D-Link DCS-4605EV User Manual

Version 1.00 | 06/19/2018
User Manual
Vigilance 5 megapixel H.265 Outdoor Dome Camera
DCS-4605EV
Preface
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Information in this document may become obsolete as our services and websites develop and change.
Revision Date Description
1.00 06/15/2018 DCS-4605EV Revision A1 with rmware version 1.00
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.
Copyright © 2018 D-Link Corporation.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation.
2D-Link DCS-4605EV User Manual
Table of Contents
Product Overview ........................................................4
Package Contents ................................................................. 4
Introduction ............................................................................ 5
System Requirements ......................................................... 5
Features .................................................................................... 6
Hardware Overview ............................................................. 7
Installation ...................................................................9
Mounting the Camera .........................................................9
Using the DCS-37-1 Mount (optional) .........................12
Using the DCS-37-2 Mount (optional) .........................14
Using the DCS-37-3 Mount (optional) .........................16
Waterproong Your Installation ....................................17
Software Installation ......................................................20
Conguration ............................................................23
Using the Conguration Interface ................................23
Advanced ...........................................................................60
Camera Conguration ...................................................67
Camera Options ..................................................................71
Camera Info .......................................................................71
Time .....................................................................................72
Administration Settings ...............................................75
Camera Log .......................................................................78
Technical Specications ............................................79
Regulatory Information ............................................ 83
Live Video ..............................................................................25
Setup Wizard ........................................................................27
Network Setup Wizard ..................................... 28
Motion Detection Setup Wizard ................................30
Settings ..................................................................................33
Network Settings ............................................................33
Camera Settings ..............................................................39
Recording Management ..............................................48
Advanced Setup ..................................................................60
3D-Link DCS-4605EV User Manual
Section 1: Product Overview
DCS-4605EV Vigilance 5 megapixel H.265 Outdoor Dome Camera
Cable Waterproong Connector
Mounting Kit
CD-ROM with User Manual and software
Product Overview

Package Contents

Quick Installation Guide
If any of the above items are missing, please contact your reseller.
Safety Notice: Installation and servicing should be done by certied technicians to conform with all local codes and prevent voiding your warranty.
4D-Link DCS-4605EV User Manual
Section 1: Product Overview

Introduction

The DCS-4605EV Vigilance 5 megapixel H.265 Outdoor Dome Camera is a professional surveillance and security solution for small, medium, and large enterprises. It uses a 5 megapixel progressive scan CMOS sensor to deliver low-noise video and low-light capability ideal for surveillance applications. The DCS-4605EV is a complete surveillance solution featuring a built-in IR cut lter and IR LEDs eective to 20 meters, allowing it to stream simultaneous real-time Full HD resolution video during the day or at night in indoor and outdoor environments.
The DCS-4605EV can be accessed remotely, controlled and congured from any computer over your local network or through the Internet via a web browser. The simple installation and intuitive web-based interface oer easy conguration across the full range of its advanced feature set, including granular control over multiple video streams with dierent congurations and multicast video streams that help you manage your video bandwidth.
The DCS-4605EV has an IP66-certied weatherproof housing designed for both indoor and outdoor applications. The DCS-4605EV also incorporates Power over Ethernet (PoE), allowing it to be easily installed in a variety of locations without the need for supplemental power cabling. The combination of IP66 weatherproof housing, IK10 vandal-proof housing, IR-Cut Filter, IR LEDs, and PoE make the DCS-4605EV an ideal solution for a dependable and cost-eective 24 hour surveillance solution with easy clutter-free installation.

System Requirements

Computer with Microsoft Windows® 10, 8, or 7
Internet Explorer 8, Firefox 20, or Chrome or higher
Existing 10/100 Ethernet-based network with an available 802.3af Power over Ethernet (PoE) port
5D-Link DCS-4605EV User Manual
Section 1: Product Overview

Features

H.265 Compression
The DCS-4605EV supports the latest H.265 compression algorithm to bring out the best performance in the compromise between quality, bandwidth, and storage space.
Simple to Maintain
The DCS-4605EV is a stand-alone system with a built-in CPU, requiring no special hardware or software. The DCS-4605EV can be viewed and managed through most web browsers, including Internet Explorer®, Firefox®, and Chrome®.
Supports a Variety of Platforms
With support for TCP/IP networking, HTTP, and other Internet related protocols, the DCS-4605EV can also be integrated easily into other Internet/ Intranet applications because of its standards-based features. The DCS-4605EV works in network that supports 10/100 Ethernet, making the DCS-4605EV easy to integrate into your existing network environment.
Advanced Event Management
The DCS-4605EV can be set up to send e-mail notications with snapshots when an event occurs, such as when motion is detected. Events can be triggered from several sources, such as motion detection and time-based events.
IR LEDs for Day and Night Functionality
The built-in infrared LEDs enable night time viewing of up to 20 meters.
IP66 Weatherproof and Vandal-proof Housing
The DCS-4605EV uses an IP66 weatherproof housing, allowing you to rest assured that in the toughest of conditions, it will continue to provide round-the-clock surveillance.
PoE (Power over Ethernet) for Flexible Installation
The DCS-4605EV can draw all the power it needs from a PoE switch or PoE injector for a simple and clutter-free installation.
Remote Monitoring Utility
The D-Link D-ViewCam™ application adds enhanced features and functionality for the camera and allows administrators to congure and access the camera from a separate site via Intranet or Internet. Other features include image monitoring, recording images to a hard drive, viewing up to 32 cameras on one screen, and taking snapshots.
6D-Link DCS-4605EV User Manual
Section 1: Product Overview
2

Hardware Overview

1
3
4
1 Cover Screws These four screws can be removed with the included wrench.
2 Protective Cover Protects the camera lens assembly from the environment.
3 Ethernet Port
4 Power Port Connects to an optional 12 V / 1.5 A power adapter (not included).
RJ-45 connector for Ethernet which can also be used to power the camera using Power over Ethernet (PoE).
7D-Link DCS-4605EV User Manual
Section 1: Product Overview
Hardware Overview
1
2
6
5
4
3
1 Tilt Lock Screw Can be loosened to adjust the camera's tilt angle.
2 Light Sensor Detects lighting levels and switches between day and night mode accordingly.
3
4 IR LEDs Provide illumination for low-light environments.
5 Reset Button Press and hold this button down for 10 seconds to reset the camera to factory default settings.
6 Camera Lens Camera lens to record video of the surrounding area.
microSD
Card Slot
Insert a microSD card for onboard storage of snapshots and video.
8D-Link DCS-4605EV User Manual
Section 2: Installation

Installation

Mounting the Camera

It is highly recommended that you congure and test your camera before mounting it.
Step 1
Place the mounting sticker where you want to position the camera.
Use a 6 mm drill bit to make the required holes approximately 25 mm deep, then insert the wall anchors into the holes.
Step 2 If you are running the camera cables through the wall, drill a hole in the center and pull
the cables through the hole.
Step 3
Use the included wrench to loosen the 4 screws on the top of the camera, then lift the camera cover o.
9D-Link DCS-4605EV User Manual
Section 2: Installation
Step 4
Use the screws provided to mount the camera to the wall.
If you are running the camera cables out the side of the camera, guide the camera cables through the cable channel on the base.
If you are mounting the camera to the ceiling, use a athead screwdriver to remove the plastic hole cover from the bottom of the base, then guide the cables through the bottom.
Step 5
Connect the power and Ethernet cables, or just the Ethernet cable if you are using a PoE connection.
10D-Link DCS-4605EV User Manual
Section 2: Installation
Step 6
Loosen the adjustment screw on the side of the lens assembly, then re-tighten it after adjusting the lens assembly to the desired vertical angle. The camera supports from 30° to 90° of tilt. You can also adjust the pan within a -120° to 120° range by rotating it clockwise or counter­clockwise.
When you are done adjusting the camera's angle, put the inner cover back into place.
Note: The camera has a limited range of motion; if it stops when you are adjusting it, do not attempt to rotate or tilt the camera any further in that direction.
Step 7
Use the screws provided to mount the camera to the ceiling.
Step 8
Re-attach the camera cover.
11D-Link DCS-4605EV User Manual
Section 2: Installation

Using the DCS-37-1 Mount (optional)

To mount the camera with the DCS-37-1 mount, follow the instructions below.
Step 1
Place the DCS-37-1 mounting sticker in the desired location, then use a 6 mm drill bit to drill the required holes 25 mm deep and insert the wall anchors into the holes. If you plan to pass cables through the wall, you will also need to drill a hole for the cable channel.
Note: The camera in the corresponding graphics may be dierent from your product, but the basic process is the same.
Step 2
Use the provided screws to mount the DCS-37-1 to the wall.
Step 3
Guide the camera connectors through the back or bottom cable channel on the DCS-37-1. Then screw the mounting plate to the bracket using the set of mounting holes marked B.
12D-Link DCS-4605EV User Manual
Section 2: Installation
Step 4
Remove the cover from the camera.
Use the provided screws to mount the camera to the DCS-37-1, then adjust the angle and rotation of the camera as desired using the tilt lock screw.
Step 5
Attach the camera cover.
If you are passing the camera cables through the wall, place the rubber stopper into the bottom cable channel on the mount to seal it.
13D-Link DCS-4605EV User Manual
Section 2: Installation

Using the DCS-37-2 Mount (optional)

To mount the camera with the DCS-37-2 mount, follow the instructions below.
Step 1
Place the DCS-37-2 mounting sticker in the desired location, then use a 6 mm drill bit to drill the required holes 25 mm deep and insert the wall anchors into the holes. If you plan to pass cables through the ceiling, you will also need to drill a hole for the cable channel.
Note: The camera in the corresponding graphics may be dierent from your product, but the procedure is the same.
Step 2
Use the provided screws to mount the DCS-37-2 to the wall using the inner mounting holes.
Step 3
Guide the camera connectors through the back or side cable channel on the DCS-37-2. Use the provided screws to mount the camera to the DCS-37-2 using the set of mounting holes marked B.
14D-Link DCS-4605EV User Manual
Section 2: Installation
Step 4
Remove the cover from the camera.
Use the provided screws to mount the camera to the DCS-37-2, then adjust the angle and rotation of the camera as desired using the tilt lock screw.
Step 5
Attach the camera cover.
If you are passing the camera cables through the ceiling, place the rubber stopper into the side cable channel to seal it.
15D-Link DCS-4605EV User Manual
Section 2: Installation

Using the DCS-37-3 Mount (optional)

To mount the camera with the DCS-37-3 mount, follow the instructions below.
Step 1
Place the DCS-37-3 mounting sticker in the desired location, then use a 6 mm drill bit to drill the required holes 25 mm deep and insert the wall anchors into the holes. If you plan to pass cables through the ceiling, you will also need to drill a hole for the cable channel.
Note: The camera in the corresponding graphics may be dierent from your product, but the procedure is the same.
Step 2
Use the provided screws to mount the DCS-37-3 to the ceiling using the inner mounting holes.
Step 3
Remove the cover from the camera.
Guide the camera connectors through the bottom cable channel on the DCS-37-3. Use the provided screws to mount the camera to the DCS-37-3 using the set of mounting holes marked
D.
Step 4
Remove the cover and adjust the angle and rotation of the camera as desired, then put the cover back in place. Screw the camera cover back in place.
Make sure the rubber stopper is in the side cable channel to seal it.
16D-Link DCS-4605EV User Manual
Section 2: Installation
Waterproong Your Installation
To waterproof your camera installation, follow the instructions below. Round Ethernet cable, a crimping tool, and RJ-45 plugs are required for this procedure.
Step 1
Place the washer around the base of the Ethernet connector as shown.
Step 2
Thread bare Ethernet cable through the waterproof connector as shown, then crimp an RJ-45 plug onto the cable.
Step 3
Crimp an RJ-45 connector onto the end of the cable.
Step 4
Connect the other end of the Ethernet cable to the camera's Ethernet port.
17D-Link DCS-4605EV User Manual
Section 2: Installation
Step 5
Connect the RJ-45 plug into the Ethernet connector, then screw the waterproof connector to the Ethernet connector by turning it about a half-turn clockwise.
Step 6
Screw the back part of the waterproof connector clockwise until there is a tight seal around the Ethernet cable.
If you are using PoE to power your camera, use the power connector cap to seal the power connector.
18D-Link DCS-4605EV User Manual
Section 2: Installation
If you are using a power adapter (not included) to power your camera, wind waterproof tape around the connection in an overlapping manner to cover it.
19D-Link DCS-4605EV User Manual
Section 2: Installation

Software Installation

Step 1
Insert the DCS-4605EV CD into your computer's CD-ROM drive to begin the installation.
If the Autorun function on your computer is disabled, or if the D-Link Launcher fails to start automatically, click the Start button and type D:\autorun.exe (where D: represents the drive letter of your CD-ROM drive) and press Enter.
Step 2 Click on the D-Link Setup Wizard SE icon that was created in your Windows Start menu (Start > D-Link > Setup Wizard SE).
20D-Link DCS-4605EV User Manual
Section 2: Installation
Step 3
The Setup Wizard will appear and display the MAC address and IP address of your camera(s). If you have a DHCP server on your network, a valid IP Address will be displayed. If your network does not use a DHCP server, the network camera's default static IP 192.168.0.20 will be displayed.
Select your camera, then click the Wizard button to continue.
Step 4
Enter the Admin ID and password. When logging in for the rst time, the default Admin ID is admin with the password left blank.
Click the checkboxes if you wish to change the admin ID and password for the camera, and enter the new ID and password you wish to use.
Click Next to continue.
21D-Link DCS-4605EV User Manual
Section 2: Installation
Step 5
Select DHCP if your camera obtains an IP address automatically from a DHCP server such as a router. Select Static IP if you want to manually enter the IP settings for the camera.
Click Next to continue.
Step 6
Take a moment to conrm your settings and click Restart.
22D-Link DCS-4605EV User Manual
Section 3: Conguration
Conguration
Using the Conguration Interface
After completing the Camera Installation Wizard, you are ready to use your camera. The camera’s built-in Web conguration utility is designed to allow you to easily access and congure your DCS-4605EV. At the end of the wizard, click Link, or enter the IP address of your camera into a web browser, such as Firefox. To log in, use the User name admin and the password you created in the Installation Wizard. If you did not create a password,
the default password is blank. After entering your password, click OK.
Step 1 Click on the D-Link Setup Wizard SE icon that was created in your Windows Start menu (Start > D-Link > Setup Wizard SE).
Step 2
Select the camera and click Link to access the web conguration.
The Setup Wizard will automatically open your web browser to the IP address of the camera.
23D-Link DCS-4605EV User Manual
Section 3: Conguration
Step 3
The first time you connect to the camera, you will be asked to set a password for the administrator account. After entering a password, click Save.
OR
Under Password, enter the same password congured during setup and click Login to continue.
Step 4
This section displays your camera’s live video. You can select your video prole and view or operate the camera.
24D-Link DCS-4605EV User Manual
Section 3: Conguration

Live Video

This section shows your camera’s live video. You may select any of the available icons listed below to operate the camera. You may also select your language using the drop-down menu on the left side of the screen.
If your view window area is less than your frame size, you can click and drag on the live video to move the camera view around. Refer to "Video Stream" on page 45.
Setup Clicking this will take you to the camera conguration pages.
If your view window area is less than your frame size, you can use
Control Pad
Edit Toolbar
Window Size
the control pad to electronically pan and tilt. Click on the arrows to move the view in that direction. Click the center to return to the home position.
Clicking this will allow you to add and remove icons from the toolbar. This lets you create a custom toolbar with only the options you want.
You can choose between various screen sizes for your camera's video:
Auto Screen: Automatically resize the camera video to
match your browser window
 Full Screen: View your camera video using the entire screen  100% Screen: View your camera's video at 100% size  50% Screen: View your camera's video at 50% size  25% Screen: View your camera's video at 25% size
Video Prole 1/2
Take a Snapshot
Record a Video Clip
Select a video prole to use. For more on setting up your video proles, refer to "Video Stream" on page 45.
This will save a snapshot to your PC using the storage folder you have selected.
This will start recording a video clip to your PC using the storage folder you have selected. Click it again to stop recording. If you close the browser window, the recording will stop.
25D-Link DCS-4605EV User Manual
Section 3: Conguration
Patrol
Auto Pan
Set a Storage Folder
Global View
Zoom In/Out
You can nd these icons in the top-right corner of the Live Video screen:
Alarm
Record Status This will turn red when the camera is recording.
After creating a list of preset ePTZ camera positions, click this to automatically cycle through the preset sequence.
Click this to start automatically panning the currently selected view.
Select a storage folder to save snapshots and video clips to.
This will show a thumbnail of your camera's full view. This can be useful when you are zooming in on the video in the Live Video screen.
Click this and use the slider to zoom in and out of your camera's video.
This will ash red when motion is detected or a DI signal is received.
Help
Logout Click this to log out of the web interface.
Click this to open a window that describes the Live Video controls.
26D-Link DCS-4605EV User Manual
Section 3: Conguration

Setup Wizard

This page lets your use setup wizards to walk you through setting up your camera's network and motion detection settings.
Network Setup
Wizard:
Motion
Detection
Setup Wizard:
Click on this button to start the Network Setup Wizard. Refer to "Network Setup Wizard" on page 28.
Click on this button to start the Motion Detection Setup Wizard. Refer to "Motion Detection Setup Wizard" on page 30.
27D-Link DCS-4605EV User Manual
Section 3: Conguration

Network Setup Wizard

This wizard will guide you through a step-by-step process to congure your camera and connect it to the Internet. Click Next to continue.
Step 1:
Select how the camera will connect to the Internet.
If your camera is connected to a router, or you are unsure how your camera will connect to
the Internet, select DHCP.
Select Static IP Client if your Internet Service Provider has provided you with connection
settings, or if you wish to set a static address within your home network. Enter the correct conguration information and click Next to continue.
If you are using PPPoE, select PPPoE and enter your user name and password.
Click Next to continue.
28D-Link DCS-4605EV User Manual
Loading...
+ 65 hidden pages