Einhell BG-DP 7535 User Manual



Bedienungsanleitung

Schmutzwasserpumpe

t

Operating Instructions
Dirty Water Pump

p

Mode d’emploi
Pompe eaux usées

C

Istruzioni per l’uso
Pompa per acque reflue

lL

Betjeningsvejledning
Spildevandspumpe

A

Használati utasítás
Szennyvízszivattyú

Bf

Upute za uporabu
Pumpa za prljavu vodu

4

Uputstva za upotrebu
Pumpa za prljavu vodu



Art.-Nr.: 41.705.93 I.-Nr.: 01018

BG-DP

7535

Anleitung_BG_DP_7535_SPK1:_ 11.06.2008 10:40 Uhr Seite 1

2

 Vor Inbetriebnahme Bedienungsanleitung und

Sicherheitshinweise lesen und beachten

 Read and follow the operating instructions and safety information

before using for the first time.

 Avant la mise en service, lisez le mode dʼemploi et les consignes

de sécurité et respectez-les.

 Prima della messa in esercizio leggete e osservate le istruzioni

per lʼuso e le avvertenze di sicurezza.

 Betjeningsvejledningen og sikkerhedsanvisningerne skal læses,

inden maskinen tages i brug. Alle anvisninger skal følges.

 Üzembehelyezés előtt elolvasni és figyelembe venni a használati

utasítást és a biztonsági utasításokat.

Bf Prije puštanja u rad pročitajte i pridržavajte se ovih uputa za uporabu

i sigurnosnih napomena.

4 Prije puštanja u pogon pročitajte i uvažite uputstva za upotrebu i

napomene bezbednosti.



Anleitung_BG_DP_7535_SPK1:_ 11.06.2008 10:40 Uhr Seite 2

3

1

4

3

2

1

2

1”

1”

1 1/2”

Anleitung_BG_DP_7535_SPK1:_ 11.06.2008 10:40 Uhr Seite 3

8

GB

 Important!

When using equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating manual with due
care. Keep this manual in a safe place, so that the
information is available at all times. If you give the
equipment to any other person, give them these
operating instructions as well.
We accept no liability for damage or accidents which
arise due to non-observance of these instructions
and the safety information.

1. Safety regulations



Caution!
In stagnant water bodies, garden ponds,
swimming ponds and their surrounding areas
the unit may only be used with an earth-leakage
circuit breaker with an actuating rated current of
up to 30 mA (according to VDE 0100 Part 702
and 738).

The equipment is not designed for use in
swimming pools and paddling pools of any kind
or other bodies of water in which people or
animals may be present during operation. It is
prohibited to operate the equipment if a person
or animal is in the danger area. Ask your
electrician!

This equipment is not designed to be used by people
(including children) with limited physical, sensory or
mental capacities or those with no experience and/or
knowledge unless they are supervised by a person
who is responsible for their safety or they have
received instructions from such a person in how to
use the equipment safely. Children must always be
supervised in order to ensure that they do not play
with the equipment.

Important!

 Before you put the equipment into operation,

arrange for a specialist to check that the

- earthing

- protective multiple earthing

- residual-current operated circuit-breaker circuit
comply with the safety regulations of the power
supply company and work correctly.

 The electrical plug-in connections must be

protected from wet conditions.

 If there is a risk of flooding, place the plug-in

connections in an area which is safe from
flooding.

 Strictly avoid pumping aggressive liquids and

abrasive substances.

 Protect the equipment from frost.
 Protect the equipment from dry running.
 Take suitable measures to keep the equipment

out of the reach of children.

 CAUTION!

Read all safety regulations and instructions.

Any errors made in following the safety regulations
and instructions may result in an electric shock, fire
and/or serious injury.

Keep all safety regulations and instructions in a
safe place for future use.

2. Layout (Fig. 1)

1. Handle

2. Universal hose connection

3. Intake cage

4. Floating switch

3. Proper use

The equipment you have purchased is designed to
pump water with a maximum temperature of 35 °C.
This equipment must never be used for other liquids,
especially engine fuels, cleaning agents and other
chemically-based products! Installed in a shaft, the
equipment provides protection from flooding.
However, it can be used wherever you want to move
water, e.g. in the house, in the garden, and for many
other applications. The equipment must not be used
to operate swimming pools!

If you want to use the equipment in bodies of water
with a natural, muddy bottom, place the equipment in
a slightly elevated position, e.g. on bricks.

The equipment is not designed for continuous
operation, e.g. as a circulating pump in a pond. In this
case the equipment’s anticipated life will be greatly
shortened because the equipment was not designed
for continuous loading.

The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.

Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the

Anleitung_BG_DP_7535_SPK1:_ 11.06.2008 10:40 Uhr Seite 8

GB

9

machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Mains connection 230V ~ 50 Hz
Power rating 750 W
Max. pumping rate 15,000 l/h
Max. delivery head 8 m
Max. immersion depth 8 m
Max. water temperature 35 °C
Hose connection 1 1/2“ female thread
Max. size of foreign bodies: Ø 35 mm
Switching point height: ON max. approx. 50 cm
Switching point height: OFF min. approx. 5 cm

5. Before putting the equipment into

operation

5.1 Installation

The equipment can be installed either:

 Stationary with rigid tubing

or

 Stationary with a flexible hose line

Note:

The maximum pumping rate is possible only with the
largest possible line diameter; if smaller hoses or
tubes are connected, the pumping rate will be
reduced. If the universal hose connection (Fig. 1/Item

2) is used, it should be shortened (as shown in Fig. 2)
to the connection actually used in order not to reduce
the pumping rate unnecessarily. Flexible hoses must
be fastened to the universal hose connection with a
hose clip (not included in the scope of supply).

Note!

When installing, never hang the equipment by the
discharge line or by the power cable. The equipment
must be hung up with the provided carry handle or it
must rest on the bottom of the shaft. To ensure that
the equipment works properly, the bottom of the shaft
always must be free of sludge and other
accumulations of dirt. If the water level is too low, the
sludge in the shaft can quickly dry out and hinder the
equipment from starting. It is necessary therefore to
check the equipment regularly (carry out trial start­ups).

Note:

The pump shaft should measure at least
40 x 40 x 50 cm so that the floating switch can move
freely.

5.2 Mains connection

The equipment you have purchased comes with an
earthing-pin plug. The equipment is designed for
connection to a socket outlet with earthing contact for
230 V ~ 50 Hz. Make sure that the socket-outlet is
sufficiently fused (at least 6 A) and in good working
order. Insert the power plug in the socket-outlet and
the equipment is ready for operation.

Important!

To rule out danger, this work must be left strictly to a
specialist electrician or Customer Service.

6. Operation

You can put the equipment into operation after you
have thoroughly read the installation and operating
instructions. Pay attention to the following points:

 Make sure that the equipment is set up securely.
 Check that the discharge line is fitted correctly.
 Make sure that the electrical connection is 230 V

~ 50 Hz.

 Check that the electrical socket-outlet is in good

working order.

 Make sure that no moisture or water can ever

reach the power connection.

 Make sure that the equipment does not run dry.

Setting the ON/OFF switching point:

The ON/OFF switching point of the floating switch can
be adjusted by shifting the floating switch in the
floating switch notched holder. Check the following
points before putting the equipment into operation:

 The floating switch must be fitted so that the

switching point height: ON and the switch point
height: OFF can be reached easily and with little
force. Check this by placing the equipment in a
container filled with water and carefully raising
and lowering the floating switch with your hand.
You can then see whether the equipment
switches on and off.

 Make sure that the distance between the floating

switch head and the cable holder is not too small.
If the distance is too small, there is no guarantee
that the equipment will work correctly.

 When adjusting the floating switch, make sure

that the floating switch does not touch the bottom
before the equipment is switched off. Important!
Risk of dry running.

Anleitung_BG_DP_7535_SPK1:_ 11.06.2008 10:40 Uhr Seite 9

10

GB

7. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after­sales service or similarly trained personnel to avoid
danger.

8. Cleaning, maintenance and

ordering of spare parts

Important!

 Unplug the power plug prior to any maintenance

work.

 For mobile applications, the equipment should be

cleaned with clear water after every usage.

 For stationary installation, it is recommended that

you check the floating switch for proper
functioning every three months.

 Use a water jet to remove any lint or fibrous

particles that may have become trapped in the
housing.

 Remove sludge from the shaft bottom and clean

the shaft walls every 3 months.

 Use clear water to remove deposits from the

floating switch.

8.1 Cleaning the paddle wheel

If a lot of deposits collect in the housing, the bottom
part of the equipment must be dismantled as follows:

1. Disconnect the intake cage from the housing.

2. Clean the paddle wheel with clear water.

Important! Do not put down or rest the
equipment on the paddle wheel!

3. Assemble in reverse order.

8.2 Maintenance

There are no parts inside the equipment which
require additional maintenance.

8.3 Ordering replacement parts:

Please quote the following data when ordering
replacement parts:

 Type of machine
 Article number of the machine
 Identification number of the machine
 Replacement part number of the part required

For our latest prices and information please go to
www.isc-gmbh.info

9. Disposal and recycling

The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.

Anleitung_BG_DP_7535_SPK1:_ 11.06.2008 10:40 Uhr Seite 10

11

GB

Faults Cause Remedy

The equipment does not start

- Power supply not connected

- Floating switch does trigger

- Check power supply

- Raise position of floating switch

The equipment does not pump

- Intake sieve clogged

- Discharge hose kinked

- Clean intake sieve with water jet

- Unkink the hose

The equipment does not cut out

- Floating switch cannot sink - Place equipment correctly on
shaft bottom

Insufficient pumping rate

- Intake sieve clogged

- Performance reduced due to

heavily contaminated and
abrasive water impurities

- Clean intake sieve

- Clean equipment and replace

wear parts

The equipment switches off after
briefly running

- Motor circuit-breaker switches

the equipment off due to
excessive water contamination

- Water temperature too high;

motor circuit-breaker switches
the equipment off

- Unplug power plug and clean
equipment and shaft

- Ensure that maximum
permissible water temperature
(35 °C) is not exceeded

10. Troubleshooting guide

Anleitung_BG_DP_7535_SPK1:_ 11.06.2008 10:40 Uhr Seite 11

36

k

erklärt folgende Konformität gemäß EU-Richtlinie
und Normen für Artikel

t

declares conformity with the EU Directive
and standards marked below for the article

p

déclare la conformité suivante selon la
directive CE et les normes concernant lʼarticle



verklaart de volgende conformiteit in overeen­stemming met de EU-richtlijn en normen voor
het artikel

m

declara la siguiente conformidad a tenor de la
directiva y normas de la UE para el artículo

O

declara a seguinte conformidade de acordo
com a directiva CE e normas para o artigo

U

förklarar följande överensstämmelse enl. EU­direktiv och standarder för artikeln

q

ilmoittaa seuraavaa Euroopan unionin direkti­ivien ja normien mukaista yhdenmukaisuutta
tuotteelle



erklærer herved følgende samsvar med EU­direktiv og standarder for artikkel

T

заявляет о соответствии товара
следующим директивам и нормам EC

B

izjavljuje sljedeću uskladjenost s odredbama i
normama EU za artikl.

Q

declarå urmåtoarea conformitate cu linia direc­toare CE μi normele valabile pentru articolul.

Z

ürün ile ilgili olarak AB Yönetmelikleri ve
Normlar∂ gere©ince aμa©∂daki uygunluk aç∂kla
mas∂n∂ sunar.

z

‰ЛПТУВИ ЩЛУ ·ОfiПФ˘ıЛ Ы˘МКˆУ›· Ы‡МКˆУ· МВ
ЩЛУ √‰ЛБ›· ∂∂ О·И Щ· ЪfiЩ˘Ф БИ· ЩФ ЪФ˚fiУ

C dichiara la seguente conformità secondo la

direttiva UE e le norme per lʼarticolo

l

attesterer følgende overensstemmelse i
henhold til EU-direktiv og standarder for produkt

j

prohlašuje následující shodu podle směrnice
EU a norem pro výrobek.

A

a következő konformitást jelenti ki a termékek­re vonatkozó EU-irányvonalak és normák szerint

X

pojasnjuje sledečo skladnost po smernici EU
in normah za artikel.



deklaruje zgodność wymienionego poniżej
artykułu z następującymi normami na
podstawie dyrektywy WE.

W

vydáva nasledujúce prehlásenie o zhode podľa
smernice EÚ a noriem pre výrobok.

e

деклаpиpа следното съответствие съгласно
диpективите и ноpмите на ЕС за пpодукта.

1

заявляє про відповідність згідно з Директивою
ЄС та стандартами, чинними для даного товару

.

deklareerib vastavuse järgnevatele EL direktiivi
dele ja normidele

G

deklaruoja atitikti pagal ES direktyvas ir normas
straipsniui

4

izjavljuje sledeçi konformitet u skladu s odred
bom EZ i normama za artikl

H

Atbilstības sertifikāts apliecina zemāk minēto preču
atbilstību ES direktīvām un standartiem

E

Samræmisyfirl‡sing sta›festir eftirfarandi samræmi
samkvæmt reglum Evfrópubandalagsins og stö›lum
fyrir vörur

Konformitätserklärung

ISC-GmbH · Eschenstraße 6 · D-94405 Landau/Isar

Schmutzwasserpumpe BG-DP 7535

Art.-Nr.: 41.705.93 I.-Nr.: 01018 Archivierung: 4170580-42-4155050
Subject to change without notice

EN 60335-1; EN 60335-2-41; EN 50366;

EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3

Landau/Isar, den 13.02.2008

Wang

Product-Management

Weichselgartner

General-Manager

98/37/EC

2006/95/EC

97/23/EC

2004/108/EC

90/396/EEC

89/686/EEC

87/404/EEC

R&TTED 1999/5/EC

2000/14/EC_2005/88/EC:

95/54/EC:

97/68/EC:

X

X

Anleitung_BG_DP_7535_SPK1:_ 11.06.2008 10:40 Uhr Seite 36

37

k Nur für EU-Länder

Werfen Sie Elektrowerkzeuge nicht in den Hausmüll!

Gemäß europäischer Richtlinie 2002/96/EG über Elektro- und Elektronik-Altgeräte und Umsetzung in
nationales Recht müssen verbrauchte Elektrowerkzeuge getrennt gesammelt werden und einer
umweltgerechten Wiederverwertung zugeführt werden.

Recycling-Alternative zur Rücksendeaufforderung:
Der Eigentümer des Elektrogerätes ist alternativ anstelle Rücksendung zur Mitwirkung bei der sachge­rechten Verwertung im Falle der Eigentumsaufgabe verpflichtet. Das Altgerät kann hierfür auch einer
Rücknahmestelle überlassen werden, die eine Beseitigung im Sinne der nationalen Kreislaufwirtschafts­und Abfallgesetze durchführt. Nicht betroffen sind den Altgeräten beigefügte Zubehörteile und Hilfsmittel
ohne Elektrobestandteile.

t For EU countries only

Never place any electric tools in your household refuse.

To comply with European Directive 2002/96/EC concerning old electric and electronic equipment and its
implementation in national laws, old electric tools have to be separated from other waste and disposed of
in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the demand to return electrical devices:
As an alternative to returning the electrical device, the owner is obliged to cooperate in ensuring that the
device is properly recycled if ownership is relinquished. This can also be done by handing over the used
device to a returns center, which will dispose of it in accordance with national commercial and industrial
waste management legislation. This does not apply to the accessories and auxiliary equipment without
any electrical components which are included with the used device.

p Uniquement pour les pays de l'Union Européenne

Ne jetez pas les outils électriques dans les ordures ménagères.

Selon la norme européenne 2002/96/CE relative aux appareils électriques et systèmes électroniques
usés et selon son application dans le droit national, les outils électriques usés doivent être récoltés à
part et apportés à un recyclage respectueux de l'environnement.

Possibilité de recyclage en alternative à la demande de renvoi :
Le propriétaire de lʼappareil électrique est obligé, en guise dʼalternative à un envoi en retour, à contribuer
à un recyclage effectué dans les règles de lʼart en cas de cessation de la propriété. Lʼancien appareil
peut être remis à un point de collecte dans ce but. Cet organisme devra lʼéliminer dans le sens de la Loi
sur le cycle des matières et les déchets. Ne sont pas concernés les accessoires et ressources fournies
sans composants électroniques.

Anleitung_BG_DP_7535_SPK1:_ 11.06.2008 10:40 Uhr Seite 37

t

GUARANTEE CERTIFICATE

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely
event that your device develops a fault, please contact our service department at the address shown on this
guarantee card. Of course, if you would prefer to call us then we are also happy to offer our assistance under
the service number printed below. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights.
We do not charge you for this guarantee.

2. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the
rectification of these defects or replacement of the device. Please note that our devices have not been
designed for use in commercial, trade or industrial applications. Consequently, the guarantee is invalidated
if the equipment is used in commercial, trade or industrial applications or for other equivalent activities. The
following are also excluded from our guarantee: compensation for transport damage, damage caused by
failure to comply with the installation/assembly instructions or damage caused by unprofessional
installation, failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or
current type), misuse or inappropriate use (such as overloading of the device or use of non-approved tools
or accessories), failure to comply with the maintenance and safety regulations, ingress of foreign bodies
into the device (e.g. sand, stones or dust), effects of force or external influences (e.g. damage caused by
the device being dropped) and normal wear resulting from proper operation of the device.

The guarantee is rendered null and void if any attempt is made to tamper with the device.

3. The guarantee is valid for a period of 2 years starting from the purchase date of the device. Guarantee
claims should be submitted before the end of the guarantee period within two weeks of the defect being
noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee
period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases,
the work performed or parts fitted will not result in an extension of the guarantee period, and no new
guarantee will become active for the work performed or parts fitted. This also applies when an on-site
service is used.

4. In order to assert your guarantee claim, please send your defective device postage-free to the address
shown below. Please enclose either the original or a copy of your sales receipt or another dated proof of
purchase. Please keep your sales receipt in a safe place, as it is your proof of purchase. It would help us if
you could describe the nature of the problem in as much detail as possible. If the defect is covered by our
guarantee then your device will either be repaired immediately and returned to you, or we will send you a
new device.

Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the
scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send
the device to our service address.

44

Anleitung_BG_DP_7535_SPK1:_ 11.06.2008 10:40 Uhr Seite 44