DENON AVR/AVC control protocol
Application model : AVR-5308CI/AVC-A1HD
AMX Rev Version : AVR-5308CI: Ver.5.8.0 ,AVC-A1HD: Ver.5.9.0
Application terminal : RS-232C/ Ethernet
Connector specification
1. RS-232C
Connector type: DB-9pin female type, slave straight connection (DCE type)
( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC )
Communication format:
Synchronous system : Tone step synchronization
Communication system : A half duplex
Communication speed : 9600bps
Character length : 8 bits
Parity control : None
Start bit : 1 bit
Stop bit : 1 bit
Communication procedure : Non procedural
Communication data length : 135 bytes (maximum)
07 January 2008
Page 1/51
2. Ethernet
Connector type ： RJ-45(10BASE-T/100BASE-TX)
PC
Ethernet
Cross cable
Example #1
Communication system : A half duplex
Communication speed : 10Mbps/100Mbps
Communication port : TCP port 23 (telnet)
Communication data length : 135bytes (maximum)
Example #2
Communication format ：
PC
Ethernet
Straight
cable
HUB
Ethernet
Straight
cable
07 January 2008
AVR/AVC
AVR/AVC
Page 2/51
NETWORK SETUP of AVR-5308/AVC-A1HD
>Procedure of Network Setup mode.
(1)Press SYSTEM SETUP button, then System Setup Menu appears on FL-display(and GUI)
(2)Select “Network Setup > Detail” .
(3)Set parameters described below.
<DHCP> "ON"---Use this setting when DHCP server is on the local network.
"OFF"---Use this setting when DHCP server is not on the local network.
<IP Address> When <DHCP> sets "OFF”, please set IP address.
When <DHCP> sets "ON”, you can confirm the IP address that is set by server.
<Subnet Mask> When <DHCP> sets "OFF”, please set Subnet Mask.
When <DHCP> sets "ON”, you can confirm the Subnet Mask that is set by server.
<Gateway> Set the address of Gateway when Gateway is on the local network.
Do not set this parameter when Gateway is not on the local network.
<Primary DNS> Do not set this parameter.
<Second DNS> Do not set this parameter.
<Proxy> Set this parameter "OFF".
<Network Option: Standby Mode Power Saving>
(1)Press MENU button, then Menu appears on FL-display (and GUI)
(2)Select “Manual Setup > Network Setup > Other > Power Saving”
(3)Set parameters described below.
“OFF”---Use this setting when using the AVR-5308 connected in a network.
“ON”--- Use this setting when not using the AVR-5308 connected in a network.
This setting is reducing the power consumption in the standby mode.
07 January 2008
Page 3/51
07 January 2008
Protocol specification
The following three data forms are defined.
COMMAND : The message sent to a system(AVR/AVC) from a controller(Touch Panel etc.)
A command to a system is given from a controller.
EVENT : The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC)
The result is sent, when a system is operated directly and a state changes.
*The form of EVENT presupposes that it is the same as that of COMMAND.
**Refer to the following table for the contents of COMMAND and EVENT.
RESPONSE : The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC)
if the ‘request command’ (COMMAND+?+CR(0x0D)) has came from a controller.
The RESPONSE should be sent within 200ms
*The form of RESPONSE presupposes that it is the same as that of EVENT.
Basic specification : The command by ASCII CODE, parameter expression
*ASCII CODE which can be used is from 0x20 to 0x7F : the alphabet and the number of 0-9 , and space (0x20) , Some signs ,
AND carriage return(0x0D)--- It is used only as a pause sign.
Command structure : COMMAND + PARAMETER + CR(0x0D)
COMMAND : ASCII CODE of 2 characters
ex. SI : Select Input source
MS : surround Mode Setting
MV : Master Volume setting
PW : system PoWer setting
PARAMETER : ASCII CODE ( up to 25 characters)
e x. DVD : function name
CDR/TAPE : function name
THX SURROUND EX : surround mode name
SUPER STADIUM : surround mode name
*Special Parameter--- ? : for request command
of receiving the COMMAND.
Page 4/51
The example of a command * <CR> is the meaning of 0x0D.
SIDVD<CR> : Select Input source DVD
MSSTEREO<CR> : surround Mode Set to STEREO
MVUP<CR> : Master Volume UP
PWON<CR> : system Power ON
PWSTANDBY<CR> : system Power STANDBY
SI?<CR> : Request command for now playing input source >> Return RESPONSE ‘SI***<CR>’
07 January 2008
Page 5/51
07 January 2008
Others
A) COMMAND is receivable also during transmission of EVENT.
B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels
returns as EVENT.
C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case,
the data of an intact channel is set to "50".
D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (and also the value of the channel
volume of all channels , It described in B) ) returns as EVENT.
E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME
does NOT return.
F) Although EVENT of SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return.
G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned.
H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to
the another request commands(ex. SV command).
I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME defines “99”.
J) If the MASTER VOLUME & CHANNEL VOLUME set with 0.5dB step, the PARAMETER (with COMMAND and RESPONSE, EVENT) defines three
ASCII characters as bellows.
ex. MASTER VOLUME = +1.0dB : MV81<CR>
+0.5dB : MV805<CR>
0dB : MV80<CR>
-0.5dB : MV795<CR>
-1.0dB : MV79<CR>
| |
-79.5dB : MV005<CR>
-80.0dB : MV00<CR>
--- : MV99<CR>
* At the **.0dB step, only uses two ASCII characters as
K) Four seconds later, please transmit the next COMMAND after transmitting a power on COMMAND（PWON）.
PARAMETER, same as usual.
Page 6/51
COMMAND and PARAMETER list
PW ON POWER ON/STANDBY change PWON<CR>
STANDBY PWSTANDBY<CR>
? Request PW Status PW?<CR>
MV UP MASTER VOLUME UP/DOWN, direct change to ***dB MVUP<CR>
DOWN MVDOWN<CR>
** **:00 to 99 by ASCII, 80=0dB, 99=---(MIN) MV80<CR>
? Request MV Status MV?<CR>
CV FL UP CHANNEL VOLUME UP/DOWN, direct change to ***dB CVFL UP<CR>
FL DOWN ---FRONT Lch CVFL DOWN<CR>
FL ** **:38 to 62 by ASCII, 50=0dB CVFL 50<CR>
FR UP CVFR UP<CR>
FR DOWN ---FRONT Rch CVFR DOWN<CR>
FR ** **:38 to 62 by ASCII, 50=0dB CVFR 50<CR>
C UP CVC UP<CR>
C DOWN ---CENTER ch CVC DOWN<CR>
C ** **:38 to 62 by ASCII, 50=0dB CVC 50<CR>
SL UP CVSL UP<CR>
SL DOWN ---SURROUND Lch CVSL DOWN<CR>
SL ** **:38 to 62 by ASCII, 50=0dB CVSL 50<CR>
COMMAND PARAMETER
SW1 UP
SW1 DOWN
SW1 **
SW2 UP
SW2 DOWN
SW2 **
SW3 UP
SW3 DOWN
SW3 **
MV , CV COMMAND : "*" parameter uses two or three ASCII characters. (see page6 (J) section)
---SW(When “1SP” setting),
SW Left(When “2SP L/R” or “3SP L/R/LFE setting),
SW1(When “2SP MIX” or “3SP MIX” setting)
**:00,38 to 62 by ASCII, 50=0dB, 00=OFF
---SW Right(When “2SP L/R” or “3SP L/R/LFE setting),
SW2(When “2SP MIX” or “3SP MIX” setting)
**:00,38 to 62 by ASCII, 50=0dB, 00=OFF
---LFE(When “3SP L/R/LFE setting),
SW3(When “3SP MIX” setting)
**:00,38 to 62 by ASCII, 50=0dB, 00=OFF
function example
CVSW1 UP<CR>
CVSW1 DOWN<CR>
CVSW1 50<CR>
CVSW2 UP<CR>
CVSW2 DOWN<CR>
CVSW2 50<CR>
CVSW3 UP<CR>
CVSW3 DOWN<CR>
CVSW3 50<CR>
07 January 2008
Page 7/51
07 January 2008
CV SR UP CVSRB UP<CR>
SR DOWN ---SURROUND Rch CVSRB DOWN<CR>
SR ** **:38 to 62 by ASCII, 50=0dB CVSRB 50<CR>
SBL UP CVSBL UP<CR>
SBL DOWN ---SURROUND BACK Lch (SBch 2SP) CVSBL DOWN<CR>
SBL ** **:38 to 62 by ASCII, 50=0dB CVSBL 50<CR>
SBR UP CVSBR UP<CR>
SBR DOWN ---SURROUND BACK Rch (SBch 2SP) CVSBR DOWN<CR>
SBR ** **:38 to 62 by ASCII, 50=0dB CVSBR 50<CR>
SB UP CVSBL UP<CR>
SB DOWN ---SURROUND BACKch (SBch 1SP) CVSBL DOWN<CR>
SB ** **:38 to 62 by ASCII, 50=0dB CVSBL 50<CR>
? Request CV Status CV?<CR>
MU ON OUTPUT MUTE ON/OFF change MUON<CR>
OFF MUOFF<CR>
? Request MU Status MU?<CR>
COMMAND PARAMETER
CV TR UP
TR DOWN
TR **
TR?
CV COMMAND : "*" parameter uses two or three ASCII characters. (see page6 (J) section)
---TRANSDUCER LEVEL UP/DOWN, direct change to **dB
**:00,38 to 62 by ASCII, 50=0dB, 00=OFF
Request CVTR Status
function example
CVTR UP<CR>
CVTR DOWN<CR>
CVTR 50<CR>
CVTR?<CR>
Page 8/51
07 January 2008
SI PHONO Select INPUT source SIPHONO<CR>
CD SICD<CR>
TUNER SITUNER<CR>
DVD SIDVD<CR>
V.AUX SIV.AUX<CR>
? Request SI Status SI?<CR>
ZM ON MAIN-ZONE ON/OFF change ZMON<CR>
OFF ZMOFF<CR>
? Request ZM Status ZM?<CR>
COMMAND PARAMETER
HDP SIHDP<CR>
TV/CBL SITV/CBL<CR>
SAT SISAT<CR>
VCR SIVCR<CR>
DVR-1 SIDVR-1<CR>
DVR-2 SIDVR-2<CR>
NET/USB SINET/USB<CR>
XM (North America model Only) SIXM<CR>
HDRADIO (North America model Only) SIHDRADIO<CR>
IPOD SIIPOD<CR>
SR PHONO REC SELECT mode set, and select source SRPHONO<CR>
| ---The name of PARAMETER is |
IPOD the same as that of the time of SI COMMAND. SRIPOD<CR>
SOURCE REC SELECT mode cancel SRSOURCE<CR>
? Return SR Status SR?<CR>
SD AUTO set AUTO mode (Priority:HDMI>>DIGITAL>>ANALOG) SDAUTO<CR>
HDMI set force HDMI INPUT mode SDHDMI<CR>
DIGITAL set force DIGITAL INPUT (Optical, Coaxial, BNC)mode SDDIGITAL<CR>
ANALOG set force ANALOG INPUT mode SDANALOG<CR>
EXT.IN-1 ---Set EXT.IN mode at AVR-5308 SDEXT.IN-1<CR>
? Return SD Status SD?<CR>
DC AUTO set DIGITAL INPUT AUTO mode DCAUTO<CR>
PCM set DIGITAL INPUT force PCM mode DCPCM<CR>
DTS set DIGITAL INPUT force DTS mode DCDTS<CR>
? Return DC Status DC?
function example
Page 9/51
07 January 2008
MS DIRECT SURROUND mode set MSDIRECT<CR>
PURE DIRECT MSPURE DIRECT<CR>
STEREO MSSTEREO<CR>
STANDARD MSSTANDARD<CR>
DOLBY DIGITAL MSDOLBY DIGITAL<CR>
DTS SURROUND MSDTS SURROUND<CR>
NEURAL (North America model only) MSNEURAL<CR>
WIDE SCREEN MSWIDE SCREEN
7CH STEREO MS7CH STEREO<CR>
SUPER STADIUM MSSUPER STADIUM<CR>
ROCK ARENA MSROCK ARENA<CR>
JAZZ CLUB MSJAZZ CLUB<CR>
CLASSIC CONCERT MSCLASSIC CONCERT<CR>
MONO MOVIE MSMONO MOVIE<CR>
MATRIX MSMATRIX<CR>
VIDEO GAME MSVIDEO GAME<CR>
? Return MS Status MS?<CR>
COMMAND PARAMETER
SV DVD VIDEO SELECT mode set, and select source SVDVD<CR>
V.AUX SVV.AUX<CR>
SOURCE VIDEO SELECT mode cancel SVSOURCE<CR>
? Request SV Status SV?<CR>
HDP
TV/CBL
SAT
VCR
DVR-1
DVR-2
DOLBY H/P
HOME THX CINEMA
SVHDP<CR>
SVTV/CBL<CR>
SVSAT<CR>
SVVCR<CR>
SVDVR-1<CR>
SVDVR-2<CR>
Function example
MSDOLBY H/P<CR>
MSHOME THX CINEMA<CR>
Page 10/51
MS QUICK1 QUICK SELECT 1-3 MODE SELECT MSQUICK1<CR>
QUICK2 MSQUICK2<CR>
QUICK3 MSQUICK3<CR>
QUICK1 MEMORY QUICK SELECT 1-3 MODE MEMORY MSQUICK1 MEMORY<CR>
QUICK2 MEMORY MSQUICK2 MEMORY<CR>
QUICK3 MEMORY MSQUICK3 MEMORY<CR>
QUICK ? Return MSQUICK Status MSQUICK ?<CR>
VS MONIAUTO Set HDMI MONITOR automatic detection VSMONIAUTO<CR>
MONI1 Set HDMI MONITOR OUT-1 VSMONI1<CR>
MONI2 Set HDMI MONITOR OUT-2 VSMONI2<CR>
MONI? Return VSMONITOR Status VSMONI?<CR>
ASPNRM Set Normal mode VSASPNRM<CR>
ASPFUL Set FULL mode VSASPFUL<CR>
ASP? Return VSASPECT Status VSASP?<CR>
SC48P Set Resolution to 480p/576p VSSC48P<CR>
SC10I Set Resolution to 1080i VSSC10I<CR>
SC72P Set Resolution to 720p VSSC72P<CR>
SC10P Set Resolution to 1080p VSSC10P<CR>
SCAUTO Set Resolution to AUTO VSSCAUTO<CR>
SC? Return VSSCALE Status VSSC?<CR>
COMMAND PARAMETER
SCH48P Set Resolution to 480p/576p (HDMI) VSSC48P<CR>
SCH10I Set Resolution to 1080i(HDMI) VSSC10I<CR>
SCH72P Set Resolution to 720p(HDMI) VSSC72P<CR>
SCH10P Set Resolution to 1080p(HDMI) VSSC10P<CR>
SCHAUTO Set Resolution to AUTO(HDMI) VSSCAUTO<CR>
SCH? Return VSSCALE Status(HDMI) VSSCH?<CR>
function example
07 January 2008
Page 11/51
07 January 2008
PS TONE DEFEAT ON PARAMETER setting TONE DEFEAT ON/OFF PSTONE DEFEAT ON<CR>
TONE DEFEAT OFF PSTONE DEFEAT OFF<CR>
TONE DEFEAT ? Request PSTONE DEFEAT Status PSTONE DEFEAT ?<CR>
BAS UP ALLch BASS UP/DOWN, direct change to **dB PSBAS UP<CR>
BAS DOWN **:00 to 99 by ASCII, 50=0dB PSBAS DOWN<CR>
BAS ** ---AVR-5308 can be operated from -6 to +6(44 to 56) PSBAS 50<CR>
TRE UP ALLch TREBLE UP/DOWN, direct change to **dB PSTRE UP<CR>
TRE DOWN **:00 to 99 by ASCII, 50=0dB PSTRE DOWN<CR>
TRE ** ---AVR-5308 can be operated from -6 to +6(44 to 56) PSTRE 50<CR>
COMMAND PARAMETER
BASFRO UP FRONTch BASS UP/DOWN, direct change to **dB PSBASFRO UP<CR>
BASFRO DOWN **:00 to 99 by ASCII, 50=0dB PSBASFRO DOWN<CR>
BASFRO ** ---AVR-5308 can be operated from -6 to +6(44 to 56) PSBASFRO 50<CR>
BASCEN UP CENTERch BASS UP/DOWN, direct change to **dB PSBASCEN UP<CR>
BASCEN DOWN **:00 to 99 by ASCII, 50=0dB PSBASCEN DOWN<CR>
BASCEN ** ---AVR-5308 can be operated from -6 to +6(44 to 56) PSBASCEN 50<CR>
BASSUR UP SURROUNDch BASS UP/DOWN, direct change to **dB PSBASSUR UP<CR>
BASSUR DOWN **:00 to 99 by ASCII, 50=0dB PSBASSUR DOWN<CR>
BASSUR ** ---AVR-5308 can be operated from -6 to +6(44 to 56) PSBASSUR 50<CR>
BASSBK UP SURROUND BACKch BASS UP/DOWN, direct change to **dB PSBASSBK UP<CR>
BASSBK DOWN **:00 to 99 by ASCII, 50=0dB PSBASSBK DOWN<CR>
BASSBK ** ---AVR-5308 can be operated from -6 to +6(44 to 56) PSBASSBK 50<CR>
BASSWF UP SUBWOOFERch BASS UP/DOWN, direct change to **dB PSBASSWF UP<CR>
BASSWF DOWN **:00 to 99 by ASCII, 50=0dB PSBASSWF DOWN<CR>
BASSWF ** ---AVR-5308 can be operated from -6 to +6(44 to 56) PSBASSWF 50<CR>
BAS ? Return PSBAS Status PSBAS ?<CR>
TREFRO UP FRONTch TRE UP/DOWN, direct change to **dB PSTREFRO UP<CR>
TREFRO DOWN **:00 to 99 by ASCII, 50=0dB PSTREFRO DOWN<CR>
TREFRO ** ---AVR-5308 can be operated from -6 to +6(44 to 56) PSTREFRO 50<CR>
TRECEN UP CENTERch TRE UP/DOWN, direct change to **dB PSTRECEN UP<CR>
TRECEN DOWN **:00 to 99 by ASCII, 50=0dB PSTRECEN DOWN<CR>
TRECEN ** ---AVR-5308 can be operated from -6 to +6(44 to 56) PSTRECEN 50<CR>
PS COMMAND : "*" parameter uses two ASCII characters. (see page 6 J) section)
function example
Page 12/51
07 January 2008
PS
TRE ? Return PSTRE Status PSTRE ?<CR>
ROOM EQ:AUDYSSEY ROOM EQ mode direct change PSROOM EQ:AUDYSSEY<CR>
ROOM EQ:BYP.LR PSROOM EQ:BYP.LR<CR>
NIGHT OFF NIGHT MODE direct change PSNIGHT OFF<CR>
NIGHT LOW PSNIGHT LOW<CR>
NIGHT MID PSNIGHT MID<CR>
NIGHT HI PSNIGHT HI<CR>
NIGHT ? Return PSNIGHT Status PSNIGHT ?<CR>
RSTR OFF AUDIO RESTORER direct change PSRSTR OFF<CR>
RSTR MODE1 PSRSTR MODE1<CR>
RSTR MODE2 PSRSTR MODE2<CR>
RSTR MODE3 PSRSTR MODE3<CR>
RSTR ? Return PSRSTR Status PSRSTR ?<CR>
DELAY UP AUDIO DELAY UP/DOWN, direct change to ***dB PSDELAY UP<CR>
DELAY DOWN ***:000 to 999 by ASCII, 000=0ms, 200=200ms PSDELAY DOWN<CR>
DELAY *** ---AVR-5308 can be operated from 0 to 200 PSDELAY 200<CR>
COMMAND PARAMETER
TRESUR UP SURROUNDch TRE UP/DOWN, direct change to **dB PSTRESUR UP<CR>
TRESUR DOWN **:00 to 99 by ASCII, 50=0dB PSTRESUR DOWN<CR>
TRESUR ** ---AVR-5308 can be operated from -6 to +6(44 to 56) PSTRESUR 50<CR>
TRESBK UP SURROUND BACKch TRE UP/DOWN, direct change to **dB PSTRESBK UP<CR>
TRESBK DOWN **:00 to 99 by ASCII, 50=0dB PSTRESBK DOWN<CR>
TRESBK ** ---AVR-5308 can be operated from -6 to +6(44 to 56) PSTRESBK 50<CR>
ROOM EQ:FLAT PSROOM EQ:FLAT<CR>
ROOM EQ:MANUAL PSROOM EQ:MANUAL<CR>
ROOM EQ:OFF PSROOM EQ:OFF<CR>
ROOM EQ: ? Request PSROOM EQ: Status PSROOM EQ: ?<CR>
DYE ON DYNAMIC EQ ON/OFF direct change PSDYE ON<CR>
DYE OFF PSDYE OFF<CR>
DYE ? PSDYE ?<CR>
PS COMMAND : "*" parameter uses two or three ASCII characters. (see page 6 J) section)
function example
Page 13/51
07 January 2008
PS SB:MTRX ON
SB:NON MTRX PSSB:NON MTRX<CR>
SB:PL2X CINEMA PSSB:PL2X CINEMA<CR>
SB:PL2X MUSIC PSSB:PL2X MUSIC<CR>
SB:ON PSSB:ON<CR>
SB:OFF PSSB:OFF<CR>
SB: ? Request PSSB: Status PSSB: ?<CR>
CINEMA EQ.ON CINEMA EQ. ON/OFF PSCINEMA EQ.ON<CR>
CINEMA EQ.OFF PSCINEMA EQ.OFF<CR>
CINEMA EQ. ? Request PSCINEMA EQ. Status PSCINEMA EQ. ?<CR>
MODE:MUSIC CINEMA / MUSIC / GAME / PL mode change PSMODE:MUSIC<CR>
MODE:CINEMA (This parameter can change DOLBY PL2,PL2x,NEO:6 mode.) PSMODE:CINEMA<CR>
MODE:GAME
MODE:PRO LOGIC --- GAME can change DOLBY PL2 & PL2x mode PSMODE:PRO LOGIC<CR>
--- PL can change ONLY DOLBY PL2 mode
MODE: ? Request PSMODE: Status PSMODE: ?<CR>
COMMAND PARAMETER
SB:7.1+THX PSSB:7.1+THX<CR>
SB:ULTRA2 C PSSB:ULTRA2 C<CR>
SB:SURR EX PSSB:SURR EX<CR>
SB:MUSIC PSSB:MUSIC<CR>
SB:GAME PSSB:GAME<CR>
DEC:PL2X C DECODER change PSDEC:PL2X C<CR>
DEC:PL2 C (This parameter can change THX mode.) PSDEC:PL2 C<CR>
DEC:PL PSDEC:PL<CR>
DEC:NEO:6 C PSDEC:NEO:6 C<CR>
DEC: ? Request PSDEC: Status PSDEC: ?<CR>
DEH:PL2 C DECODER change PSDEH:PL2 C<CR>
DEH:PL2 M (This parameter can change DOLBY HEADPHONE mode.) PSDEH:PL2 M<CR>
DEH:NEO:6 C PSDEH:NEO:6 C<CR>
DEH:NEO:6 M PSDEH:NEO:6 M<CR>
DEH:OFF PSDEH:OFF<CR>
DEH: ? Request PSDEC: Status PSDEH: ?<CR>
function example
SURROUND BACK SP MODE set / THX MODE set
---SB=ON：PL2x mode / SB=OFF：PL2 mode
PSSB:MTRX ON<CR>
PSMODE:GAME<CR>
Page 14/51
PS
DCO OFF D.COMP direct change PSDCO OFF<CR>
DCO LOW PSDCO LOW<CR>
DCO MID PSDCO MID<CR>
DCO HIGH PSDCO HIGH<CR>
DCO ? Return PSDCO Status PSDCO ?<CR>
LFE UP LFE UP/DOWN, direct change to **dB PSLEE UP<CR>
LFE DOWN **:00 to 99 by ASCII, 00=0dB, 10=-10dB PSLFE DOWN<CR>
LFE ** ---AVR-5308 can be operated from 0 to -10 PSLFE 10<CR>
LFE ? Return PSLFE Status PSLFE ? <CR>
EFF ON EFFECT ON/OFF, EFFECT LEVEL direct change to **dB PSEFF UP<CR>
EFF OFF **:00 to 99 by ASCII, 00=0dB, 10=10dB PSEFF DOWN<CR>
EFF ** ---AVR-5308 can be operated from 1 to 15 PSEFF **<CR>
EFF ? Return PSEFF Status PSEFF ?<CR>
DEL UP DELAY UP/DOWN, direct change to ***dB PSDEL UP<CR>
DEL DOWN ***:000 to 999 by ASCII, 000=0ms, 300=300ms PSDEL DOWN<CR>
DEL *** ---AVR-5308 can be operated from 0 to 300 PSDEL ***<CR>
DEL ? Return PSDEL Status PSDEL ?<CR>
AFD ON AFDM ON/OFF PSAFD ON<CR>
AFD OFF PSAFD OFF<CR>
AFD ? Return PSAFD Status PSAFD ?<CR>
PAN ON PANORAMA ON/OFF PSPAN ON<CR>
PAN OFF PSPAN OFF<CR>
PAN ? Return PSPAN Status PSPAN ?<CR>
DIM UP DIMENSION UP/DOWN, direct change to **dB PSDIM UP<CR>
DIM DOWN **:00 to 99 by ASCII, 00=0, PSDIM DOWN<CR>
DIM ** ---AVR-5308 can be operated from 0 to 6 PSDIM **<CR>
DIM ? Return PSDIM Status PSDIM ?<CR>
COMMAND PARAMETER
DRC AUTO DRC direct change PSDRC AUTO<CR>
DRC LOW PSDRC LOW<CR>
DRC MID PSDRC MID<CR>
DRC HI PSDRC HI<CR>
DRC OFF PSDRC OFF<CR>
DRC ? Return PSDRC Status PSDRC ?<CR>
PS COMMAND : "*" parameter uses two or three ASCII characters. (see page 6 J) section)
function example
07 January 2008
Page 15/51
PS CEN UP CENTER WIDTH UP/DOWN, direct change to **dB PSCEN UP<CR>
CEN DOWN **:00 to 99 by ASCII, 00=0 PSCEN DOWN<CR>
CEN ** ---AVR-5308 can be operated from 0 to 7 PSCEN 07<CR>
CEN ? Return PSCEN Status PSCEN ?<CR>
CEI UP CENTER IMAGE UP/DOWN, direct change to **dB PSCEI UP<CR>
CEI DOWN **:00 to 99 by ASCII, 00=0.0 PSCEI DOWN<CR>
CEI ** ---AVR-5308 can be operated from 0.0 to 1.0 PSCEI 10<CR>
CEI ? Return PSCEI Status OSCEI ?<CR>
ATT ON SW ATT ON/OFF PSATT ON<CR>
ATT OFF PSATT OFF<CR>
ATT ? Return PSATT Status PSATT ?<CR>
SWR ON SW ON/OFF PSSWR ON<CR>
SWR OFF PSSWR OFF<CR>
SWR ? Return PSSWR Status PSSWR ?<CR>
RSZ S ROOM SIZE direct change PSRSZ S<CR>
RSZ MS PSRSZ MS<CR>
RSZ M PSRSZ M<CR>
RSZ ML PSRSZ ML<CR>
RSZ L PSRSZ L<CR>
RSZ ? Return PSRSZ Status PSRSZ ?<CR>
COMMAND PARAMETER
PS COMMAND : "*" parameter uses two or three ASCII characters. (see page 6 J) section)
function example
07 January 2008
Page 16/51
Loading...