKET

FLANGES

 

 

MOTOR

 

COVER

CEILING

 

COVER

SWITCH

 

 

HOUSING

 

COVER

3

Assembly Instructions

1.Remove the fan motor and housing assembly from styrofoam packaging and position it so that the top of the motor is facing you.

2.Separate, untwist and unkink the three motor leads. Route the motor leads through the hanger ball/downrod assembly and seat the downrod in the motor coupling (Figure 1).

MOTOR LEADS (BLACK, WHITE,

AND BLUE)

HANGER BALL/

DOWNROD ASSEMBLY

MOTOR

COUPLING FAN MOTOR AND

HOUSING ASSEMBLY

Figure 1

!WARNING

It is critical that the clevis pin in the motor coupling is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed (as shown in Figure 2) could result in the fan falling.

3.Align the clevis pin holes in the downrod with the holes in the motor coupling. Install the clevis pin and secure with the hairpin clip (Figure 2). (Pin and clip are supplied in loose parts bag.) The clevis pin must go through the holes in the motor coupling and the holes in the downrod. Push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to prevent the clevis pin from working loose. Pull on the hanger ball to make sure the clevis pin is properly installed.

4.Install the setscrew (supplied) in the motor coupling (Figure 2). While pulling up on the hanger ball, tighten the setscrew using the setscrew wrench (supplied).

NOTE: The setscrew must be properly installed as described above, or fan wobble could result.

5.Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod (Figure 3). Remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for reinstallation in step 8.

PIN

HANGER BALL

DOWNROD

SETSCREW

 

Figure 3

6.Screw two 1” threaded studs (supplied) into the motor (Figure 4). Leave approximately 7/8” of the stud extending above motor. Slide the motor cover over the downrod and rotate the cover until the threaded studs protrude; install two lockwashers and knurled knobs (supplied) to secure the cover.

NOTE: Make sure the connected red leads, the connected brown leads, and the white lead are completely inside the motor cover and not pinched between the motor cover and the motor.

KNURLED KNOB

LOCKWASHER

MOTOR COVER

1" THREADED STU 7/8"

DOWNROD

HANGER BALL

HAIRPIN

CLIP

SETSCREW

MOTOR

COUPLING

CLEVIS PIN

WHITE LEAD

CONNECTED

BROWN LEADS

HAIRPIN

CLEVIS PIN

MOTOR

CLIP

COUPLING

CONNECTED

 

RED LEADS

SETSCREW

 

Figure 4

MOTOR

7.Position the ceiling cover over the downrod. Be sure the cover is oriented correctly, with the large opening at the top (Figure 5).

PIN

HANGER BALL

DOWNROD

Figure 2

Figure 5

4

 

8.Reinstall the hanger ball on the downrod (Figure 5) as follows. Route the motor leads through the hanger ball and slide the hanger ball over the downrod. Install the pin through the holes at the top of the downrod and slide the hanger ball up the downrod, aligning the ball so the pin is captured in the groove in the top of the hanger ball. Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball. A loose setscrew could create fan wobble.

!WARNING

It is critical that the pin in the hanger ball is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling.

9.The fan comes with blue, black and white leads that are 80” long. Before installing fan, measure up approximately 6 to 9-inchesabove the ball/ downrod assembly. Cut off excess leads and strip back insulation1/2-inchfrom end of leads.

Electrical Requirements

Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit.

The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds.

!WARNING

To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked “Acceptable for Fan Support”, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture.

!WARNING

Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with national and local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock.

How to Hang Your

Ceiling Fan

!WARNING

The fan must be hung with at least 7' of clearance from floor to blades (Figure 6).

NOTE: For ease of installation, first the fan motor and housing assembly is installed on the ceiling. Then after wiring of the fan is completed, the fan blade assemblies will be attached to the motor hub. 5

CEILING

AT LEAST 7'

Figure 6

FLOOR

!WARNING

The outlet box and joist must be securely mounted and capable of supporting at least 50 lbs. Use only a U.L. outlet box listed as “Acceptable for Fan Support”.

1.Securely attach the hanger bracket to the outlet box using the two screws supplied with the outlet box. (Figure 7).

!WARNING

Hanger bracket must seat firmly against outlet box. If the outlet box is recessed, remove wall board until bracket contacts box. If bracket and/or outlet box are not securely attached, the fan could wobble or fall.

OUTLET

BOX

TWO SCREWS

 

SUPPLIED WITH

HANGER

OUTLET BOX

 

BRACKET

Figure 7

TAB

Figure 2

 

2.Carefully lift the fan and seat the hanger ball/ downrod assembly on the hanger bracket that was just attached to the outlet box (Figure 8). Be sure the groove in the ball is lined up with tab on the hanger bracket (Figure 7).

!WARNING

Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard.

NOTE: CEILING COVER,

 

SUPPLY WIRES AND

OUTLET

FAN WIRES OMITTED

BOX

FOR CLARITY.

 

 

HANGER

 

BRACKET

Figure 8

HANGER BALL/

Figure 3

DOWNROD ASSEMBLY

 

!WARNING

To avoid possible fire or shock, do not pinch wires between the hanger ball/downrod assembly and the hanger bracket.

How to Wire Your

Ceiling Fan

If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician.

!WARNING

To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation.

1.Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the grounding conductor of supply (this may be a bare wire or wire with green colored insulation) (Figure 9). Securely connect wires with wire connector supplied.

SUPPLY

BLACK AND BLUE

GROUND

FAN WIRES

GROUND

 

WIRE

 

WIRE

 

LISTED

WHITE SUPPLY

WIRE

CONNECTOR (3)

(NEUTRAL)

GREEN WIRE

 

(GROUND) FROM

WHITE FAN

HANGER BRACKET

WIRE

GREEN WIRE

BLACK SUPPLY

(GROUND) FROM

(HOT)

HANGER BALL

 

 

NOTE: CEILING COVER

Figure 4

OMITTED FOR CLARITY.

 

Figure 9

NOTE: If you are using an Emerson Light Fixture with your fan, see Light Fixture Owner’s Manual for wiring.

2.Securely connect the fan motor white wire to the supply white (neutral) wire using wire connector supplied (Figure 9). Securely connect the fan motor black wire and blue wire to the supply black (hot) wire using wire connector supplied (Figure 9). After connections have been made, turn leads upward and carefully push leads into the outlet box, with the white and green leads on one side of the outlet box and the black and blue leads on the other side of the outlet box.

!WARNING

Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result.

3.Screw the two 1-1/4”threaded studs (supplied) into the tapped holes in the hanger bracket (Figure 10).

4.Lift the ceiling cover up to the threaded studs and switchturn until. studs protrude through the holes in the ceiling cover (Figure 10).

5.Secure the ceiling cover in place by sliding lockwashers (supplied) over the threaded studs and installing the two knurled knobs (supplied). (Figure 10.) Tighten the knurled knobs securely until the ceiling cover fits snugly against the ceiling and the hole in the ceiling cover is clear of the downrod. Your fan is now wired to be turned on and off from the fan

1-1/4"

 

THREADED

 

STUD

CEILING COVER

LOCKWASHER

 

KNURLED KNOB

 

Figure 10

!WARNING

To avoid possible fire or shock, make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling.

Installing Fan Blades

1.Use four 10-32x 3/8” pan head screws and flat washers (supplied) to secure the flange to the fan blade (ordered separately) (Figure 11). Repeat for the remaining four blades.

10-32x 3/8"

PAN HEAD SCREW

FLAT WASHER

FAN BLADE

BLADE

FLANGE

Figure 11

6

2.Use the 10 round recessed holes in the motor hub marked with "5" and install the five blade assemblies in accordance with Step 3.

3.Attach one blade assembly to the motor hub using two 10-32x 5/8" oval head screws (supplied) (Figure 12). Do not tighten completely at this time. Install four remaining blade assemblies in the same way. Gently snug all flange screws to the motor hub, working around the hub in a clockwise sequence. Next, securely tighten all flange screws, again working in a clockwise sequence. Failure to follow this procedure could result in fan wobble. This completes the blade installation.

MOTOR

HUB

 

10-32x 5/8"

Figure 12

OVAL HEAD SCREW

 

(2 Per Blade Assembly)

!WARNING

To reduce the risk of personal injury, do not bend the blade flanges when installing the flanges, balancing the blades, or cleaning the fan. Do not insert foreign objects between rotating fan blades.

4.Slip the pull chain through the bushing in the switch housing cover. Position the switch housing cover on the switch housing and secure using two 8-32x 3/8” screws (supplied) (Figure 13). Secure the pendant (supplied) to the pull chain using the connector (supplied).

Using Your Ceiling Fan

1.Restore electrical power to the outlet box by turning the electricity on at the main fuse box.

2.Check the operation of the fan by gently pulling on the 4-positionspeed control pull chain switch. The operating sequence is as follows:

REVERSING

THREE-SPEED

SWITCH

 

1st Pull—HIGH

 

2nd Pull—Medium

 

3rd Pull—Low

 

4th Pull—OFF

SPEED CONTROL

PULL CHAIN SWITCH

3.If airflow is desired in opposite direction, turn your fan off and wait for the blades to stop turning, then press the rocker switch located on top of the motor housing, and turn the fan on again. The fan blades will turn in the opposite direction and reverse airflow.

Attaching Light Kit

To install an accessory light kit, remove the two screws securing the switch housing cover to the switch housing. Remove the screw plug from the bottom of the switch housing cover and install the light kit in accordance with the light kit Owner's Manual.

!WARNING

To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring.

 

 

 

Maintenance

 

 

 

IMPORTANT CARE INSTRUCTIONS

 

 

 

for your Ceiling Fan

 

 

 

Periodic cleaning of your new ceiling fan is the only

 

 

 

maintenance that is needed.

 

 

 

When cleaning, use only a soft brush or lint free cloth

 

 

 

to avoid scratching the finish.

SWITCH

 

 

Abrasive cleaning agents are not required and should

HOUSING

PULL

 

be avoided to prevent damage to finish.

COVER

8-32x 3/8" SCREW

 

 

CHAIN

! WARNING

Figure 13

 

 

 

 

 

 

 

 

Do not use water when cleaning your ceiling fan. It

 

 

 

could damage the motor or the blades and create the

 

 

7

possibility of an electrical shock.

 

 

 

! WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN.

Trouble Shooting

TROUBLE

 

PROBABLE CAUSE

 

SUGGESTED REMEDY

 

 

 

 

 

1. Fan will not start.

1.

Fuse or circuit breaker blown.

1.

Check main and branch circuit fuses or circuit

 

 

 

 

breakers.

 

 

 

!

WARNING: Make sure main power is turned off.

 

2.

Loose power line connections to the fan, or loose

2.

Check line wire connections to fan and switch

 

 

switch wire connections in the switch housing.

 

wire connections in the switch housing.

 

 

 

 

 

2. Fan sounds noisy.

1.

Blades not attached to fan.

1.

Attach blades to fan before operating.

 

2.

Loose screws in motor housing.

2.

Check to make sure all screws in motor housing

 

 

 

 

are snug (not over-tight).

 

3.

Screws securing fan blade flanges to motor hub

3.

Check to make sure the screws which attach

 

 

are loose.

 

the fan flanges to the motor hub are tight.

 

 

 

!

WARNING: Make sure main power is turned off.

 

4.

Wire connectors inside switch housing rattling.

4.

Check to make sure wire connectors in

 

 

 

 

switch housing are not rattling against each

 

 

 

 

other or against the interior wall of the switch

 

 

 

 

housing.

 

5

Screws holding blades to flanges are loose.

5.

Tighten screws securely.

 

 

 

 

 

3. Fan wobbles

1.

Setscrew in motor coupling is loose.

1.

Raise motor cover and tighten setscrew securely.

excessively.

2.

Setscrew in hanger ball/downrod assembly is

2.

Tighten the setscrew in the hanger ball/downrod

 

 

 

loose.

 

assembly.

 

3.

Screws securing fan blade flanges to motor hub

3.

Check to be sure screws which attach the fan blade

 

 

are loose.

 

flanges to the motor hub are tight.

 

4.

Fan blade flanges not seated properly.

4.

Check to be sure the fan blade flanges seat firmly and

 

 

 

 

uniformly to the surface of the motor hub. If flanges are

 

 

 

 

seated incorrectly, loosen the flange screws and

 

 

 

 

retighten according to step 3 in the section “Installing

 

 

 

 

Fan Blades”.

 

5.

Hanger bracket and/or ceiling outlet box is not

5.

Tighten the hanger bracket screws to the outlet box,

 

 

securely fastened.

 

and/or secure outlet box.

 

6.

Fan blades out of balance.

6.

Interchanging an adjacent (side-by-side)blade pair can

 

 

 

 

redistribute the weight and result in smoother operation.

 

 

 

 

Or use supplied balancing kit to balance blades.

 

 

 

 

 

 

 

 

 

 

Accessories

1.Ceiling Fan Light Kits (see store or catalog).

2.Downrod Extension Kits (see store or catalog).

3.Ceiling Fan Controls (see store or catalog).

!WARNING

The use of any other control not specifically approved for this fan could result in fire, shock and personal injury.

!WARNING

This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Electric, Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric, Co. could result in personal injury or property damage.

Before discarding packaging material, be certain all parts have been removed.

HOW TO ORDER REPAIR PARTS

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:

PART NUMBER

PART DESCRIPTION

NAME OF ITEM

MODEL NUMBER

For repair parts, phone 1-800-654-3545.

8

Repair Parts

2

1

3

16

14

6

15

18 17 17

1813

31

30

27

5

4

 

29

21

22

23

8

7

25

 

9

 

26

19

10

28

24

20

1211

9

Repair Parts Listing

 

Key

 

 

 

Part Numbers

 

 

 

 

No.

Description

CF2000AB02

CF2000AW02

CF2000BC02

CF2000PW02

CF2000WB02

CF2000WW02

CF2000ORB02

 

1

Hanger Bracket Assy.

760732

760732

760732

760732

760732

760732

760732

 

 

Hanger Ball Assembly,

761632-25

761632-24

761632-52

761632-28

761632-29

761632-26

761632-71

 

 

Consisting of:

 

 

 

 

 

 

 

 

2

Hanger Ball

 

3

Downrod

 

 

Parts Bag Containing:

762392

762392

762392

762392

762392

762392

762392

 

4

Pin, Clevis (1)

 

5

Clip, Hairpin (1)

 

11

Coupling (1)

 

12

Pendant (1)

 

14

Wire Connector (3)

 

15

Wrench, Setscrew (1)

 

16

Stud, Threaded 1-1/4”(2)

 

17

Lockwasher (4)

 

18

Knob, Knurled (4)

 

19

Screw, 10-32x 5/8” (11)

10

20

Screw, 8-32x 3/8” (2)

21

Screw, 10-32x 3/8” (21)

 

 

22

Washer, Flat (21)

 

29

Setscrew, Hex Socket (1)

 

30

Stud, Threaded, 1” (2)

 

6

Ceiling Canopy

760169-2

760169-32

760169-35

760169-33

760169-30

760169

760169-41

 

7

Hub, Rubber

760601

760601

760601

760601

760601

760601

760601

 

8

Blade Assembly (Full set for one fan)

*

*

*

*

*

*

*

 

9

Flange Set (Full set for one fan)

762203

762203-3

762203-6

762203-4

762203-5

762203-1

762203-7

 

10

Switch Housing Assy.

762113-2

762113-5

762113-9

762113-6

762113-7

762113-3

762113-14

 

13

Cover, Motor

761621-3

761621-20

761621-23

761621-21

761621-17

761621

761621-25

 

23

Motor

762508

762508

762508

762508

762508

762508

762508

 

24

Cover, Switch Housing Assembly

761515-5

761515-8

761515-11

761515-9

761515-10

761515-6

761515-12

 

25

Washer, 9/16”

 

26

Lockwasher, 9/16”

 

27

Aux. Capacitor

762243

762243

762243

762243

762243

762243

762243

 

28

Harness, Wiring

762090-4

762090-4

762090-4

762090-4

762090-4

762090-4

762090-4

 

30

Screw, #8 Washerhead, 8-32x 3/8” (4)

 

Owner's Manual

BP7323-1

BP7323-1

BP7323-1

BP7323-1

BP7323-1

BP7323-1

BP7323-1

*Fan blade assemblies are purchased separately.