D-link DUB-E100 User Manual [ru]

Version 5.0 | 12/15/2014

User Manual

USB 2.0 10/100 Fast Ethernet Adapter

DUB-E100

Table of Contents

Manual Overview

D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any
person or organization of such revisions or changes. Information in this document may become obsolete as our services and
websites develop and change. Please refer to the www.dlink.com website for the most current information.

Trademarks

D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United
States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of
their respective companies.
Copyright © 2014 by D-Link Corporation.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission
from D-Link Corporation.

iD-Link DUB-E100 User Manual

Table of Contents

Table of Contents

Product Overview .............................................................. 1

Package Contents .........................................................................1

System Requirements ................................................................. 1

Introduction ................................................................................... 2

Features ............................................................................................2

Hardware Overview ..................................................................... 3

Installation ......................................................................... 4

Software Installation ................................................................... 4

Windows 7/8 ...........................................................................4

Windows Vista ........................................................................ 6

Windows XP ............................................................................ 7

Mac OS X ................................................................................10

Linux 2.6.14 ...........................................................................13

Connecting the Adapter to a Network ...............................14

Completing the Installation ....................................................15

Troubleshooting .............................................................. 16

Technical Specifications .................................................. 18

iiD-Link DUB-E100 User Manual

Section 1 - Product Overview

Package Contents

• DUB-E100 USB 2.0 10/100 Fast Ethernet Adapter

• DUB-E100 Drivers and Manual on CD-ROM

• Quick Installation Guide

If any of the above items are missing or damaged, please contact your reseller.

System Requirements

System Requirements

Computer with the following:

• Microsoft Windows® 8/7/Vista®/XP/2000, Linux, or Mac OS X 10.5/10.9

• Pentium 2.0 GHz or higher with a minimum of 32 MB RAM

• Available USB port

• CD-ROM drive

1D-Link DUB-E100 User Manual

Section 1 - Product Overview

Introduction

Thank you for choosing the D-Link DUB-E100 USB 2.0 10/100 Fast Ethernet Adapter. The DUB-E100 USB 2.0 10/100 Mbps Fast
Ethernet Adapter is specically designed to plug into an available Universal Serial Bus (USB) port on a desktop or laptop PC
running Microsoft Windows 8/7/Vista/XP/2000, Mac OS X, or Linux. Based on USB 2.0, the DUB-E100 extends the transfer speed
of earlier USB Fast Ethernet adapters to true 10/100 Mbps connectivity. Power for the DUB-E100 is provided directly by the USB
bus, eliminating the need for an external power adapter. It also supports USB energy-saving suspend and resume functions
to minimize power consumption, which is especially useful for laptop/notebook users.

Features

Designed for versatility and performance, the DUB-E100 USB 2.0 10/100 Fast Ethernet Adapter provides the following:

• Compliant with USB 2.0 and USB 1.1 specications

• True 10/100 Mbps network connectivity

• Compliance with IEEE 802.3u Fast Ethernet standards and IEEE 802.3 Ethernet standards

• Plug-and-Play installation

• Auto 10/100 Mbps speed detection

• Supports half and full-duplex at 10 Mbps, half and full-duplex at 100 Mbps

• One built-in RJ-45 connector

• Auto-negotiation to the highest available speed

• Two LED indicators: Link, TX/RX

• Driver support:

• Microsoft Windows 7/8 (x86, x64)

• Microsoft Windows Vista (x86, x64)

• Microsoft Windows XP (x86/x64 Edition)

• Linux (kernel 2.6.14 & above)

• Macintosh OS X (10.5,10.9)

• Microsoft Windows 2000

2D-Link DUB-E100 User Manual

Section 1 - Product Overview

Ethernet Port

Hardware Overview

USB Connector

COMPONENT DESCRIPTION

Ethernet Port Plug an Ethernet cable from a switch, hub, or router into this port.

USB Connector Plug this connector into a USB port on your PC.

3D-Link DUB-E100 User Manual

Section 2 - Installation

Software Installation

Insert the DUB-E100 CD into your computer’s DVD or CD drive, then proceed to the appropriate installation section on the
following pages for your operating system.

Note: If the user interface does not start up, please go to the Autorun folder in your PC’s CD drive and open Autorun manually.

Windows 7/8

After you put the CD into the CD drive, the DUB-E100 user interface menu
screen will appear. Click on Install to begin the DUB-E100 driver installation.
The InstallShield Wizard will then pop up and run automatically.

Note: The DUB-E100 user interface may dier in appearance for dierent
regions.

4D-Link DUB-E100 User Manual

Section 2 - Installation

When the InstallShield Wizard is completed, plug the DUB-E100 into your PC
and the driver software installation will be completed automatically.

When the Windows 7/8 driver installation is complete, please then proceed
to Connecting the Adapter to a Network on page 14.

5D-Link DUB-E100 User Manual

Section 2 - Installation

Windows Vista

After you put the CD into the CD drive, the DUB-E100 user interface menu
screen will appear. Click on Install to begin the DUB-E100 driver installation.
The InstallShield Wizard will then pop up.

Note: The DUB-E100 user interface may dier in appearance for dierent
regions.

Plug the DUB-E100 into your PC and the driver software installation will be
completed automatically.

When the Windows Vista driver installation is complete, you can connect
the DUB-E100 to a USB port on your computer. Please then proceed to
Connecting the Adapter to a Network on page 14.

6D-Link DUB-E100 User Manual

Section 2 - Installation

Windows XP

After you put the CD into the CD drive, the DUB-E100 user interface menu
screen will appear. Click on Install to begin the DUB-E100 driver installation.
The InstallShield Wizard will then pop up.

Note: The DUB-E100 user interface may dier in appearance for dierent
regions.

Plug the DUB-E100 into your PC.

7D-Link DUB-E100 User Manual

Section 2 - Installation

The Found New Hardware box will appear. Select Yes, this time only and
click Next to continue.

Choose Install the software automatically and click Next to continue.

8D-Link DUB-E100 User Manual

Section 2 - Installation

When the Windows XP driver installation is complete, you can connect
the DUB-E100 to a USB port on your computer. Please then proceed to
Connecting the Adapter to a Network on page 14.

9D-Link DUB-E100 User Manual

Section 2 - Installation

Mac OS X

The following screenshots were taken from Mac OS X 10.5, but the steps are similar in other versions of OS X. Your operating
system must be version 10.4 or above.

Please insert the DUB-E100 CD into your computer’s DVD or CD drive, then
go to the DUB-E100 folder and navigate to \Drivers\MAC.

Double-click DUB-E100_v3.0.0

10D-Link DUB-E100 User Manual

Section 2 - Installation

Click Continue.

Click Install to perform a standard installation. If you wish to change the
drive where the installation will take place, click Change Install Location.

11D-Link DUB-E100 User Manual

Section 2 - Installation

If you clicked Change Install Location, you will see the Destination Select
screen. Select a Destination Volume, then click Continue.

Enter the name and password of a user with administrative rights.
Click OK.

Click Continue Installation. The computer will then restart itself after the
installation is complete. Please then proceed to Connecting the Adapter
to a Network on page 14.

12D-Link DUB-E100 User Manual

Section 2 - Installation

Linux 2.6.14

This driver is designed for Kernel 2.6.14.x or above. To compile the provided Linux driver, you need the Linux 2.6 Kernel source.
Also, please make sure the kernel is built with “Support for Host-side, EHCI, OHCI, and UHCI” option. Please follow these steps.

1. Insert the CD into the CD drive of your computer and go to the Drivers\Linux\ directory.

2. Copy the DLink_DUB_E100_V4.13.100 folder to your temporary directory.

3.Go to the DLink_DUB_E100_V4.13.100 folder and execute the following command to compile
the driver.[root@DLink_DUB_E100_V4.13.100]# make

4. If compiling without errors, asix.ko will be created under the current directory.

5. If you want to use modprobe command to mount the driver, execute the following command to install the driver
on your Linux.
[root@DLink_DUB_E100_V4.13.100]# make install
To mount the driver, go to theDLink_DUB_E100_V4.13.100 directory and executing the following
command:[root@DLink_DUB_E100_V4.13.100]# insmod usbnet
[root@DLink_DUB_E100_V4.13.100]# insmod DUB_E100.ko
or
[root@DLink_DUB_E100_V4.13.100]# modprobe DUB_E100
To unmount the driver, just typing the following command:
[root@DLink_DUB_E100_V4.13.100]# rmmod DUB_E100
[root@DLink_DUB_E100_V4.13.100]# rmmod usbnet

Please then proceed to Connecting the Adapter to a Network on page 14.

13D-Link DUB-E100 User Manual

Section 2 - Installation

Connecting the Adapter to a Network

Attach an Ethernet cable to the Ethernet port on the DUB-E100.

Attach the other end of the Ethernet cable to your network switch, hub, or router.

14D-Link DUB-E100 User Manual

Section 2 - Installation

Completing the Installation

When the installation of the DUB-E100 is complete, the Speed LED will illuminate solid amber when the DUB-E100 is connected
to a 100 Mbps network and remains o when connected to a 10 Mbps network. The Tx/Rx LED will ash Green when data is
being transmitted or received. If both LEDs are unlit, there may be a problem with the physical connection. Check the cables
between your DUB-E100 and your switch or router. Verify that your network switch or router is powered on.

Speed LED

Lights solid amber when the network
connection is at 100 Mbps and remains o
when connected to a 10 Mbps network.

TX/RX LED

Flashes green when data is
being transmitted or received.

15D-Link DUB-E100 User Manual

Section 3 - Troubleshooting

Troubleshooting

Do I need to use a crossover cable or straight-through cable?

With most of D-Link’s switches/routers, the Ethernet ports are Auto MDI-II/MDI-X. This means the port will auto-sense the cable
type. Auto MDI-II/MDI-X ports may react dierently if the Ethernet cable is not properly pinned. If you make your own cables,
it is very important that they follow the industry standard pin-out (568A and 568B).

Computer connections to a hub, switch, or router typically use a straight-through cable. When connecting a computer to
another computer or to an uplink port then a cross-over cable is typically required. Rule of Thumb: ”If there is a link light, the
cable is right.”

How do I verify that my DUB-E100 is properly installed?

Windows

You can verify that the adapter has been properly installed in Device Manager by following these steps:

• Right-click on the My Computer icon and select Properties.

• For Windows XP, 2000, and Server 2003: Go to the Hardware tab and click on the Device Manager button

• For Windows Vista: Click on the Device Manager item under the Tasks group.

• Expand the Network Adapters heading by clicking on the plus (+) sign next to Network Adapters.

• Right-click on the My Computer icon and select Properties.

• The D-Link USB DUB-E100 should appear with a green and gold network adapter symbol.
If the D-Link USB DUB-E100 in Device Manager appears with a bright yellow exclamation mark or a red x, please
contact D-Link Technical Support.

Mac

• Click the Apple icon on the task bar, select System Preferences, and then click the Network icon.

• You will find that a new Ethernet network interface is available. It is usually named Ethernet Adapter (en1) or Ethernet
Adapter (en2).

16D-Link DUB-E100 User Manual

Section 3 - Troubleshooting

Linux 2.6.x

To verify if the DUB-E100 driver is properly installed:

• Load the DUB-E100 module by the following command:
[root@localhost linux2.6.14_rev101]# modprobe DUB_E100

• List the loaded modules with the specified pattern “DUB_E100”:
[root@localhost linux2.6.14_rev101]# lsmod | grep DUB_E100
Then you should get the reply similar to the following lines: asix
26880 0
usbnet 20616 1 DUB_E100
mii 9600 2 DUB_E100,e100
usbcore 114896 5 asix,usbnet,usb_storage,echi_hcd,uhci_hcd

If you still have a problem installing the D-Link DUB-E100 USB driver, please contact D-Link Technical Support.

17D-Link DUB-E100 User Manual

Appendix A - Technical Specications

Technical Specifications

Firmware Specications

OS

+ Microsoft Windows 8/7/Vista/XP/2000
+ Mac OS X 10.5/10.9
+ Linux

Hardware Specications

PACKAGE CONTENTS

+ DUB-E100 USB 2.0 Fast Ethernet Adapter
+ Quick Installation Guide
+ CD-ROM with:

- Drivers

- Manual

STANDARDS

+ USB Specication Version 2.0
+ USB Specication Version 1.1
+ USB Specication Version 1.0
+ OHCI (Open Host Controller Interface)
+ EHCI (Enhanced Host Controller Interface)
+ IEEE 802.3 Ethernet
+ IEEE 802.3u 100BASE-T, TX and T4 compatible
+ Supports suspended mode and remote wakeup
+ Supports full and half duplex in Fast Ethernet

POWER
+ Bus powered 2.5 W, 0.5 A@5 V DC

DIMENSIONS (W x D x H)

+ 73 x 21.3 x 20 mm (2.87 x 0.84 x 0.79 inches)

WEIGHT

+ 22 g (0.05 pounds)

OPERATING TEMPERATURE

+ Operating: 0 ˚ to 40 ˚C (32 ˚ to 104 ˚F)
+ Storage: -10 ˚ to 70 ˚C (14 ˚ to 158 ˚F)

HUMIDITY

+ Operating: 5% to 95% (non-condensing)
+ Non-operating: 0% to 95% (non-condensing)

CERTIFICATIONS

+ CE
+ C-Tick
+ FCC

PORTS/CONNECTORS

+ USB Type A
+ RJ-45 (10/100 Mbps Dual-Speed)

DIAGNOSTIC LEDS

+ Speed
+ Tx/Rx Trac

18D-Link DUB-E100 User Manual