Delonghi ECAM38X.7Y, ECAM38X.8Y, ECAM38X.9Y User guide

Download

Page 1

ECAM38X.7Y - ECAM38X.8Y - ECAM38X.9Y

BEAN TO CUP ESPRESSO

AND CAPPUCCINO

MACHINE

Instructions for Use

Instruction videos available at:

https://r.delonghi.com/video/

dinamica-plus

Page 2

A12

A13

B C

A10

A11

A22*

A21

A20

A19

A16

A14

A15

A17

A18

Page 3

Page 4

B C

C2 C1

C6 C3

C5 C4

READY

B1B8

Page 4

CONTENTS

1. INTRODUCTION ...........................................5

1.1 Letters in brackets .................................................... 5

1.2 Troubleshooting and repairs..................................... 5

2. DESCRIPTION ..............................................5

2.1 Description of the appliance (page 2 - A) ................. 5

2.2 Description of homepage (main screen) (page 3 - B) 5

2.3 Description of control panel (page 3 - C) .................. 5

2.4 Description of accessories (page 3 - D) ..................... 5

2.5 Description of milk carafe (page 3 - E) ...................... 5

3. SETTING UP THE APPLIANCE ........................5

4. TURNING THE APPLIANCE ON .......................6

5. TURNING THE APPLIANCE OFF ......................6

5.1 Switching o for extended periods: ......................... 7

6. SETTINGS MENU .......................................... 7

6.1 Access the menu ...................................................... 7

6.2 Exit the menu ........................................................... 7

6.3 Rinse ....................................................................... 7

6.4 Descaling ................................................................ 7

6.5 Cleaning the carafe .................................................. 7

6.6 MY programme ....................................................... 7

6.7 Coee temperature .................................................7

6.8 Drinks settings ........................................................ 7

6.9 Water lter ..............................................................7

6.10 Water hardness .......................................................7

6.11 Auto-o (standby) .................................................. 7

6.12 Set language ........................................................... 8

6.13 Energy saving ......................................................... 8

6.14 Audible warning ...................................................... 8

6.15 Customise prole ..................................................... 8

6.16 Statistics .................................................................. 8

6.17 Machine info ............................................................ 8

6.18 Default values ......................................................... 8

7. MAKING COFFEE ..........................................8

7.1 Making coee using coee beans ............................ 8

7.2 Selecting the coee intensity ................................... 9

7.3 Selecting the coee quantity ................................... 9

7.4 Making coee using pre-ground coee.................... 9

7.5 Adjusting the coee mill ........................................ 10

7.6 Tips for a hotter coee ........................................... 10

8. COFFEE POT ............................................... 10

9. MAKING HOT MILKBASED DRINKS ............ 11

9.2 Filling and attaching the milk carafe ...................... 11

9.3 Adjusting the amount of froth ...............................12

9.4 Making cappuccinos and milk-based drinks

automatically ......................................................... 12

9.5 Cleaning the milk carafe after use ......................... 12

10. DELIVERING HOT WATER ............................ 13

11. CUSTOMISING DRINKS ............................. 13

12. CLEANING ................................................ 14

12.1 Cleaning the machine ............................................ 14

12.2 Cleaning the internal circuit ................................... 14

12.3 Cleaning the coee grounds container ................... 14

12.4 Cleaning the drip tray and condensate tray ............ 14

12.5 Cleaning the inside of the machine ....................... 15

12.6 Cleaning the water tank ......................................... 15

12.7 Cleaning the coee spouts ..................................... 15

12.8 Cleaning the pre-ground coee funnel .................. 15

12.9 Cleaning the infuser ............................................... 15

12.10 Cleaning the milk carafe ........................................ 16

12.11 Cleaning the hot water nozzle ................................ 17

13. DESCALING ............................................... 17

14. SETTING WATER HARDNESS ...................... 18

14.1 Measuring water hardness ..................................... 18

14.2 Setting water hardness ......................................... 18

15. WATER SOFTENER FILTER .......................... 19

15.1 Installing the lter ................................................. 19

15.2 Replacing the lter................................................. 19

15.3 Removing the lter ................................................ 20

16. TECHNICAL DATA ....................................... 20

16.1 Tips for Energy Saving ............................................ 20

17. DISPLAYED MESSAGES ...............................20

18. TROUBLESHOOTING .................................. 23

Page 5

1. INTRODUCTION

Thank you for choosing this bean to cup espresso and cappuccino machine. Take a few minutes to read these Instructions for Use. This will avoid all risks and damage to the appliance.

1.1 Letters in brackets

The letters in brackets refer to the legend in the description of the appliance on pages 2-3.

1.2 Troubleshooting and repairs

In the event of problems, rst try and resolve them by reading the information given in sections "17. Displayed messages" and "18. Troubleshooting". If this does not resolve the problem or you require further information, you should consult Customer Services by calling the number given on the annexed "Customer Service" sheet. If your country is not among those listed on the sheet, call the number given in the guarantee. If repairs are required, contact De’Longhi customer services only. The addresses are given in the guarantee certicate provided with the machine.

2. DESCRIPTION

2.1 Description of the appliance (page 2 - A)

A1. Beans container lid A2. Pre-ground coee funnel lid A3. Beans container A4. Pre-ground coee funnel A5. Grinding adjustment dial A6. Cup shelf A7. button: to turn the appliance on and o (standby) A8. Hot water/steam connection nozzle A9. Coee spouts (adjustable height) A10. Condensate tray A11. Coee grounds container A12. Cup tray A13. Drip tray water level indicator A14. Drip tray grille A15. Drip tray A16. Water tank lid A17. Water tank A18. Water softener lter housing A19. Infuser door A20. Infuser A21. Power cord A22. Main switch (certain models only)

2.2 Description of homepage (main screen) (page

3 - B)

B1. Energy Saving active symbol B2. Intensity selected

B3. Directly selected drinks B4. Scroll arrow B5. Quantity selected B6. Descale alarm B7. Milk carafe cleaning alarm B8. Spent lter alarm

2.3 Description of control panel (page 3 - C)

C1. Coee drinks menu C2. Milk drinks menu

C3. : appliance settings menu

C4.

C5. : drink intensity selection

C6. : drink quantity selection

: prole selection menu

2.4 Description of accessories (page 3 - D)

D1. "Total Hardness Test" strip D2. Pre-ground coee measure D3. Descaler (certain models only) D4. Water softener lter (certain models only) D5. Cleaning brush (certain models only) D6. Hot water spout

2.5 Description of milk carafe (page 3 - E)

E1. Froth adjustment and CLEAN dial E2. Milk carafe lid E3. Milk carafe E4. Milk intake tube E5. Frothed milk spout (adjustable)

SETTING UP THE APPLIANCE

Please note!

• The rst time you use the machine, the water circuit is empty and the appliance could be very noisy. The noise becomes less as the circuit lls.

• Coee has been used to factory test the appliance and it is therefore completely normal for there to be traces of coee in the mill. The machine is, however, guaranteed new.

• You should customise water hardness as soon as possible following the instructions in section "14. Setting water hardness".

1. Plug the appliance into the mains socket and, in the case of models with main switch «A22», make sure it is set to the I position “g. 1”.

Page 6

in section "15. Water softener lter". If your model is not provided with a lter, you can request one from De'Longhi customer services.

2. To select the language of the display, press and hold until the required language appears, then press the ag corresponding to the language.

Now follow the instructions indicated on the display of the appliance:

3. Remove the water tank (A17) (g. 2), ll to the MAX line (marked on the tank) with fresh water (g. 3), then return it to its position (g. 4);

332

4. Make sure the hot water spout (D6) is attached to the connection nozzle (A8) (g. 5) and place a container of at least 200 ml capacity under the coee spouts (A9) and hot water spout (g. 6);

5. Press to conrm. The appliance delivers water from the spout.

6. At the end of delivery, the appliance proceeds with heating by performing a rinse cycle, delivering hot water from the coee spouts.

The coee machine is now ready for normal use.

Please note!

• The rst time the appliance is used, it will be necessary to make 4-5 cappuccinos before the drink in the cup tastes as it should. It is normal to hear the noise of boiling water at rst: the noise will become less with subsequent use.

• To improve the performance of your appliance, we recommend installing a water softener lter (D4) as described

4. TURNING THE APPLIANCE ON

Please note! Models with main switch only «A22» Before turn- ing the appliance on, make sure the main switch on the back of the appliance is pressed (g. 1). Each time the appliance is turned on, it performs an automatic preheat and rinse cycle which cannot be interrupted. The appliance is not ready for use until the cycle has been completed.

1. To turn the appliance on, press the button (A7)(g.

7): the preheat sequence now starts.

2. Once the appliance has heated up it performs a rinse cycle, during which hot water is delivered from the coee spout (A9); in addition to heating up the boiler, this also heats the internal circuits by circulating hot water.

The appliance is ready for use when the main screen (homepage) appears.

5. TURNING THE APPLIANCE OFF

Whenever the machine is turned o after being used to make coee, it performs an automatic rinse cycle.

Danger of scalding!

During rinsing, a little hot water ows from the coee spouts (A9) . Take care to avoid contact with splashes of water. To

Page 7

avoid the need for frequent emptying of the drip tray , place a container under the spouts to collect the rinse water.

1. To turn the appliance o, press the button (A7) (g.

7).

2. If provided for, the appliance performs a rinse cycle then goes o (stand-by).

5.1 Switching o for extended periods:

If the machine is not going to be used for any length of time (e.g. holidays, periods of absence), proceed as follows:

• turn the appliance o by pressing the button (g. 7);

• empty out and clean the grounds container (A11) and the water tank (A17);

• unplug the power cord (A7) from the socket.

Please note:

When turning the machine on again, ll the water tank and, before making any kind of drink, run 3 rinse cycles as indicated in section “6.3 Rinsing.”

Important!

Always turn the appliance o with the button (standby) or, in the case of models having a main switch, set the switch to the 0 position, before unplugging from the mains socket.

6. SETTINGS MENU

6.1 Access the menu

1. Press the button(C3) to enter the menu;

2. Scroll through the menu items by pressing until the required item is displayed;

3. Press the menu item you want to select.

6.2 Exit the menu

Having made the desired adjustments, press until the homepage reappears.

6.3 Rinse

Use this function to deliver hot water from the coee spouts (A9) to clean and heat the appliance’s internal circuit.

1. Place a container of at least 100ml capacity under the coffee spouts (g. 8).

2. A few seconds after "RINSE" has been selected, hot water is delivered from the coee spouts to clean and heat the appliance’s internal circuit (g. 8).

3. To stop rinsing, press or wait for rinsing to stop automatically.

Please note

After cleaning, it is normal for the grounds container (A11) to contain water.

6.4 Descaling

For instructions on descaling, see section "13. Descaling".

6.5 Cleaning the carafe

For instructions on cleaning the milk carafe (E3), see section"15. Water softener lter".

6.6 MY programme .

Pressing the button, users can choose under which prole to customize their drink (see section "11. Customizing drinks").

6.7 Coee temperature

To change the temperature of the water used to make the coffee, proceed as follows:

1. Press "COFFEE TEMPERATURE"

pear on the display (the current value is underlined);

2. Press the value you want to set (LOW, MEDIUM, HIGH).

Please note:

Varying the temperature has most eect for long drinks.

. The selectable values ap-

6.8 Drinks settings

In this section, you can consult your customised settings and, if you wish, reset the default values for each drink.

1. Once in the settings menu, press "DRINK SETTINGS". The values for the rst drink appear on the display;

2. The values are displayed on vertical bars. The default value

is indicated by the symbol, while the current value is highlighted by the solid part of the vertical bar;

3. To scroll and display the drinks, press ;

4. To reset the default values for the drink displayed, press

;

5. "CONFIRM RESET?": to conrm, press (to cancel, press );

6. ""DEFAULT VALUES SET": press .

The drink has been reset to the default values. Proceed with the other drinks or go back to the homepage by pressing

twice.

6.9 Water lter

For instructions on how to install the lter (D4), see section "15. Water softener lter".

6.10 Water hardness

For instructions on setting water hardness, see section "14. Setting water hardness".

6.11 Auto-o (standby)

Auto-o can be set so that if the appliance is not being used, it will switch o after 15 or 30 minutes or after 1 or 3 hours have elapsed. To programme Auto-o, proceed as follows:

1. Press "AUTO-OFF";

Page 8

2. Select the required time interval by pressing the selection arrows (increase) or (decrease);

3. To conrm, press .

Auto-o is now programmed.

6.12 Set language

To modify the language of the display, proceed as follows:

1. Press "SET LANGUAGE";

2. Press the ag corresponding to the language you want to set (press to display all the languages available).

6.13 Energy saving

Use this function to enable or disable energy saving. When enabled, the function reduces energy consumption in compliance with European regulations. To disable or enable "Energy Saving", proceed as follows:

Press "ENERGY SAVING" to disable ( ) or enable ( ) the function; The corresponding symbol (B1) appears on the top bar of the homepage to indicate that the function has been enabled.

Please note:

If energy saving is active, you may have to wait a few seconds before delivery.

6.14 Audible warning

This enables or disables the beep emitted by the machine each time an icon is pressed or an accessory is inserted/removed. To disable or enable the beep, proceed as follows:

1. Press "BEEP" to disable ( ) or enable ( ) the function;

6.15 Customise prole

To customise the icon of the current prole, proceed as follows:

1. Press "CUSTOMISE PROFILE";

2. Select the desired icon (press to display all the available icons).

6.16 Statistics

This displays statistics relating to the machine. To view the statistics, proceed as follows: Press "STATISTICS" and check all the statistics by scrolling through the items using .

6.17 Machine info

This displays the serial number of the machine. To view the number, press "MACHINE INFO". (press to cancel the operation).

6.18 Default values

This function resets all menu settings and all user customizations, restoring the factory default values (with the exception of the language, which remains as set, and the statistics). To reset the default values, proceed as follows:

1. Press "DEFAULT VALUES": the display shows the prompt "RESET FACTORY DEFAULT VALUES": press to conrm (or press to cancel the operation);

2. “FACTORY DEFAULT VALUES SET”: press to conrm.

7. MAKING COFFEE

7.1 Making coee using coee beans

Important!

Do not use green, caramelized or candied coee beans as they could stick to the coee grinder and make it unusable.

1. Fill the container (A3) with coee beans (g. 9);

8 109

2. Place a cup under the coee spouts (A9) (g.8);

3. Lower the spouts as near as possible to the cup (g. 10). This makes a creamier coee;

4. Select the required coee drink:

Recipe Quantity Program-

mable quantity

ESPRESSO

COFFEE

LONG

2X ESPRESSO

≃ 40 ml from ≃20 to

≃ 180ml

≃ 180 ml from ≃100

to ≃240ml

≃ 160 ml from ≃115

to ≃250 ml

≃ 40 ml

x 2 cups

Intensity predened

Page 9

ESPRESSO LUNGO

SHORT

DOPPIO+

≃ 120 ml ≃ 20 -180

≃ 30 ml ≃ 20-40 ml

≃ 120 ml ≃ 80-180 ml

7.2 Selecting the coee intensity

Press the button C5):

Predened or programmed intensity

EXTRA LIGHT

COFFEE POT

ICED COFFEE

VERLÄN GERTER

AMERICANO

HOT WATER

5. Preparation begins. An image of the selected drink appears on the display, together with a progress bar which gradually lls as preparation progresses.

Please note:

• Press on the scroll arrows ;to view all drinks.

• You can prepare 2 cups of ESPRESSO coee at the same

time by pressing "2X " during preparation of 1 ESPRESSO (the image is displayed for a few seconds at the start of preparation).

• While the machine is making coee, delivery can be interrupted at any moment by pressing .

• Immediately following delivery, to increase the quantity of coee delivered, press . : when the required quantity is reached, press or .

Once the preparation has been completed, the machine is ready for use again.

Please note!

• Various alarm messages could be displayed while using the appliance (FILL TANK, EMPTY GROUNDS CONTAINER, ETC.). Their meaning is explained in section "17. Displayed messages".

• For hotter coee, see section "7.6 Tips for a hotter coee".

• If the coee emerges drop-by-drop, too weak and not creamy enough, or too cold, read the tips in section "7.5 Adjusting the coee mill" and in section "18. Troubleshooting"

• Preparation of each coee can be customised (see section "11. Customising drinks").

≃ 250 ml -

≃ 100 ml -

≃ 80 ml ≃ 50-480 ml

≃ 150 ml ≃70- 480 ml

≃ 250 ml ≃ 20-420 ml

LIGHT

MEDIUM

STRONG

X-STRONG

(see "7.4 Making coee using pre-ground coee")

After delivering the drink, the intensity setting is reset to the

value.

7.3 Selecting the coee quantity

Press the button (C6):

After delivering the drink, the quantity setting is reset to the

value

7.4

Making coee using pre-ground coee

Important!

• Never add pre-ground coee when the machine is o, or it could spread through and soil the inside of the machine. This could damage the machine.

• Never use more than 1 level measure (D2) as it could soil the inside of the coee machine or block the funnel (A4).

D1. When using pre-ground coee, only one cup can be made

at a time.

1. Press the button (C5) repeatedly until the message “ ” (pre-ground) is displayed.

2. Select the required coee drink:

• ESPRESSO

Predened or programmed quantity (see table in section "11. Customising drinks"

SMALL SIZE

MEDIUM SIZE

LARGE SIZE

X-LARGE SIZE

Page 10

• LONG

• COFFEE

• 2X ESPRESSO

• ESPRESSO LUNGO

• SHORT

• DOPPIO+

• VERLÄNGERTER

• AMERICANO

3. "ADD GROUND COFFEE MAX. ONE MEASURE": open the lid of the pre-ground coee funnel (A2).

4. Make sure the funnel (A4) is not blocked, then add one level measure of pre-ground coee (g. 11).

1110

5. Place a cup under the coee spouts (A9) (g. 10).

6. Press : preparation begins. An image of the selected drink appears on the display, together with a progress bar which gradually lls as preparation progresses.

Once the preparation has been completed, the machine is ready for use again.

Important! Making LONG coee: Halfway through preparation, the machine requests a further level measure of pre-ground coee. Proceed, then press

7.5 Adjusting the coee mill

During the initial stages of use, there is no need to adjust the coee mill as the factory setting will ensure that the coee is brewed correctly. However, if after the initial period of use coee emerges either too weak or not creamy enough, or the delivery is too slow (drop by drop), this can be corrected by adjusting the grinding adjustment dial (A5) (g. 12).

Please note!

The adjustment dial must be turned only when the coee mill is in operation during the initial step of coee preparation.

If the coee is delivered too slowly or not at all, turn one click clockwise towards 7. For fuller bodied creamier coee, turn one click anticlockwise towards 1 (do not turn more than one click at a time

otherwise the coee could be delivered a drop at a time). The eect of the adjustment will be noticed only after making a further 2 cups of coee, at least. If this adjustment does not produce the desired result, turn the dial another click.

7.6 Tips for a hotter coee

To make a hotter coee, proceed as follows:

• run a rinse cycle by selecting the "Rinse" function (section

"6.3 Rinse ");

• warm the cups with hot water using the hot water function

(see section "10. Delivering hot water");

• increase the coee temperature setting (section "6.7 Cof-

fee temperature "). Varying the temperature is most eective with long drinks.

8. COFFEE POT

Based on espresso coee, the recipe of this drink is light and balanced, featuring a nely frothed top, ideal to share in company.

Optional accessory in certain models:

Coee Pot (Capacity: 750ml)

Model: AS00006179

EAN: 8004399333642

To make the drink, proceed as follows:

Page 11

N° cups selected Quantity (ml) *

≃ 250

≃ 500

≃ 750

(*) The quantities indicated are approximate and may vary according to the type of coee.

1. Press "COFFEE POT";

2. Select the intensity and the number of cups;

3. Press to move on to the next step.

4. "FILL TANK AND BEANS CONTAINER": ll the water tank (A17) and the beans container (A3) (g. 9) as indicated on the display. Make sure there is sucient water and coee for the drinks to be prepared, then press .

5. "PLACE POT UNDER SPOUTS". Position a pot under the coee spouts (A9): when choosing the pot to use, bear in mind the quantity to be delivered.

6. Press : After a few seconds, preparation begins automatically and an image of the selected drink appears on the display, together with a progress bar which gradually lls as preparation progresses.

Once the preparation has been completed, the machine is ready for use again.

Please note:

• : press to interrupt preparation completely

and go back to the homepage.

• the temperature of the milk or vegetable drink used (for best results, always use milk or vegetable drink straight from the fridge + 5°C);

• type of milk or vegetable drink;

• the brand used;

• ingredients and nutritional values.

Cow's milk

Whole (fat >3,5%)

Semi-skimmed (fat between 1.5 and 1.8%)

Skimmed (fat <0.5%)

Vegetable drinks

Soya

Almond

Oatmeal

✓

✓ ✓ ✓

9.2 Filling and attaching the milk carafe

1. Remove the lid (E2) (g. 13);

2. Fill the milk carafe (E3) with a sucient quantity of milk, not exceeding the MAX level marked on the carafe (g. 14). Each mark on the side of the carafe corresponds to about 100 ml of milk;

SAFETY WARNING:

After making a pot of coee, leave the machine to cool for 5 minutes before making another drink. Risk of overheating!

MAKING HOT MILKBASED DRINKS

Please note!

To avoid the preparation of milk with poor froth or large bubbles, always clean the milk container lid (E2) and hot water connection nozzle (A8) as described in sections "9.5 Cleaning the milk carafe after use", "12.10 Cleaning the milk carafe" and "12.11 Cleaning the hot water nozzle".

9.1 Which milk to use?

The quality of the froth will vary depending on:

Please note!

• For a denser and more evenly distributed froth, always use skimmed or partially skimmed milk at refrigerator temperature (about 5 °C).

• If “Energy Saving” mode is enabled (see section ), there may be a delay of a few seconds before the drink is delivered.

3. Make sure the milk intake tube (E4) is secured correctly to the socket on the underside of the milk carafe lid (g. 15);

Page 12

MILK

4. Reposition the lid on the milk carafe;

5. Remove the hot water spout (D6);

6. Attach the milk carafe (E) to the connection nozzle (A8) and push fully home (g. 16). The machine emits a beep (if the beep function is enabled);

7. Place a suciently large cup under the coee spouts (A9) and the frothed milk spout (E5). Adjust the length of the milk spout. To move it nearer the cup, simply pull it downwards (g. 17).

16 17

8. Follow the instructions below for each function.

9.3 Adjusting the amount of froth

Turn the froth adjustment dial (E1), to adjust the amount of froth on the milk delivered when making cappuccinos and other milk-based drinks.

Dial position

Description Recommended for…

DELICATE HOT MILK (not frothed) /

CAFFELATTE/ CAFE' CON LECHE /CAFE' AU LAIT

CREAMY LATTE MACCHIATO/

FLAT WHITE / CORTADO

DENSE CAPPUCCINO / CAPPUCCI

NO+ / CAPPUCCINO MIX / ESPRESSO MACCHIATO / HOT MILK (frothed)

9.4 Making cappuccinos and milk-based drinks automatically

1. Fill the milk carafe (E) and attach it as described above.

2. Select the required drink:

• CAPPUCCINO

• LATTE MACCHIATO

• HOT MILK

• CAPPUCCINO+

• CAPPUCCINO MIX

• CAFFELATTE

• FLAT WHITE

• ESPRESSO MACCHIATO

• CAFE' CON LECHE

• CAFE' AU LAIT

• CORTADO

• GALAO

3. A message on the display recommends setting the froth

adjustment dial (E1) according to the froth required by the original recipe: turn the dial on the lid of the milk carafe.

4. After a few seconds, preparation begins automatically and

an image of the selected drink appears on the display, together with a progress bar which gradually lls as prepa-

ration progresses. Once the preparation has been completed, the machine is ready for use again.

Please note! general indications when preparing all milkbased drinks

• : press to stop preparation completely and go

back to the homepage.

•

move on to the next delivery (if applicable) to complete the

drink.

• Preparation of each milk-based drink can be customized

(see section "11. Customising drinks").

• Do not leave the milk container out of the refrigerator for

long periods; the warmer the milk (5 °C is ideal), the poorer

the quality of the froth will be.

: press to interrupt milk or coee delivery and

9.5 Cleaning the milk carafe after use

Every time that milk functions are used, the message "TURN ADJUSTMENT DIAL TO CLEAN POSITION" appears on the display and the lid of the milk carafe must be cleaned:

Page 13

1. Leave the milk carafe in the machine (there is no need to empty the carafe);

2. Place a cup or other recipient under the frothed milk spout;

3. Turn the froth adjustment dial (E1) to "CLEAN" (g. 18). "CLEANING UNDERWAY RECIPIENT UNDER SPOUT" appears on the display together with a bar which gradually lls as cleaning progresses. Steam mixed with hot water comes out of the frothed milk spout (g. 19). Cleaning stops automatically;

18 19

4. Turn the dial back to one of the froth selections;

5. Remove the milk carafe and always clean the hot water connection nozzle (A8) with a sponge (g. 20).

carafe, return it straight away to the fridge and clean all components, proceeding as described in heading “12.10. Cleaning the milk carafe”

Following preparation of milk-based drinks — general notes:

• If the milk carafe is left out of the refrigerator for more than 30 minutes, disassemble and clean all components, proceeding as described in section “12.10. Cleaning the milk carafe”.

• the carafe cannot be kept in the refrigerator for more than 2 days.

• If the milk carafe is not cleaned, the symbol (B7) appears on the display as a reminder that cleaning is required.

• In certain cases, the machine will need to heat up before cleaning can take place.

10. DELIVERING HOT WATER

1. Make sure the hot water spout (D6) is attached correctly to the hot water connection nozzle (A8);

2. Place a cup under the spout;

3. Press “HOT WATER”; The corresponding image appears on the display, together with a progress bar which lls gradually as preparation proceeds;

4. The machine delivers hot water, then delivery stops automatically. To interrupt hot water delivery manually, press

Please note!

• If "Energy Saving" mode is active, there may be a delay of a few seconds before the hot water is delivered.

• Preparation of hot water can be customised (see section "11. Customising drinks"").

20 21

Where various drinks are prepared in succession:

• Proceed with cleaning of the carafe after the nal preparation.

After multiple preparations, the milk carafe is empty or the milk that remains is not enough to make further drinks

• Having carried out the cleaning step with the froth adjustment dial (E1) set to the “CLEAN” position, disassemble the milk carafe and clean all components, proceeding as described in heading “12.10. Cleaning the milk carafe”

After multiple preparations, there is enough milk left in the carafe to make further drinks

• Having carried out the cleaning step with the froth adjustment dial (E1) set to the “CLEAN” position, remove the milk

11. CUSTOMISING DRINKS

The intensity (when required) and the quantity of drinks can be customised.

To access the function, press the button (C3). Scroll the

menu and select .

1. Select the required prole;

2. Select the drink to be customise: the requisite accessories must be tted;

3. For coee drinks only, select the required intensity by pressing “- “ o “+” then press ;

4. Preparation begins and the display shows the drink with a vertical bar. The star alongside the bar represents the current quantity;

5. When the amount reaches the minimum programmable quantity, the message will be displayed;

6. Press when the required quantity in the cup is reached;

Page 14

7. Press to save (or to cancel). The appliance conrms if the values have been saved or not (depending on the previous selection). Press . The appliance goes back to the homepage.

Please note!

• Milk-based drinks: the intensity of the coee is saved

rst, followed by the quantity of milk, then the quantity of coee;

• Hot water: the appliance delivers hot water. Press to save the required quantity.

• Press to exit programming. The values will not

be saved.

12. CLEANING

12.1 Cleaning the machine

The following parts of the machine must be cleaned periodically:

• internal circuit;

• coee grounds container (A11);

• drip tray (A15), condensate tray (A10), drip tray grille (A14)

and tray full indicator (A13);

• water tank (A17);

• coee spouts (A9);

• pre-ground coee funnel (A4);

• infuser (A20), accessible after opening the infuser ap

(A19);

• milk carafe (E);

• hot water connection nozzle (A8);

• control panel (C).

Important!

• Do not use solvents, abrasive detergents or alcohol to

clean the machine. With De’Longhi superautomatic coee machines, no chemical additives are required for cleaning purposes.

• None of the components of the appliance can be washed

in a dishwasher: the only exceptions are the drip tray grille (A14), the milk carafe (E) and the drip tray (A15).

dishwasher safe hand wash only

12.2 Cleaning the internal circuit

If the appliance is not used for more than 3/4 days, it is strongly advisable when switching on again, before using it, to empty the water and ll it with fresh drinking water, then run 2/3 rinse cycles selecting the “Rinse” function (sec tion "6.3 Rinse ");

Please note!

Water may nd its way into the grounds container (A11) during the above rinse procedure: this is quite normal.

12.3 Cleaning the coee grounds container

When "EMPTY GROUNDS CONTAINER" appears on the display, the grounds container must be emptied and cleaned. Until the the grounds container (A11) is repositioned, the machine cannot make coee. Even if the grounds container is not full, the "Empty" warning message will be displayed 72 hours after the rst coee has been prepared. For the 72 hours to be calculated correctly, the machine must never be turned o with the main switch (A22) (if the model has one).

Important! Danger of scalding

If several milk-based drinks are prepared one after the other, the metal cup tray (A12) becomes hot. Wait for it to cool down before touching it and handle it from the front only. To clean (with the machine on):

1. Remove the drip tray (A15) and the grounds container (A11)(g. 21).

2. Empty the drip tray and grounds container and clean thoroughly to remove all residues left on the bottom. This can be done using the spatula on the brush (D5) provided.

3. Check the condensate tray (A10) (colour red) and empty if necessary.

4. Put the drip tray complete with grille and grounds container back in the appliance.

Important!

When removing the drip tray, the coee grounds container must always be emptied, even if it has not lled up noticeably. If this is not done, it can happen that when further coees are prepared, the grounds container will ll up more than expected and clog the machine.

drip tray grille (A14) cup tray (A12)

Milk carafe (E) water tank (A17)

drip tray (A15)

• Do not use metal objects to remove encrustations or coee deposits as they could scratch metal or plastic surfaces.

removable infuser (A20)

coee grounds container (A11)

12.4 Cleaning the drip tray and condensate tray

Important!

The drip tray (A15) is tted with a level indicator (A13) (colour red) showing the amount of water it contains (g. 22). Before the indicator protrudes from the cup tray, the drip tray (A12) must be emptied and cleaned, otherwise the water may overow the edge and damage the appliance, the surface it rests on or the surrounding area.

Page 15

To remove the drip tray, proceed as follows:

1. Remove the drip tray and the coee grounds container (A11) (g. 21);

2. Remove the cup tray (A12) and drip tray grille (A14), then empty the drip tray and grounds container and wash all components.

3. Check the condensate tray, (A10) coloured red, and empty if necessary;

4. Put the drip tray, complete with grille, tray and grounds container, back in the appliance.

Important!

12.5 Cleaning the inside of the machine

Danger of electric shock!

Before cleaning internal parts, the machine must be turned o (see section "5. Turning the appliance o") and unplugged from the mains power supply. Never immerse the machine in water.

1. Check periodically (about once a month) that the inside of the appliance (accessible after removing the drip tray) and the coee grounds container (A15) are not dirty. If necessary, remove coee deposits with the brush (D5) supplied and a sponge.

2. Remove all residues with a vacuum cleaner (g. 23).

3. Empty the water tank and clean with a damp cloth and a little washing up liquid. Rinse thoroughly with water.

4. Reinstate the lter (if installed, ll the tank with fresh water up to the MAX level and reposition the tank;

5. (Models with water softener lter only) Release around 100ml of hot water to reactivate the lter.

Please note:

If the appliance is not used for more than 3-4 days, it is advisable to clean the tank as described above.

12.7 Cleaning the coee spouts

1. Clean the coee spouts (A9) periodically with a sponge or

cloth (g. 24A);

2. Check that the holes in the coee spout are not blocked.

If necessary, remove coee deposits with a toothpick (g. 24B).

12.8 Cleaning the pre-ground coee funnel

The pre-ground coee funnel (A4) requires cleaning periodically (about once a month). Proceed as follows:

1. Turn the machine o (see section "5. Turning the appliance

o";

2. Open the funnel ap (A2);

3. Clean the funnel with the brush provided (D5) (if included);

4. Close the ap.

Important!

After cleaning, make sure that no object or accessory has been left in the funnel: the presence of foreign matter in the funnel during operation could cause damage to the machine.

12.9 Cleaning the infuser

The infuser (A20) must be cleaned at least once a month.

Important!

The infuser cannot be removed while the machine is on.

1. Make sure the procedure for turning o the machine has

been completed correctly o (see section "5. Turning the appliance o");

2. Remove the water tank (A17) (g. 2);

3. Open the ap (A19) (g. 25) on the right hand side;

2322

3. Put the drip tray, complete with grille, tray and grounds container, back in the appliance

12.6 Cleaning the water tank

Periodically (about once a month) and whenever the water softener lter (D4) is replaced (if installed), be sure to clean the water tank (A17).

1. Remove the water tank (g. 2);

2. Remove the lter (if installed) and rinse with running

water;

24A

24B

PUSH

Page 16

32A 32B

Press the two coloured release buttons inwards and at the same time pull the infuser outwards (g. 26);

5. Immerse the infuser in water for about 5 minutes, then rinse under the tap;

Important!

RINSE WITH WATER ONLY NO DETERGENTS  NO DISHWASHER

6. Do not use detergents when cleaning the infuser, as they could damage it.

7. Use the brush (D5) (if included), to remove any coee residues left in the infuser housing, visible behind the infuser ap (A19);

8. After cleaning, replace the infuser by sliding it into its housing (g. 27), then apply pressure to the PUSH symbol until it clicks into place;

PUSH

26 27

Please note!

If the infuser is dicult to insert, before insertion, adapt it to the right size by pressing the two levers shown in g. 28.

2. Remove the milk spout and extension (E5), and the intake tube (E4) (g. 30);

3. Turn the froth adjustment dial (E1) anticlockwise to the "INSERT" position (g. 31) and pull o upwards;

4. Wash in a dishwasher (recommended) or by hand as indicated below:

• In a dishwasher: Rinse all the above components and the milk carafe under hot running drinking water (at least 40 °C), then place them in the top basket of the dishwasher and run a wash programme at 50 °C, e.g. standard ECO.

• By hand Rinse all the components and the milk carafe thoroughly with hot running drinking water (at least 40 °C) to remove all visible milk residues; make sure to direct the water through the holes in the lid (g. 32A). Then immerse all the components in hot drinking water (at least 40 °C) and washing up liquid for at least 30 minutes. Rinse all the components described above thoroughly under hot drinking water, rubbing each one individually between ngers and thumbs.

PUSH

9. Once inserted, make sure the two coloured buttons have snapped out (g. 29);

10. Close the infuser ap;

11. Reposition the water tank in the machine.

12.10 Cleaning the milk carafe

Clean the milk carafe (E) after each use, as described below:

1. Remove the lid (E2);

5. Make sure that there are no milk residues left in the recess and the channel on the under scrape the channel clean with a toothpick (g. 32B);

6. Check that the intake tube and spout are not clogged with milk residues;

7. Dry all the components with a clean dry cloth;

8. Reassemble all the lid components;

side of the dial: if necessary

Page 17

9. Ret the lid to the milk carafe.

Please note:

The machine will give a reminder each week of the need for thorough cleaning of the milk carafe, indicating the correct procedure.

12.11 Cleaning the hot water nozzle

Clean the nozzle (A8) every time that milk is prepared, using a sponge to remove milk residues from the gaskets (g. 20).

13. DESCALING

Important!

•

Before use, read the instructions and the labelling relative to the descaler product, which are indicated on the pack ed with certain models and/or available for purchase from authorized service centres)

• Use De’Longhi descaler only. Using unsuitable descaler and/or performing descaling incorrectly may result in faults not covered by the manufacturer’s guarantee.

• Descaler can damage delicate surfaces. If the product is accidentally spilt, dry immediately.

To descale

Descaler De’Longhi “EcoDecalk” descaler

Container Recommended capacity: 2.0 litres

Time ~30min

(includ-

3. "REMOVE WATER FILTER" (g. 33): take out the water tank (A17), and remove the water softener lter (D4) (if pres-

ent).

4. Empty the water tank. Press ;

5. "DESCALER (LEVEL A) AND WATER (LEVEL B)". Pour the descaler into the tank up to level A (corresponding to a 100 ml pack) marked on the inner surface of the tank (g. 34), then add water (1 litre) up to level B (g. 35) and put the water tank back. Press ;

6. "EMPTY DRIP TRAY" (g. 21):

7. Remove, empty and replace the drip tray (A15) and grounds container (A11). Press ;

8. "POSITION 2l CONTAINER" "OK TO START":

Place an empty container of at least of 2 litres capacity under the hot water spout (D6) and coee spouts (A9) ;

Descale the appliance when "DESCALING NEEDED - PRESS OK TO START (~30min) appears on the display": To descale the appliance immediately, press and follow the operations from point 3. To delay descaling until later, press . The symbol

(B6) appears on the display as a reminder that the appliance needs descaling. (The message reappears every time the machine is turned on). To access the descaling menu:

1. Press the

Press "DESCALE" and follow the instructions on the

button

(C3) to enter the menu;

display;

34 35

Important! Danger of scalding

Hot water containing acid ows from the hot water and coee spouts. Accordingly, take care to avoid contact with this solution.

9. Press to conrm that the descaling solution has been added. "DESCALING UNDERWAY" "PLEASE WAIT" is displayed: the descale programme starts and the descaler solution comes out of the hot water spout and the coee spout; a succession of rinses is performed automatically at

Page 18

set intervals to remove the scale residues from inside the

coee machine;

After about 15 minutes, descaling stops;

10. "RINSE AND FILL WATER TANK UP TO MAX LEVEL" (g. 3): the appliance is now ready for a process of rinsing with fresh water. Empty the container used to collect the descaler solution. Remove the water tank from the machine, empty it and rinse under running water, then ll with clean water up to the MAX level and reposition it in the machine.

11. "POSITION 2l CONTAINER OK TO START RINSING": Reposition the container used to collect the descaler solution, empty, under the coee spouts and hot water spout and press ;

12. Hot water is delivered rst from the coee spouts then from the hot water spout and the message "RINSING UNDERWAY, PLEASE WAIT" is displayed;

13. When the water in the tank has run out, empty the container used to collect the rinsing water;

14. (If the lter is installed) "INSERT FILTER IN ITS HOUSING" (g. 36). Press and take out the water tank: replace the water softener lter, if removed previously;

15. "RINSE AND FILL WATER TANK UP TO MAX LEVEL" (g. 3): Fill the tank up to the MAX level with fresh water;

16. "INSERT WATER TANK" (g. 4): Reposition the water tank in the machine.

17. "POSITION 2l CONTAINER" "OK TO START RINSING": Reposition the container used to collect the descaler solution, empty, under the hot water spout (g. 8) and press

18. Hot water is delivered from the hot water/steam spout and the message "RINSING UNDERWAY, PLEASE WAIT" is displayed;

19. "EMPTY DRIP TRAY" (g. 21): At the end of the second rinse, empty the container used to collect the rinsing water, remove and empty the drip tray (A15) and grounds container (A11) and return them to the machine: press

;

20. "DESCALE COMPLETE": press ;

21. "FILL TANK WITH FRESH WATER": remove and top up the water tank with fresh water to the MAX level and put back in the machine.

The descaling cycle is now complete.

Please note!

• If the descaling cycle is not completed correctly (e.g. electrical power failure), when power is restored the appliance will prompt for the cycle to be completed.

• Water may nd its way into the grounds container (A11) during the descale cycle: this is quite normal.

• If the water tank has not been lled to the MAX level, at the end of descaling, the appliance requests a third rinse to guarantee that the descaler solution has been completely eliminated from the machine's internal circuits. Before starting the rinse, remember to empty the drip tray.

14.

SETTING WATER HARDNESS

The descaling alert is displayed after a period of operation established according to water hardness. The machine can also be programmed according to the actual hardness of the local water supply, so that the descaling procedure will be required less frequently.

14.1 Measuring water hardness

1. Remove the "TOTAL HARDNESS TEST" indicator strip (D1) from its pack.

2. Immerse the paper completely in a glass of water for about one second.

3. Remove the strip from the water and shake lightly. After about a minute, 1, 2, 3, or 4 red squares appear, depending on the hardness of the water. Each square corresponds to one level.

14.2 Setting water hardness

1. Access the menu as described in section "6.1 Access the menu";

2. Press "WATER HARDNESS";

3. Carry out the procedure described in the previous section to measure the water hardness;

4. "WATER HARDNESS" "CURRENT VALUE UNDERLINED": Press the level measured previously as indicated in the following table: (Level 1 = soft water; Level 4 = very hard water);

Indicator paper Water hardness

Level 1 - soft water

Level 2 - slightly hard water

Level 3 - hard water

Page 19

Indicator paper Water hardness

Level 4 - very hard water

5. Press to go back to the homepage. The machine is now reprogrammed with the new water hardness setting.

15. WATER SOFTENER FILTER

Certain models come equipped with a water softener lter (D4): if this is not the case with your model, we would advise purchasing one from a De’Longhi approved service centre. To use the lter correctly, follow the instructions below.

15.1 Installing the lter

1. Access the menu as described in section "6.1 Access the menu";

2. Press "WATER FILTER";

3. "TURN DATE INDICATOR TO NEXT 2 MONTHS" (g. 37): remove the new lter (D4) from the pack and turn the date indicator disk so that it shows the next 2 months of use. Press ;

37 38

Please note

IThe lter lasts about two months assuming normal use of the machine; if on the other hand the machine remains idle with the lter installed, it will not last more than three weeks, at most.

4. "RUN WATER INTO FILTER HOLE" "UNTIL IT COMES OUT" (g.

38): To activate the lter, run tap water through the central hole of the lter as shown in the gure until water comes out of the openings at the side for more than one minute. Press ;

5. Extract the tank (A17) from the appliance and ll with water.

6. "IMMERSE FILTER TO RELEASE AIR BUBBLES" (g. 39): Insert the lter in the water tank and immerse it completely

for about ten seconds, tilting it and applying light pressure so that the air bubbles can escape.

Press ;

7. "INSERT FILTER" "IN HOUSING": Insert the lter (D4) in the lter housing (g. 36) and press fully home. Press

;

8. "INSERT WATER TANK": Close the tank with the lid (A16), then reposition the tank in the machine (g. 4);

9. "POSITION 0.5L CONTAINER, OK TO ENABLE FILTER" (g.

6): Place the container under the hot water spout (D6) and press starts and stops automatically.

The lter is now activated and the machine can be used.

15.2 Replacing the lter

Replace the lter (D4) when "REPLACE WATER FILTER" "PRESS OK TO START" appears on the display: to replace immediately, press the preceding section. To delay replacement of the lter until later, press .

The symbol (B8) appears on the display as a reminder that the lter needs replacing. To replace, proceed as follows:

1. Access the menu as described in section "6.1 Access the menu";

2. Press "WATER FILTER";

3. Press "REPLACE FILTER"

4. First remove the tank (A17) and the spent lter, then follow the operations described in the previous section from point 3 onwards.

Please note!

After two months (see date indicator), or after 3 weeks if the appliance has not been used, the lter should be replaced even if the warning message has not yet been displayed.

: "HOT WATER PLEASE WAIT" delivery

and follow the instructions from point 5 of

Page 20

15.3 Removing the lter

If the intention is to use the appliance without the lter (D4), its removal must be indicated in the machine settings. Proceed as follows:

1. Remove the water tank (A17) and the spent lter;

2. Access the menu as described in section "6.1 Access the menu";

3. PRESS "WATER FILTER";

4. Press “REMOVE WATER FILTER” ;

5. “CONFIRM FILTER REMOVL": press

to go back to the settings menu);

6. "FILTER REMOVED": the change has been saved. Press

to go back to the homepage.

Please note!

After two months (see date indicator), or after 3 weeks if the appliance has not been used, the lter should be replaced even if the warning message has not yet been displayed.

(or press

16. TECHNICAL DATA

Voltage: 220-240 V~ 50-60 Hz max. 10 A Power: 1450 W Pressure: 1.5 MPa (15 bars) Water tank capacity: 1.8l Size LxDxH: 240x440x360 mm Cord length: 1250 mm Weight: 10 kg Beans container capacity: 300 g

16.1 Tips for Energy Saving

• To reduce energy consumption, after delivering one or more drinks, remove the container (E) or accessories.

• Set auto-o to 15 minutes (see section "6.11 Auto-o (standby) "):

• Enable Energy Saving (see paragraph "6.13 Energy saving

");

• When prompted by the machine, perform the descaling cycle (see section "13. Descaling").

17. DISPLAYED MESSAGES

DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY

FILL TANK WITH FRESH WATER

INSERT WATER TANK The tank

EMPTY GROUNDS CONTAINER The grounds container (A11) is full. Empty the grounds container and drip tray

Insucient water in the tank

(A17)

is not inserted or is inserted

incorrectly.

(A17)

. Fill the tank with water and/or insert it cor-

rectly, pushing it as far as it will go until it clicks into place.

Reposition the tank correctly and press fully home.

(A15) then clean and return them to the machine. Important: when removing the drip tray, the grounds container must always be emptied, however little it may have been lled. If this is not done, it can happen that the grounds container will ll up more than expected when further coees are prepared, causing the machine to clog.

Page 21

DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY

INSERT GROUNDS CONTAINER After cleaning, the grounds container

not been replaced.

ADD GROUND COFFEE MAX. ONE MEASURE

FILL BEANS CONTAINER

GROUND TOO FINE. ADJUST MILL

INSERT WATER SPOUT The hot water spout (D6) is not inserted or is

Preparation with pre-ground coee has been selected.

The coee beans have run out. Fill the beans container

The pre-ground coee funnel

The grinding is too ne, so that the coee is delivered too slowly or not at all.

If the water softener lter (D4) is present, an air bubble may have been released inside the circuit, obstructing delivery.

inserted incorrectly

(A11)

has

(A4)

is clogged. Empty the funnel with the aid of the brush

Remove the drip tray (A15) and insert the grounds container.

Make sure the funnel (A4) is not blocked, then add one level measure (D2) of pre-ground coee, press “OK” on the display and follow the instructions in section "7.4 Making coee using pre-ground coee".

(A4) (g. 10)

(D5) as described in section "12.8 Cleaning the pre-ground coee funnel".

Repeat coee delivery and turn the grinding adjustment dial wise towards "7" while the coee mill is in operation. If after making at least 2 coees delivery is still too slow, repeat the correction procedure, turning the grinding adjustment dial another click until delivery is correct (see section"7.5 Adjusting the coee mill"). If the problem persists, make sure the water tank (A17) is fully inserted.

Insert the hot water spout (D6) in the appliance and deliver a little water until the ow becomes regular. If the problem persists, remove the lter (see section 15.3 Removing the lter).

Insert the water spout and push fully home.

(A5) (g. 12)

one click clock-

INSERT MILK CARAFE The milk carafe (E) is missing or not correctly

in place.

INSERT INFUSER ASSEMBLY The infuser (A20) has not been replaced after

cleaning.

Insert the milk carafe and push fully home.

Insert the infuser as described in section "12.9 Cleaning the infuser".

Page 22

DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY

WATER CIRCUIT EMPTY PRESS OK TO START

PRESS OK TO CLEAN OR TURN DIAL

DESCALING INTERRUPTED PRESS NEXT TO CONTINUE

TURN MILK FROTH ADJUSTMENT DIAL TO CLEAN POSITION

TURN FROTH ADJUSTMENT DIAL

The water circuit is empty Press the selector corresponding to "OK" to

deliver water from the spout (D6) until it ows out normally. If the problem persists, make sure the water tank (A17) is fully inserted.

A new water softener lter has been inserted (D4)

The milk carafe has been inserted with the froth adjustment dial (E1) in the CLEAN position.

Descaling has been interrupted or has not been completed correctly.

Milk has been delivered recently and the tubes inside the milk carafe (E) must be cleaned.

A recipe with milk was requested Turn the dial to the required froth position.

Make sure the instructions for inserting the new lter have been followed correctly (section "15. Water softener lter"). If the problem persists, remove the lter (see section 15.3 Removing the lter).

To proceed with the CLEAN function, press the selector corresponding to the froth adjustment dial to one of the milk positions.

Press NEXT to resume the descaling procedure. For more information, see section "13. Descaling".

Turn the froth adjustment dial (E1) to CLEAN (g. 18).

"OK", or turn

SELECT A MILDER TASTE OR REDUCE COFFEE QUANTITY

DESCALING NEEDED PRESS OK TO START ~30MIN

REPLACE WATER FILTER PRESS OK TO START

Too much coee has been used. Select a milder taste by pressing the "INTEN-

SITY" button (C5) or reduce the quantity of ground coee (maximum 1 measure).

Indicates that the machine needs descaling. Press the selector corresponding to "OK" to

start descaling or "ESC" to descale later. The descaling procedure described in section "13. Descaling" needs to be performed.

The water softener lter (D4) is exhausted. Press the selector corresponding to "OK" to re-

place or remove the lter, or "ESC" to carry out the procedure later. Follow the instructions in section "15. Water softener lter".

Page 23

DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY

GENERAL ALARM: REFER TO USER MANUAL

Remember that the internal tubes of the milk

Reminds you the lter (D4) must be replaced. Replace the lter or remove it as described in

Energy saving is enabled. To disable energy saving, proceed as described

PLEASE WAIT The appliance is heating up to the optimum

CLEANING UNDERWAY PLEASE WAIT

The inside of the appliance is very dirty. Clean the inside of the appliance thoroughly,

as described in section "12. Cleaning". If the message is still displayed after cleaning, contact De'Longhi customer services and/or an authorized service centre.

Turn the froth adjustment dial (E1) to CLEAN

carafe (E) must be cleaned.

The machine must be descaled. The descaling procedure needs to be carried

temperature

The appliance has detected impurities in its internal circuits.

(g. 18).

section "15. Water softener lter".

out without delay, see section "13. Descaling".

in section "6.13 Energy saving ".

Wait for the appliance to be ready again and reselect the required drink. If the problem persists, contact De'Longhi Customer Services.

18. TROUBLESHOOTING

Possible malfunctions of the machine are listed below. If the problem cannot be resolved as described, contact Customer Service.

PROBLEM POSSIBLE CAUSE REMEDY

The appliance does not come on. It is not plugged into the mains socket. Plug into the mains socket (g. 1).

When present, make sure the main switch «A22» is on.

The coee is not hot. The cups were not preheated. Warm the cups by rinsing them with hot water

The internal circuits of the appliance have cooled down because 2/3 minutes have elapsed since the last coee was made.

Coee temperature setting too low.

The machine needs descaling

Press the main switch to the I position «g. 1».

(Please note: the hot water function can be used).

Before making the coee, heat the infuser by rinsing using the rinse function "6.3 Rinse "

Set a hotter coee temperature in the menu (see

section Please note: Varying the temperature has most eect for long drinks.

Proceed as described in section "13. Descaling". Next, check the water hardness ("14.1 Measuring water hardness") and make sure the machine setting matches the local water supply hardness ("14.2 Setting water hardness").

"6.7 Coee temperature "

(see section

Page 24

PROBLEM POSSIBLE CAUSE REMEDY

The coee is weak or not creamy enough.

The coee emerges too slowly or drop-by-drop.

Coee does not come out of one or both spouts.

The coee delivered is watery. The funnel (A4) is clogged. Clean the funnel with the aid of the brush (D5)

The appliance will not make coee The appliance has detected impurities

The infuser cannot be removed The appliance has not been turned o

With the descaling procedure completed, the appliance prompts for a third rinse

Milk does not ow from the milk spout (E5)

Coee ground too coarsely. Turn the grinding adjustment dial (A5) one

click anticlockwise towards "1" while the coffee mill is in operation (g. 12). Continue one click at a time until coee delivery is satisfactory. The eect is only visible after delivering 2 coees (see section "7.5 Adjusting the coee mill").

Coee not suitable. Use coee for espresso machines.

Coee not fresh. The coee pack has been opened for too long

and has lost its taste.

Coee ground too nely. Turn the grinding adjustment dial (A5) one

click clockwise towards "7" while the coee mill is in operation (g. 12). Continue one click at a time until coee delivery is satisfactory. The eect is only visible after delivering 2 coees (see section "7.5 Adjusting the coee mill").

The coee spouts (A9) are blocked. Clean the spouts with a toothpick (g. 24B).

as described in section "12.8 Cleaning the preground coee funnel".

Wait until the appliance is ready for use again in its internal circuits. "Cleaning underway" is displayed.

correctly

During the two rinse cycles, the water tank (A17) has not been lled to the MAX level

The lid (E2) of the milk carafe (E3) is dirty

The lid (E2) is not correctly in place. Assemble all the components correctly as indi-

and reselect the required drink. Contact an au-

thorized Service Centre if the problem persists.

Turn the appliance o by pressing the but-

ton (A7)

(see section

o"

Follow the instructions displayed by the appli-

ance, but rst empty the drip tray (A15) to avoid

the water overowing.

Clean the milk carafe lid as described in section

"12.10 Cleaning the milk carafe".

cated in section "9.1 Filling and attaching the

milk carafe".

"5. Turning the appliance

Page 25

PROBLEM POSSIBLE CAUSE REMEDY

The milk presents large bubbles or splashes from the milk spout (E5) or is under-frothed.

The machine emits noises or small pus of steam while not in use

The cup shelf (A12) is hot. Several drinks have been prepared in

After cleaning, the drip tray (A15) cannot be put back in the machine

The appliance emits pus of steam from the drip tray (A15) and/or there is water on the surface the appliance rests on.

The milk is not cold enough, or the type of milk not suitable for the drink requested

The froth adjustment dial (E1) is incorrectly adjusted.

The lid (E2) or the froth adjustment dial (E1) of the milk carafe are dirty

There is water in the channel on the underside of (E1),

Vegetable drinks are being used. For best results, use drinks at refrigerator tem-

The hot water connection nozzle (A8) is dirty

The machine is ready for use, or has recently been turned o, and condensate is dripping into the hot vaporiser

rapid succession

The condensate tray(A10) is not in the correct position

The drip tray grille (A14)has not been replaced after cleaning.

the froth adjustment dial

To ensure optimum results, check that the right

type of milk is used when preparing hot drinks

or cold drinks (see section “9.1 Che latte utiliz-

zare?”). Use drinks at refrigerator temperature

(about 5° C).

Adjust following the instructions in section "9.

making hot milk-based drinks".

Clean the lid and adjustment dial of the milk

carafe as described in section "12.10 Cleaning

the milk carafe".

Detach the dial and dry thoroughly.

perature (about 5° C). Adjust the amount of

froth as described in section "9.3 Adjusting the

amount of froth"

Clean the connection nozzle as described in

section "12.11 Cleaning the hot water nozzle".

This is part of normal operation. To limit the

phenomenon, empty the drip tray.

Make sure the condensate tray is inserted

correctly

Reposition the grille in the drip tray.

Page 26

Page 27

Page 28

De’Longhi Appliances via Seitz, 47 31100 Treviso, Italy www.delonghi.com

57132C8236_00_0723