Danby DPA100B2WDB User Manual

OWNER’S USE AND CARE GUIDE GUIDE D’UTILISATION ET D’ENTRETIEN

PORTABLE AIR CONDITIONER CLIMATISEUR PORTATIF

-ODELs-ODÕLEs-ODELO

MODEL  MODÈLE DPA100B2WDB

Danby Products Limited, Ontario, Canada N1H 6Z9

Danby Products Inc., Findlay, Ohio, USA 45840

13.03.14

TO OBTAIN WARRANTY SERVICE YOU MUST PROVIDE A VALID PROOF OF PURCHASE. PLEASE STAPLE YOUR RECEIPT TO THIS PAGE FOR FUTURE REFERENCE.

------------------------------------------------------------------------------------------------------------------POUR OBTENIR LE SERVICE SUR GARANTIE VOUS DEVEZ FOURNIR UNE PREUVE D’ACHAT VALIDE. VEUILLEZ AGRAFER VOTRE REÇU À CETTE PAGE POUR RÉFÉRENCE FUTURE.

-------------------------------------------------------------------------------------------------------------------

IMPORTANT - GROUNDING METHOD

This product is factory equipped with a power supply cord that has a three-pronged grounded plug. It must be plugged into a mating grounding type receptacle in accordance with the National Electrical Code and applicable local codes and ordinances. If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of the customer to exchange the existing receptacle in accordance with the National Electrical Code and applicable local codes and ordinances. The third ground prong should not, under any circumstances, be cut or removed. Never use the cord, the plug or the appliance when they show any sign of damage. Do not use your appliance with an extension cord unless it has been checked and tested by a quali¿ ed electrician or electrical supplier.

IMPORTANT - MÉTHODE POUR LA MISE À LA TERRE

Ce produit arrive d’origine avec un cordon d’alimentation équipé d’une prise à trois ¿ ches. Il doit être branché dans une prise avec une ¿ che de mise à la terre en conformité avec le Code national de l’électricité et les codes et règles locaux applicables. Si la prise murale n’a pas de mise à la terre, il est de la responsabilité et l’obligation du client de changer la prise existante pour la rendre conforme au Code national de l’électricité et aux codes et règles locaux applicables. La ¿ che de mise à la terre ne doit pas, en aucune circonstance, être coupée ou retirée. Si vous apercevez des signes de dommage, n’utilisez jamais le cordon d’alimentation, la prise ou l’appareil. N’utilisez jamais l’appareil avec une rallonge sauf si elle a été véri¿ ée et testée par un électricien quali¿ é ou un fournisseur de matériel électrique.

Contents

Table des matières

PORTABLE AIR CONDITIONER Owner’s Use and Care Guide

 Welcome .............................................................

 Safety Instructions ..............................................

 Identifying Parts ..................................................

 Features ..............................................................

 Operating Instructions .........................................

 Installation Instructions .......................................

 Care and maintenance ........................................

 Troubleshooting ...................................................

 Warranty ..............................................................

CLIMATISEUR PORTATIF Guide d’utiliser et soin de propriètaire

 Bienvenue ...........................................................

 Consignes de sécurité importantes .....................

 L'Identification des pièces ....................................

 Caractéristiques ..................................................

 Consignes d’utilisation ........................................

 Instructions d’installation .....................................

 Soins et entretien ................................................

 Dépannage .........................................................

 Garantie ..............................................................

2 3-4 4-6 6-7 8-9 10-14 15 16 17

18 19-20 21-22 23 24-25 26-30 31 32 33

CAUTION:

Read and follow all safety rules and operating instructions before first use of this product.

PRECAUTION:

Veuillez lire attentivement les consignes de sécurité et les instructions d’utilisation avant l’utilisation initiale de ce produit.

Model  Modèle

DPA100B2WDB

Welcome

Welcome to the Danby family. We are proud of our quality products, and we believe in dependable service, like you will ¿ nd in this Owner’s Use and Care Guide, and like you will receive from our friendly customer service department. Best of all, you will experience these values each and every time you use your Danby appliance. That is important, because your new appliance will be a part of your family for a long time.

Note the information below; you will need this information to obtain service under warranty. To receive service, you must provide the original receipt.

Model No:

Serial No:

Date Purchased:

NEED HELP?

Before you call for service, here are a few things you can do to

help us serve you better:

Read this Owner’s Use and Care Guide:

It contains instructions to help you use and maintain your appliance properly.

If you received a damaged appliance:

Immediately contact the retailer (or builder) that sold you the appliance.

Save time and money:

Check the Troubleshooting section at the end of the guide before calling. This section helps you solve common problems that may occur.

If you do need service, you can relax, knowing help is only a phone call away.

WARNING

Tel: 1-800-26-

(1-800-263-2629)

Improper connection of the grounding plug can result in risk of ¿ re, electric shock and/or injury to persons associated with the appliance. Check with a quali¿ ed service representative if in doubt that the appliance is properly grounded.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

To prevent injury to the user or other people and property damage, the following instructions must be followed. Incorrect operation resulting from to ignoring these instructions may cause harm or damage.

SAFETY PRECAUTIONS

ALWAYS DO THIS

Your air conditioner should be used in such a way that it is protected from moisture. e.g. condensation, splashed water, etc. Do not place or

store your air conditioner where it can fall or be pulled into water or any other liquid. Unplug unit immediately if this occurs.

Always transport your air conditioner in a vertical position and place on a stable, level surface during use.If the unit is transported laying

on it’s side it should be stood up and left unplugged for 4 hrs. Turn off the unit when not in use. Always contact a qualified person to perform repairs. If the power cord

is damaged it must be repaired by a qualified technician. Keep clearance of at least 30cm (1 foot) all around the unit from walls,

furniture and curtains, to allow for adequate air flow. If the air conditioner is knocked over during use, turn off the unit and

unplug it immediately. Always use the switch on the control panel to turn the unit on or off.

Portable air conditioners exhaust large amounts of room air. Always ensure an adequate supply of make-up air to operate efficiently.

NEVER DO THIS

Do not operate your air conditioner in a wet room such as a bathroom

or laundry room.

Do not touch the unit with wet or damp hands.

Do not press the buttons on the control panel with anything other than

your fingers.

Do not remove any fixed components. Never use this appliance if it is

not working properly, or if it has been dropped or damaged.

Never use the plug to start and stop the unit.

Do not cover or obstruct the inlet or outlet grilles.

Do not use hazardous chemicals to clean or come into contact with

the unit. Do not use the unit in the presence of inflammable

substances or vapour such as alcohol, insecticides, petrol,etc.

Do not allow children to operate the unit unsupervised.

Do not use this product for functions other than those described in this

instruction manual.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

ENERGY SAVING TIPS

OPERATING CONDITION

TOOLS FOR WINDOW KIT INSTALLATION

 Use the unit in the recommended room size.  Locate the unit where furniture cannot obstruct the air flow.

 Keep blinds/curtains closed during the sunniest part of the day.  Keep the filters clean.  Keep doors and windows closed to keep cool air in and warm air out

(cooling mode).

The air conditioner must be operated within the temperature range indicated below:

MODE

COOL

DRY

*HEAT (heat pump type)

*HEAT (electrical or heat pump)

(*) Optional feature, some models may not have this feature. Note: Performance may be reduced outside of these operating

temperatures.

1. Screwdriver (medium size, Phillips)

2. Tape measure or ruler

3. Knife or scissors

4. Saw (In the event that the window kit needs to be cut down in size

because the window is too narrow for direct installation). See www.danby.com for general instruction guide.

ROOM TEMPERATURE

17°C (62°F) ~ 35°C (95°F) 13°C (55°F) ~ 35°C (95°F)

5°C (41°F) ~ 30°C (86°F)

<30°C / 86°F

Identifying Parts

ELECTRICAL INFORMATION

WARNING

Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

 Avoid fire hazard or electric shock. Do not use an extension cord

or an adaptor plug. Do not remove any prong from the power cord.

WARNING

 Be sure the electrical supply is adequate for the model you have

chosen. This information can be found on the serial plate, which is located on the side of the cabinet and behind the grille.

 Be sure the air conditioner is properly grounded. To minimize

shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards.

 Your air conditioner must be used in a properly grounded wall

receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper receptacle.

 Ensure the receptacle remains accessible after the unit is

installed.

Identifying Parts

ACCESSORIES

I O N

F O L

S E

T L OCK

D I

D L A Y

OBR

FFOREMIT

DOM E

GNIW

PME

ONOCE

O/N

FDEEPS

NA EMIT

NOR

PARTS

PART NAME

Exhaust hose and Adaptor B (round mouth)

Window Slider Kit and screw

Foam seal Remote Controller and

Battery (For remote control models only)

Drain hose

QUANTITY

1 set

6 pc

1set

1pc

Ensure that all the accessories are included in the package and refer to the installation

instructions for their usage.

NOTE: All the illustrations in this manual are for explanatory purposes only. Your air conditioner

may be slightly different.

UNIT STRUCTURE

Fig.1

FRONT

2 3

Control Panel Horizontal Louver Blade

(adjusts manually) Carrying Handle

(both sides) Remote Signal Receptor

4 5

Front Panel

Identifying Parts

Fig.2

REAR

Upper Air Filter (behind the grille)

Air Outlet

Castor

Air Intake

Features

ELECTRONIC CONTROL INSTRUCTIONS

Fig.3

Before you begin, thoroughly familiarize yourself with the control panel and remote controller and all its functions. Select the functions you desire based on the associated symbol.

The unit can be controlled by the control panel alone or with the remote controller.

NOTE: This manual does not include Remote Controller Operation. Refer to the <<Remote Controller Instructions>> packed with the unit for this information.

Drain Outlet

Air Intake

Lower Air Filter (behind the grill)

Bottom tray drain outlet

Features

ELECTRONIC CONTROL INSTRUCTIONS

MODE select button

Selects the appropriate operating mode. Each time you press the button, a mode is selected in a sequence that goes from AUTO, COOL,

DRY, FAN and HEAT (not available on cooling only models). The mode indicator light corresponding to the chosen setting lights up.

TIMER button

Used to initiate the AUTO ON start time and AUTO OFF stop time program, in conjuction with the up arrow & down arrow buttons.

POWER button

Turns power on/off.

SLEEP button

Used to initiate the SLEEP operation.

FAN button

Controls the fan speed. Press to toggle between two fan speeds: LOW (press 1 time) and HIGH (press 2 times). The fan speed indicator light indicates the corresponding fan setting. Press the button a third time to initiate AUTO-FAN mode. In this mode, both indicator lights will light up.

Used to adjust (increase /decrease) temperature settings (1°C/2°F increments) in a range of 17°C(62°F) to 30°C(86°F) or the TIMER setting in a range of 0~24hrs. The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius. To convert from one to the other, press and hold the Up and Down buttons at the same time for 3 seconds.

LED Display

Shows the set temperature in °C or °F and the Auto-timer settings. While on DRY and FAN modes, it shows the room temperature.

UP and DOWN buttons

Also displays the following error codes: E1 - Room temperature sensor error-Unplug the unit and plug

it back in. If error repeats, call for service.

E2 - Evaporator temperature sensor error- Unplug the unit and

plug it back in. If error repeats, call for service.

- Display panel communication error - Unplug the unit and

plug it back in. If error repeats call for service.

- Bottom tray is full - Connect the drain hose and drain the

collected water away. If error repeats, call for service.

Operating Instructions

OPERATING MODES

COOL mode

- Press the "MODE" button until the "COOL" indicator light comes on.

- Press the up / down arrows to select your desired room temperature. The temperature can be set within a range of 17°C-30°C / 62°F-86°F.

- Press the "FAN SPEED" button to choose the fan speed.

HEAT mode (select models only)

- Press the "MODE" button until the "HEAT" indicator light comes on.

- Press the ADJUST buttons "up" or "down" to select your desired

room temperature. The temperature can be set within a range of 17°C-30°C / 62°F-86°F.

- Press the "FAN SPEED" button to choose the fan speed. For some

models, the fan speed can not be adjusted under HEAT mode.

DRY mode

- Press the "MODE" button until the "DRY" indicator light comes on.

- Under this mode, you cannot select a fan speed or adjust the temperature. The fan motor operates at LOW speed.

- Keep windows and doors closed for the best dehumidifying effect.

- Do not use the window hose under this mode.

AUTO mode

- When you set the air conditioner in AUTO mode, it will automatically select cooling, heating (applicable models only) or fan only operation depending on what temperature you have selected and the room temperature.

- The air conditioner will adjust the room temperature automatically to

the temperature point set by you.

- Under AUTO mode, you can not select the fan speed.

FAN mode

- Press the "MODE" button until the "FAN " indicator light comes on.

- Press the "FAN SPEED" button to choose the fan speed (1 time for LOW,

2 times for HIGH, 3 times for AUTO-FAN).

- The corresponding fan speed indicator light for each speed lights up. Both

indicators are lit up when AUTO-FAN is selected.

- The temperature cannot be adjusted.

- Do not use the window hose in this mode.

TIMER mode

- To initiate the TIMER OFF function, press the timer button when the unit is on. It indicates the Auto Stop program is initiated.

- To initiate the TIMER ON function, press the timer button when the unit

is off. It indicates the Auto Start program is initiated.

- Press and hold the UP or DOWN button to change the Auto-time by half

hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time remaining until the unit starts or stops.

- The selected time will program in 5 seconds and the system will

automatically revert back to display the previous temperature setting.

- Turning the unit ON or OFF at any time or adjusting the timer setting

to 0.0 will cancel the Auto Start/Stop timed program.

- When a malfunction (E1, E2, E4, P1) occurs, the Auto Start/ Stop

program will be cancelled.

Operating Instructions

OPERATING MODES

POWER OUTAGE

AIR FLOW DIRECTION ADJUSTMENT

SLEEP cycle

This unit features an operation mode that is designed to keep you comfortable while sleeping, and save you money on your energy bill. Simply press the sleep button. Depending on whether the unit is in heating or cooling mode, the temperature will either increase (cooling mode) or decrease (heating mode) by 1°C / 2°F every half hour for 1 hour. It will then hold this new temperature for 7 hours before returning to the original temperature setting and resuming normal operation. NOTE: This feature is unavailable in FAN and DRY mode.

In the case of a power outage or interruption, the unit will automatically re-start with the default settings after the power is restored.

Wait 3 minutes before resuming operation

After the unit has stopped, it can not operate for the first 3 minutes. This is to protect the unit. Operation will automatically start after 3 minutes.

Adjust the air flow direction manually (Fig. 4):

The louver can be set to the desired position manually.

- Do not place any heavy objects or other loads on the louver, doing so will cause damage to the unit.

- Ensure the louver is fully opened under heating operation.

Adjust manually

Fig.4

+ 25 hidden pages