Denon AVR-3311CI Owners Manual

Simple version

Version simpliﬁée

Versión sencilla

AV SURROUND RECEIVER

AVR-3311CI

Owner’s Manual Manuel de l’Utilisateur Manual del usuario

Basic version

Advanced version

Version basique Versión básica

Version avancée

Versión avanzada

Information

“Part names and functions” (vpage100)

Informations

“Nomenclature et fonctions“ (vpage 100)

Información

“Nombres y funciones de las piezas“ (vpágina 100)

SAFETY PRECAUTIONS

IMPORTANT SAFETY

ENGLISHFRANCAISESPAÑOL

FCC INFORMATION (For US customers)

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning ﬂash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufﬁcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

HOT SURFACE. DO NOT TOUCH.

The top surface over the internal heat sink may become hot when operating this product continuously.

Hot

surface

mark

Do not touch hot areas, especially around the “Hot surface mark” and the top panel.

PRECAUTION:

SURFACE CHAUDE. NE PAS TOUCHER.

La surface supérieure du dissipateur de chaleur peut devenir chaude si vous utilisez ce produit en continu. Ne touchez pas les zones chaudes, tout particulièrement vers l’inscription “Hot surface mark” et le panneau supérieur.

PRECAUCIÓN:

SUPERFICIE CALIENTE. NO TOCAR.

La superﬁcie superior sobre el disipador de calor interno podría llegar a calentarse al operar este producto de forma continua. No toque las áreas calientes, especialmente las situadas alrededor de la “Hot surface mark” y del panel superior.

INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Batteries shall not be exposed to excessive heat such as sunshine, ﬁre or the like.

CAUTION:

To completely disconnect this product from the mains, disconnect the plug from the wall socket outlet. The mains plug is used to completely interrupt the power supply to the unit and must be within easy access by the user.

PRECAUTION:

Pour déconnecter complètement ce produit du courant secteur, débranchez la prise de la prise murale. La prise secteur est utilisée pour couper complètement l’alimentation de l’appareil et l’utilisateur doit pouvoir y accéder facilement.

PRECAUCIÓN:

Para desconectar completamente este producto de la alimentación eléctrica, desconecte el enchufe del enchufe de la pared. El enchufe de la alimentación eléctrica se utiliza para interrumpir por completo el suministro de alimentación eléctrica a la unidad y debe de encontrarse en un lugar al que el usuario tenga fácil acceso.

1. COMPLIANCE INFORMATION

Product Name: AV Surround Receiver Model Number: AVR-3311CI This product complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received,

including interference that may cause undesired operation. Denon Electronics (USA), LLC (a D & M Holdings Company) 100 Corporate Drive Mahwah, NJ 07430-2041 Tel. (800) 497-8921

2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT

This product, when installed as indicated in the instructions contained

in this manual, meets FCC requirements. Modiﬁcation not expressly

approved by DENON may void your authority, granted by the FCC, to use

the product.

3. IMPORTANT

When connecting this product to network hub or router, use only shielded

STP or FTP LAN cables which is available at retailer. Follow all installation instructions. Failure to follow instructions could void

your authority, granted by the FCC, to use the product.

4. NOTE

This product has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This product generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

product does cause harmful interference to radio or television reception,

which can be determined by turning the product OFF and ON, the user

is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the product into an outlet on a circuit different from that to which the receiver is connected.

• Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for help.

For Canadian customers:

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

ESPAÑOLENGLISH FRANCAIS

NOTES ON USE / OBSERVATIONS RELATIVES A L’UTILISATION / NOTAS SOBRE EL USO

WARNINGS AVERTISSEMENTS ADVERTENCIAS

• Avoid high temperatures. Allow for sufﬁcient heat dispersion when installed in a rack.

• Handle the power cord carefully. Hold the plug when unplugging the cord.

• Keep the unit free from moisture, water, and dust.

• Unplug the power cord when not using the unit for long periods of time.

• Do not obstruct the ventilation holes.

• Do not let foreign objects into the unit.

• Do not let insecticides, benzene, and thinner come in contact with the unit.

• Never disassemble or modify the unit in any way.

• Ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, tablecloths or curtains.

• Naked ﬂame sources such as lighted candles should not be placed on the unit.

• Observe and follow local regulations regarding battery disposal.

• Do not expose the unit to dripping or splashing ﬂuids.

• Do not place objects ﬁlled with liquids, such as vases, on the unit.

• Do not handle the mains cord with wet hands.

• When the switch is in the OFF position, the equipment is not completely switched off from MAINS.

• The equipment shall be installed near the power supply so that the power supply is easily accessible.

• Eviter des températures élevées. Tenir compte d’une dispersion de chaleur sufﬁsante lors de l’installation sur une étagère.

• Manipuler le cordon d’alimentation avec précaution. Tenir la prise lors du débranchement du cordon.

• Protéger l’appareil contre l’humidité, l’eau et la poussière.

• Débrancher le cordon d’alimentation lorsque l’appareil n’est pas utilisé pendant de longues périodes.

• Ne pas obstruer les trous d’aération.

• Ne pas laisser des objets étrangers dans l’appareil.

• Ne pas mettre en contact des insecticides, du benzène et un diluant avec l’appareil.

• Ne jamais démonter ou modiﬁer l’appareil d’une manière ou d’une autre.

• Ne pas recouvrir les oriﬁces de ventilation avec des objets tels que des journaux, nappes ou rideaux. Cela entraverait la ventilation.

• Ne jamais placer de ﬂamme nue sur l’appareil, notamment des bougies allumées.

• Veillez à respecter les lois en vigueur lorsque vous jetez les piles usagées.

• L’appareil ne doit pas être exposé à l’eau ou à l’humidité.

• Ne pas poser d’objet contenant du liquide, par exemple un vase, sur l’appareil.

• Ne pas manipuler le cordon d’alimentation avec les mains mouillées.

• Lorsque l’interrupteur est sur la position OFF, l’appareil n’est pas complètement déconnecté du SECTEUR (MAINS).

• L’appareil sera installé près de la source d’alimentation, de sorte que cette dernière soit facilement accessible.

• Evite altas temperaturas. Permite la suﬁciente dispersión del calor cuando está instalado en la consola.

• Maneje el cordón de energía con cuidado. Sostenga el enchufe cuando desconecte el cordón de energía.

• Mantenga el equipo libre de humedad, agua y polvo.

• Desconecte el cordón de energía cuando no utilice el equipo por mucho tiempo.

• No obstruya los oriﬁcios de ventilación.

• No deje objetos extraños dentro del equipo.

• No permita el contacto de insecticidas, gasolina y diluyentes con el equipo.

• Nunca desarme o modiﬁque el equipo de ninguna manera.

• La ventilación no debe quedar obstruida por haberse cubierto las aperturas con objetos como periódicos, manteles o cortinas.

• No deberán colocarse sobre el aparato fuentes inﬂamables sin protección, como velas encendidas.

• A la hora de deshacerse de las pilas, respete la normativa para el cuidado del medio ambiente.

• No exponer el aparato al goteo o salpicaduras cuando se utilice.

• No colocar sobre el aparato objetos llenos de líquido, como jarros.

• No maneje el cable de alimentación con las manos mojadas.

• Cuando el interruptor está en la posición OFF, el equipo no está completamente desconectado de la alimentación MAINS.

• El equipo se instalará cerca de la fuente de alimentación de manera que resulte fácil acceder a ella.

n CAUTIONS ON INSTALLATION PRÉCAUTIONS D’INSTALLATION EMPLAZAMIENTO DE LA INSTALACIÓN

z z

Wall Paroi Pared

zFor proper heat dispersal, do not install this unit in a conﬁned

space, such as a bookcase or similar enclosure.

• More than 0.3 m (12 in.) is recommended.

• Do not place any other equipment on this unit.

zPour permettre la dissipation de chaleur requise, n’installez

pas cette unité dans un espace conﬁné tel qu’une bibliothèque ou un endroit similaire.

• Une distance de plus de 0.3 m (12 po) est recommandée.

• Ne placez aucun matériel sur cet appareil.

zPara la dispersión del calor adecuadamente, no instale este

equipo en un lugar conﬁnado tal como una librería o unidad similar.

• Se recomienda dejar más de 0.3 m (12 pulg.) alrededor.

• No coloque ningún otro equipo sobre la unidad.

Getting started

ENGLISH

Thank you for purchasing this DENON product. To ensure proper operation, please read these owner’s manual carefully before using the product. After reading them, be sure to keep them for future reference.

Contents

Getting started ·············································································· 1

Accessories ··················································································1 About this manual ·········································································1 Features ························································································2 Cautions on handling ····································································2

Simple version (Simple setup guide) ··························3

Basic version ··········································································12

Connections ·················································································13

Important information ································································· 13 Connecting an HDMI-compatible device ····································14 Connecting a TV··········································································16 Connecting a Blu-ray Disc player ················································16 Connecting a DVD player ····························································17 Connecting a set-top box (Satellite tuner/cable TV) ···················· 17 Connecting a digital video recorder ············································18 Connecting a digital camcorder ··················································18 Connecting a control dock for iPod ·············································19 Connecting an iPod or USB memory device to the USB port ·····19 Connecting an antenna ······························································· 20 Connecting a record player ························································· 21 Connecting a CD player ······························································21 Connecting to a home network (LAN) ········································22 Connecting a external power ampliﬁer ······································· 23 Connecting an external control device ········································23

Playback (Basic operation) ························································· 24

Important information ································································· 24 Playing a Blu-ray Disc player/DVD player ···································· 25 Playing a CD player ····································································· 25 Playing an iPod® ·········································································25 Tuning in radio stations ·······························································28 Playing a network audio ······························································32 Playing a USB memory device ····················································43

Selecting a listening mode (Surround mode) ··························45

Standard playback ·······································································45 DENON original surround playback ·············································47 Stereo playback ··········································································47 Direct playback ···········································································47 Pure direct playback····································································47

Advanced version ·······························································48

Speaker installation/connection (Other than 5.1-channel) ····· 49

Install ··························································································49 Connect ······················································································50 Set up speakers ·········································································· 52

Playback (Advanced operation) ················································· 54

Convenient functions ··································································54

Playback in ZONE2/ZONE3 (Separate room) ··························61

Audio output ···············································································61 Video output ···············································································61 Playback ······················································································62 Quick select function ·································································· 62

How to make detailed settings ··················································63

Menu map ··················································································63 Examples of menu and front display ··········································64 Inputting characters ··································································· 65 Input Setup ·················································································67 Audio/Video Adjust ·····································································73 Manual Setup··············································································79 Information ·················································································90

Operating the connected devices by remote control unit ······91

Operating the main remote control unit ·····································91 Operating the sub remote control unit ·······································95

Information ·············································································99

Part names and functions·························································100

Front panel ················································································100 Display ······················································································101 Rear panel ·················································································102 Remote control unit ·································································· 103

Other information ·····································································105

Trademark information ······························································105 Surround ···················································································106 Relationship between video signals and monitor output ··········110 Explanation of terms ·································································111

Troubleshooting ········································································113

Resetting the microprocessor ··················································116

Speciﬁcations ············································································117

Accessories

Check that the following parts are supplied with the product.

q Owner’s manual ...................................................................... 1

w Warranty (for North America model only) ................................ 1

e Service network list ................................................................. 1

r Power cord (Cord length: Approx. 5.9 ft / 1.8 m) .................... 1

t Main remote control unit (RC-1146) ........................................ 1

y R6/AA batteries (for RC-1146) ................................................. 2

u Sub remote control unit (RC-1148) .......................................... 1

i R03/AAA batteries (for RC-1148) .............................................2

o Setup microphone

(DM-A409, Cord length: Approx. 19.7 ft / 6.0 m) .................... 1

Q0 AM loop antenna (for HD Radio broadcasts) ........................... 1

Q1 FM indoor antenna (for HD Radio broadcasts) ........................1

Q0 Q1

About this manual

n Operation buttons

The operations described in this manual are based mainly on remote control operation.

n Symbols

NOTE

n Illustrations

Note that the illustrations in these instructions are for explanation purposes and may differ from the actual unit.

This symbol indicates a reference page on which related information is described.

This symbol indicates a supplementary information and tips for operations.

Basic versionSimple version Advanced version Information

ENGLISH

Features

Fully Discrete, identical quality and power for all 7 channels (165 W x 7ch)

The unit is equipped with a power ampliﬁer that reproduces highﬁdelity sound in surround mode with equal quality and power for all channels, true to the original sound. The power ampliﬁer circuit adopts a discrete-circuit conﬁguration that achieves high-quality surround sound reproduction.

Supports HDMI 1.4 with 3D, ARC, Deep Color, x.v.Color , Auto Lipsync and HDMI control function

This unit can output 3D video signals input from a Blu-ray Disc player to a TV that supports a 3D system. This unit also supports the ARC (Audio Return Channel) function, which reproduces TV sound with this unit via an HDMI cable used for connecting the

unit and a TVz1.

z1 The TV should support the ARC function.

Internet radio, music and photo streaming via network

This unit can playback audio ﬁles and still images such as photographs that are stored on your computer via a network. You can also listen to internet radio and a whole host of other online

musicz3 that uses network technology.

z2 An internet connection is required. z3 You may be required to sign a service agreement with the

6-HDMI inputs and 2-outputs

The unit is equipped with 6 HDMI input connectors for connecting devices with HDMI connectors, such as a Blu-ray Disc player, game machine, HD video camera, etc.

companies that provide particular services.

Audyssey DSX™

This unit is equipped with an Audyssey DSX decoder. By connecting front height speakers to this unit and playing back through Audyssey DSX, you can experience a more powerful playback expression in the height audio range. By connecting front wide speakers, you can experience a more powerful playback expression in the wide audio range.

Easy to use, Graphical User Interface

This unit is equipped with an easy to see “Graphical User Interface” that uses menu displays and levels. The use of level displays increases operability of the unit.

All sources are up-scaled to 1080p

The unit is provided with an HDMI video up-scaling function that converts an analog video signal input to the unit to a 1080p (HD resolution) signal and supplies it to a TV via the HDMI connector. This enables the unit and a TV connected with a single HDMI cable and any video source to be reproduced precisely with HD level of quality.

Direct play for iPod® and iPhone® via USB

Music data from an iPod can be played back if you connect the USB cable supplied with the iPod via the USB port of this unit, and also an iPod can be controlled with the remote control unit for this unit. When an iPod is connected, merely pressing iPod PLAY on the main unit or remote control unit starts playback of music from the iPod.

Cautions on handling

• Before turning the power switch on

Check once again that all connections are correct and that there are no problems with the connection cables.

• Power is supplied to some of the circuitry even when the unit is set to the standby mode. When going on vacation or leaving home for long periods of time, be sure to unplug the power cord from the power outlet.

• About condensation If there is a major difference in temperature between the inside of the unit and the surroundings, condensation (dew) may form on the operating parts inside the unit, causing the unit not to operate properly. If this happens, let the unit sit for an hour or two with the power turned off and wait until there is little difference in temperature before using the unit.

• Cautions on using mobile phones Using a mobile phone near this unit may result in noise. If that occurs, move the mobile phone away from this unit when it is in use.

• Moving the unit Turn off the power and unplug the power cord from the power outlet. Next, disconnect the connection cables to other system units before moving the unit.

• About Care

• Wipe the cabinet and control panel clean with a soft cloth.

• Follow the instructions when using a chemical cleaner.

• Benzene, paint thinner or other organic solvents as well as

insecticide may cause material changes and discoloration if brought into contact with the unit, and should therefore not be used.

High deﬁnition audio support

The unit is equipped with a decoder which supports high-quality digital audio format for Blu-ray Disc players such as Dolby TrueHD, DTS-HD Master Audio, etc.

Simple version

Here, we explain the entire setup procedure, from unboxing the unit to using it in a home theater. The “Simple version” describes the installation, connection and setup methods for 5.1-channel speakers. See page 49 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.

n Before connecting the unit, turn off the power to all devices. n For operation of the connected devices, refer to the user manuals for each device.

Simple version (Simple setup guide)

ENGLISH

Basic version Advanced version InformationSimple version

Install

(vpage4)

Enjoy better audio, using the correct install method.

Connect

(vpage4)

Connect 5.1-channel speakers, a TV and Blu-ray Disc player equipped with an HDMI connector.

Turn on power

(vpage6)

Set up speakers

(vpage6)

Use the setup microphone (DM-A409) included with the product, for automatic setup.

Play back disc

(vpage11)

Enjoy Blu-ray Disc and DVD in surround sound.

Set up speakers (Audyssey® Auto Setup)

STEP 1

Preparation

STEP 2

Speaker Detection

STEP 3

Measurement

STEP 4

Calculation

STEP 5

Check

STEP 6

Store

Finish

ENGLISH

Install

1 2 3 4 5

This unit can perform 2.0/2.1 to 7.1-channel surround playback. Here, we explain setup using the example of 5.1-channel speaker playback.

FL FR

22 – 30˚

120˚

Listening position

Connect

Speakers

Carefully check the left (L) and right (R) channels and + (red) and – (black) polarities on the speakers being connected to the this unit, and be sure to interconnect the channels and polarities correctly.

Connecting the speaker cables

Peel off about 0.03 ft/10 mm of sheathing from the tip of the speaker cable, then either twist the core wire tightly or terminate it.

1 2 3 4 5

NOTE

• Connect so that the speaker cable core wires do not protrude from the speaker terminal. The protection circuit may be activated if the core wires touch the rear panel or if the + and – sides touch each other (vpage112 “Protection Circuit”).

• Never touch the speaker terminals while the power supply is connected. Doing so could result in electric shock.

• Use speakers with the speaker impedances shown below.

Speaker terminals

FRONT CENTER SURROUND SURR. BACK / AMP ASSIGN F.HEIGHT F.WIDE

Speaker

impedance

6 – 16 Ω

FL Front speaker (L) • Install the surround speakers in a position FR Front speaker (R) C Center speaker SW Subwoofer SL Surround speaker (L) SR Surround speaker (R)

The “Simple Version” describes the installation, connection and setup methods for 5.1-channel speakers.

2 to 3 ft (60 to 90 cm) higher than ear level.

Surround

Front speaker

speaker

2 – 3 ft / 60 – 90 cm

GViewed from the sideH

See page 49 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.

When using a banana plug

Tighten the speaker terminal ﬁrmly before inserting the banana plug.

ENGLISH

Connect

Blu-ray Disc player and TV

Use only an HDMI (High Deﬁnition Multimedia Interface) cable that bears the HDMI logo (a genuine HDMI product). Using a cable without the HDMI logo (a non-genuine HDMI product) may result in abnormal playback. When outputting Deep Color or 1080p, etc., we recommend you use a “High Speed HDMI cable” or a “High Speed HDMI cable with Ethernet”for enhanced high-quality playback.

Basic version Advanced version InformationSimple version

Audio cable (sold separately)

Subwoofer with built-in ampliﬁer

FL FR

Speaker cables

(sold separately)

Blu-ray Disc player

HDMI

OUT

HDMI cable

(sold separately)

To household power outlet

(AC 120 V, 60 Hz)

HDMI cable

(sold separately)

Power cord

(supplied)

HDMI

NOTE

• Do not plug in the power cord until all connections have been completed.

• Do not bundle power cords together with connection cables. Doing so can result in humming or noise.

The “Simple Version” describes the installation, connection and setup methods for 5.1-channel speakers.

See page 49 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.

ENGLISH

Turn on power

Turn on the TV and subwoofer power.

Power on

Change the TV input to the input of

this unit.

Press POWER ON to turn on power

to the unit.

The power indicator ﬂashes green and the power turns on.

Power on

1 2 3 4 5

The acoustic characteristics of the connected speakers and listening room are measured and the optimum settings are made automatically. This is called “Audyssey Auto Setup”. To perform measurement, place the setup microphone in multiple locations all around the listening area. For best results, we recommend you measure in six or more positions, as shown in the illustration (up to eight positions).

• When performing Audyssey Auto Setup, MultEQ® XT/Dynamic EQ®/Dynamic

Volume™ functions become active (vpage75, 76).

• To set up the speakers manually, use “Speaker Setup” (vpage79) on the menu.

NOTE

• Make the room as quiet as possible. Background noise can disrupt the room measurements. Close windows, silence cell phones, televisions, radios, air conditioners, ﬂuorescent lights, home appliances, light dimmers, or other devices as measurements may be affected by these sounds.

• Cell phones should be placed away from all audio electronics during the measurement process as Radio Frequency Interference (RFI) may cause measurement disruptions (even if the cell phone is not in use).

• Do not unplug the setup microphone from the main unit until Audyssey Auto Setup is completed.

• Do not stand between the speakers and setup microphone or allow obstacles in the path while the measurements are being made. This will cause inaccurate readings.

• Loud test sounds may be played during Audyssey Auto setup. This is part of normal operation. If there is background noise in room, these test signals will increase in volume.

• Operating

• Measurement cannot be performed when headphones are connected.

Set up speakers (Audyssey® Auto Setup)

VOL df during the measurements will cancel the measurements.

1 2 3 4 5

Power on

ENGLISH

Set up speakers (Audyssey® Auto Setup)

About setup microphone placement

• Measurements are performed by placing the setup microphone successively at multiple positions throughout the entire listening area, as shown in GExample qH. For best results, we recommend you measure in six or more positions, as shown in the illustration (up to eight positions).

• Even if the listening environment is small as shown in GExample wH, measuring at multiple points throughout the listening environment results in more effective correction.

GExample qH GExample wH

FL SW C FR

( : Measuring positions)

FL Front speaker (L) SW Subwoofer FR Front speaker (R) SL Surround speaker (L) C Center speaker SR Surround speaker (R)

SRSL

FL SW C FR

( : Measuring positions)

SRSL

About the main listening position (*M)

The main listening position is the position where listeners would normally sit or where one would normally sit alone within the listening environment. Before starting Audyssey Auto Setup, place the setup microphone in the main listening position. Audyssey MultEQ® XT uses the measurements from this position to calculate speaker distance, level, polarity, and the optimum crossover value for the subwoofer.

Prepare the setup microphone

Mount the setup microphone on a tripod or stand and place it in the main listening position.

When placing the setup microphone, adjust the height of the sound receptor to the level of the listener’s ear.

Sound receptor

NOTE

• Do not hold the setup microphone in your hand during measurements.

• Avoid placing the setup microphone close to a seat back or wall as sound reﬂections may give inaccurate results.

Set up the subwoofer

Setup microphone

If using a subwoofer capable of the following adjustments, set up the subwoofer as shown below.

n When using a subwoofer with a direct mode

Set the direct mode to “On” and disable the volume adjustment and crossover frequency setting.

n When using a subwoofer without a direct mode

Make the following settings:

• Volume : “12 o’clock position”

• Crossover frequency : “Maximum/Highest Frequency”

• Low pass ﬁlter : “Off”

• Standby mode : “Off”

NOTE

When you use two subwoofers, please adjust the subwoofer volume controls individually so that each subwoofer level is as close as possible to 75 dB using the test tone (vpage81) before Audyssey Auto Setup.

Set up the remote control unit

n Set up the zone mode

Press ZONE SELECT to switch the zone mode to “MAIN”.

The “MAIN” indicator lights.

Press ZONE SELECT

n Set up the operation mode

Press AMP to set the remote control unit to amplier operation mode.

Press AMP

Basic version Advanced version InformationSimple version

The “Simple Version” describes the installation, connection and setup methods for 5.1-channel speakers.

See page 49 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.

ENGLISH

Set up speakers (Audyssey® Auto Setup)

STEP 1

Preparation

Connect the setup microphone to the

SETUP MIC jack of this unit.

When the setup microphone is connected, the following screen is displayed.

AUTO SE TUP AUDYSSE Y AUTO S ETUP

STE P1 P repara tion Con nect the s peaker s and pla ce the m acco rding to the re commen datio ns i n the manual . Set the follo wing ite ms i f nece ssary.

Amp Ass ign Cha nnel Selec t

Aut o Se tup St art

Sta rt A uto Se tup

ENT ER En ter RE TURN Cance l

Here, we explain setup using the example of

5.1-channel speaker playback. For settings other than 5.1-channel surround, select “Amp Assign” and perform step 3 and 4 of “Set up “Amp Assign”” (vpage53). If unused channels are set with “Channel Select”, measuring time can be shortened. For setting, perform steps 5 to 10 of “Set up “Channel Select”” (vpage53).

Use ui to select “Auto Setup Start”

and then press ENTER.

Mul tEQ XT

[1/ 6]

STEP 2

Speaker Detection

• In STEP 2, you will perform measurements at the main listening position.

• This step automatically checks the speaker conﬁguration and speaker size, and calculates the channel level, distance, and crossover frequency. It also corrects distortion in the listening area.

Select “Measure” and then press

ENTER.

When measuring begins, a test tone is output from each speaker.

• Measurement requires several minutes.

The detected speakers are displayed.

AUTO SE TUP AUDYSSE Y AUTO S ETUP

STE P2 S pkr De tect C heck

Fro nt Cen ter Sub woof er Sur roun d

Ret ry

Nex t Measu rement

Go to S tep 3 (Measu reme nt) af ter sp eak er c heck

Yes Yes Yes Yes

ENT ER En ter RE TURN Cance l

NOTE

If a connected speaker is not displayed, the speaker may not be connected correctly. Check the speaker connection.

Use ui to select “Next 1

Measurement” and then press ENTER.

Mul tEQ XT

[2/ 6]

NOTE

If “Caution” is displayed:

Go to “Error messages” (vpage 10), check any related items, and perform the necessary procedures. If the problem is resolved, return and restart “Audyssey Auto Setup”.

When performing Audyssey Auto Setup over again

Press ui to select “Retry”, and then press ENTER.

When measuring has stopped

Press RETURN, to the “Cancel Auto Setup?” prompt is displayed. Press o to select “Yes”, then press ENTER.

Setting up the speakers again

Repeat the operation from step 4 of

STEP1 Preparation

STEP 3

Measurement

• In STEP 3, you will perform measurements at multiple positions (two to eight positions) other than the main listening position.

• You can achieve a more effective correction of distortion within the listening area by performing measurements at multiple positions.

Move the setup microphone to

position 2, use ui to select “Measure”, and then press ENTER.

The measurement of the second position starts. Measurements can be made in up to eight positions.

AUTO SE TUP AUDYSSE Y AUTO S ETUP

STE P3 M easure ment Ple ase place the mi crop hone at ea r heig ht at 2nd listen ing pos itio n.

Mea sure

Nex t Calcu lation

Sta rt n ext me asurem ent. Test Tone w ill sta rt

ENT ER En ter RE TURN Cance l

If you want to omit measurements from the next position onward, select “Next 1 Calculation”.

STEP4 Calculation

(Go to

Repeat step 9, measuring positions 3

to 8.

When measurement of position 8 is completed, a “Measurements ﬁnished.” message is displayed.

AUTO SE TUP AUDYSSE Y AUTO S ETUP

STE P3 M easure ment Mea sure ments finish ed.

Mul tEQ XT

[3/ 6]

)

Mul tEQ XT

[3/ 6]

Ret ry

Nex t Calcu lation

Pro ceed to St ep 4 ( Anal yze)

Remote control operation

buttons

Move the cursor (Up/Down/Left/Right)

Conﬁrm the setting Return to previous menu

ENT ER En ter RE TURN Cance l

ENGLISH

Set up speakers (Audyssey® Auto Setup)

STEP 4

Calculation

On the

to select “Next 1 Calculation”, and then press ENTER.

Measuring results are analyzed, and the frequency response of each speaker in the listening room is determined.

STE P4 C alcula tion Now cal culati ng... Ple ase wait.

25%

• Analysis takes several minutes to complete. The time required for this analysis depends on the number of speakers connected. The more connected speakers there are, the longer it takes to perform analysis.

STEP3

AUTO SE TUP AUDYSSE Y AUTO S ETUP

screen, use ui

Mul tEQ XT

[4/ 6]

STEP 5

Check

Use ui to select the item you want

to check, and then press ENTER.

AUTO SE TUP AUDYSSE Y AUTO S ETUP

STE P5 C heck Che ck p rocess ing re sult s. T o proc eed,pr ess “Ne xt”

Spk r Co nfig C heck

Dis tanc e Chec k Ch. Le vel Ch eck Cro ssov er Che ck

Nex t Store

Sel ect item t o chec k

ENT ER En ter RE TURN Cance l

• Subwoofers may measure a greater reported distance than the actual distance due to added electrical delay common in subwoofers.

• If you want to check another item, press

RETURN.

Use ui to select “Next 1 Store”

and then press ENTER.

NOTE

• If the result differs from the actual connection status, or if “Caution!” is displayed, see “Error messages” (vpage10). Then carry out Audyssey Auto Setup again.

• If the result still differs from the actual connection status after remeasurement or the error message still appears, it is possible that the speakers are not connected properly. Turn this unit off, check the speaker connections and repeat the measurement process from the beginning.

• If you change speaker positions or orientation, perform Audyssey Auto Setup again to ﬁnd the optimal equalizer settings.

Mul tEQ XT

[5/ 6]

STEP 6

Store

Select “Store” and then press ENTER.

Save the measurement results.

AUTO SE TUP AUDYSSE Y AUTO S ETUP

STE P6 S tore Pre ss “ Store” to st ore cal cula tion r esults .

Sto re

App ly a nd sto re mea sure ment r esult

AUTO SE TUP AUDYSSE Y AUTO S ETUP

STE P6 S tore Now sto ring.. . Ple ase wait.

25%

ENT ER En ter RE TURN Cance l

• Saving the results requires about 10 seconds.

• If the measuring results are not to be saved,

press RETURN. A message “Cancel Auto Setup?” will be displayed. Press o then select “Yes”. All the measured Audyssey Auto Setup data will be erased.

NOTE

During saving of measurement results, be sure not to turn off the power.

Mul tEQ XT

[6/ 6]

Mul tEQ XT

[6/ 6]

Finish

Unplug the setup microphone from

the unit’s SETUP MIC jack.

Set Dynamic Volume™.

AUTO SE TUP AUDYSSE Y AUTO S ETUP

Fin ish Sto ring compl ete. Aut o Se tup is now fin ishe d. Ple ase un plug mic roph one.

Tur n on Dynam ic Vol ume?

Yes No

Tur n Dy namic Volume on and ex it Aut o S etup

ENT ER Ex it

• For details of Dynamic Volume settings, see page 76.

n When turning Dynamic Volume on

Use o to select “Yes“, and then press ENTER.

• The unit automatically enters “Evening” mode.

n When turning Dynamic Volume off

Use p to select “No“, and then press ENTER.

NOTE

After performing Audyssey Auto Setup, do not change the speaker connections or subwoofer volume. In event of a change, perform Audyssey Auto Setup again.

Mul tEQ XT

[6/ 6]

Basic version Advanced version InformationSimple version

Remote control operation

buttons

Move the cursor (Up/Down/Left/Right)

Conﬁrm the setting Return to previous menu

ENGLISH

Error messages

An error message is displayed if Audyssey® Auto Setup could not be completed due to speaker placement, the measurement environment, etc. If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey Auto Setup over again.

NOTE

Be sure to turn off the power before checking speaker connections.

Examples Error details Measures

AUTO SE TUP AUDYSSE Y AUTO S ETUP

No micr ophone or Sp eake r

Che ck c ause o f prob lem!

AUTO SE TUP AUDYSSE Y AUTO S ETUP

Amb ient noise is to o hi gh or Leve l is t oo low

Che ck c ause o f prob lem!

AUTO SE TUP AUDYSSE Y AUTO S ETUP

Cau tion !

Fro nt R Non e

Cau tion !

Ret ry

Cau tion !

Ret ry

Mul tEQ XT

RET URN Can cel

Mul tEQ XT

RET URN Can cel

Mul tEQ XT

• The connected setup microphone is broken,

or a device other than the supplied setup microphone is connected.

• Not all speakers could be detected.

• The front L speaker was not properly detected.

• There is too much noise in the room for accurate measurements to be made.

• Speaker or subwoofer sound is too low for accurate measurements to be made.

• The displayed speaker could not be detected. • Check the connections of the displayed

• Connect the included setup microphone to the SETUP MIC jack of this unit.

• Check the speaker connections.

• Either turn off any device generating noise or move it away.

• Perform again when the surroundings are quieter.

• Check the speaker installation and the direction in which the speakers are facing.

• Adjust the subwoofer’s volume.

speaker.

Parameter Check

This function enables you to check the measurement results and equalizer characteristics after Audyssey Auto Setup.

Use ui to select “Parameter Check” and then

press ENTER or p.

Use ui to select the item you want to check, then

press ENTER or p.

Measurement results for each speaker are displayed.

AUTO SE TUP PARAMET ER CHECK

Spe aker Confi g Chec k

Dis tanc e Chec k Cha nnel Level Check Cro ssov er Che ck EQ Chec k

Res tore

Sho w sp eaker config urat ion re sult

Speaker Conﬁg. Check

Distance Check

Channel Level Check

Crossover Check

EQ Check

• If “EQ Check” is selected in step 2, press

curve (“Audyssey” or “Audyssey Flat”) to be checked. Use o p to switch the display between the different speakers.

Check the speaker conﬁguration.

Check the distance.

Check the channel level.

Check the crossover frequency.

Check the equalizer.

ui to select equalizing

Ret ry

Che ck c ause o f prob lem!

AUTO SE TUP AUDYSSE Y AUTO S ETUP

Fro nt L P hase

Ret ry Ski p

Che ck c ause o f prob lem!

RET URN Can cel

Mul tEQ XT

Cau tion !

RET URN Can cel

Remote control operation

buttons

• The displayed is connected with the polarities reversed.

Move the cursor (Up/Down/Left/Right)

• Check the polarities of the displayed speaker.

• For some speakers, this error message may be displayed even if the speaker is properly connected. If you are sure the connection is correct, press ui to select “Skip”, then press ENTER.

Conﬁrm the setting Return to previous menu

Press RETURN.

The conﬁrmation screen reappears. Repeat steps 2.

Retrieving Audyssey Auto Setup settings

If you set “Restore” to “Yes”, you can return to Audyssey Auto Setup measurement result (value calculated at the start by MultEQ® XT) even when you have changed each setting manually.

ENGLISH

Play back disc

Press BD to switch an input source for a player used for playback.

Play the component connected to this unit.

Make the necessary settings on the player (language setting, subtitles setting, etc.) beforehand.

Adjust the sound volume.

VOL d ........................................... Volume up

VOL f ...................................... Volume down

MUTE .................................................. Muting

Set the listening mode.

Set the listening mode according to the playback contents

(cinema, music, etc.) or according to your liking (vpage 45 “Selecting a listening mode (Surround mode)”).

1 2 3 4 5

When power is switched to standby

Press POWER OFF.

GPower indicator status in standby modeH

• Normal standby : Off

• When “HDMI Control” is set to “ON” : Red

• When “Network Standby” is set to “ON” : Red

You can also switch the power to standby by pressing ON/STANDBY on the main unit.

NOTE

During power standby, a minimal amount of power is consumed. To totally cut off the power, remove the power cord from the power outlet.

Basic version Advanced version InformationSimple version

Remote control operation

buttons

Move the cursor (Up/Down/Left/Right)

Conﬁrm the setting Return to previous menu

ENGLISH

Basic version

Here, we explain the connections and basic operation methods for this unit.

F Connections F Playback (Basic operation) F Selecting a listening mode (Surround mode) vpage45

n Refer to the pages indicated below for information on connecting and playing back the various

media and external devices.

Audio and Video

TV Blu-ray Disc player DVD player Set-top box (Satellite tuner or cable TV) Digital video recorder Game console Digital camcorder Control dock for iPod

Audio

iPod USB memory device SIRIUS satellite radio HD Radio receiver CD player Record player

Network

For speaker connections, see page 4.

PlaybackConnection

vpage15, 16 vpage15, 16 vpage25 vpage15, 17 vpage25 vpage15, 17 vpage15, 18 vpage15 vpage18 vpage19 vpage25

vpage19 vpage27 vpage19 vpage43 vpage20 vpage28 vpage20 vpage30 vpage21 vpage25 vpage21

vpage22

–

– – – –

PlaybackConnection

–

PlaybackConnection

–

ENGLISH

Connections

Important information

• Make connections as follows before using this unit. Select an appropriate connection type according to the components to be connected.

• You may need to make some settings on this unit depending on the connection method. Refer to each description for more information.

• Select the cables (sold separately) according to the components being connected.

NOTE

• Do not plug in the power cord until all connections have been completed.

• When making connections, also refer to the operating instructions of the other components being connected.

• Be sure to connect the left and right channels properly (left with left, right with right).

• Do not bundle power cords together with connection cables. Doing so can result in noise.

Converting input video signals for output (Video conversion function)

This unit is equipped with four types of video input connectors (HDMI, Component video, S-Video and video) and three types of video output connectors (HDMI, Component video and video). Use the connectors corresponding to the components to be connected. This function automatically converts various formats of video signals input to this unit into the formats used to output the video signals from this unit to a monitor.

GFlow of video signals for MAIN ZONEH

Video device

Output

HDMI connector

Component video

connectors

Input

(IN)

HDMI connector

Component video

connectors

This unit

Output

(MONITOR OUT)

HDMI

connector

Component video

connectors

Monitor

Input

HDMI connector

Component video

connectors

GFlow of video signals for ZONE2H

Video device

Output

S-Video connector

Video connector

This unit

Input

(IN)

S-Video connector

Video connector Video connector Video connector

Output

(MONITOR OUT)

Monitor

Input

in Set as Necessary

• Set when not using the video conversion function.

“Video Convert” (vpage70)

• Set when changing the resolution of the video signal.

“Resolution” (vpage71)

• The video conversion function supports the NTSC, PAL, SECAM, NTSC 4.43, PAL-N, PAL-M and PAL-60 formats.

• The resolution of the video signal input to this unit’s HDMI connector is the one set at “Resolution” (vpage71). (1080p HDMI signals and 1080p component signals are output at 1080p, regardless of the setting.)

• Resolutions of HDMI-compatible TVs can be checked at “HDMI Monitor 1 Information” or “HDMI Monitor 2 Information” (vpage90).

NOTE

• HDMI signals cannot be converted into analog signals.

• When a non-standard video signal from a game machine or some other source is input, the video conversion function might not operate.

• Component video input signals cannot be converted into Video format.

• A menu is output via the HDMI connector or component video connector.

Simple version Advanced version InformationBasic version

S-Video connector

Video connector

S-Video connector

Video connector

ENGLISH

Important information

Examples of screen display

• Menu screen • Status display screen When the input source is

When the volume is adjusted

switched

Audi o/Vide o Adjus t

Info rmatio n Auto Setup Manu al Set up Inpu t Setu p

Adju st var ious au dio an d vide o param eters

Inpu t A uto

STER EO

Mode

Mast er Vo lume -80.0d B

Status display: The operating status appears brieﬂy on the screen

when the input source is switched or the volume is changed.

NOTE

• If you operate the menu while playing back 3D video content, the playback video is replaced by the menu screen. The playback video is not displayed behind the menu screen.

• This unit does not show the status display while playing back 3D video content.

Connecting an HDMI-compatible device

You can connect up to ﬁve HDMI-compatible devices to the unit.

HDMI function

This unit supports the following HDMI functions:

• 3D

• Deep Color (vpage111)

• Auto Lip Sync (vpage82, 111)

• x.v.Color, sYCC601 color, Adobe RGB color, Adobe YCC601 color (vpage111, 112)

• High deﬁnition digital audio format

• ARC (Audio Return Channel)

• Content Type

• CEC (HDMI control)

In order to play back digital video and audio such as BD-Video or DVD-Video via HDMI connection, both this unit and TV or the player need to support the copyright protection system known as HDCP (Highbandwidth Digital Content Protection System). HDCP is copyright protection technology comprised of data encryption and authentication of the connected AV device. This unit supports HDCP.

• If a device that does not support HDCP is connected, video and audio are not output correctly. Read

the owner’s manual of your television or player for more information.

About HDMI cables

• When a device supporting Deep Color signal transfer is connected, use a cable compatible “High Speed HDMI cable” or “High Speed HDMI cable with Ethernet”.

• When the ARC function is used, connect a device with a ”Standard HDMI cable with Ethernet” or “High Speed HDMI cable with Ethernet” for HDMI 1.4.

HDMI control function (vpage54)

This function allows you to operate external devices from the receiver and operate the receiver from external devices.

NOTE

• The HDMI control function may not work depending on the device it is connected to and its settings.

• You cannot operate a TV or Blu-ray Disc player/DVD player that is not compatible with the HDMI control function.

About 3D function

This unit supports input and output of 3D (3 dimensional) video signals of the HDMI 1.4 standards. For playing the 3D video content, a player, and a TV that support the 3D function of the HDMI 1.4 standards are required in addition to this unit.

NOTE

• If you operate the menu while playing back 3D video content, the playback video is replaced by the menu screen. The playback video is not displayed behind the menu screen.

• This unit does not show the status display while playing back 3D video content.

About ARC (Audio Return Channel) function

The Audio Return Channel in HDMI 1.4 enables a TV, via a single HDMI cable, to send audio data “upstream” to this unit.

NOTE

• To enable the ARC function, set “HDMI Control” to “ON” (vpage82).

• ARC function is only supported for the HDMI MONITOR OUT 1 connector. In order to use the ARC function, connect the television to the HDMI MONITOR OUT 1 connector.

• When connecting a TV that does not support the ARC function, a separate connection using an audio cable is required. In this case, refer to “Connecting a TV” (vpage16) for the connection method.

About Content Type

The HDMI speciﬁcation version 1.4 enables simple, automated picture setting selection with no user intervention.

NOTE

To enable the Content Type, set “Video Mode” to “Auto” (vpage70).

ENGLISH

Cables used for connections

Audio and video cable (sold separately)

HDMI cable

• This interface allows transfer of digital video signals and digital audio signals over a single HDMI cable.

Blu-ray

Disc

player

HDMI

OUT

Digital

camcorder

HDMI

OUT

DVD

player

HDMI

OUT

Set-top

box

HDMI

OUT

Digital

video

recorder

HDMI

OUT

Game

console

HDMI

OUT

TV 1

HDMI

TV 2

HDMI

GRear panelH

Connecting an HDMI-compatible device

• When this unit is connected to other devices with HDMI cables, connect this unit and TV also with an HDMI cable.

• When connecting a device that supports Deep Color transmission, please use a “High Speed HDMI cable” or “High Speed HDMI cable with Ethernet”.

• Video signals are not output if the input video signals do not match the monitor’s resolution. In this case, switch the Blu-ray Disc/DVD player’s resolution to a resolution with which the monitor is compatible.

• When this unit and monitor are connected with an HDMI cable, if the monitor is not compatible with HDMI audio signal playback, only the video signals are output to the monitor.

NOTE

• The HDMI signal is not simultaneously output to HDMI MONITOR 1 and HDMI MONITOR 2. Select the connector that you want to use in advance using “Monitor Out” (vpage82) in the menu, or by pressing the MONITOR SELECT button on the remote control.

• HDMI control function is only supported for the HDMI MONITOR OUT 1 connector. In order to use the HDMI control function, connect the television to the HDMI MONITOR OUT 1 connector.

• The audio signal from the HDMI output connector (sampling frequency, number of channels, etc.) may be limited by the HDMI audio speciﬁcations of the connected device regarding permissible inputs.

Connecting to a device equipped with a DVI-D connector

When an HDMI/DVI conversion cable (sold separately) is used, the HDMI video signals are converted to DVI signals, allowing connection to a device equipped with a DVI-D connector.

NOTE

• No sound is output when connected to a device equipped with a DVI-D connector. Make separate audio connections.

• Signals cannot be output to DVI-D devices that do not support HDCP.

• Depending on the combination of devices, the video signals may not be output.

n Settings related to HDMI connections

Set as necessary. For details, see the respective reference pages.

Simple version Advanced version InformationBasic version

GFront panelH

Input Assign (vpage69)

Set this to change the HDMI input connector to which the input source is assigned.

HDMI Setup (vpage82)

Make settings for HDMI video/audio output.

• RGB Range • HDMI Control

• Auto Lip Sync • Standby Source

• HDMI Audio Out • Power Off Control

• Monitor Out

NOTE

The audio signals output from the HDMI connectors are only the HDMI input signals.

ENGLISH

Connecting a TV

• Select the connector to use and connect the device.

• For video connections, see “Converting input video signals for output (Video conversion function)”

(vpage13).

• For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage14).

To listen to TV audio through this device, use the optical digital connection.

NOTE

This connection is not required when a TV compatible with the ARC function (Audio Return Channel (HDMI

1.4 standard function) is connected to this unit via an HDMI connection. For details, see “About ARC (Audio Return Channel) function” (vpage 14) or refer to the instruction manual for your TV.

Cables used for connections

Video cable (sold separately)

Video cable

Component video cable

Optical cable

Y P

B PR

VIDEO

COMPONENT VIDEO

VIDEO

(Yellow)

(Green)

(Blue)

(Red)

Audio cable (sold separately)

AUDIO

OPTICAL

OUT

Connecting a Blu-ray Disc player

• You can enjoy video and audio from a Blu-ray Disc.

• Select the connector to use and connect the device.

• For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage14).

Cables used for connections

Video cable (sold separately)

Video cable

Audio cable

Blu-ray Disc

(Yellow)

Audio cables (sold separately)

(White)

(Red)

player

VIDEO

OUT

AUDIO

OUT

in Set as Necessary

Set this to change the digital input connector or component video input connector to which the input source is assigned. “Input Assign” (vpage69)

in Set as Necessary

Set this to change the digital input connector or component video input connector to which the input source is assigned. “Input Assign” (vpage69)

For HD audio (Dolby TrueHD, DTS-HD, Dolby Digital Plus and DTS Express) playback, connect with HDMI (vpage14 “Connecting an HDMI-compatible device”).

ENGLISH

Connecting a DVD player

• You can enjoy video and audio from a DVD.

• Select the connector to use and connect the device.

• For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage14).

Cables used for connections

Video cable (sold separately)

Video cable

Component video cable

Audio cable

Coaxial digital cable

DVD player

COMPONENT VIDEO

Y P

(Yellow)

(Green)

(Blue)

(Red)

Audio cables (sold separately)

(White)

(Red)

(Orange)

VIDEO AUDIO

VIDEO

OUT

B PR

OUT

AUDIO

OUT

COAXIAL

OUT

Connecting a set-top box (Satellite tuner/cable TV)

• You can watch satellite or cable TV.

• Select the connector to use and connect the device.

• For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage14).

Cables used for connections

Video cable (sold separately)

Video cable

Component video cable

Audio cable

Coaxial digital cable

Satellite tuner/Cable TV

COMPONENT VIDEO

OUT

Y P

(Yellow)

(Green)

(Blue)

(Red)

Audio cables (sold separately)

COAXIAL

OUT

B PR

VIDEO

(White)

(Red)

(Orange)

VIDEO

OUT

AUDIO

OUT

Simple version Advanced version InformationBasic version

in Set as Necessary

Set this to change the digital input connector or component video input connector to which the input source is assigned. “Input Assign” (vpage69)

in Set as Necessary

Set this to change the digital input connector or component video input connector to which the input source is assigned. “Input Assign” (vpage69)

ENGLISH

Connecting a digital video recorder

• You can record video onto a Blu-ray Disc or DVD.

• Select the connector to use and connect the device.

• When recording analog audio, use the analog connection.

• See “REC OUT mode” (vpage56) for operating instructions.

• For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage14).

Cables used for connections

Video cable (sold separately)

Video cable

S-Video cable

Audio cable

Optical cable

(Yellow)

Audio cable (sold separately)

(White)

(Red)

Digital video recorder

S-VIDEO VIDEO

OUT

VIDEO

OUT

OPTICAL

OUT

RL RL

AUDIOAUDIO VIDEOVIDEO

OPTICAL

AUDIOAUDIO

Connecting a digital camcorder

• You can enjoy video and audio from a digital camcorder.

• You can enjoy games by connecting a game machine via the V.AUX input connector. In this case, select the input source to “V.AUX”.

• For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage14).

Cables used for connections

Video cable (sold separately)

Video cable

Audio cable

Digital camcorder

VIDEO

OUT

(Yellow)

Audio cable (sold separately)

(White)

(Red)

AUDIOVIDEO

AUDIO

OUT

in Set as Necessary

Set this to change the digital input connector or component video input connector to which the input source is assigned. “Input Assign” (vpage69)

NOTE

To record video signals through this unit, use the same type of video cable for connection between this unit and the player as used for connection between this unit and the recorder.

in Set as Necessary

Set this to change the digital input connector or component video input connector to which the input source is assigned.

“Input Assign” (vpage69)

NOTE

When a non-standard video signal from a game machine or some other source is input, the video conversion function might not operate. In this case, use the monitor output of the same connector as the input.

ENGLISH

Connecting a control dock for iPod

• Connect a control dock for iPod to the unit to enjoy video and music stored on an iPod.

• For a control dock for iPod, use ASD-1R and ASD-11R made by DENON (sold separately).

• For instructions on the control dock for iPod settings, refer to the control dock for iPod’s operating instructions.

Control dock for iPod

ASD-11R

Use the AV/Control Cable supplied with the DENON control

dock for iPod.

You can also connect the iPod you are using directly to the USB port of this unit (vpage19 “Connecting an iPod or USB memory device to the USB port”).

NOTE

When connecting an iPone to this unit, keep the iPhone at least 20 cm away from this unit. If the iPhone is kept closer to this unit and a telephone call is received by the iPhone, noise may be output from this device.

Connecting an iPod or USB memory device to the USB port

You can enjoy music stored on an iPod or USB memory device.

Cables used for connections

To connect an iPod to this unit, use the USB cable supplied with the iPod.

iPod

USB memory

device

• When you want to playback a video ﬁle stored on an iPod, use a DENON control dock for iPod (ASD-1R

and ASD-11R, sold separately) (vpage19 “Connecting a control dock for iPod”).

• With iPods, playback is possible with iPhone, iPod touch, classic and nano released from the 5th-generation of iPods. For details, check the DENON web site or page 27.

• DENON does not guarantee that all USB memory devices will operate or receive power. When using a portable USB connection type HDD of the kind to which an AC adapter can be connected to supply power, use the AC adapter.

NOTE

• USB memory devices will not work via a USB hub.

• Do not use an extension cable when connecting a USB memory device. This may cause radio interference with other devices.

Simple version Advanced version InformationBasic version

ENGLISH

Connecting an antenna

Connecting a SIRIUS connector

• This unit is a SIRIUS Satellite Radio Ready® receiver. You can receive SIRIUS® Satellite Radio by connecting to the SiriusConnect Home Tuner and subscribing to the SIRIUS service.

• Plug the SIRIUS connector on the SIRIUS service.

• Position the Home Tuner antenna near a south-facing window to receive the best signal. For details, see “Listening to SIRIUS satellite radio” (vpage 28). When making connections, also refer to the operating instructions of the SiriusConnect Home Tuner.

SiriusConnect Home Tuner

When connecting digital audio

in Set as Necessary

When connecting digital of the SiriusConnect Home Tuner, perform the setting “Digital”.

“Input Assign” (vpage69)

NOTE

Keep the power cord unplugged until the SiriusConnect Home Tuner connection have been completed.

n Positioning the antenna

For a consistent satellite signal, the antenna must be positioned correctly. Use the following map to determine which area you are in and position the antenna accordingly.

SKY

NORTH

WEST

Area 1 Point the antenna toward the sky in the east, northeast, or

southeast, either through a window or outside.

Area 2 Point the antenna toward the sky in the north or northeast,

either through a window or outside.

Area 3 Point the antenna toward the sky in the north or northwest,

either through a window or outside.

Area 4 Point the antenna toward the sky in the west, northwest, or

southwest, either through a window or outside.

Area 5 Put the antenna outside and point it straight up. The antenna

cannot be used indoors.

SOUTH

HORIZON

EAST

Connecting an HD Radio receiver

• By connecting a HD Radio antenna to this unit, you can receive HD Radio programs.

• HD Radio broadcasting currentry is available in the United States and select other countries.

Direction of broadcasting station

FM outdoor antenna

75 Ω coaxial

cable

FM indoor

antenna (for

HD Radio

broadcasting,

supplied)

White

Black

AM loop antenna (for HD Radio broadcasting, supplied)

• To prevent interference, install at least 3.3 ft/1 m away from the antenna connected to the this unit’s other AM tuner terminal.

w eq

Ground

AM outdoor

antenna

ENGLISH

n AM loop antenna assembly

Put the stand section

through the bottom of the loop antenna from the rear and bend it forward.

Loop

antenna

Insert the projecting part

into the square hole in the stand.

n Using the AM loop antenna

Suspending on a wall

Suspend directly on a wall without assembling.

Standing alone

Use the procedure shown left to assemble.

Connecting an antenna

Stand

Square hole

Projecting part

Nail, tack, etc.

Connecting a record player

You can enjoy playing records.

Cables used for connections

Audio cable (sold separately)

Audio cable

(MM cartridge)

AUDIO

OUT

(White)

(Red)

Turntable

GND

Connecting a CD player

• You can enjoy CD sound.

• Select the connector to use and connect the device.

Simple version Advanced version InformationBasic version

Cables used for connections

Audio cable

CD player

Audio cable (sold separately)

(White)

(Red)

AUDIO

OUT

NOTE

• Do not connect two FM antennas simultaneously.

• Even if an external AM antenna is used, do not disconnect the AM loop antenna.

• Make sure the AM loop antenna lead terminals do not touch metal parts of the panel.

• If the signal has noise interference, connect the ground terminal (GND) to reduce noise.

• If you are unable to receive a good broadcast signal, we recommend installing an outdoor antenna. For details, inquire at the retail store where you purchased the unit.

in Set as Necessary

Set this to change the digital input connector to which the input source is assigned. “Input Assign” (vpage69)

• This unit is compatible with record players with an MM cartridge. When you connect to a record player with an MC cartridge, use a commercially available MC head amp or a step-up transformer.

• When you increase the volume without connecting the record player, there may be “booming” noise from the speakers.

NOTE

The SIGNAL GND terminal of this unit is not a safety ground connection. Connect it to reduce noise when noise is excessive. Note that depending on the record player, connecting the ground line may have the reverse effect of increasing noise. In this case, it is not necessary to connect the ground line.

ENGLISH

Connecting to a home network (LAN)

• This unit lets you play via your home network (LAN) music ﬁles stored on a computer and music content such as that from Internet radio. You can also operate this unit from a computer using the Web control function.

• You can update by downloading the latest ﬁrmware from the DENON website. For more information, on the menu, select “Firmware Update” (vpage89).

• See “Network Setup” on the menu (vpage84) for more information on network setting.

Cables used for connections

Cable (sold separately)

Ethernet cable

Computer

Modem

Internet

Required system

n Broadband internet connection n Modem

Device that connects to the broadband circuit and conducts communications on the Internet. A type that is integrated with a router is also available.

n Router

When using this unit, we recommend you use a router equipped with the following functions:

• Built-in DHCP server This function automatically assigns IP addresses on the LAN.

• Built-in 100BASE-TX switch When connecting multiple devices, we recommend a switching hub with a speed of 100 Mbps or greater.

n Ethernet cable (CAT-5 or greater recommended)

• Use only shielded STP or ScTP LAN cable which is available at retailer.

• Some ﬂat type Ethernet cables are easily affected by noise. We recommend using a normal type cable.

NOTE

• A contract with an ISP is required to connect to the Internet. No additional contract is needed if you already have a broadband connection to the Internet.

• The types of routers that can be used depend on the ISP. Contact an ISP or a computer shop for details.

• DENON assumes no responsibility whatsoever for any communication errors or troubles resulting from customer’s network environment or connected devices.

• This unit is not compatible with PPPoE. A PPPoE-compatible router is required if you have a contract for a type of line set by PPPoE.

• Do not connect an ETHERNET connector directly to the LAN port/ Ethernet connector on your computer.

To WAN side

To LAN port

Router

For connections to the Internet, contact an ISP (Internet Service Provider) or a computer shop.

LAN port/

Ethernet

connector

• If you have an Internet provider contract for a line on which network settings are made manually, make the settings at “Network Setup” (vpage84).

• With this unit, it is possible to use the DHCP and Auto IP functions to make the network settings automatically.

• When using this unit with the broadband router’s DHCP function enabled, this unit automatically performs the IP address setting and other settings. When using this unit connected to a network with no DHCP function, make the settings for the IP address, etc., at “Network Setup” (vpage84).

• When setting manually, check the setting contents with the network administrator.

ENGLISH

Connecting a external power ampliﬁer

• You can use this unit as a pre-amp by connecting a commercially available power amp to the PRE OUT connector. Adding a power amp to each of the channels provides an even greater sound presence.

• Select the terminal to use and connect the device.

Cables used for connections

Audio cable (sold separately)

Audio cable

Power ampliﬁer

SUB-

WOOFER

(White)

(Red)

CENTER SURROUND

FRONT

AUDIO

SURROUND

BACK

Connecting an external control device

REMOTE CONTROL jacks

If this unit is installed in a location that is out of range of the signal from the remote control unit, you can still operate the unit and the devices connected to it by using a commercially available IR receiver. You can also use it to remotely control ZONE2, ZONE3 (another room).

Infrared

retransmitter

AUX OUT

Input

RS-232C connector

By connecting an external serial controller, you can control all sorts of household electrical devices (including lights, electric curtains, and air conditioning units) in addition to your audio and video devices.

External serial controller

Infrared sensor

Output

Device equipped with a

REMOTE CONTROL IN jack

Simple version Advanced version InformationBasic version

TRIGGER OUT jacks

When a device with TRIGGER IN jack is connected, the connected device’s power on/standby can be controlled through linked operation to this unit. The TRIGGER OUT jack outputs a maximum 12 V/150 mA electrical signal.

12 V/150 mA trigger-compatible device

in Set as Necessary

Set to change the conditions for linked operation via the TRIGGER OUT 1 or 2 jack. “Trigger Out 1” or “Trigger Out 2” (vpage88)

• When using just one surround back speaker, connect it to the left channel (L) terminal.

• Use the volume control on the subwoofer to control subwoofer volume.

• If the subwoofer volume sounds low, use the volume control provided on the subwoofer to adjust the volume.

NOTE

• When speakers have been connected to PRE OUT terminals, do not connect the speakers to the speaker terminals.

• The output channels for the PRE OUT connector change to SBL and SBR in the “Amp Assign” (vpage79) settings in the menu.

NOTE

If the permissible trigger input level for the connected device is larger than 12V/150mA, or has shorted, the TRIGGER OUT jack cannot be used. In this case, turn off the power to the unit, and disconnect it.

Perform the operation below beforehand.

q Turn on the power of this unit. w Turn off the power of this unit from the external controller. e Check that the unit is in the standby mode.

ENGLISH

Playback (Basic operation)

n Selecting the input source (vpage24) n Adjusting the master volume (vpage24) n Turning off the sound temporarily (vpage25)

n Playing a Blu-ray Disc player/DVD player

(vpage25)

n Playing a CD player (vpage25) n Playing an iPod® (vpage25) n Tuning in radio stations (vpage28) n Playing a network audio (vpage32) n Playing a USB memory device (vpage43)

Selecting a listening mode (Surround mode)

(vpage45)

Playback (Advanced operation) (vpage54)

Important information

Before starting playback, make the connections between the different components and the settings on the receiver.

NOTE

Also refer to the operating instructions of the connected components when playing them.

Selecting the input source

Press the input source select button (NET/USB, iPod, DVD, BD, TUNER,

DOCK, SAT TU, SAT/CBL, GAME, V.AUX, PHONO, CD, DVR, TV) to be

played back.

The desired input source can be selected directly.

• When iPod PLAY is pressed, the input source of this unit is

switched to “DOCK” or “NET/USB” and the connected iPod is automatically played (vpage28 “iPod play function”).

You can also use the following operation to select an input source.

n Using the “Source Select” menu

q Press SOURCE SELECT.

Display the “Source Select” menu.

Sou rc e S el ect :F lic kr

Rec en t S ou rce

q Input Source

The name of the highlighted input source is displayed.

w Recently used sources

The recently used input sources (up to ﬁve) are displayed.

e Icons for the input sources in the different categories are

displayed.

w Use uio p to select the input source,

then press ENTER.

The input source is set and the source

selection menu is turned off.

The currently selected input source is highlighted.

Sel ec t

Ent er

ENT ER

• When using with an iPod connected directly to the USB port of this

unit, select “ (USB/iPod)” for the input source.

• Input sources that are not going to be used can be set ahead of time.

Make this setting at “Source Delete” (vpage87).

• To turn off the source selection menu without selecting an input

source, press SOURCE SELECT again.

n Using the knob on the main unit

Turn SOURCE SELECT.

• If “Rec Select” or “Tuning Preset” mode is selected for the input source, press SOURCE before turning SOURCE SELECT.

• Turning SOURCE SELECT switches the input source, as shown below.

BD DVD TV SAT/CBL GAMEDVR V.AUX

PHONO HD Radio SIRIUS NET/USB DOCKCD

Adjusting the master volume

Use VOL df to adjust the volume.

n When the “Volume Display” setting

(vpage87) is “Relative”

GAdjustable rangeH

– – –

–80.5dB – 18.0dB

n When the “Volume Display” setting (vpage87) is

“Absolute”

GAdjustable rangeH

• The variable range differs according to the input signal and channel level setting.

You can also operate via the main unit. In this case, perform the following operations. Turn MASTER VOLUME to adjust the volume.

0.0 – 99.0

ENGLISH

Important information

Turning off the sound temporarily

Press MUTE.

• The sound is reduced to the level set at “Mute Level” (vpage87).

• To cancel, press MUTE again. Muting can also be canceled by

adjusting the master volume.

Playing a Blu-ray Disc player/DVD player

The following describes the procedure for playing Blu-ray Disc player/ DVD player.

Prepare for playback.

q Turn on the power of the TV,

2 3

subwoofer and player.

w Change the TV input to the input of

this unit.

e Load the disc in the player.

Press POWER ON to turn on power to the unit.

Press BD or DVD to switch an input source for a player used for playback.

Play the component connected to this unit.

Make the necessary settings on the player (language setting, subtitles setting, etc.) beforehand.

Playing a CD player

The following describes the procedure for playing CD player.

Prepare for playback.

q Turn on the power of the subwoofer

2 3 4

There are two methods for iPod playback.

and player.

w Load the disc in the player.

Press POWER ON to turn on power to the unit.

Press CD to switch the input source to the CD player.

Play the component connected to this unit.

Playing an iPod

q Use a DENON control dock for iPod to play back.

You can play back both video, photo and audio.

w Connect an iPod directly to the USB port to play back

(vpage27).

You can play back audio only.

Use a DENON control dock for iPod to play back

DENON control dock for iPod usable on this unit

• ASD-1R / ASD-11R

n Listening to music on an iPod

Prepare for playback.

q Connect the DENON control dock for iPod to this unit

(vpage19 “Connecting a control dock for iPod”).

w Set the iPod

Press POWER ON to turn on power to the unit.

in the DENON control dock for iPod.

Press DOCK to switch the input source to “DOCK”.

• If ”Browse mode” is selected in step 4, the following screen is displayed on a TV screen, depending on the connected control dock for iPod.

(When using an ASD-1R) (When using an ASD-11R)

• In ”Browse mode”, the iPod display is as shown at right.

NOTE

If the connections screen is not displayed, the iPod may not be properly connected. Reconnect it.

Press SEARCH and hold it down for 2 seconds or

more to select the display mode.

• There are two modes for displaying the contents recorded on the iPod.

Browse mode

• English letters, numbers and certain symbols are displayed. Incompatible characters are displayed as “.” (period).

Remote mode

• “Remote iPod” is displayed on the display of this unit.

Display mode

Playable ﬁles

Active buttons

z1 When using an ASD-11R DENON control dock for iPod. z2 Video may not be output, depending on the combination of

ASD-1R or ASD-11R DENON control dock for iPod and iPod.

Display iPod information on the TV screen.

Display iPod information on the iPod screen.

Browse mode Remote mode

Music ﬁle Photo ﬁle Video ﬁle Remote

control unit (This unit)

iPod

P P

OK to disconnect.

Simple version Advanced version InformationBasic version

ENGLISH

Playing an iPod

Use ui to select the item, then

press ENTER or p to select the le to be played.

Press ENTER, p or 1.

Playback starts.

• You can specify the duration of the on-screen display to be displayed

(default: 30 sec) at menu “iPod” (vpage88). Press uio p to return to the original screen.

• To play back compressed audio with extended bass or treble reproduction, we recommend playback in RESTORER mode (vpage78). The default setting is “Mode3”.

• In Browse mode, press playback to check the title name, artist name, and album name.

NOTE

• Press POWER OFF and set this unit’s power to the standby mode before disconnecting the iPod. Also switch the input source to “DOCK” before disconnecting the iPod.

• Depending on the type of iPod and the software version, some functions may not operate.

• Note that DENON will accept no responsibility whatsoever for any problems arising with the data on an iPod when using this unit in conjunction with the iPod.

STATUS during

n Viewing videos on an iPod® in the Browse

mode

When an iPod equipped with a video function is connected to a DENON ASD-11R control dock for iPod, image ﬁles can be played in the Browse mode.

Use ui to select “Videos”, then

press ENTER or p.

Use ui to select the search item

or folder, then press ENTER or

Use ui to select the video le,

then press ENTER, p or 1.

Playback starts.

n Viewing photos and videos on an iPod® in the

Remote mode

This unit can play back on a TV screen photos and data stored on an iPod equipped with a slide show or video function.

Press and hold SEARCH to set the

Remote mode.

“Remote iPod” or “Dock Remote“is displayed on the display of this unit.

Watching the iPod’s screen,

use ui to select “Photos” or “Videos”.

• Depending on the iPod model, it may be necessary to operate the iPod unit directly.

Press ENTER until the image you want to view is

displayed.

“TV Out” at the iPod’s “Slide show Settings” or “Video Settings” must be set to “On” in order to display the iPod’s photo data or videos on the monitor. For details, see the iPod’s operating instructions.

NOTE

Video may not be output, depending on the combination of ASD-1R or ASD-11R and iPod.

n iPod operation

Operation buttons Function

(Press and release)

(Press and hold)

(Press and release)

(Press and hold)

8 9

RESTORER RESTORER TV POWER TV power on/standby (Default : SONY)

• Repeat playback (vpage72 “Repeat”)

• Shufﬂing playback (vpage72 “Shufﬂe”) z When the menu screen is displayed, press

SEARCH, then press o (previous page) or p (next

page). To cancel, press ui or SEARCH.

MENU Amp menu

Cursor operation /

uio p

ENTER

RETURN Return

6 7

3 2

TV INPUT Switch TV input (Default : SONY)

Auto search (cue, ui) /

Manual search (Press and hold, ui)

Enter / Pause

Stop

Page search mode

Browse / Remote mode switching

Manual search

(fast-reverse/fast-forward)

Playback / Pause Auto search (cue)

Pause

Stop

ENGLISH

Connect an iPod directly to the USB port to play back

You can use the USB cable provided with the iPod® to connect the iPod with the unit’s USB port and enjoy music stored on the iPod.

• This unit supports audio playback from the iPod (ﬁfth generation or later), iPod nano, iPod classic, iPod touch and iPhone (it is not compatible with iPod shufﬂe).

Connect the iPod® to the USB port (vpage 19 “Connecting an iPod or USB memory device to the

USB port”).

Press POWER ON to turn on

power to the unit.

Press NET/USB to switch the

input source to “NET/USB”.

DENON:[ AVR-3311 CI]

Favorit e Interne t Radio Media S erver iPod Flickr Napster Pandora

Use ui to select “iPod”, then

press ENTER or p.

iPod

Playlis ts Artists Albums Songs Podcast s Genres Compose rs

NOTE

If the connections screen is not displayed, the iPod may not be properly connected. Reconnect it.

[1/8]

Press SEARCH and hold it down for 2 seconds or

more to select the display mode.

• There are two modes for displaying the contents recorded on the iPod.

Browse mode

• English letters, numbers and certain symbols are displayed. Incompatible characters are displayed as “.” (period).

Remote mode

• “Remote iPod” is displayed on the display of this unit.

• The Remote mode is not supported on ﬁfth generation iPod or ﬁrst generation iPod nano.

Display mode

Playable ﬁles

Active buttons

zOnly the sound is played.

Display iPod information on the TV screen.

Display iPod information on the iPod screen.

Browse mode Remote mode

Music ﬁle Video ﬁle Remote

control unit (This unit)

iPod

P P

Use ui to select the item, then press ENTER or p

to select the le to be played.

Press ENTER, p or 1.

Playback starts.

• You can specify the duration of the on-screen display to be displayed

(default: 30 sec) at menu “iPod” (vpage88). Press uio p to return to the original screen.

• To play back compressed audio with extended bass or treble reproduction, we recommend playback in RESTORER mode (vpage78). The default setting is “Mode3”.

• In Browse mode, press playback to check the title name, artist name, and album name.

NOTE

• Depending on the type of iPod and the software version, some functions may not operate.

• Note that DENON will accept no responsibility whatsoever for any problems arising with the data on an iPod when using this unit in conjunction with the iPod.

STATUS during

n iPod operation

Operation buttons Function

(Press and release)

(Press and hold)

(Press and release)

(Press and hold)

8 9

RESTORER RESTORER TV POWER TV power on/standby (Default : SONY)

• Repeat playback (vpage72 “Repeat”)

• Random playback (vpage72 “Random”)

z1 When the menu screen is displayed, press

z2 When the menu screen is displayed, press

Playing an iPod

MENU Amp menu

Cursor operation /

uio p

ENTER

RETURN Return

6 7

3 2

TV INPUT Switch TV input (Default : SONY)

Auto search (cue, ui) /

Manual search (Press and hold, ui)

Enter / Pause

Stop

Page search

/ Character search

Browse / Remote mode switching

Manual search

(fast-reverse/fast-forward)

Playback / Pause Auto search (cue)

Pause

Stop

SEARCH, then press o (previous page) or p

(next page). To cancel, press ui or SEARCH twice.

SEARCH twice, then press o p to select the

ﬁrst letter you want to search mode.

• If it is not possible to search the list, “unsorted list.” is displayed.

To cancel, press ui or SEARCH.

If the list is not in alphabetical order, you may not be able to perform a character search.

Simple version Advanced version InformationBasic version

+ 93 hidden pages