Citizen CY 104, CX 120, CY 64, CY 54, CX 65 Operating Manual

Operating Manual

CS-09-05-11/2

Analytical Balances | Carat Balances | Precision Balances | High Precision Industrial Balances

CITIZEN SCALE (I) PVT. LTD.

Parwanoo. Tel. : 022 - 4243 7777 | Fax : 022 - 4243 7900 |Web: www.citizenscales.com |Email: service@citizenscales.com

Subject to technical changes and to the availability of the accessories supplied with the instruments.

0.0000

g

0.00

g

0.0

g

1

2

Contents

1 Introduction ........................................................................................................ 3

1.1 Warning & Safety Precautions ........................................................................... 4

1.2 Getting Started 5...................................................................................................

1.3 Layout 6..................................................................................................................

2 Setting up the Balance 9......................................................................................

2.1 Location 12..............................................................................................................

2.2 Warm up 14..............................................................................................................

2.3 Keys of Balance 15..................................................................................................

3 Power On 17.............................................................................................................

4 Simple Weighing 19.................................................................................................

4.1 External Calibration 23............................................................................................

4.2 Internal Calibration 25............................................................................................

4.3 Calibration Test 27.................................................................................................

4.4 Calibration Test with Actual Calibration .......................................................... 29

5 Overview of Menu 32..............................................................................................

5.1 Operating Instruction ......................................................................................... 33

5.2 Description of Menu .......................................................................................... 34

6 Functions 44..............................................................................................................

6.1 Piece Counting 44...................................................................................................

6.2 Percent Weighing (%) ........................................................................................ 49

6.3 Custom Units 57........................................................................................................

6.4 Animal Weighing 61.................................................................................................

6.5 Formulation 65..........................................................................................................

6.6 Check weighing 69.................................................................................................

6.7 Totalization 73...........................................................................................................

6.8 Density Determination 77.......................................................................................

6.9 Pipette Calibration ............................................................................................. 83

6.10 Statistics ............................................................................................................... 89

7 Parameter Settings 93............................................................................................

7.1 Time & Date Settings 96..........................................................................................

7.2 ID / LID Settings 98.................................................................................................

7.3 Auto Calibration 99.................................................................................................

7.4 Windows Direct Communication 102.....................................................................

8 ISO / GLP - Compliant Printout ......................................................................... 105

9 Data Interface 107.....................................................................................................

9.1 Data Output Format 108.........................................................................................

9.2 Data Input Format 110.............................................................................................

9.3 Cabling Diagram 111...............................................................................................

10 Error Codes 112..........................................................................................................

11 Care & Maintenance 114.........................................................................................

12 Dimensional Drawings 119.......................................................................................

13 Specification 123......................................................................................................

14 Accessories ........................................................................................................ 134

The models of the CX, CY, CT, CG and SSH Series are weighing instruments of special and high accuracy designed for the measurement of mass, covering a range from 0.01mg to 100 kg.

CX, CY, CT, CG and SSH models meet the highest requirements on the accuracy and reliability of weighing results through the following features:

– Filtering for unfavorable ambient

conditions, such as vibration, drafts, etc.

– Stable and repeatable weighing

results

– Excellent readability under any

lighting conditions

– Rugged, durable weighing system

These weighing instruments speed up your simple routine applications through following features:

– Extremely fast response times

– Built-in applications

• Counting

• Percent weighing

• Animal weighing

• Formulation

• Totalization

• Custom Unit

• Check Weighing

• Density Determination

• Pipette Calibration

• Statistics

1. Introduction

3

The balance has been constructed in accordance with the European Directives as well as international regulations and standards for operation of electrical equipment, electromagnetic compatibility, and stipulated safety requirements. Improper use or handling,however, can result in damage and/or injury.

To prevent damage to the equipment, please read these operating instructions carefully before using your balance.

Keep these instructions in a safe place. Follow the instructions below to ensure safe and trouble-free operation of your balance.

Do not use this balance/scale in a hazardous area/location.

If you use electrical equipment in installations and under ambient conditions requiring higher safety standards, you must comply with the provisions as specified in the applicable regulations for installation in your country.

Make sure that the voltage rating printed on the AC adapter is identical to your local line voltage.

Warning when using pre-wired RS-232 connecting cables: The pin assignments in RS-232 cables purchased from other manufacturers may be incompatible with Citzien balances. Be sure to check the pin assignment against the chart on page 111 before connecting the cable.

– The only way to switch the power off

completely is to disconnect the AC adapter.

– Connect only Citizen accessories

and options, as these are optimally designed for use with your Citizen balances.

– Note on Installation:

The operator shall be responsible for any modifications to Citizen equipment andfor any connections of cables or equipment not supplied

by Citizen and must check and, if necessary, correct these modifications and connections. On request, Citizen will provide information on the minimum operating specifications

– Protect the DC adapter and the

weighing instrument from contact with liquids.

– When cleaning your balance,

make sure that no liquid enters the balance housing; use only a slightly moistened cloth to clean the balance.

– Do not open the balance/scale

housing. If the seal is broken, this will result in forfeiture of all claims under the manufacturer’s warranty.

– If you have any problems with your

balance contact your local Citizen office, dealer or service center

1.1 Warnings and Safety precautions

4

– Total ease of operation

– Direct Communication with MS Excel,

MS Word and other windows application.

– ISO/GLP-compliant recording

capability for printouts

– Serial RS-232 port for optional

connection to a PC or Printer.

– Optional USB interface available on

request.

CX / CY (0.1 mg) & CT

1. Keypad

2. Display

3. Model plate

4. Weighing pan (90 Fmm)

5. Draft shield (CX, CY & CT)

6. Leveling feet

7. Pan Cover

8. DC adapter socket

9. Provision for anti-theft device

10. Sprit Level

11. RS232C interface

12. Additional Display Sockets.

13. Foot Tare Switch Socket.

14. Calibration Switch (for Verified Balance)

15. Gem Bowl (CT)

Keys, operation and display are identical for all CITIZEN balances.

CY (1 mg with Draft shield)

1. Keypad

2. Display

3. Model plate

4. Weighing pan (128mm x 128mm)

5. Draft shield (CX, CY & CT)

6. Leveling feet

8. DC adapter socket

9. Provision for ant-itheft device

10. Spirit Level

11. RS232C interface

12. Additional Display Sockets.

13. Foot Tare Switch Socket.

14. Calibration Switch ( for Verified Balance)

Keys, operation and display are identical for all CITIZEN balances.

1.3 Layout

6

4

1

2

3

7

5

4

CX / CY (0.1 mg) & CT

CY (1 mg)

910

11

146 12 138

Storage and Shipping Conditions

Do not expose the balance/scale to extreme temperatures, blows, shocks, vibration or moisture.

Unpacking the Equipment

After unpacking the balance/scale, check it immediately for any visible damage as a result of rough handling during shipment

If you see any sign of damage:

It is a good idea to save the box and all parts of the packaging until you have successfully installed your balance. Only the original packaging provides the best protection for shipment. Before packing your balance, unplug all connected cables to prevent damage.

Contact your local Citizen office, dealer or service center

Accessories Supplied

The equipment supplied includes the following :

– Balance with display and control unit – Operating Manual – DC adapter – Gem bowl (CT scales only) – Pan Support (CX / CY / CT) – Weighing pan – Draft shield (CX / CY / CT) – Wind Shield (CX / CY / CT) – Base Plat S.S. (CX / CY / CT) – Pan Cover (CX / CT) – 1 Pair of Corner hole Cover

(CX / CY / CT)

Cautionary notes

Citizen balances may not be operated in hazardous areas.

Before attachment of the DC adapter, check whether the imprinted voltage value matches the local supply voltage. If it does not, contact your local CITIZEN dealers.

CITIZEN balance may only be used indoor in dry environment.

1.2 Getting Started

5

15

8

7

CG

1. Keypad

2. Display

3. Model plate

4. Weighing pan (198 mmX 205 mm)

6. Leveling feet

8. DC adapter socket

9. Provision for anti-theft device

10. Spirit Level

11. RS232C interface

12. Additional Display Sockets.

13. Foot Tare Switch Socket.

14. Calibration Switch (for Verified Balance)

Keys, operation and display are identical for all CITIZEN balances.

910

11

146 12 138

CY (1mg)

1

2

3

4

CG

SSH

1. Keypad

2. Display

3. Model plate

4. Weighing pan (400mm x 300mm)

6. Leveling feet

8. DC adapter socket

9. Provision for anti-theft device

10. Spirit Level

11. RS232C interface

12. Additional Display Sockets.

13. Foot Tare Switch Socket.

14. Calibration Switch (for Verified Balance)

Keys, operation and display are identical for all CITIZEN balances.

11

6 12 8

1

2

3

4

10

CY (1 mg with wind shield)

1. Keypad

2. Display

3. Model plate

4. Weighing pan (128mm x 128mm)

5. Wind shield (CX, CY & CT)

6. Leveling feet

8. DC adapter socket

9. Provision for ant-itheft device

10. Spirit Level

11. RS232C interface

12. Additional Display Sockets.

13. Foot Tare Switch Socket.

14. Calibration Switch ( for Verified Balance)

Keys, operation and display are identical for all CITIZEN balances.

5

2. Setting Up the balance

9

Balance with Analytical Draft-Shield (or Wind Shield) Chamber

• Position the Draft shield carefully on the balance.

Step 1: Open your New balance and draft shield you will see lock mounted on balance body and lock plate mounted below draft shield .

Step 2: Put your draft shield in same place and direction guided through RED color lines marked on this sticker, with gentle hand push & rotate draft shield clock wise as shown in figure.

: While keeping draft shield on balance ensure you do not damage weight loading point.

Note : Ensure there must not be any gap between balance and draft shield, if incase there is gap repeat again above procedure.

Step 3: Push fix both corner hole cover on bottom body of draft shield as shown in figure.

• The Procedure for setting up the balance with wind shield is same as that of one with draft shield

Weight

Loading

Point

Corner

Hole Cover

Lock Plate

Lock

• Place the components listed below inside the chamber in the order given:

(For CX / CY (0.1mg) / CT Series Balances)

– Corner Cover – Base plate – Pan Cover – Weighing pan

• Place the components listed below inside the chamber in the order given:

(For CY (1mg) Series Balances)

– Corner Cover – Base plate – Pan Support – Weighing pan

10

Draft shield

Wind shield

The optimum location

The correct location makes an important contribution to the accuracy of the weighing results of high-resolution analytical and precision balances.

Hence, ensure a stable, vibration-free position as horizontal as possible.

Avoid

• Direct sunlight

• Excessive temperature fluctuations,

• Drafts (Power ----- Air Conditioning System, Fans can also cause drafts)

The best position is an a stable bench in a corner protected against drafts as far possible from doors, windows, radiators or the ventilation slots of air conditioners.

Anti-theft device

Citizen Balance are equipped with a lug for optional anti-theft device.

The anti-theft device (cable with lock) is suitable for all models. It is available from CITIZEN under order number CAD01.

2.1 Location

12

11

• Place the components listed below inside the chamber in the order given: (For CG Series Balance)

– Bush – Weighing pan

• Balances with a Rectangular Weighing Pan and a Weighing Capacity over 10 kg – Place the weighing pan on the balance/scale

Under Weighing

A port for a under weighing hanger is located on the bottom of the balance.

• Remove the under weighing cover from the bottom of the balance (as shown alongside)

• Suspend the below-balance weighing hook supplied from the hanger

• If necessary, install a shield for protection against drafts

14

13

Leveling the Balance

Citizen balances have a level control and adjustable leveling feet to compensate for slight irregularities in the weighing bench surface. The balance is exactly horizontal when the air bubble is in middle.

Turn the two leveling feet as desire picture in diagram so that air bubble comes in middle. Air bubble at “12 o’clock” Turn both leveling feet counter- clockwise. Air bubble at “3 o’clock” Turn left leveling foot clockwise,

right leveling foot counterclockwise Air bubble at “6 o’clock” Turn both leveling feet clockwise Air bubble at “9 o’clock” Turn left leveling foot clockwise,

right leveling foot counterclockwise

Note : The balance must be re-leveled each time it is moved to a new location.

Leveling Balances with a Weighing Capacity up to 10 kg

Leveling Balances with a Weighing Capacity over 10 kg

• Adjust the leveling feet until the air bubble is centered within the circle of the level indicator

Connecting Electronic Peripheral Devices

Make absolutely sure to unplug the balance from DC power before you connect or disconnect a peripheral device (printer or PC)to or from the interface port.

Warmup Time

To deliver exact results, balance must warm up to operating temperature for as leasted below before the first weighing operation is carried out.

• CX / CY (0.1mg) / CT all Analytical models: at least 60 minutes

• CY (1mg) / CG / SSH all Precision models: at least 30 minutes

Using Verified Balances as Legal Measuring Instruments in the EU* balance must warm up for at least 24 hours after initial connection to DC power.

2.2 Warm Up

16

15

2

11

10

12

13

8

9

3

4

17

14

15

16

5

2

7

18

1 6

1 On/Off key: Switches the display on / off 2 Tare key: Press here to tare the weight of any container so

that the readout shows the net weight of samples, also used to store reference settings. This key used to delete the statistics when F StAt mode.

3 Cancel Function : Delete (Clear Function) This key is

generally used to interrupt/cancel functions; for example: – to end an application program – to interrupt calibration/ adjustment routines

4 Toggle Key : Press here to change the Unit, Also used to

increment digit.

5 Cal Menu Function : Press here to start calibration/

adjustment or to enter user menu, Also use to shift flashing digit from left to right. this key is used in the F PiP mode to accept the volume during the calibration procedure.

6 Print Key : Press this key to send displayed values over the

built-in data interface to a DataPrint printer or a PC. 7 Weight Units 8 Weight readout in the selected weight unit

9 Capacity Bar : This indicates the total amount of

weight on the Pan

10 Stability Symbol : This symbol is displayed when the

weight place on the pan achieve stability

11 Asterik Symbol : This Symbol is displayed when the

display is locked

12 Stability Filer : This symbol indicates the chosen stability

filter

13 Symbol indicating that the Auto / Manual

calibration/adjustment function is active 14 Symbol indicating the active program 15 Battery Level Indicator : This symbol is indicates the

Current charge of the battery 16 Symbol indicating that a printout is being generated 17 Symbol indicating that a GLP compliant printout is

being generated 18 Seven segment readout indicating the active

program

2.3 Keys of Balance

18

17

Switch on & off

Change Weighing Unit

Switch References

Print Weighing Results

Calibrate (adjust)

Call Menu

Weighing mode (operation)

Press briefly Press & Hold

Confirm Setting

Tare

Confirm Reference Setting

Abort / Cancel and Footer when GLP is ON

On / Off key

Toggling key

Tare keyCancel / Footer

Print key

CAL /

Menu key

Key Functionality in simple weighing mode

Citizen balances have several control levels the following section explains key functionality in simple weighing mode.

Short-form operating Instructions

Press key briefly

Press and hold key until desired display appears

Automatic procedure

Connect DC Adaptor and Power ON the balance.

– It will display version number for software

– It will display numeric countdown

– It will display 88888888

– The system initialization process will begin with the display indicating the current

progress. (INIT 1% to INIT 100%)

– After the initialization is complete (100%) It will enter stand by mode &

display clock.

Stand by Mode

– After Power ON and initial test balance will automatically come in stand by mode.

– Press ON / OFF key to come to basic weighing

– Press ON / OFF key in basic weighing to come back to Stand by Mode

3. Power ON

Purpose

The basic weighing function is always accessible and can be used alone or in combination with an application program (counting, weighing in percent, etc.).

Features

– Taring the balance you can tare the balance within the entire weighing range. – Assigning IDs to weights (as needed) – Printing weights

4. Simple Weighing

19

20

Simple Weighing

4.0.2 Tarring

ð Place empty container on the balance.

ð The weight is displayed.

ð Press <Tare> key briefly, the balance displays zero

ð Add weighing sample to container, the net weight is displayed.

If the container is removed from the balance, the tare weight will be shown as a negative value.

4.0.1 Simple weighing

ð Place weighing sample on the weighing pan.

ð Wait until the stability symbol appears

ð Read the result.

ð Bar Graph will glow according to weight kept ON the PAN.

Tarring

22

In case if stability is not achieved & user presses <TARE> key, display will shows “---------------” until stability is achieved.

Display then shows “0.0000 gm”

4.0.3 Switching of weight units

All Citizen balances can display weight values in different weight units.

The factory setting is Unit 1 (gm), Unit 2 (ct), Unit 3 (gm)

Switching between unit 1, unit 2 and unit 3

ðPress <TOGGLE> key the display switches to the 2nd weight unit.

ðPress <TOGGLE> key again, the display switches to the 3rd weight unit. OR

Application unit (If same is selected in menu)

Note : With certified balances the unit selection can be blocked following installation

if required by national legislation.

21

Switching of Weight Units

-----------------------20-Jul-10 10:35AM Citizen Model CX 220 Ser.no. 9223102 Ver.no. r0.1.5.3 ID 1234567

-----------------------LID: 1111111 + 49.9999 g + 249.9990 ct + 1.763690 oz + 49.9998 g + 249.9990 ct + 1.763690 oz + 49.9999 g

-----------------------20-Jul-10 10:36AM Name:

................

------------------------

When GLP ON

Print out generated when Unit Toggling is done between Unit1 (g), Unit2 (ct), Unit3 (Oz) in Simple Weighing.

+ 49.9999 g + 249.9990 ct + 1.763690 oz + 49.9998 g + 249.9990 ct + 1.763690 oz + 49.9999 g

When GLP OFF

Print out generated when Unit Toggling is done between Unit1 (g), Unit2 (ct), Unit3 (Oz) in Simple Weighing.

4.0.4 Simple weighing Print out

Note : 1) User cannot enter into the external calibration or menu when GLP is ON & footer has not been printed.

2) To print footer user will have to Press <CANCEL> key.

If Balance is connected externally to PC or Data Printer via Rs232 Cable, successful or unsuccessful calibration report will be automatically generated after the completion of Calibration process.

Calibration Report

24

Unsuccessful Calibration

When GLP OFF

When GLP ON

-----------------------------14-Jul-10 03:46PM Citizen Model CX 220 Ser.no. 9930508 Ver.no. R0.1.04 ID 1234567

-----------------------------Calibration: External

W-ID ..................

Temperature 32.898'C Set + 20.00g

External Cal Failed

-----------------------------14-Jul-09 03:46PM

Name: ................

------------------------------

Calibration : External

W-ID ............

Temperature 32.905'C Set + 20.00g

External Cal Failed

Successful Calibration

When GLP OFF

Calibration : External

W-ID ............

Temperature 32.905'C Set + 20.00g Diff. -0.01g External Cal Done Diff. 0.00g

When GLP ON

-----------------------------14-Jul-10 03:46PM Citizen Model CX220 Ser.no. 9930508 Ver.no. R0.1.04 ID 1234567

-----------------------------Calibration: External

W-ID ..................

Temperature 32.898'C Set + 20.00g Diff. 0.00g External Cal Done

Diff. 0.00g

-----------------------------14-Jul-09 03:46PM

Name: ................

------------------------------

To obtain weighing results, the balance must be matched to the acceleration due to gravity at its location.

Calibration is necessary

ð Before the balance is used for the first time. ð At regular intervals during weighing operation. ð After a change in location.

Procedure

To obtain accurate results, the balance must be connected to the power supply and allowed to warm up to the operating temperature as described on Page No

Ensure that the weighing pan is unloaded and close the doors of the draft shield (if used). Balance should be Zero before calibration.

ð Have required calibration weight ready ð Press and hold <CAL> key, display, shows “CAL Et” ð Release <CAL> key now. ð The required calibration weight value will be displayed. ð Place calibration weight in center of pan.

The calibration (adjustment) is finished when “CAL donE” message is displayed. The balance is again in the weighing mode and ready for operation.

Note : With certified balances, the calibration can be disabled after installation if required by the national certification regulations.

The adjustment can be terminated at any time using the <CANCEL> key. The following message appears : ‘Abort’

14

23

Calibration

4.1 External Calibration (adjusting)

To obtain weighing results, the balance must be matched to the acceleration due to gravity at its location.

Calibration is necessary

ð Before the balance is used for the first time. ð At regular intervals during weighing operation. ð After a change in location.

Procedure

To obtain accurate results, the balance must be connected to the power supply and allowed to warm up to the operating temperature as described on Page No

Ensure that the weighing pan is unloaded and close the doors of the draft shield (if used). Balance should be Zero before calibration.

ð Press and hold <CAL> key, display, shows “CAL Int” ð Release <CAL> key now.

Internal Calibration process Starts.....

- When the Internal Weight is being loaded “C” will be displayed on display.

- When the Internal Weight is being unloaded “CC” will be displayed on display.

Calibration is finished when ‘Int.done’ is message is displayed.

The adjustment can be terminated at any time using the <CANCEL> key. The following message appears : ‘Abort’

14

If Balance is connected externally to PC or Printer via Rs232 Cable, successful or unsuccessful calibration report will be automatically generated after the completion of Calibration process.

26

25

Internal Calibration

Successful Calibration Unsuccessful Calibration

When GLP OFF

Calibration: Internal

Start: Manual Temperature 29.449'C Diff. + 0.0009g

Internal Cal Done Diff. 0.0000g

When GLP ON

-----------------------20-Jul-10 10:32AM Citizen Model CX 220 Ser.no. 9223102 Ver.no. r0.1.5.3 ID 1234567

-----------------------Calibration: Internal

Start: Manual Temperature 29.449'C Diff. + 0.0009g

Internal Cal Done Diff. 0.0000g

-----------------------20-Jul-10 10:32AM Name:

................

------------------------

When GLP OFF

When GLP ON

-------------------------------20-Jul-10 10:34AM Citizen Model CX 220 Ser.no. 9223102 Ver.no. r0.1.5.3 ID 1234567

-----------------------Calibration: Internal

Start: Manual Temperature 29.495'C

Internal Cal Failed

-----------------------20-Jul-10 10:34AM Name:

................

------------------------

Calibration: Internal

Start: Manual Temperature 29.495'C

Internal Cal Failed

Internal Calibration Report

4.2 Internal Calibration

If Balance is connected externally to PC or Data Printer via Rs232 Cable, successful or unsuccessful calibration report will be automatically generated after the completion of Calibration process.

Calibration test determines the difference between the actual weight and the measured weight Calibration test can be turned ON or OFF from the user menu. When ON, cal test would be performed on external or internal calibration whichever is selected in User Menu.

Procedure

ð Have required calibration weight ready ð Press and hold <CAL> key, display, shows “CAL Et” ð Release <CAL> key now. ð The required calibration weight is shown on the display. ð Place calibration weight in center of pan.

ð After the cal Test procedure is completed the difference between the actual & the

measured weight will be displayed on display.

The adjustment can be terminated at any time using the <CANCEL> key. The following message appears : ‘Abort’

Calibration Test Report

28

27

Calibration (adjusting)

When GLP ON

-------------------------------14-Jul-10 00:03AM Citizen Model CX220 Ser.no. Ver.no. ID

-------------------------------Calibration: External

W-ID ..................

Temperature Set Diff. Calibration Test Done

--------------------------------14-Jul-10 00:03AM

Name: ................

---------------------------------

1111111

r0.1.04.01

860054081

30.710'C +200.0000g + 0.0047g

When GLP OFF

Calibration: External

W-ID ..................

Temperature Set Diff. Calibration Test Done

30.710'C +200.0000g + 0.0047g

4.3 Calibration Test

To correct the weighing results, the TARE key need to be pressed when the difference is display upon pressing the TARE key. Actual calibration is performed ‘CAL done’ is displayed and the weighing results are corrected as shown alongside.

Procedure

ð Have required calibration weight ready ð Press and hold <CAL> key, display, shows “CAL Et” ð Release <CAL> key now. ð The required calibration weight is shown on the display. ð Place calibration weight in center of pan. ð The difference between the actual & the measured weight will be displayed. ð Press the Tare key when the difference is displayed. ð Actual Calibration is perform and Cal done is displayed.

The adjustment can be terminated at any time using the <CANCEL> key. The following message appears : ‘Abort’

If Balance is connected externally to PC or Printer via Rs232 Cable, successful or unsuccessful calibration report will be automatically generated after the completion of Calibration process.

Calibration Test Report

30

29

Calibration (adjusting)

Calibration : External

W-ID ............

Temperature 32.905'C Set + 200.0000g Diff. -0.1235g External Cal Done Diff. 0.0000g

-----------------------------------14-Jul-10 03:46PM Citizen Model CX220 Ser.no. 9930508 Ver.no. R0.1.04 ID 1234567

-----------------------------------Calibration: External

W-ID ..................

Temperature 32.898'C Set + 200.0000g Diff. -0.1235g External Cal Done

Diff. 0.0000g

-----------------------------------14-Jul-09 03:46PM

Name: ................

------------------------------------

When GLP OFF

When GLP ON

4.4 Calibration Test with Actual Calibration

31

Print User Menu

On / Off

Change Sub Menu Setting

Store and quit menu

Confirm Setting

Press briefly Press & Hold

Menu (called up with )

Increments the value of digit

Change Main menu options

Shifts the digit from left to right

Quit User Menu

Key Functionality in User Menu

The following section explains key functionality in User Menu mode.

On / Off keyOn / Off key

Toggling key

Tare key

Cancel key

Print keyPrint key

CAL /

Menu key

32

In this menu, you can select unit 1, 2, 3 or Application Program, adjust the stability filter, Calibration choice, Auto Zero Tracking, automatic shutdown and print setting.

Entry into menu : Press and hold <CAL> Key until “MENU” appears on the display. Release key, the 1st menu options “F none”

Select menu options Press <CAL> Key briefly. Press key repeatedly to view the current balance settings Main Menu Option.

Modify settings Press <Toggle> Key repeatedly until the desired setting appears.

Confirm settings Press <TARE> key breifly when desired setting appears.

Store settings Press and hold <TARE> Key until “StoreED” appears.

Abort Press <CANCEL> Key briefly, The balance returns to the weighing

mode without storing the changes.

3

4

1

2

lb

2

OZ

2

Ozt

GN

dwt

Weighing Unit 2 Stability Filter Calibration Menu Calibration Test

Unit 2 ct Stb 2

CAL ET CA .

Weighing Unit 1

Unit 1 gm

GLP

G P

ES

Reset

2

b

2

m

2

gm

2

mg

2

kg

2

1

2

Stop Bit

A. 1

A. 5

A. 10

Auto Off

A. OFF -

O

Baud Rate

9600

tlh(2)

GNdwt

tlt(2)

mo

b

m

mg

kg

ct

lb

OZ

Ozt

tlh(2)

tls(2)

Weighing Unit 3

Unit 3 gm

3

GNdwt

tlt(2)

mo

b

m

mg

kg

ct

lb

OZ

Ozt

tlh(2)

tls(2)

tlt(2)

mo

Auto Zero Tracking

Azt

Print Menu

P

A.

Parity

e

P

E E

P

a

P

spac

P

F

Pcs

F

edF

PPF

CsF

A

F

A

F

F f

SAF

F

Weighing Mode

F e

W. Application

%

Auto

F f

Auto

F

Auto

4800

19200

57600

5 Overview of Menu

ð Press & hold CAL Key until “Menu” appears on the display. ð Release the CAL Key ð Existing preselected function is displayed from among the above mentioned 4

functions. This existing function is displayed with the stability indicator ON

ð Press Toggle Key to Toggle to the desired functions. ð Press Tare Key briefly, once the desired function is displayed.

Stability indicator will be ON for that particular function now.

ð Then Press & hold TARE Key once again till “STORED” is 5displayed on the display.

ð If more then one changes are to be made within the Menu, make all the desired

changed by pressing toggle key to toggle within the SUB-Menus & Pressing Tare

key briefly. Stability indicator will be ON for those changed Submenu Options Then finally, pressing & holding TARE key until “Stored” is displayed, will store all the changes made within different menu options.

Note : If user did not press & hold <TARE> key & “Stored” message appears on the

display then any change made by user will remain unchanged.

Above instructions are to be followed for all menu options except : “Reset”

33

Application Menu :

5.2.1 Special applications and functions

Your balance can do more than just weighing. Built-in applications and functions expand its possibilities and facilitate your daily work. You will learn these applications and functions in the following Sections.

Preselecting a function

In this menu option you can preselect a function which will then be available in the weighing mode (Unit 3) at a keystroke The following functions are available.

Piece counting

Your balance counts the pieces you add to or remove from the weighing container.

Percent weighing

Your balance allows you to weigh in to a preset value or determines percentage weight deviations .

Custom Unit : Your Balance allows you to weigh in any customized unit.

Animal Weighing : Your Balance allows you to weigh animals in motion. You have the

option of Auto and Manual Animal Weighing.

Checkweighing : Your balance allows you to check whether a sample corresponds to a preset target or is within a specific tolerance range.

5.2 Description of Menu

34

5.1 Operating Instruction

Formulation : Your Balance allow individual weighing values to be summed to a total.

Totalization : Your balance allows you to weigh, individual weighing in piece which can

be summed to a total.

Density Determination : Your balance allows you to determine density of solids. Purity of gold can also be determined on the basis of density.

Pipette Calibration : Your balance allows you to calibrate the pipette used in laboratories for experimenting with liquids.

Statistics : Your balance allows you to obtain the statistics of the weighing data.

No function preselected You have no function available in the weighing mode (factory setting).

Note :

Above function will replace preset unit 3 automatically.

35

36

5.2.2 Unit 1, 2, 3 - selecting

The following weight units can be selected. With certified balance the unit selection can be blocked following installation if required by national legislation. Unit Conversion factor

g kg lb oz ozt GN dwt ct mg mo m H tl S tl t tl b

gram kilogram pound ounce troy ounce grain pennyweight carat Milligram momme mesghal Hong Kong taels Singapore taels Taiwan taels baht

1 1 kg 1 lb 1 oz 1 ozt 1 GN 1 dwt 1 ct 1 mg 1 mo 1 m 1 Htl 1 S tl 1 t tl 1 b

= = = = = = = = = = = = = =

1000g

453.59237g

28.349523125g

31.1034768g

0.06479891 g

1.555173843g

0.2g

0.001g

3.749999953 g

4.6083162 37,42900 g

37.799366256g

37.499995313g

15.1999998438g

37

5.2.3 Adjusting the stability Filter

You can use the stability Filter to match the balance to the ambient conditions.

2 Setting with normal balance surroundings (factory setting) 3 Setting with unstable balance surroundings. The balance operates slower

but is less sensitive to external influences (vibrations, etc.) 4 Setting with extreme unstable balance surroundings. The balance operates even slower but is less sensitive to external influences (vibrations, etc.) 1 Setting with very stable balance surroundings. The balance operates very quickly

but is sensitive to external influences (vibrations, etc.)

5.2.4 Selecting Calibration Option

User can select any of the Two option for Calibration.

CAL ET If the user select this option then the machine will perform External Calibration

when the CAL key is press & hold to display “CAL Et” & at this moment if user release the key, user can enter into the External calibration.

CAL OFF When user press & hold CAL key, directly “Menu” appears on the display

without CAL Et option. Thus user cannot enter into the calibration process.

CAL INT If the user select this option then the machine will perform External Calibration

when the CAL key is press & hold to display “CAL Int” & at this moment if user release the key, user can enter into the Internal calibration.

5.2.5 Calibration Test

User Can select any Two calibration test option.

CAL T ON If the user select this option then the machine will perform Calibration Test

when the CAL key is press & hold Calibration Test will perform on Internal or External which ever is selected in calibration menu.

CAL T OFF Actual Calibration will be performed When the CAL key is press & hold .

5.2.6 Auto Zero Tracking

In this option, user can select whether to enable or disable Auto Zero Tracking (Factory setting is ON)

The auto zero tracking continuously corrects any deviation from the zero point for example which can be caused due to slight contamination (i.e. due to dust particles) on the weighing pan.

38

5.2.7 Setting baud rate (data transmission rate)

The data transmission rate (baud rate) determines the speed of the transmission via the serial interface. The unit is baud (1 baud (bd) = 1 bit/second).

The following setting are available. bd 300, bd 600, bd 1200, bd 2400, bd 4800, bd 9600 (default), bd 19200, bd 57600

5.2.8 Setting Parity

This feature determines the parity of the transmitted data. The following settings are available: Parity, None (default), odd, even, mark, space.

5.2.9 Stop Bit Selection

This setting allows the user to select the stop bit for the transmitted data. The following settings are available: stop bit 1 (Default) and stop bit 2.

39

Print Menu

5.2.10 Selecting data transfer mode

In this menu block you tell the balance how a value should be transferred to a peripheral device (e.g. computer).

Prn. req The next possible stable value will be transferred after triggering of the

Print key.

Prn. Con All Values will be continuously transferred regardless of stability.

Prn. oFF Data Transfer mode switched off

Prn. Aut Next Possible stable value will be transfer automatically when the display

weight changes by + 1d.

Prn A.Ld Next possible stable value will be transferred automatically when the

display weight changes by +/- 10d

5.2.11 GLP Menu Setting

GLP oFF If the user select this option then the balance print format are not compliance to ISO/GLP/GMP.

GLP on If the user select this option then the balance print format are compliance to ISO/GLP/GMP.

Note

If user selected GLP ON do ensure that user print footer for entering into next transaction and enter into user Menu or Calibration.

40

F none No Function Unit 1 gm Unit 2 ct Unit 3 gm Stb 2 balance environment set to Normal CAL Et CAL External CAL t CAL TEST OFF Azt ON Auto Zero Tracking set ON bd9600 Transmission rate Pr None Parity set to none Stpbt 1 Stop bit one Print Req GLP OFF A. oFF - no automatic standby

5.2.14 Reset of the balance setting

Reset balance setting and functions to factory setting (rESEt)

ð Select “rESEt” and Press <TOGGLE> key breifly, display show “YES” ð Press <TARE> key breifly, display show “stored”

The balance is now reset to the factory setting and returns to the weighing mode._

Factory Setting

42

5.2.12 GLP Menu Setting

GLP off : If the user select this option then the balance print format are not compliance to ISO/GLP/GMP.

GLP on : If the user select this option then the balance print format are compliance to ISO/GLP/GMP.

Note

If user selected GLP ON do ensure that user print footer for entering into next transaction and enter into user Menu or Calibration.

5.2.13 A. Off - Setting automatic standby

The automatic standby appreciably extends the operating life of your Battery (If Install) (Optional)

The balance will enter stand by mode if A-OFF is activated. The display on the balance remains zero for a specific time as selected in the A.OFF menu.

A. Off - : no automatic standby (factory setting) A. Off 1 : automatic standby after 1 minutes A. Off 5 : automatic standby after 5 minutes A. Off 10 : automatic standby after 10 minutes

41

USER MENU PRINT OUT

Press the Print Key in the user Menu to Print the current status of user menu.

43

When GLP ON When GLP OFF

-----------------------------------14-Jul-10 03:46PM Citizen Model Cy 220 Ser.no. 9930508 Ver.no. R0.1.04 ID 1234567

-----------------------------------App : F Per Unit1 : g Unit2 : ct Unit3 : g Stb : 2 Cal : Ext Cal test : Off Azt : On Baudrate : 9600 Parity : None Stop bit : 1 Print : Request GLP : On Auto Off : Off

-----------------------------------14-Jul-10 03:46PM

Name: ................

------------------------------------

App : F Per Unit1 : g Unit2 : ct Unit3 : g Stb : 2 Cal : Ext Cal test : Off Azt : On Baudrate : 9600 Parity : None Stop bit : 1 Print : Request GLP : On Auto Off : Off

6.1 Piece counting

Procedure

Piece counting presupposes that you have preselected the “F count” function in the menu

ðPlace the empty container on the pan. ðPress the <TARE> key briefly to tare the balance. ðPress the <TOGGLE> key briefly until “PCS” appears on the display.

Your balance now needs the weight of a reference number.

ðPress and hold the <TOGGLE> key until you are prompted to load the reference

pieces.

ðYour balance suggests the last set reference no. as the reference number.

You can accept this suggestion or select one of the other reference numbers available (5, 10, 20,50, 100 pieces, Free, wref, Update) by briefly pressing the <TOGGLE> key.

Note : We recommend you to choose a reference number as high as possible as the balance determines the average weight per piece and stores it as the reference weight. As it is seldom, that all pieces weigh exactly the same, the larger the reference number selected, the greater the accuracy of the reference weight. This application assumes uniform weight of each piece.

ðWhen you have placed exactly the same number of pieces on the weighing pan as

selected reference pieces press TARE key. As soon as the weighing result is stable, the calculated average piece weight is accepted as the reference.

ðAfter your balance has determined the piece weight, it displays the pieces as per

selected number and is now ready for piece counting. You can use the <TOGGLE> key at any time to switch the display between the piece number display, weighing unit 1 and weighing unit 2.

Note : The current set weight remains stored until it has been redetermined.

44

6. Functions

6.1.1 FREE (Reference settings)

The FREE option allows the user to set any reference other than the fixed available reference. (Default value is 001 and maximum possible value is 999)

Procedure

ð Place the empty container on the pan. ð Press the <TARE> key briefly to tare the balance. ð Press the <TOGGLE> key briefly until “pcs” appears on the display.

Your balance now needs the weight of a reference number. ð Press and hold the <TOGGLE> key until you are prompted to load the reference pieces.

ð Your balance suggests the last set reference no. as the reference number. ð Press the <TOGGLE> key until FREE is displayed. ð Press the <TARE> key to enter FREE reference settings. ð Last stored FREE value first digit flashing. Flashing digit indicates that digit value or

place can be changed.

ð Press <TOGGLE> key ( ) to change the value of the Flashing digit. ð Press <CAL> key ( )to shift the flashing digit from Left to Right ð When you have placed exactly the same number of pieces on the weighing pan

as set in the FREE setting, press TARE key. As soon as the weighing result is stable, the calculated average piece weight is accepted as the reference

Now further weighing in PCS will be with respect to the reference calculation based upon the FREE setting.

45

6.1.2 wRef settings

If the piece weight is known, it can be entered directly. To do this, press the TARE key when the system displays wRef in the reference menu. An input field appears, in which the piece weight can be entered. Since the balance does not have to determine a reference by weighing, the result of the piece counting (the number of pieces currently on the weighing pan) is displayed right after the piece weight has been confirmed.

Procedure

ð Place the empty container on the pan. ð Press the <TARE> key briefly to tare the balance. ð Press the <TOGGLE> key briefly until “pcs” appears on the display.

Your balance now needs the weight of a reference number. ð Press and hold the <TOGGLE> key until you are prompted to load the reference pieces.

ð Your balance suggests the last set reference no. as the reference number. ð Press the <TOGGLE> key until wRef is displayed. ð Press the <TARE> key to enter wRef reference settings. ð Last stored wRef value first digit flashing. Flashing digit indicates that digit value or

place can be changed.

ð Press <TOGGLE> key ( ) to change the value of the Flashing digit. ð Press <CAL> key ( ) to shift the flashing digit from Left to Right ð Press tge <TARE> key to store the wRef value.

Now further weighing in PCS will be with respect to the wRef value.

46

6.1.3 Updating Settings

The Update feature improves the precision of piece counting results. The average piece weight (reference) is recalculated with each reference optimization. Because the new pieces that have been placed in the weighing pan increase the basis for the calculation, the references, and therefore the result of the piece count, are more exact.

Select the UPDATE feature from the reference menu. The reference can be updated by pressing the CAL key which is confirmed by the displaying 'UPDATED' on the display.

Note

• The number of pieces placed in the weighing pan is larger than the reference piece number shown on the display.

• The number of pieces placed in the weighing pan is not greater than twice the most recently saved reference piece number (e.g. If the display shows 100 pcs the added pieces should not be greater than 200).

• Update feature cannot be selected if the previous selected reference was 'wRef'

47

Printouts generated when Unit Toggling is done between Application Unit (Pcs), Unit1 and Unit2 and Reference Weight is changed

When GLP ON

-----------------------------------29-Jul-09 03:46PM Citizen Model CX 220 Ser.no. 9930508 Ver.no. r0.1.04 ID 1234567

-----------------------------------LID: 1000000 NRef 5 pcs WRef 4.00 g Qnt + 5 pcs NRef 50 pcs WRef 0.40 g Qnt + 50 pcs Qnt + 25 pcs NRef 5 pcs WRef 2.00 g Qnt + 5 pcs

-----------------------------------29-Jul-09 03:47PM

Name: ................

------------------------------------

Printouts generated when Unit Toggling is done between Application Unit (Pcs), Unit1 and Unit2 and Reference Weight is changed

When GLP OFF

nRef 5 pcs wRef 2.00 g Qnt + 5 pcs Qnt + 10 pcs nRef 10 pcs wRef 2.00 g Qnt + 10 pcs Qnt + 5 pcs nRef 50 pcs wRef 0.20 g Qnt + 50 pcs Qnt + 100 pcs

If the balance is connected externally to PC or Printer through RS 232 C then, whenever user enter into the reference menu of Piece Counting function & make changes in the reference setting, automatically printout is generated on the Peripheral attached.

In the printout, reference number “nRef” and reference weight “wRef” is printed. After this user can Press Print Key to Print the reading on the display. Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.

48

Note : 1) User cannot enter into the external calibration or menu when GLP is ON

2) To print footer user will have to Press <CANCEL> key.

& footer has not been printed.

Printout: Counting

nRef + 10 : Reference sample quantity wRef + 21.14 g : Reference weight

i.e. weight of one piece

Qnt + 500 pcs : Calculated quantity

The “Percent weighing” function enables you to weigh in to a preset value (1, 10, 20,50, 100%, Free, 100r, 100L, AtroM, AtroD) and to determine deviations from this target value. Percent Weighing (%) presupposes that you have preselected the “F per” function in the menu

Procedure

ðPlace the empty container on the pan. ðPress the <TARE> key to tare the balance. ðPress the <TOGGLE> key briefly until “PER (%)” appears on the display.

Your balance now needs the weight of a reference percent (%).

ðPress and hold the <TOGGLE> key until you are prompted to load the reference

PER (%). ðYour balance suggests the last set reference % as the reference percent (%) You can accept this suggestion or select one of the other reference percent (%)

available (1,10, 20, 50, 100 %, Free, 100r, 100L, AtroM, AtroD) by briefly pressing the

<TOGGLE> key. ðDefault is 1%

The FREE option allows the user to set any reference other than the standard available reference.(Default value is 01.00 % and maximum possible value is 99.99%)

ðNow place reference sample on the pan. ðThen press <TARE> key. Until dashes are displayed, your balance is

calculating the reference

ðAfter your balance has determined the reference weight, it is ready for Percent

Weighing. You can use the <TOGGLE> key at any time to switch the display between the Percent (%) display, weighing unit 1 and weighing unit 2.

Note : The current set weight remains stored until it has been redetermined.

6.2.1 FREE (Reference settings)

The FREE option allows the user to set any reference other than the standard available reference. (Default value is 1.00% and maximum possible value is 99.99%)

Procedure

ðPlace the empty container on the pan. ðPress the <TARE> key briefly to tare the balance. ðPress the <TOGGLE> key briefly until “PER” appears on the display.

Your balance now needs the weight of a reference number. ðPress and hold the <TOGGLE> key until you are prompted to load the reference

pieces.

ðYour balance suggests the last set reference no. as the reference number. ðPress the <TOGGLE> key unit FREE is displayed. ðPress the <TARE> key to enter FREE reference settings. ðLast stored FREE value is displayed. Flashing digit indicates that digit value or

place can be changed.

ðPress <TOGGLE> key ( ) to change the value of the Flashing digit. ðPress <CAL> key ( )to shift the flashing digit from Left to Right ðWhen you have placed exactly the same number of pieces on the weighing pan

as set in the FREE setting, press TARE key.

As soon as the weighing result is stable, the calculated average piece weight is accepted as the reference

50

49

6.2 Percent Weighing (%)

Note : 1) User cannot enter into the external calibration or menu when GLP is ON

2) To print footer user will have to Press <CANCEL> key.

& footer has not been printed.

If the balance is connected externally to PC or Printer through RS 232 C then, whenever user enter into the reference menu of Percent Weighing function & make changes in the reference setting, automatically printout is generated on the Peripheral attached. In the printout, reference percent “pRef” and reference weight “wRef” is printed. After this user can Press Print Key to Print the reading on the display. Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.

Printouts generated when Unit Toggling is done between Application Unit (%), Unit1 and Unit2 and Reference Weight is changed

When GLP ON

When GLP OFF

-----------------------------------29-Jul-10 03:46PM Citizen Model CX 220 Ser.no. 9930508 Ver.no. R0.1.04 ID 1234567

-----------------------------------LID: 1000000 Ref 10.00 % wRef 1.00 g Pct + 10.00 % + 10.0000 g + 50.0000 ct Pct + 20.00 % pRef 1.00 % wRef 20.00 g Pct + 1.00 % Pct + 0.50 %

-----------------------------------29-Jul-10 03:47PM

Name: ................

------------------------------------

Ref 10.00 % wRef 1.00 g Pct + 10.00 % + 10.0000 g + 50.0000 ct Pct + 20.00 % pRef 1.00 % wRef 20.00 g Pct + 1.00 % Pct + 0.50 %

Printout: Counting

pRef 10% : Reference percentage wRef + 21.14 g : Reference weight Pct + 90.34% : Calculated percentage

52

51

6.2.2 Differential Weighing

The Differential Weighing application is used to analyze changes in the weight of one or more samples. The first step is to determine the initial weight of the sample (weighing in). Selected components are then separated from or added to the sample. This includes procedures such as drying, centrifugation, filtering, incineration, vaporization, coating, etc. After the sample has been processed, it is re-weighed (residual weight). The balance then determines the difference between the two weighed values.

100L (Loss)

The moisture content of the sample is displayed (and printed out) as a percentage of the wet weight (= ww = initial weight = 100%). When the results are printed out, the moisture content is designated 100L % " (Loss) (e.g. –11.35 100.00L%) and shown as a negative value.

Dry weight DW – Wet weight WW

100L [0…-100%] = -------------------------------------------- *100%

Wet weight WW

100R (Residue)

The dry content of the sample is displayed (and printed out) as a percentage of the wet weight (= ww = initial weight = 100%). When the results are printed out, the dry content is designated "100R%" (Residue) (e.g. 88.65 100.00R%).

Dry weight DW

100R [100…0%] = -------------------------------------------- *100%

Wet weight WW

AtroM Moisture Content

The moisture content of the sample is displayed (and printed out) as a percentage of the dry weight ( = DW = final weight = 100%). When the results are printed out, the ATRO moisture content is designated “AtroM %" (ATRO Moisture Content) (e.g. –255.33 AtroM %) and shown as a negative value.

Dry weight DW – Wet weight WW

AtroM [0…-1000%] = -------------------------------------------- *100%

Dry weight DW

AtroD Dry Content (Wet weight)

The wet weight of the sample is displayed (and printed out) as a percentage of the dry weight (= DW = final weight = 100%). When the results are printed out, the ATRO dry content is designated “AtroD %" (ATRO Dry Content) (e.g. 312.56 AtroD %).

Wet weight WW

AtroD [100…1000%] = ----------------------------------------- *100%

Dry weight DW

53

100L

100R

AtroM[%]

100L% (Loss Content)

100R% (Residual Content)

%AtroM (Atro Moisture Content)

%AtroD (Atro DryContent)

AtroD [%]

54

Percentage Weighing (%) (in 100R / 100L / AtroM / AtroD)

Percent Weighing (%) presupposes that you have preselected the “F per” function in the menu

Procedure

ðPress the <TARE> key to tare the balance. ðPress the <TOGGLE> key briefly until “PER (%)” appears on the display.

Your balance now needs the weight of a reference percent (%).

ðPress and hold the <TOGGLE> key until you are prompted to load the reference

PER (%). ðYour balance suggests the last set reference % as the reference percent (%) Press the <TOGGLE> key until the following option is displayed (100R / 100L / AtroM

/ AtroD)

ðNow place reference sample on the pan which is to be analyzed (Initial Weight). ðThen press <TARE> key. Until horizontal dashes are displayed, your balance is

calculating the reference. ðAfter your balance has determined the reference weight, it is ready for Percent

Weighing in Differential weighing. ðNow treat the sample which includes process like drying, centrifugation, filtering, incineration, vaporization, coating, etc. After the sample has been processed, re-

weigh it (residual weight). The balance then determines the difference between

the two weighed values.

You can use the <TOGGLE> key at any time to switch the display between the Percent (%) display, weighing unit 1 and weighing unit 2.

Note: If the current measured value on display mode is greater or less than the predefined limit value (i.e. greater than 999.99 % or less than –999.99 %) the balance displays Over range (----Or----)

55

100L% (Loss Content)

(Treat the sample& Re-Weigh it)

Printouts generated when Unit Toggling is done between Application Unit (Per %), Unit1 and Unit2 and Reference Weight is changed

When GLP ON When GLP OFF

----------------------------------28-Jul-10 03:19PM Citizen Model CX 220 Ser.no. 9223102 Ver.no. r0.1.5.3 ID 1234567

----------------------------------LID: 1111111 pRef ATROD % wRef 0.5000 g Pct + 100.00 % Pct + 500.00 % + 50.0000 g + 250.0000 ct

----------------------------------28-Jul-10 03:23PM Name:

................

-----------------------------------

pRef ATROD % wRef 0.5000 g Pct + 100.00 % Pct + 500.00 % + 50.0000 g + 250.0000 ct

If the balance is connected externally to PC or Printer through RS 232 C then, whenever user enter into the reference menu of Percent Weighing function & make changes in the reference setting, automatically printout is generated on the Peripheral attached. In the printout, reference percent “pRef” and reference weight “wRef” is printed. After this user can Press Print Key to Print the reading on the display. Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.

Note : 1) User cannot enter into the external calibration or menu when GLP is ON

2) To print footer user will have to Press <CANCEL> key.

& footer has not been printed.

56

The custom unit feature enables you to perform weighing in a customized unit i.e. weighing can now be performed in a unit other than standard available 15 units.

Procedure

Custom unit presupposes that you have selected the 'F Cust' in the user menu.

ðPlace the empty container on the pan. ðPress the <TARE> key briefly to tare the balance. ðPress the <TOGGLE> key briefly until “CSt” appears on the display.

Your balance now needs conversion factor, accuracy and LSD to perform weighing in custom unit.

ðPress and hold the <TOGGLE> key to browse through the custom unit setting menu.

Your balance suggests the last stored values for the factor, accuracy and LSD.

ðPress the <TARE> key to enter the specific setting.

Factor Setting

The factor value can be set to any user defined value except for zero.

ðPress the <TARE> key to enter the factor setting. ðPress the <TOGGLE> key ( ) to change the value of the flashing digit. ðPress the <CAL> key ( ) to change the flashing digit from left to right. ðPress the <PRINT> key to shift the decimal position in a cyclic way. ðAfter proper setting of factor press the <TARE> key.

Note: Please refer error conditions for errors occurred in storing the Factor, Accuracy and

LSD settings.

Accuracy Setting

ðPress the <TARE> key when the Acc is displayed. ðPress the <TOGGLE> key to browse through the standard available accuracy. ðYou can select any of the standard accuracy with the help of <TARE> key.

Standard accuracies available are

0.000001, 0.00001, 0.0001, 0.001, 0.01, 0.1, 1, 10, 100, 1000

The stability indicator alongside indicates the selected accuracy. The Accuracy Setting is for display purposes and not for calculation of Custom unit.

LSD Setting

ðPress the <TARE> key when LSD is displayed. ðPress the <TOGGLE> key to browse through the standard available LSD's. ðYou can select any of the standard available LSD (Least significant Digit) with the

help of <TARE> key.

Standard LSD's available are

1, 2, 5, 10, 20, 50, 100

The stability indicator alongside indicates the selected LSD.

To store the Factor, Accuracy and LSD values, press and hold the <TARE> key when the display shows Factor or Acc or LSD

The default settings are

Factor = 1.0000 (i.e. 1 gram) Accuracy = 0.01 LSD = 1

57

58

6.3 Custom Unit

E.g. If the settings are as follows, Factor = 1.02356 Accuracy = 0.00 LSD = 50

Now if 50 gm of weight is loaded on the pan the calculation for displayed weight will be as follows, Weight * Factor = 50 * 1.023456 = 51.1728

The displayed weight will be 51.150

The second digit after decimal point will change in multiples of 5 because,

Accuracy * LSD = 50 * 0.001 = 0.05

You can use the <TOGGLE> key at any time to switch the display between custom unit display, weighing unit 1 and weighing unit

2. User can go to Standby mode by pressing on/off key and go to Simple Weighing with unit 1 by Cancel key and balance shows Current weights.

60

Printouts generated when Unit Toggling is done between Application Unit (Cst), Unit1 and Unit2.

When GLP ON When GLP OFF

----------------------------------28-Jul-10 03:19PM Citizen Model CX 220 Ser.no. 9223102 Ver.no. r0.1.5.3 ID 1234567

-----------------------------------

LID: 1111111

Factor 3.023456 Accuracy 0.1 Lsd 2 + 151.2 cst + 50.0000 g + 250.000 ct Factor 1.023456 Accuracy 0.001 Lsd 50 + 61.400 cst + 51.200 cst

----------------------------------28-Jul-10 03:23PM Name:

................

-----------------------------------

Factor 3.023456 Accuracy 0.1 Lsd 2 + 151.2 cst + 50.0000 g + 250.000 ct Factor 1.023456 Accuracy 0.001 Lsd 50 + 61.400 cst + 51.200 cst

If the balance is connected eternally to PC or Printer through RS 232 C then, whenever user enter into the Custom Unit Menu & make changes in the Factor, Accuracy and LSD setting, automatically printout is generated on the Peripheral attached.

In the printout, the new Factor, Accuracy and LSD values are printed. After this user can Press Print Key to Print the reading on the display. Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.

Note : 1) User cannot enter into the external calibration or menu when GLP is ON

2) To print footer user will have to Press <CANCEL> key.

& footer has not been printed.

59

The animal weighing feature enables you to perform weighing of unstable samples (live animals). The balance calculates the weight as the average of a defined number of individual weighing operations.

You can select from the two available animal weighing modes i.e. Auto animal weighing and manual animal weighing.

The weighing unit for animal weighing will be the same as selected for unit 1.

For Animal Weighing Process to start two conditions should be satisfied, the weight of the animal kept on the pan should be higher than 100 display increment i.e. if the balance capacity is 300 gm and accuracy is 0.0001 gm, then in Animal Weighing Process the weight of the animal should be above 100 * 0.0001 g = 0.001g and When two successive weight measured are within predefined tolerance range.

Number of weighing operations for calculation of an average Cnt can be set before the beginning of each series.

Balance returns to the basic weighing mode when unloaded; i.e., when the load is below the unload threshold

The Unload threshold is 50 display intervals.

6.4.1 Manual Animal Weighing

Manual Animal Weighing presupposes that you have selected the 'F Anl' in the user menu.

Procedure

ðPlace the empty container on the pan. ðPress the <TARE> key briefly to tare the balance. ðPress the <TOGGLE> key briefly until “ ”symbol appears on the display.

Your balance now needs to set the countdown value.

ðPress and hold the <TOGGLE> key to enter countdown options. The entire menu can

be accessed by pressing the <TOGGLE> key. The stability symbol indicates the currently selected countdown value.

ðPress the <TARE> key to select specific countdown value. ðKeep the animal on the pan, press the <CAL> key to start the animal weighing process

when both the condition required for animal weighing are met the countdown process will start, when the countdown time ends the average weight on animal is displayed with the display locked with flashing animal symbol.

Locked display is indicated by the flashing animal and AUTO symbol.

The countdown options available are,

• t-5

• t-10 (Default)

• t-20

• t-50

• t-100

You can use the <TOGGLE> key at any time to switch the display between animal weighing, weighing unit 1 and weighing unit 2. User can go to Standby mode by pressing on/off key and go to Simple Weighing with unit 1 by Cancel key and balance shows Current weights.

61

62

6.4 Animal Weighing

6.4.2 Auto Animal Weighing

Auto Animal Weighing presupposes that you have selected the 'F Anl AUTO' in the user menu. Auto animal weighing proves to be beneficial when the balance is used majority for animal weighing and less for simple weighing thus reducing the time required for animal weighing.

Procedure

Place the empty container on the pan. Press the <TARE> key briefly to tare the balance.

Press the <TOGGLE> key briefly until “ ” and “AUTO” symbol appears on the display. Your balance now needs to set the countdown value.

Press and hold the <TOGGLE> key to enter countdown menu. The entire menu can

be accessed by the <TOGGLE> key.

The stability symbol indicates the currently selected countdown value.

Press the <TARE> key to select specific countdown value.

Keep the animal on the pan, when both the condition required for animal weighing

are met the countdown process will start, when the countdown time ends the

average weight on animal is displayed with the display locked. Thus there is no need of pressing a key to start the countdown process in the auto animal weighing mode. Locked display is indicated by the flashing animal and AUTO symbol. The countdown options available are,

t-5 (Auto), t-10 (Auto) Default, t-20 (Auto), t-50 (Auto), t-100(Auto)

You can use the <TOGGLE> key at any time to switch the display between animal weighing, weighing unit 1 and weighing unit 2. User can go to Standby mode by pressing on/off key and go to Simple Weighing with unit 1 by Cancel key and balance shows Current weights.

ð ð ð

ð

ð ð

63

Printouts generated when Unit Toggling is done between Application Unit (Anl), Unit1 and Unit2 and Reference Weight is changed

When GLP ON When GLP OFF

----------------------------------28-Jul-10 03:19PM Citizen Model CX 220 Ser.no. 9223102 Ver.no. r0.1.5.3 ID 1234567

----------------------------------Cnt 20 xNt + 50.0709 g + 50.0715 g + 250.3575 ct xNt + 50.0709 g

----------------------------------28-Jul-10 03:23PM Name:

................

-----------------------------------

Cnt 20 xNt + 50.0709 g + 50.0715 g + 250.3575 ct xNt + 50.0709 g

Printout: Counting

Cnt 20 : Number of subweighing

operations

xNt + 50.0709 g : Calculated Average

If the balance is connected eternally to PC or Printer through RS 232 C then, whenever user enter into the Countdown Menu of Animal Weighing & make changes in the countdown time automatically printout is generated on the Peripheral attached.

In the printout, the new countdown value ’mDef’ is printed. After this user can Press Print Key to Print the reading on the display. Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.

Note : 1) User cannot enter into the external calibration or menu when GLP is ON

2) To print footer user will have to Press <CANCEL> key.

& footer has not been printed.

64

65

6.5.1 Manual Formulation

Manual formulation presupposes that you have selected the 'F Form' in the user menu.

Procedure

Place the empty container on the pan.

ðPress the <TARE> key briefly to tare the balance. ðPress the <TOGGLE> key briefly until Fol is displayed on the display. ðAdd weight on the pan. Weight can be added to summation when ‘ ’ is

displayed on the display i.e. when it is greater than 20d.

ðPress the <CAL> key to store the weight, the balance displays “n-1” indicating that 1st

weight is stored. The weight is tarred automatically and simultaneously print command is given.

E.g. if 9.9968 gm is added the printer output is as follows

N1 : 9.9968 g Tot : +9.9968 g

Further addition of weights will give the following output (addition of 20.0070 gm).

N2 : 20.0070 g Tot : +39.0038 g

ðTo view the total weight, press the <CAL> and <TOGGLE> key together. The print

command is given automatically N2 Tot : + 39.0038 g

66

6.5 Formulation

The formulation feature allows individual weighing values to be summed to a total.

User can select from two available formulation modes i.e. Manual formulation and auto formulation.

Maximum no of weights that can be summed is 99.

Store component weights with

• Display zeroed automatically after value is stored, and

• Automatic printout (print application parameters)

• Of the last component weight (net value) and

• Of the total weight (tare value)

Clear component memory when weighing series is canceled by pressing CANCEL key

Note :

Individual weights can be added into summation only if the weights are greater than 20d, this is indicated by ‘ ’ symbol.

The weighing unit for formulation will be the same as selected.

–

67

Printouts generated when Unit Toggling is done between Application Unit (For), Unit1 and Unit2 and Reference Weight is changed

Printouts generated when Unit Toggling is done between Application Unit (Forl), Unit1 and Unit2 and Reference Weight is changed

When GLP ON When GLP OFF

----------------------------------28-Jul-10 03:19PM Citizen Model CX 220 Ser.no. 9223102 Ver.no. r0.1.5.3 ID 1234567

----------------------------------N1 + 20.0000 g Tot + 20.0000 g + 20.0000 g + 100.0000 ct N2 + 50.0000 g Tot + 70.0000 g N 2 Tot + 70.0000 g

----------------------------------28-Jul-10 03:23PM Name:

................

-----------------------------------

N1 + 20.0000 g Tot + 20.0000 g + 20.0000 g + 100.0000 ct N2 + 50.0000 g Tot + 70.0000 g N 2 Tot + 70.0000 g

Printout Configuration

N1 + 20.0000 g 1st component and its weight Tot + 20.0000 g Sum of components N2 + 50.0000 g 2nd component and its weight Tot + 70.0000 g Sum of components N 2 Total number of components Tot + 70.0000 g Total formulation weight

If the balance is connected eternally to PC or Printer through RS 232 C then, whenever user adds weight to the formulation procedure automatically printout is generated on the Peripheral attached. In the printout, the component added ‘N x ’along with the total sum ‘Tot’ is printed. After this user can Press Print Key to Print the reading on the display. Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.

6.5.2 Auto Formulation

Auto formulation presupposes that you have selected the 'F Form AUTO' in the user menu.

ðPlace the empty container on the pan. ðPress the <TARE> key briefly to tare the balance. ðPress the <TOGGLE> key briefly until Fol and AUTO is displayed on the display. ðAdd weight on the pan. Weight can be added to summation when “ ” is

displayed on the display i.e. when it is greater than 20d.

ðWhen the weight is stable the weight is stored in the formulation procedure and the

balance displays “n-1” indicating that 1st weight is stored. The weight is tarred automatically and simultaneously print command is given. Thus there is no need to press any to start the auto formulation procedure.

You can use the <TOGGLE> key at any time to switch the display between formulation, weighing unit 1 and weighing unit 2. User can go to Standby mode by pressing on/off key and go to Simple Weighing with unit 1 by CANCEL key and balance shows Current weights.

Auto formulation proves to be beneficial when the balance is used in majority for formulation weighing and less for simple weighing thus reducing the time required for formulation as compared to manual formulation.

Note : 1) User cannot enter into the external calibration or menu when GLP is ON

2) To print footer user will have to Press <CANCEL> key.

& footer has not been printed.

68

69

This feature is used to check whether a sample corresponds to a preset target or is with a specific tolerance range.

The results displayed can also be available on external port, which with the help of electronic processing can be used to control additional devices.

The check weighing procedure will always be carried out in unit 'gm'.

Check weighing presupposes that you have selected the 'F CHw' in the user menu.

Procedure

ðPress the <TARE> key briefly to tare the balance. ðPress the <TOGGLE> key briefly until “CW” is displayed on the display.

Your balance now needs the target and tolerance values. If entering the check weighing for the first time the target and tolerance setting menu will be displayed.

Target and Tolerance Settings

ðPress and hold the <TOGGLE> until the target and tolerance setting menu is

prompted.

ðPress the <TOGGLE> key to browse through the TARGET, HI, and LOW setting. ðPress the <TARE> key to enter specific setting. ðPress the <TOGGLE> key ( ) to change the value of the flashing digit. ðPress the <CAL> key ( ) to change the flashing digit from left to right. ðAfter proper setting of values press the <TARE> key. ðPress and hold the <TARE> key to store the values of target and tolerance values.

Note: To view the weight when the balance displays LL or HH press the <CAL> key press

the <CAL> key again to display LL or HH.

70

6.6 Check Weighing

Printouts generated when Unit Toggling is done between Application Unit (Chw), Unit1 and Unit2 and Reference Weight is changed

When GLP ON When GLP OFF

----------------------------------28-Jul-10 03:19PM Citizen Model CX 220 Ser.no. 9223102 Ver.no. r0.1.5.3 ID 1234567

----------------------------------Target 150.0000 g Hi 160.0000 g Lo 140.0000 g

-------LL------- + 99.9979 g + 149.9979 g

-------HH------- + 200.0029 g

----------------------------------28-Jul-10 03:23PM Name:

................

-----------------------------------

Target 150.0000 g Hi 160.0000 g Lo 140.0000 g

-------LL------- + 99.9979 g + 149.9979 g

-------HH------- + 200.0029 g

If the balance is connected eternally to PC or Printer through RS 232 C then, whenever user enter into the Target and Tolerance Setting Menu of Check Weighing Menu & make changes in the setting, automatically printout is generated on the Peripheral attached.

In the printout, Target and Tolerance value are printed. After this user can Press Print Key to Print the reading on the display. Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.

Note : 1) User cannot enter into the external calibration or menu when GLP is ON

2) To print footer user will have to Press <CANCEL> key.

& footer has not been printed.

Load the weight on the pan and the balance will display the results according to the preset values of target and tolerance.

E.g. If the values are as follows,

TARGET = 150.0000 gm HI = 155.0000 gm LOW = 145.0000 gm

Now if 144.0000 gm is loaded on the pan the display shows LL indicating that the loaded weight is less than the low value set.

If 156.0000 gm is loaded on the pan the display shows HH indicating that the loaded weight is greater than the high value set.

While the balance displays LL or HH the buzzer will beep continuously to indicate that the weight is out of the tolerance band and the corresponding lines on the external will be enabled.

If the weight is in the tolerance range the balance will display the weight similar to simple weighing.

You can use the <TOGGLE> key at any time to switch the display between check weighing, weighing unit 1 and weighing unit 2.

User can go to Standby mode by pressing on/off key and go to Simple Weighing with unit 1 by CANCEL key and balance shows Current weights.

For High Range

For Low Range

71

72

73

The totalization procedure allows individual weighing pieces to be summed to a total.

User can select from two available formulation modes i.e. Manual totalization and auto totalization. Maximum no of weights that can be summed is 99.

Individual weights an be added into summation only if the added pieces is greater

than 2, this is indicated by “ ” symbol.

6.7.1 Manual Totalization

Procedure

Manual totalization presupposes that you have selected the 'F tot' in the user menu.

ð Place the empty container on the pan. ðPress the <TARE> key briefly to tare the balance. ðPress the <TOGGLE> key briefly until “tot” is displayed on the display.

Your balance now needs the weight of a reference number.

ðPress and hold the <TOGGLE> key until you are prompted to load the reference pieces.

Store component pieces with

• Display zeroed automatically after value is stored, and

• Automatic printout (print application parameters)

• Of the last added pieces and

• Of the total number of pieces.

Clear component memory when weighing series is canceled by pressing CANCEL key

Note:

-

ðYour balance suggests the last set reference no. as the reference number.

You can accept this suggestion or select one of the other reference numbers available

(5, 10, 20, 50, 100 pieces) by briefly pressing the <TOGGLE> key.

ðNow place the selected number of reference pieces on the pan. ðWhen you have placed exactly the same number of pieces on the weighing pan as

selected reference pieces press TARE key.

As soon as the weighing result is stable, the calculated average piece weight is

accepted as the reference. ðAdd weight on the pan. Weight can be added to summation when “ ” is

displayed on the display i.e. when number of pieces is greater than 2.

st

ðPress the <CAL> key to store the weight, the balance displays “n-1” indicating that 1

weight is stored. The weight is tared automatically and simultaneously print command is

given.

E.g. if 20.0000 gm and the reference is selected as 5, the printer output is as follows

nRef 5 pcs

wRef 4 g

N1 + 5 pcs

Tot + 5 pcs

Further addition of weights will give the following output (addition of 10.0000 gm).

N2 + 2 pcs

Tot + 7 pcs ð To view the total weight, press the CAL and NEXT key together. The print command is

given automatically

N 2

Tot + 7 pcs

74

6.7 Totalization

75

Printouts generated when Unit Toggling is done between Application Unit (Tot), Unit1 and Unit2 and Reference Weight is changed

When GLP ON When GLP OFF

------------------------------28-Jul-10 03:19PM Citizen Model CX 220 Ser.no. 9223102 Ver.no. r0.1.5.3 ID 1234567

-------------------------------

------------------------------28-Jul-10 03:23PM Name:

................

-------------------------------

nRef 10 pcs wRef 2.0000 g N1 + 10 pcs Tot + 10 pcs N2 + 25 pcs Tot + 35 pcs N3 + 10 pcs Tot + 45 pcs N 3 Tot + 45 pcs

If the balance is connected externally to PC or Printer through RS 232 C then, whenever user enter into the reference menu of Totalization function & make changes in the reference setting, automatically printout is generated on the Peripheral attached.

In the printout, reference number “nRef” and reference weight “wRef” is printed. After this user can Press Print Key to Print the reading on the display. Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.

6.7.2 Auto Totalization

Auto totalization presupposes that you have selected the 'F tot AUTO' in the user menu.

totalization totalization

totalization

Procedure

ðPlace the empty container on the pan. ðPress the <TARE> key briefly to tare the balance. ðPress the <TOGGLE> key briefly until “tot” and AUTO is displayed on the display.

Your balance now needs the weight of a reference number.

ðPress and hold the <TOGGLE> key until you are prompted to load the reference pieces. ðYour balance suggests the last selected reference number.

You can accept this suggestion or select one of the other reference numbers available (5, 10, 20, 50, 100 pieces) by briefly pressing the <TOGGLE> key.

ðNow place the selected number of reference pieces on the pan. ðWhen you have placed exactly the same number of pieces on the weighing pan as

selected reference pieces press TARE key. As soon as the weighing result is stable, the calculated average piece weight is accepted as the reference.

ðAdd weight on the pan. Weight can be added to summation when “ ” is

displayed on the display i.e. when number of pieces is greater than 2.

ðWhen the weight is stable the number of pieces is stored in the totalization procedure

st

and the balance displays “n-1” indicating that 1 weight is stored. The weight is tarred automatically and simultaneously print command is given. Thus there is no need to press any to start the auto totalization procedure.

Note : You can use the <TOGGLE> key at any time to switch the display between totalization, weighing unit 1 and weighing unit 2. User can go to Standby mode by pressing on/off key and go to Simple Weighing with unit 1 by CANCEL key and balance shows Current weights.

Auto proves to be beneficial when the balance is used in majority for weighing and less for simple weighing thus reducing the time required for as compared to manual

Note : 1) User cannot enter into the external calibration or menu when GLP is ON has not been printed.

2) To print footer user will have to Press <CANCEL> key.

& footer

76

77

Liquid Setting

You can select from the three available options i.e. water, ethanol and other.

Press the <TOGGLE> key to change the liquid option. After proper selection of the liquid setting the <TARE> key.

The default option is distilled water.

Mode Setting

You can select from three options i.e. compensated, uncompensated and purity of gold.

Press the <TOGGLE> key to change the Mode setting. After proper selection of mode press the <TARE> key .

The default option is compensated.

The results of purity of gold will be shown in carats.

ð ð

The density is determined applying the principle of Archimedes, which states that any body immersed in a fluid becomes lighter by an amount equal to the weight of the fluid that it has displaced. Purity of gold can also be determined on the basis of density.

The weighing unit of density determination will be 'grams'.

Density determination presupposes that you have selected the 'F Den' in the user menu.

To calculate the density of sample, the balance should know the type of liquid and its temperature, used to calculate the density of solid.

Procedure

Press and hold the <TOGGLE> until the functionality menu is prompted. Press the <TOGGLE> key to browse through the Temperature, Liquid and Mode settings.

Temperature Setting

Press the <TARE> key when the 'temp' is displayed. Press the <TOGGLE> key ( ) to change the value of the flashing digit. Press the <CAL> key ( ) to change the flashing digit from left to right. After proper setting of values press the <TARE> key. The default value of temperature is 25.0ºC This setting is alterable only when the liquid selected is water or ethanol. If the liquid selected is 'Other' the temperature setting will ‘nA’ i.e. Not applicable.

ð ð

ð ð ð ð ð ð

78

6.8 Density Determination

79

Density Determination Procedure

ð ð ð ð

ð

Attach the Density determination Kit to the Balance Press the <TARE> key briefly to TARE the balance. Press the <TOGGLE> key briefly until “Den” appears on the display. Press the <CAL> key to start the density determination procedure. The Balance now asks for weight of the sample in air. (With Wt.Air flashing on the display every 10 seconds) Place the sample on density determination kit, When the weight is stable press the CAL key to accept the weight of sample in air. Now the balance asks for the weight of sample in liquid (With Wt.Liqd flashing on the display every 10 seconds) Now immerse the sample in the liquid, When the weight is stable press the CAL key to accept the weight of sample in liquid.

The balance will show the results upon the selected mode i.e. compensated, uncompensated or gold.

Density Calculations

With compensation for air density

ñ = A * (ñ0 - ñl)

+ ñl

(A - B)

ñ = density of sample A = weight of sample in air B = weight of sample in auxiliary liquid ñ0 = density of auxiliary liquid ñl = air density (0.0012 g/cm3)

e.g.

ñ = (A / (A - B)) (ñ0 - ñl) + ñl = (20.000 / (20.000-18.935)) (0.99689 – 0.0012) + 0.0012 = 18.699 g/cm3

Without compensation for air density

ñ = A

ñ0

*

(A - B)

ñ = ñ0 (A / (A - B)) e.g.

ñ = ñ0 (A / (A - B)) = (20.000 / (20.000-18.935)) (0.99689) = 18.721 g/cm3

Add Wt. in Air

Add Wt. in Liquid

Display for compensated density

Display for uncompensated density

80

81

Printouts generated when Unit Toggling is done between Application Unit (Den with Compensated Mode Liquid as Ethanol), Unit1 and Unit2 and Reference Weight is changed

Printouts generated when Unit Toggling is done between Application Unit (Den with Uncompensated Mode and Liquid as None), Unit1 and Unit2 and Reference Weight is changed

When GLP ON When GLP ON

----------------------------------28-Jul-10 03:19PM Citizen Model CX 220 Ser.no. 9223102 Ver.no. r0.1.5.3 ID 1234567

-----------------------------------

----------------------------------28-Jul-10 03:23PM Name:

................

-----------------------------------

Mode COMPENSATED Liquid ETHANOL Temperature 28.0 Den + 0.6995g/c3 + 18.9350 g + 94.675 ct

----------------------------------28-Jul-10 03:19PM Citizen Model CX 220 Ser.no. 9223102 Ver.no. r0.1.5.3 ID 1234567

-----------------------------------

----------------------------------28-Jul-10 03:23PM Name:

................

-----------------------------------

Mode UNCOMPENSATED Liquid OTHER Temperature NA Den + 0.6994g/c3 + 18.9350 g + 94.675 ct

Printouts generated when Unit Toggling is done between Application Unit (Den), Unit1 and Unit2 and Reference Weight is changed

When GLP ON When GLP OFF

----------------------------------28-Jul-10 03:19PM Citizen Model CX 220 Ser.no. 9223102 Ver.no. r0.1.5.3 ID 1234567

-----------------------------------

----------------------------------28-Jul-10 03:23PM Name:

................

-----------------------------------

Mode GOLD Liquid WATER Temperature 25.0 Pur + 23.1 ct + 18.9350 g + 94.675 ct

If the balance is connected externally to PC or Printer through RS 232 C then, whenever user enter into the menu of Density function & make changes in the, automatically printout is generated on the Peripheral attached.

In the printout, Temperature, Liquid and Mode are printed. After this user can Press Print Key to Print the reading on the display. Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.

If the balance is connected externally to PC or Printer through RS 232 C then, whenever user enter into the menu of Density function & make changes in the, automatically printout is generated on the Peripheral attached.

In the printout, Temperature, Liquid and Mode are printed. After this user can Press Print Key to Print the reading on the display. Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.

Note : 1) User cannot enter into the external calibration or menu when GLP is ON

2) To print footer user will have to Press <CANCEL> key.

& footer has not been printed.

Note : 1) User cannot enter into the external calibration or menu when GLP is ON

2) To print footer user will have to Press <CANCEL> key.

& footer has not been printed.

82

83

Note: To enter the settings below, it is assumed that the user has already performed the above procedure and the scale is in F PiP mode.

Count Cycle Settings

ð Press <TOGGLE> key to enter F PiP settings. ð Press < TARE> to enter the count settings. ð ‘n’ represents the number of calibration cycles the user intends to perform. ‘n’ can have any value between 5 and 15 (including both).

ð Press <TOGGLE> to select the required value of ‘n’. ð Press <TARE> once to select the value of ‘n’ and return to F PiP settings. ð The default count value is 5.

Temperature settings

ð Press <TOGGLE> key to enter F PiP settings. ð Select ‘tEMP’ in F PiP settings by pressing <TOGGLE> key. ð Press < TARE> to enter the ‘tEMP’ settings. ð The user can select from a list of 30 predefined temperatures ranging from 15.0ºC to

30.0ºC with a step interval of 0.5ºC. ð Change the temperature value by pressing <TOGGLE> key and then select it pressing <TARE>. This will bring you back to F PiP settings. ð The default temperature is 25.0ºC

Pressure Settings

ð Press <TOGGLE> key to enter F PiP settings. ð Select ‘PrES’ in F PiP settings by pressing <TOGGLE> key. ð Press < TARE> to enter the ‘PrES’ settings. ð The user can select from a list of 7 predefined pressures ranging from 800 hPa to 1050

hPa with step interval of 50 hPa. ð Change the pressure value by pressing the <TOGGLE> key and then select it pressing <TARE>. This will bring you back to ‘FPiP’ settings. ð The default pressure is 800 hPa.

In laboratories, where pipettes are used for experimenting with liquids, it becomes important to calibrate the pipette. Thus this feature enables the user to calibrate the pipette. The feature “pipette calibration” can be activated by selecting the “F PiP” function in the menu. By pressing the CAL/MENU key for 4 seconds the user can enter the User menu and select the “F PiP” function. Note: The below procedure presupposes that you have selected the ‘F PiP ‘function in the user menu.

Procedure

ð Place the empty container on the pan. ð Press the < TARE> key briefly to tare the balance. ð Press the <TOGGLE> key for 2 seconds to enter the F PiP function.

84

6.9 Pipette Calibration

85

Note:

ðIt is assumed that the user has already performed the above procedure and the s c a l e

is in F PiP mode.

ðWhen the pipette calibration procedure process has not started the system will

perform normal weighing with the unit as gm.

Calibration procedure:

ðThe calibration procedure repeats itself 'n' times where 'n' is the count entered in the

count cycle settings (in FPiP settings).

ðOnce in F PiP mode, press the <CAL/MENU> key to start the calibration process. ðOnce the <MENU/CAL> key is pressed, it will ask for the initial volume V

0.

ðFor a calibration procedure of 'n' times, the scale will ask for V 'n' times. Each of these

0

value will be stored as 'PLACE n'.

st

ðThus, for the 1 time, place the initial volume and press <CAL/MENU> key once the

stability is achieved. This is accepted as 'PLACE 1'.

ðFollow the above procedure for 'PLACE 1' to 'PLACE n'. ðRepeat the above procedure for half volume V and full volume V each 'n' times

half full

respectively.

ðIn case of a successful calibration the scale will display 'PiP done'. If not, then it will

ask to repeat the step wrongly performed.

Volume Settings:

Initial volume V

0:

ðPress <TOGGLE> key to enter F PiP settings. ðSelect 'V ' in F PiP settings by pressing <TOGGLE> key.

0

ðPress < TARE> to enter the 'V ' settings.

0

ðThe user can change the volume with the help of <CAL/MENU> key and <TOGGLE>key. ðPressing the <CAL/MENU> key will shift the cursor to the right in a cyclic way and pressing

the <TOGGLE> key will increment the digit.

ðPress the <TARE> key to select the value. This will bring you back to the F PiP menu ðThe default volume is, V = 10.00 uL

0

Half volume V

Half :

ðPress <TOGGLE> key to enter F PiP settings. ðSelect 'V ' in F PiP settings by pressing <TOGGLE> key.

Half

ðPress < TARE> to enter the 'V ' settings.

Half

ðThe user can change the volume with the help of <CAL/MENU> key and <TOGGLE>key. ð Pressing the <CAL/MENU> key will shift the cursor right in a cyclic way and pressing the

<TOGGLE> key will increment the digit.

ðPress the <TARE> key to select the value. This will bring you back to the F PiP menu ðThe default volume is, V = 11.00 uL

Half

Full volume, V

Full. :

ðPress <TOGGLE> key to enter F PiP settings. ðSelect 'V ' in F PiP settings by pressing <TOGGLE> key.

Full.

ðPress < TARE> to enter the 'V ' settings.

Full.

ðThe user can change the volume with the help of <CAL/MENU> key and <TOGGLE>key. ð Pressing the <CAL/MENU> key will shift the cursor right in a cyclic way and pressing the

<TOGGLE> key will increment the digit.

ðPress the <TARE> key to select the value. This will bring you back to the F PiP menu ðThe default volume is, V = 12.00 UL.

Full

86

87

88

PIPETTE CAL. RESULTS

Count : 5 Cnt Temp. : 15.0 °C Pressure : 800 hPa Results : Vmin

1 10016.45 uL 2 10016.45 uL 3 10016.35 uL 4 10016.35 uL 5 10016.35 uL

Vmin = 10.00 uL Va = 10016.39 uL Es = 10006.39 uL Es% = 100063.88 % Sr = 0.05 uL CV = 0.00 %

------------------------

Results : V1/2

1 15023.12 uL 2 15023.12 uL 3 15024.42 uL 4 15024.42 uL 5 15024.12 uL

V1/2 = 11.00 uL Va = 15023.84 uL Es = 15012.84 uL Es% = 136480.37 % Sr = 0.67 uL CV = 0.00 %

------------------------

Results : Vmax

1 20032.40 uL 2 20032.30 uL 3 20032.30 uL 4 20032.20 uL 5 20032.20 uL

Vmax = 12.00 uL Va = 20032.28 uL Es = 20020.28 uL Es% = 166835.63 % Sr = 0.08 uL CV = 0.00 %

-----------------------Legend

Va : Mean Value Es : Systematic Error Es% : Es expressed as % of nominal value Sr : Standard Deviation CV : Coefficient of Variation

------------------------

11-Apr-11 00:18

Citizen

Model 00Ct603 Ser.no. 1012652 Ver.no. r0.1.5.8 ID 1234567

-----------------------PIPETTE CAL. RESULTS

Count : 5 Cnt Temp. : 15.0 °C Pressure : 800 hPa

Results : Vmin

1 10016.45 uL 2 10016.15 uL 3 10015.75 uL 4 10015.75 uL 5 10015.65 uL

Vmin = 10.00 uL Va = 10015.95 uL Es = 10005.95 uL Es% = 100059.47 % Sr = 0.34 uL CV = 0.00 %

------------------------

Results : V1/2

1 15023.82 uL 2 15023.62 uL 3 15023.62 uL 4 15023.62 uL 5 15023.72 uL

V1/2 = 11.00 uL Va = 15023.68 uL Es = 15012.68 uL Es% = 136478.92 % Sr = 0.09 uL CV = 0.00 %

------------------------

Results : Vmax

1 20031.89 uL 2 20031.89 uL 3 20031.89 uL 4 20031.59 uL 5 20031.59 uL

Vmax = 12.00 uL Va = 20031.77 uL Es = 20019.77 uL Es% = 166831.45 % Sr = 0.16 uL CV = 0.00 %

-----------------------Legend

Va : Mean Value Es : Systematic Error Es% : Es expressed as % of nominal value Sr : Standard Deviation CV : Coefficient of Variation

-----------------------11-Apr-11 00:18 Name:

................

------------------------

WITH GLP OFF

WITH GLP ON

If the balance is connected externally to PC or Printer through RS 232 C then, whenever user enter into the menu of Pipette Calibration & make changes in it, automatically printout is generated on the Peripheral attached.

The following are the parameters that are Printed along with the readings :

If the balance is connected externally to PC or Printer through RS 232 C then, whenever user enter into the menu of Pipette Calibration & make changes in it, automatically printout is generated on the Peripheral attached.

The following are the parameters that are Printed along with the readings :

89

With this feature, the user can obtain the statistics of the data stored in the scale. These statistics includes the details such as number of readings 'n', Average, Minimum value, Maximum value, Standard deviation, Difference and Co efficient of Variance. The feature 'F StAt' can be activated by selecting the 'F StAt' function in the menu. This can be done by pressing the <CAL/MENU> key for 4 seconds and changing the feature by <TOGGLE> key. Press <TARE> key to select 'F StAt'. press <TARE> for 2 seconds to store the selection. The below procedure presupposes that you have selected the 'F StAt' function in the user menu.

Procedure

ðPlace the empty container on the pan. ðPress the < TARE> key briefly to tare the balance. ðPress the <TOGGLE> key for entering the 'F StAt' function.

Note: To use the 'F StAt' function, it is assumed that the user has already performed the above procedure and the scale is in 'F StAt' mode.

Statistics procedure

ðThe user can now place weight on the pan and press the <CAL/MENU> key once

the stability is achieved.

ðThe scale should display 'n-1' (where 'n' is the number of the current weight) and will

retain this as first weight.

ð“rmv” will be displayed on screen for 2 seconds to instruct the user to unload the

weight.

ðThe next weight will be taken into statistics only after user has taken off the weight

from the pan, such that the weight on the pan should now be 0.0000g.

ðRepeat the above procedure for rest of the data entries.

90

6.10 Statistics

91

Reading the statistics

ðAt any point of time, the user can press and hold the <TOGGLE> key for 2 seconds to

go through the statistics.

st

ðThe screen will display the 1 parameter as number of readings 'n' along with the star

symbol which indicates that the user is in the statistics result mode.

ðThe user can now go through the other parameters such as average, Min value, M a x

value, Standard deviation, Difference, Co efficient of Variance by pressing the <TOGGLE> key.

ðThe user can come out of the statistics mode by pressing the < CANCEL > key.

Deleting statistics:

ðThe user can delete the statistics by pressing the <TARE> key for 2 seconds when in

'StAt' mode.

ðThis will delete the previous data entries and start again. ðThe entire data is will be sent to the terminal or to the printer before it gets deleted.

Note:

ðThe minimum weight on the pan should be 10d (where'd' is the accuracy of the

scale), if less than that, then the weight will not be taken into consideration for calculating statistics.

ðThe statistics will be deleted if the system goes into standby mode (i.e. if the auto-off

feature is active or by power on-off).

ðThe user can also print the statistics by pressing the <PRINT> key when in 'StAt' mode.

----------------------------------28-Jul-10 03:19PM Citizen Model CX 220 Ser.no. 9223102 Ver.no. r0.1.5.3 ID 1234567

----------------------------------- 1 + 1.5750 g 2 + 2.3500 g 3 + 7.8950 g 4 + 4.1750 g

----------------------------------n4 max 7.8950 g min 1.5750 g avg 3.9987 std 2.8169 var 7.9349

----------------------------------28-Jul-10 03:23PM Name:

................

-----------------------------------

----------------------------------- 1 + 1.5750 g 2 + 2.3500 g 3 + 7.8950 g 4 + 4.1750 g

----------------------------------n4 max 7.8950 g min 1.5750 g avg 3.9987 std 2.8169 var 7.9349

-----------------------------------

WITH GLP ON WITH GLP OFF

92

If the balance is connected externally to PC or Printer through RS 232 C then, whenever user enter into the menu of Statistics & presses in the print key , the user can obtain the list of parameters shown in the below example :

93

Key Functionality in parameter settings mode

7. Parameter Settings

The following section explains key functionality in parameter settings mode.

To Change Time Format (AM / PM / 24 hours) in Time Settings

Change Sub Menu Setting

Store and quit menu (Auto Cal Menu)

Confirm Setting

Press briefly Press & Hold

Increments the value of digit

Change Main menu options

Shifts the digit from left to right

Quit the Current Parameter Menu

ID / LID SETTINGS

TIME DATE SETTINGS

TIME

DATE

TIME

0

0.5 C

1

0

C

2

0

C

5

0

C

OFF

AUTOCAL SETTINGS

0.5 Hr

1 Hr

3 Hr

24 Hr

OFF

TEMP.

P CAL ON

P CAL OFF

AUTOCAL OFF

AUTO CAL ON

ID

LID

94

On / Off key

Toggling key

Tare keyCancel / Footer

Print key

CAL /

Menu key

Parameter Settings

By accessing the parameter menus the user can change the following settings.

• ID and LID settings.

• Time and Date Settings.

• Auto Calibration and Power On Calibration Settings.

Operating Instructions

These menus can be accessed by pressing the PRINT key or CAL key when all the

characters of the display when coming out of stand by mode or Power On.

95

ID & LID SETTINGS

TIME & DATE SETTINGS

AUTO CAL SETTINGS

& POWER ON

In this menu, User can set the Clock.

Clock setting consist of 2 settings. They are

TIME : In this submenu user can set the time in hours, minutes & seconds

AM, PM & 24 hrs.

DATE : In this submenu user can set the date, Month & Years

Operating Instructions

ð Press the PRINT key for 2 sec when coming out from stand by

or Power on mode.

7.1.1 SET TIME

ð Current Time is displayed with first digit flashing. Flashing digit indicates that digit

value or place can be changed.

ð Press TOGGLE key ( ) to change the value of the Flashing digit.

ð Press CAL key ( ) to shift the flashing digit from Left to Right

ð After proper setting of time in hours, minutes & seconds respectively

for zeroes starting from left, press Tare key

ð Press the PRINT key to Change the format AM, PM & 24hrs.

96

7.1 Time & Date Setting

7.1.2 SET DATE

ð Press TARE key, “date” is display

ð Press TARE key, current date is displayed with first digit flashing. Flashing digit indicates

that digit value or place can be changed.

ð Press TOGGLE key ( ) to change the value of the Flashing digit.

ð Press CAL key ( ) to shift the flashing digit from Left to Right

ð After proper setting of date in day, month & year respectively for zeroes starting from left,

ð Press TARE key to set the date

In this menu user can set the identification number & Lot Identification number.

Operating Instructions

ð Press the PRINT key briefly when coming out from stand by or Power on mode.

7.2.1 SET ID

ð Last stored ID is displayed with first digit flashing. Flashing digit indicates that digit

value or place can be changed.

ð Press TOGGLE key ( ) to change the value of the Flashing digit.

ð Press CAL key ( ) to shift the flashing digit from Left to Right

ð Press the TARE key to store ID Value

7.2.2 SET LID

ð Last stored LID is displayed with first digit flashing. Flashing digit indicates that digit

value or place can be changed.

ð Press TOGGLE key ( ) to change the value of the Flashing digit.

ð Press CAL key ( ) to shift the flashing digit from Left to Right

ð Press the TARE key to store LID Value

97

98

7.2 ID / LID Setting

7.3.2 Auto CAL Temperature Settings

Select Auto CAL ON and press the <TARE< key, now press the <TOGGLE> key when the

LCM displays TIME, press the <TARE> key to enter temperature settings.

0

User can set temp. value = 0.5 C.

0

User can set temp. value = 1 C.

0

User can set temp. value = 2 C.

0

User can set temp. value = 5 C.

User can set temp. value = OFF

Auto Cal triggered due to temp. change will take place irrespective of CAL test is On

or oFF

Note : The Above setting is available with balances with internal calibration.

100

ð Auto Internal Calibration can be triggered automatically, by the following

• Time

• Temperature

• Power on Calibration

Operating Instruction

ð Press the CAL key briefly when coming out from stand by or Power on mode.

7.3.1 Auto CAL Time Settings

Select Auto CAL ON and press the <TARE> key, now press the <TARE> key when the

Displays shows TIME to enter time settings.

User can set time value = 0.5 hrs.

User can set time value = 1 hrs.

User can set time value = 2 hrs.

User can set time value = 3 hrs.

User can set time value = 24 hrs.

User can set time value = OFF

Auto Cal triggered due to time will take place irrespective of cal test on or OFF

Note : The Above setting is available with balances with internal calibration.

99

7.3 Auto Calibration

102

The windows direct communication function enables you to send the data from the balance directly to any windows application program for e.g. Microsoft word, excel etc.

The printer settings in the user menu will be applicable to the windows direct communication also i.e. Data Transfer Mode, Baud rate, Parity, Stop Bit and GLP

The settings attributed to windows direct communication are

• Unit ON or OFF.

• Separator type ENTER or TAB.

To enable windows direct communication, make sure that you have turned it on from the windows side as well.

Enter control panel. Open ACCESSIBILITY OPTIONS from control panel. In the general tab turn on serial key option. Set the baud rate and COM port from the settings option.

ð ð

ð

7.3.3 Power on Calibration

Press the CAL key when the LCM displays Auto CAL On or Off enter Power ON

calibration options.

This setting enables the user to turn on or turn off power on calibration.

Power on calibration will take place every time the balance is powered on.

Power on Cal will take place irrespective of whether CAL Test is On or Off.

Note : The Above setting is available with balances with internal calibration.

101

ð

Click OK to accept the settings for

serial key.

Click APPLY and then OK to save the Accessibility options.

7.4 Windows Direct Communication

103

Windows direct communication settings (Balance Side)

Press and hold the <PRINT> key in simple weighing mode until the windows print menu is prompted.

Press the <TOGGLE> key briefly to change the windows option to ON of OFF. The default option is OFF.

Windows Unit settings

Select Windows print option as ON and press the <TARE> key, now press the <TARE> key when the LCM displays UNIT to enter unit settings.

User can set Unit option as ON (Along with the numerical value the unit will also be sent to windows).

User can set Unit option as OFF (Only the numerical value will be sent to windows and not the unit).

ð

Windows Separator settings

Select Windows print option as ON and press the <TARE> key, now press the <TARE> key when the LCM displays 'Separat' to enter Separator settings.

User can set SEPERATOR option as ENTER (After every value printed on the windows side an ENTER command is given so every subsequent data will print on new line, in Excel every new data will be printed in new row).

User can set SEPERATOR option as TAB (After every value printed on the windows side a TAB command is given so every subsequent data will printed with tab, in Excel every new data will be printed in new column).

104

Features

You can have the parameters pertaining to the ambient weighing conditions printed before (GLP header) and after (GLP footer) the values of a weighing series. These parameters include:

GLP header: – Date – Time at beginning of measurement – Balance manufacturer – Balance model – Balance serial number – Software version number – Identification number of the current sampling operation

GLP footer: – Date – Time at end of measurement – Field for operator signature

The record is output to a CITIZEN data printer or a computer.

Settings

Set print option to request & GLP ON

Function Keys

Press the Print key to output header and first measured value.

End an Application: Output GLP Footer : Press Cancel Key End an application program Press Cancel key

------------------------ Dotted line 28-Jul-10 03:19PM Date / Time (beginning of measurement) Citizen Balance Manufacturer Model CX 220 Balance Model Ser.no. 9223102 Balance Serial Number Ver.no. r0.1.5.3 Software Version ID 1234567 ID

------------------------ Dotted line LID: 1111111 Lot ID nRef 170 pcs Counting : Reference Sample Quantity wRef 0.2945 g Counting : Reference Weight Qnt + 170 pcs Counting Result + 50.0650 g Weighing Result + 250.3250 ct Weighing Result

------------------------ Dotted line 28-Jul-10 03:23PM Date / Time (end of measurement) Name: Name of Operator

................

------------------------ Dotted line

------------------------ Dotted line 20-Jul-10 10:32AM Date / Time (beginning of measurement) Citizen Balance Manufacturer Model CX 220 Balance Model Ser.no. 9223102 Balance Serial Number Ver.no. r0.1.5.3 Software Version ID 1234567 ID

------------------------ Dotted line Calibration: External Calibration / Adjustment Mode

Blank Line W-ID Temperature Set + 200.0000 g Calibration Weight Diff. + 0.1234 g Diff. After Calibration External Cal Done Confirmation of Completed Calibration

Blank Line Diff. 0.0000g Difference from Nominal Value after Calibration

------------------------ Dotted line 20-Jul-10 10:32AM Date / Time (end of measurement) Name: Name of Operator

................

------------------------ Dotted line

The ISO/GLP-compliant record can contain the following lines:

............ Weight ID

32.905'C Temperature

The ISO/GLP-compliant record can contain the following lines:

105

106

8. ISO/GLP-compliant Printout/Record

The following characters can be output, depending on the characters displayed on the balance :

Normal Operation Position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

****+DDDDDDDDDDDDDDD* UUULFCR

or ****-DDDDDDDDDDDDDDD* UUULFCR

or l l l * + DDDDDDDDDDDDDDD* UUULFCR

* : Space CR : Carriage Return D : Digit or letter LF : Line Feed U : Unit Symbol l : ID code Character

Special Codes Position 1 234567891011121314151617181920212223242526

-------OL------ LFCR

or -------UL------ LFCR

or -------Or------ LFCR

-------LL------ LFCR

-------HH------ LFCR

OL : Space UL : Carriage Return Or : Digit or letter LL : Line Feed HH : Unit Symbol

107

Purpose

Your balance is equipped with an interface port for connection to a computer or other peripheral device. You can use an on-line computer to change, start and/or monitor the functions of the balance and theapplication programs.

Features

• Type of interface: Serial interface

• Operating mode: Full duplex

• Standard: RS-232

• Transmission rates: 300; 600; 1,200; 2,400; 4,800; 9,600; 19,200 baud 57600

• Parity: Mark, space, odd, even, none

• Character format: 1 start bit, 8-bit ASCII, parity,1 or 2 stop bits

• Handshake: None

• Data output format of the balance : 26 characters

Factory settings:

Transmission rate: 1,200 baud (9600)

Parity: Odd (none)

Stop bits: 1 stop bit

Handshake: None

Print manually/automatically: Manual at stability

Preparation

• See “Pin Assignments”

108

9. Data Interface

9.1 Output Format with 26 Characters

Data Output Examples + 123.4567 g

Position 1234567891011121314151617181920212223242526

+ 123. 4567 gLFCR

or + 617. 2835 ct LFCR

or N1 + 20. 0000 gLFCR

or Tot + 60. 0000 gLFCR

Position 1 - 4 : ID code Character or Space Position 5 : Sign Position 6 - 20 : Weight with Decimal Point; leading zeros = space Position 21 : Space Position 22 - 24 : Unit Symbol or Space Position 25 : Line Feed Position 26 : Carriage Return

109

110

You can connect a computer to your balance to send commands via the balance interface port to control balance functions and applications. Format for commands

[ Command Code Data ]

•[: it shows start of command frame.

•Command Code: it shows which functionality to be carried out for this command frame.

•Data: This field in frame is optional and it is intended to provide data information between Bi-directional communications.

•]: it shows end of command frame.

Commands

[W] : If host computer send this command to balance then balance will Send weight with current unit.

[T] : If host computer send this command then balance will do taring in balance. If stability is not achieved within 45 second then it comes to that specific feature till that time it shows “-------“on LCM.

9.2 Data Input Format

ID code ID Code

characters Meaning Characters Meaning

nRef Counting: Reference sample quantity N1 Formulation, Net : N1

wRef Piece Counting, Percentage Weighing : N Formulation, Net N

Qnt Piece Counting: Quantity Tot Formulation,

pRef Weighing in percent: Reference percentage Pur density : Purity of Gold

Pct Weighing in percent: Reference percentage Den Density : density of sample

Cnt Animal weighing: No. of sub-weighing operations Pip Pipette Calibration

xNt Animal weighing: Calculated average Sta Statistics : to obtain the statistics of the data

Totalization

Reference weight

Totalization : Total Weight

• For connecting a computer or other peripheral device to the balance using the RS-232 protocol and cables up to 15m (50 ft.) long.

RS-232

3

TxD RxD

Gnd Gnd

RxD TxD

2

55

23

Balance

DB 9 Female Connector

Peripheral Device

e.g. Computer or Printer

Display

10. Error Codes

Cause

Overload

Under load

Weight set is to low for storing any reference at PCS, %, Custom Unit or Check Weighing.

While calibrating the scale, the load on the pan is more than 10% of the capacity. (During power on of the scale.)

Calibration

• User does not keep any weight on the pan within 60 second.

• Weight load on the pan is not within the tolerance limit.

GLP is ON and user tries to enter in to the User Menu before the footer is printed.

Calibration Display shows any weight other than 0.00 and user tries to Calibrate the balance

Incorrect value of TIME or DATE.

Solution

Remove excess weight from the weighing pan.

• Keep weighing Pan on Weighing Shaft. Check whether weighing pan is positioned properly.

Increase weight on the pan.

Switch OFF the Balance and Switch ON again without any load on the pan.

• Add the calibration weight on the pan when

demanded by the balance

• Calibrate with the exact Calibration Weight.

Print the footer first, by pressing <CANCEL> key, and then access the USER MENU.

Tare the balance or enter Calibration procedure when “0.00 g” is displayed.

Enter proper value of TIME or DATE.

111

112

9.3 Cabling Diagram

Display Cause

Last stored PRINT option is AUTO or AUTO LOAD or CONTINUOUS and user tries to set GLP ON from USER MENU.

RTC not operational.

Error 2 Calibration Error + RTC Error.

Error 3 Calibration Error + RTC Error.

Unstable ambient conditions A foreign object is caught between the load plate and the balance/scale frame

The balance has not been calibrated / adjusted. The balance was not zeroed before weighing.

Solution

Change the print option to Print on REQUEST and then turn GLP ON.

Contact Citizen Service center.

Set up the balance/scale in another area Remove the foreign object

Calibrate / Adjust the balance. Tare or Zero the balance before weighing.

The weight readout changes constantly

The weight readout is obviously wrong

Service

Regular servicing by a CITIZEN technician will extend the service life of your balance and ensure its continued weighing accuracy. CITIZEN can offer you service contracts, with your choice of regular maintenance intervals.

The optimum maintenance interval depends on the operating conditions at the place of installation and on the individual tolerance requirements.

Repairs

Repair work must be performed by trained service technicians. Any attempt by untrained persons to perform repairs may lead to hazards for the user.

Cleaning

• Unplug the DC adapter from the wall outlet (mains supply). If you have an interface cable connected to the balance/scale port, unplug it from the port.

• Make sure that no liquid enters the balance/scale housing

• Do not use any aggressive cleaning agents (solvents or similar agents)

• Clean the balance/scale using a piece of cloth which has been wet with a mild detergent (soap)

• After cleaning, wipe down the balance/scale with a soft, dry cloth

11. Care & Maintenance

113

114

Cleaning Stainless Steel Surfaces

• Clean all stainless steel parts regularly. Remove the stainless steel weighing pan and thoroughly clean it separately. Use a damp cloth or sponge to clean any stainless steel parts on the scale. You can use any commercially available household cleaning agent that is suitable for use on stainless steel. Clean stainless steel surfaces by wiping them down. Then clean the weighing pan thoroughly, making sure to remove all residues. Use a damp cloth or sponge to wipe down any stainless steel parts on the scale again. Afterwards, allow the scale to dry. If desired, you can apply oil to the cleaned surfaces as additional protection.

• Do not use stainless steel cleaning agents that contain soda lye (caustic), acetic acid, hydrochloric acid, sulfuric acid or citric acid. The use of scrubbing sponges made of steel wool is not permitted. Solvents are permitted for use only on stainless steel parts.

Safety Inspection

If there is any indication that safe operation of the balance/scale with the DC adapter is no longer warranted:

• Turn off the power and disconnect the equipment from DC power immediately

• Lock the equipment in a secure place to ensure that it cannot be used for the time being.

• Safe operation of the balance/scale with the DC adapter is no longer ensured when:

• There is visible damage to the DC adapter.

• The DC adapter no longer functions properly.

• The DC adapter has been stored for a relatively long period under unfavorable conditions.

115

116

117

LIMITED WARRANTY

ADDRESS :-

NAME :-

TEL NO. :-

MODEL NO. :-

WARRANTY PERIOD :-

SERIAL NO. :-

PURCHASE DATE :-

BRANCH / DISTRIBUTOR / CONTACT DETAILSDEALER

Owners Signature / Date

WARRANTY REGISTRATION

SEND YOUR WARRANTY CARD DULY FILL TO ABOVE ADDRESS FOR REGISTRATION

STAMP / SIGN

118

CITIZEN SCALES (I) PVT.LTD.

Citizen House, E2, Plot No. 11, WICEL Estate, Opp. Seepz Gate no. 1,

Andheri (E), Mumbai - 400 093. Maharashtra, India

e-mail :- service@citizenscales.com • web.: www.citizenscales.com

Tel. No. :- +91-22-4243 7700 • Fax :- +91-22-4243 7800

CITIZEN products are warranted against defects in materials and workmanship from the date of delivery through the duration of the warranty period.

During the warranty period Citizen will repair, or, at its option, replace any component (s) that proves to be defective at no charge, provided that

the product is returned, freight prepaid, to CITIZEN.

This warranty does not apply if the product has been damaged by accident or misuse, exposed to radioactive or corrosive materials, has foreign

material penetrating to the inside of the product, or as a result of service or modification by other than CITIZEN. In lieu of a properly returned warranty

registration card, the warranty period shall begin on the date of shipment to the authorized dealer. No other express or implied warranty is given by

Citizen Scale (i) Pvt. Ltd.

te and country to country, please contact citizen or your local CITIZEN dealer for further details.

ee of charge subject to terms & condition mentioned below.

5. Citizen Scale (I) Pvt. Ltd. shall not be liable for any consequential damages.

As warranty legislation differs from state to sta

CITIZEN service center will repair the product fr

TERMS & CONDITION

1. It covers only weighing balance purchased from authorized channel and does not cover accessories like Battery, Adaptor, RS232 cable, Pan, Pan support etc

2. It does not cover the product of which model and serial number has been altered, removed or defaced and / or is open by unauthorized person and found void sticker has been tampered.

3. This warranty is non-transferable and applicable only to first end user purchasing the product from authorized dealer.

4. For repair based on this warranty you need to hand over this product or send this product to address mentioned in warranty card in original packing, enclosing copy of this warranty card.‘

ISO 9001 : 2008 CERTIFIED

119

1)

212

171.5

204.5

342.5

231

67.5

190.5

189.5

152

97

165

255.5

271

78

169.5

29

Ø90

1)

212

171.5

204.5

342.5

231

67.5

97

325.5

239.5

165

78

341

Ø90

190.5

189.5

152

29

120

Analytical Balances

(CX / CY(0.1mg)Series Balances) Draft Shield High

Carat Balances

(CT Series Balances) Draft Shield Low

1)

212

171.5

204.5

342.5

231

67.5

96.5

78

128 X 128

169.5

29

255.5

190.5

152

271

189.5

165

212

342.5

231

89.5

67.5

210 X 198

171.5

208.5

48

1)

204.55

Precision Balances

(CY Series Balances) Draft Shield Low

Top Loading Precision Balances

(CG Series Balances) No Draft Shield

12. Dimensional Drawing

121

122

High Capacity Precision Balances

(SSH Series Balances)

High Capacity Precision Balances

(CY Series Balance with wind shield)

402

419.18

129.95

247

347

268.05

190.5

212

171.5

204.5

189.5

159

81

67.5

231

342.5

101

182

Model

Weighing Capacity Readability (d) Accuracy (e) Tare Range (Subtractive) Repeatability (std. deviation) Linearity Weighing Class Response time (average) Operating temperature range Calibration External calibration weight (of at least accuracy class...) Net Weight, approx. Pan size Weighing chamber height Dimensions (W x D x H) DC power source / Power requirements Frequency Power consumption (average) Selectable weight units

Built-in-interface Format Parity Transmission rates : Handshake mode

CX 301

301

0.1 1

-301

0.1

0.3

I

Internal 200 (E2)

CX 220

220

0.1 1

-220

0.1

0.2

I

18º to 30ºC

Internal

100 (E2)

CX 120

120

0.1 1

-120

0.1

0.2

I

18º to 30ºC

Internal

50 (E2)

CX 65

65

0.1 1

-65

0.1

0.2

I

18º to 30ºC

Internal

25 (E2)

CX 24

21

0.1 1

-21

0.1

0.2

II

15º to 30ºC

Internal

10 (E2)

3 sec. 18º to 30ºC

8kg 90 Ø

228.5

342.5 x 212 x 341 DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A 50 / 60Hz maximum 18; typical 9

RS-232 1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits Mark, Space, Odd, even, none 300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud None

gram, kilogram, pound, ounce, troy ounce, grain, pennyweight carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels Taiwan tales, baht

g mg mg g <=mg <=mg

s

0

C

0

C g kg mm mm mm V~ Hz VA

Analytical Balances

13. Specifications

123

124

Model

Weighing Capacity Readability (d) Accuracy (e) Tare Range (Subtractive) Repeatability (std. deviation) Linearity Weighing Class Response time (average) Operating temperature range Calibration External calibration weight (of at least accuracy class...) Net Weight, approx. Pan size Weighing chamber height Dimensions (W x D x H) DC power source / Power requirements Frequency Power consumption (average) Selectable weight units

Built-in-interface Format Parity Transmission rates : Handshake mode

CY 204

220

0.1 1

-220

0.1

0.2

I

18º to 30ºC

External 100 (E2)

CY 104

120

0.1 1

-120

0.1

0.2

I

18º to 30ºC

External

50 (E2)

CY 64

61

0.1 1

-61

0.1

0.2

I

18º to 30ºC

External

25 (E2)

CY 24

21

0.1 1

-21

0.1

0.2

II

15º to 30ºC

External

10 (E2)

CY 54

51

0.1 1

-51

0.1

0.2

II

15º to 30ºC

External

25 (E2)

3 sec.

8kg 90 Ø

228.5

342.5 x 212 x 341 DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A 50 / 60Hz maximum 18; typical 9

RS-232 1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits Mark, Space, Odd, even, none 300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud None

gram, kilogram, pound, ounce, troy ounce, grain, pennyweight carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels Taiwan tales, baht

g mg mg g <=mg <=mg

s

0

C

0

C

g kg mm mm mm V~ Hz VA

Analytical Balances

CX 54

51

0.1 1

-51

0.1

0.2

II

15º to 30ºC

Internal

25 (E2)

125

Model

Weighing Capacity Readability (d) Accuracy (e) Tare Range (Subtractive) Repeatability (std. deviation) Linearity Weighing Class Response time (average) Operating temperature range Calibration External cal. wt. (of at least accuracy class..) Net Weight, approx. Pan size Weighing chamber height with draftshield Weighing chamber height with Windshield Dimensions (W x D x H) with draftshield Dimensions (W x D x H) with windshield DC power source / Power requirements Frequency Power consumption (average) Selectable weight units

Built-in-interface Format Parity Transmission rates : Handshake mode

CY 120

120

0.001

0.01

-120

0.001

0.002

II

External

50 (F1)

CY 220

220

0.001

0.01

-220

0.001

0.002

II

15º to 30ºC

External 100 (F1)

CY 320

320

0.001

0.01

-320

0.001

0.002

II

15º to 30ºC

External 200 (F1)

CY 360C

360

0.001

0.01

-360

0.001

0.002

II

15º to 30ºC

Internal 200 (F1)

CY 360

360

0.001

0.01

-360

0.001

0.002

II

15º to 30ºC

External 200 (F1)

CY 720

720

0.001

0.01

-720

0.002

0.003

I

18º to 30ºC

External 500 (F1)

CY 510

510

0.001

0.01

-510

0.002

0.003

II

15º to 30ºC

External 300 (F1)

CY 420

420

0.001

0.01

-420

0.001

0.002

II

15º to 30ºC

External 200 (F1)

2 - 3 sec. 15º to 30ºC

7.5kg 128 x 128

158.5 81

342.5 x 212 x 271

342.5 x 212 x 193.5 DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A 50 / 60Hz maximum 18; typical 9

RS-232 1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits Mark, Space, Odd, even, none 300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud None

gram, kilogram, pound, ounce, troy ounce, grain, pennyweight carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels Taiwan tales, baht

g g g g <=g <=g

s

0

C

0

C g kg mm mm mm mm mm V~ Hz VA

Precision Balances

CY 1003

1000

0.001

0.01

-1000

0.002

0.003

I

18º to 30ºC

External 500 (F1)

126

Model

Weighing Capacity Readability (d) Accuracy (e) Tare Range (Subtractive) Repeatability (std. deviation) Linearity Weighing Class Response time (average) Operating temperature range Calibration External cal. wt. (of at least accuracy class..) Net Weight, approx. Pan size Weighing chamber height with draftshield Weighing chamber height with Windshield Dimensions (W x D x H) with draftshield Dimensions (W x D x H) with windshield DC power source / Power requirements Frequency Power consumption (average) Selectable weight units

Built-in-interface Format Parity Transmission rates : Handshake mode

CY 420C

420

0.001

0.01

-420

0.001

0.002

II

15º to 30ºC

Internal 200 (F1)

CY 510C

510

0.001

0.01

-510

0.002

0.003

II

15º to 30ºC

Internal 300 (F1)

CY 320C

320

0.001

0.01

-320

0.001

0.002

II

15º to 30ºC

Internal 200 (F1)

CY 220C

220

0.001

0.01

-220

0.001

0.002

II

15º to 30ºC

Internal 100 (F1)

CY 120C

120

0.001

0.01

-120

0.001

0.002

II

Internal

50 (F1)

CY 1003C

1000

0.001

0.01

-1000

0.002

0.003

I

18º to 30ºC

Internal

500 (F1)

2 - 3 sec. 15º to 30ºC

7.8kg 128 x 128

158.5 81

342.5 x 212 x 271

342.5 x 212 x 193.5 DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A 50 / 60Hz maximum 18; typical 9

RS-232 1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits Mark, Space, Odd, even, none 300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud None

gram, kilogram, pound, ounce, troy ounce, grain, pennyweight carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels Taiwan tales, baht

g g g g <=g <=g

s

0

C

0

C g kg mm mm mm mm mm V~ Hz VA

Precision Balances

Model

Weighing Capacity Readability (d) Accuracy (e) Tare Range (Subtractive) Repeatability (std. deviation) Linearity Weighing Class Response time (average) Operating temperature range Calibration External cal. wt. (of at least accuracy class..) Net Weight, approx. Pan size Dimensions (W x D x H) DC power source / Power requirements Frequency Power consumption (average) Selectable weight units

Built-in-interface Format Parity Transmission rates : Handshake mode

CG 1202

1200

0.01

0.1

-1200

0.01

0.02

II

15º to 30ºC

External

1000 (F1)

198 x 205

CG 613

610

0.01

-610

0.01

0.02

II

15º to 30ºC

External

300 (F1)

128 x 128

CG 612

610

0.01

0.1

-610

0.01

0.02

III

15º to 45ºC

External

300 (F1)

198 x 205

CG 312

310

0.01

0.1

-310

0.01

0.02

III

External 200 (F1)

2 - 3 sec. 15º to 45ºC

5.5kg 198 x 205

342.5 x 212 x 89.5 DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A 50 / 60Hz maximum 18; typical 9

RS-232 1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits Mark, Space, Odd, even, none 300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud None

gram, kilogram, pound, ounce, troy ounce, grain, pennyweight carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels Taiwan tales, baht

g g g g <=g <=g

s

0

C

g kg mm mm V~ Hz VA

Top Loading Precision Balances

127

Model

Weighing Capacity Readability (d) Accuracy (e) Tare Range (Subtractive) Repeatability (std. deviation) Linearity Weighing Class Response time (average) Operating temperature range Calibration External cal. wt. (of at least accuracy class..) Net Weight, approx. Pan size Dimensions (W x D x H) DC power source / Power requirements Frequency Power consumption (average) Selectable weight units

Built-in-interface Format Parity Transmission rates : Handshake mode

2 - 3 sec. 15º to 30ºC

5.5kg 198 x 205

342.5 x 212 x 89.5 DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A 50 / 60Hz maximum 18; typical 9

RS-232 1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits Mark, Space, Odd, even, none 300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud None

gram, kilogram, pound, ounce, troy ounce, grain, pennyweight carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels Taiwan tales, baht

g g g g <=g <=g

s

0

C

g kg mm mm V~ Hz VA

Top Loading Precision Balances

128

CG 2202

2200

0.01

0.1

-2200

0.01

0.02

II

External

1000 (F1)

CG 3102

3100

0.01

0.1

-3100

0.01

0.02

II

15º to 30ºC

External

1500 (F1)

198 x 205

CG 4102

4100

0.01

0.1

-4100

0.01

0.02

II

15º to 30ºC

External

2000 (F1)

198 x 205

CG 6102

6100

0.01

0.1

-6100

0.02

0.03

I

18º to 30ºC

External

4000 (F1)

198 x 205

CG 2102DR

200 / 2100

0.001 / 0.01

0.01 / 0.1

-200 / 2100

0.002 / 0.02

0.003 / 0.03

I

18º to 30ºC

External

1000 (F1)

128 x 128

342.5 x 212 x 271

Model

Weighing Capacity Readability (d) Accuracy (e) Tare Range (Subtractive) Repeatability (std. deviation) Linearity Weighing Class Response time (average) Operating temperature range Calibration External calibration weight (of at least accuracy class...) Net Weight, approx. Pan size Dimensions (W x D x H) DC power source / Power requirements Frequency Power consumption (average) Selectable weight units

Built-in-interface Format Parity Transmission rates : Handshake mode

SSH 96

10

0.01

0.1

-10

0.02

0.04

II

External

5 (E2)

SSH 95

15

0.1 1

-15

0.1

0.2

II

15º to 30ºC

External

10 (F1)

SSH 94

20

0.1 1

-20

0.1

0.2

II

15º to 30ºC

External

10 (F1)

SSH 94H

25

0.1 1

-25

0.1

0.2

II

15º to 30ºC

External

15 (F1)

2 - 3 sec. 15º to 30ºC

15kg 400 x 300 517 x 302 x 130 DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A 50 / 60Hz maximum 18; typical 9

RS-232 1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits Mark, Space, Odd, even, none 300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud None

gram, kilogram, pound, ounce, troy ounce, grain, pennyweight carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels Taiwan tales, baht

Kg g g Kg <=g <=g

s

0

C

Kg kg mm mm V~ Hz VA

High Capacity Precision Balances

130

CG 312C

310

0.01

0.1

-310

0.01

0.02

III

Internal

200 (F1)

CG 612C

610

0.01

0.1

-610

0.01

0.02

III

15º to 45ºC

Internal 300 (F1)

CG1202C

1200

0.01

0.1

-1200

0.01

0.02

II

15º to 30ºC

Internal

1000 (F1)

Model

Weighing Capacity Readability (d) Accuracy (e) Tare Range (Subtractive) Repeatability (std. deviation) Linearity Weighing Class Response time (average) Operating temperature range Calibration External cal. wt. (of at least accuracy class..) Net Weight, approx. Pan size Dimensions (W x D x H) DC power source / Power requirements Frequency Power consumption (average) Selectable weight units

Built-in-interface Format Parity Transmission rates : Handshake mode

CG 2202C

2200

0.01

0.1

-2200

0.01

0.02

II

15º to 30ºC

Internal

1000 (F1)

CG3102C

3100

0.01

0.1

-3100

0.01

0.02

II

15º to 30ºC

Internal

1500 (F1)

CG 4102C

4100

0.01

0.1

-4100

0.01

0.02

II

15º to 30ºC

Internal

2000 (F1)

CG 6102C

6100

0.01

0.1

-6100

0.02

0.03

I

18º to 30ºC

Internal

4000 (F1)

2 - 3 sec. 15º to 45ºC

6kg 198 x 205

342.5 x 212 x 89.5 DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A 50 / 60Hz maximum 18; typical 9

RS-232 1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits Mark, Space, Odd, even, none 300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud None

gram, kilogram, pound, ounce, troy ounce, grain, pennyweight carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels Taiwan tales, baht

g g g g <=g <=g

s

0

C

g kg mm mm V~ Hz VA

Top Loading Precision Balances

129

Model

Weighing Capacity Readability (d) Accuracy (e) Tare Range (Subtractive) Repeatability (std. deviation) Linearity Weighing Class Response time (average) Operating temperature range Calibration External calibration weight (of at least accuracy class...) Net Weight, approx. Pan size Weighing chamber height Dimensions (W x D x H) DC power source / Power requirements Frequency Power consumption (average) Selectable weight units

Built-in-interface Format Parity Transmission rates : Handshake mode

CT 103

101

0.001

0.01

-101

0.001

0.002

II

External

10 (F1)

CT 253

250

0.001

0.01

-250

0.001

0.002

II

15º to 30ºC

External

25 (F1)

CT 603

600

0.001

0.01

-600

0.001

0.002

I

18º to 30ºC

External

50 (F1)

CT 1603

1600

0.001

0.01

-1600

0.002

0.003

I

18º to 30ºC

External 200 (F1)

CT 1103

1100

0.001

0.01

-1100

0.001

0.002

I

18º to 30ºC

External

100 (F1)

3 sec. 15º to 30ºC

7.5 90 Ø

158.5

342.5 x 212 x 271 DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A 50 / 60Hz maximum 18; typical 9

RS-232 1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits Mark, Space, Odd, even, none 300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud None

gram, kilogram, pound, ounce, troy ounce, grain, pennyweight carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels Taiwan tales, baht

ct ct ct ct <=ct <=ct

s

0

C

kg mm mm mm V~ Hz VA

Carat Balances

132

131

Model

Weighing Capacity Readability (d) Accuracy (e) Tare Range (Subtractive) Repeatability (std. deviation) Linearity Weighing Class Response time (average) Operating temperature range Calibration External calibration weight (of at least accuracy class...) Net Weight, approx. Pan size Dimensions (W x D x H) DC power source / Power requirements Frequency Power consumption (average) Selectable weight units

Built-in-interface Format Parity Transmission rates : Handshake mode

SSH 93

35

0.1 1

-35

0.1

0.2

II

External

15 (F1)

SSH 92

50

1

10

-50 1 2

III

15º to 45ºC

External

25 (F1)

SSH 91

60

1

10

-60 1 2

III

15º to 45ºC

External

30 (F1)

SSH 90

100

1

10

-100 1 2

III

15º to 45ºC

External

50 (F1)

2 - 3 sec. 15º to 30ºC

15kg 400 x 300 517 x 302 x 130 DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A 50 / 60Hz maximum 18; typical 9

RS-232 1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits Mark, Space, Odd, even, none 300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud None

gram, kilogram, pound, ounce, troy ounce, grain, pennyweight carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels Taiwan tales, baht

Kg g g Kg <=g <=g

s

0

C

Kg kg mm mm V~ Hz VA

High Capacity Precision Balances

14. Accessories (Option)

Statistical Printer “CPR 02”

with Date / Time & Statistics

Remote Display “SRD01”

Calibration Weights

(F1) (ERTL, F2 with certificate) for further details, contact CITIZEN Dealers.

USB Interface

Density Kit “CDK 01”

For determination of solids for determination of liquids with displacement body

Antitheft device

Cable and lock (for all models)

Dust Cover

134

Model

Weighing Capacity Readability (d) Accuracy (e) Tare Range (Subtractive) Repeatability (std. deviation) Linearity Weighing Class Response time (average) Operating temperature range Calibration External calibration weight (of at least accuracy class...) Net Weight, approx. Pan size Weighing chamber height Dimensions (W x D x H) DC power source / Power requirements Frequency Power consumption (average) Selectable weight units

Built-in-interface Format Parity Transmission rates : Handshake mode

CT 103C

101

0.001

0.01

-101

0.001

0.002

II

Internal

10 (F1)

CT 253C

250

0.001

0.01

-250

0.001

0.002

II

15º to 30ºC

Internal

25 (F1)

CT 603C

600

0.001

0.01

-600

0.001

0.002

I

18º to 30ºC

Internal

50 (F1)

CT 1103C

1100

0.001

0.01

-1100

0.001

0.002

I

18º to 30ºC

Internal 100 (F1)

CT 1603C

1600

0.001

0.01

-1600

0.002

0.003

I

18º to 30ºC

Internal 200 (F1)

3 sec. 15º to 30ºC

7.8kg 90 Ø

158.5

342.5 x 212 x 271 DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A 50 / 60Hz maximum 18; typical 9

RS-232 1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits Mark, Space, Odd, even, none 300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud None

gram, kilogram, pound, ounce, troy ounce, grain, pennyweight carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels Taiwan tales, baht

ct ct ct ct <=ct <=ct

s

0

C

kg mm mm mm mm V~ Hz VA

Carat Balances

133

Citizen CY 104, CX 120, CY 64, CY 54, CX 65 Operating Manual

Specifications and Main Features

Frequently Asked Questions

User Manual