Citizen CW-01 User Manual

0 (0)

UUsseerr’’ss M

Maannuuaall

CW-01

Version 1.03

Concerning Copyright

●

The copyrights for this User’s Manual are the property of the CITIZEN SYSTEMS JAPAN CO.,LTD. Reproduction of any or all of the contents of this User’s Manual without consent of the company is a violation of copy-right law. However, for non-commercial, personal purposes, you may make one back-up copy.

Also, the contents of this User’s Manual are subject to change in the future without

prior notice.

●Concerning Safety Warnings

Warnings regarding safety and use, and the contents of the User’s Manual, conform to

standards existing as of the date published.

●Concerning modification

The CW-01

CO.,LTD. and for safety purposes, any modification of the device is prohibited.

printer was planned, developed, and manufactured by CITIZEN SYSTEMS JAPAN

CITIZEN SYSTEMS JAPAN CO.,LTD.

IInnttrroodduuccttiioon

Thank you very much for purchasing the CW-01 Dye Sublimation digital printer. This manual explains the handling and operation required to use this printer. Please read this manual well before starting operation and please use the printer correctly. Be sure to read “In order to use safely” (Pg 2-6), and use the printer safely.

FFoorr SSaaffee OOppeerraattiioon

・ Be sure to read this manual before use. After reading, keep it in a safe place, where it can be re-read as

needed.

・ The warnings listed here are to ensure proper use of the device, to prevent physical injury to the customer or

other persons, and to prevent property damage. Please obey these warnings.

■ About “Warning” and “Caution”

Listed below, the possible levels of injury or damage due to misuse are categorized as “Warning” and

“Caution”, according to the degrees of danger involved

WWaarrnniinngg

CCaauuttiioonn

■ About the symbols

The symbols shown have the following meanings:

・Accidents caused by failure to heed the warnings accompanying this symbol

could lead to serious or fatal injury.

・Accidents caused by failure to heed the warnings accompanying this symbol

could lead to physical injury or property damage.

This symbol calls attention to contents of warnings and cautions. Details are indicated in or near this s

This symbol indicates prohibited actions. The

This symbol designates necessary actions, and relevant content. Details of the actions are shown within the symbol.

rohibited actions are detailed within the symbol.

mbol.

CITIZEN SYSTEMS JAPAN CO.,LTD.

WWaarrnniinngg

Use only with the designated voltage and frequency. Improper connection could cause electric

・

shock or fire.

・

void overstressing outlets and using extension cords. The outlet could overheat and cause a fire. Do not damage, destroy, bundle, or alter the power cord. Also, placing heavy objects on, pull

・

ing, or bending the cord too much can damage it, and could cause a fire. Do not set the printer up in places with salinity or corrosive gases in the air. This could

・

cause a fire.

Do not block the cooling fan or vents. Heat could build up in the printer and cause a

・

malfunction or a fire.

Do not stand or place heavy objects on the printer. Also, do not use excessive force on the

・

buttons, switches, terminals, etc. This could break the printer and cause injury to the user o other people. Store the bag for the printer out of reach of children. It could cause suffocation if placed

・

over the head.

Do not open the printer cover while printing. This could break the printer.

・

Do not spill or spray liquids or chemicals into the printer.

・

When cleaning the cover, do not use thinner, trichoroethane, benzene, ketone-based cleaners,

・

or chemically treated cloths. They could discolor or deteriorate the cover. Be careful to avoid injury or damage from the edges in the printer.

・

Do not use this printer for applications where malfunction could be life-threatening

・

(such as medical, space, aeronautic, or other applications that require extreme reliability).

The printer weighs approximately 24 kg (52 lbs). When moving it, use two or more people,

・

and try to avoid strain when lifting it. Lifting recklessly or dropping the printer could cause

injury.

Locate the printer as close to an outlet as possible, and allow easy access to unplug the

・

power cord in case of problems.

If there is any dust on the plug, clean it off thoroughly. It could cause electric shock or a

・

short-out.

When disposing of the printer, peripheral items, packaging, or media, please abide by local

・

waste removal ordinances. For details, refer to your local government offices.

If metal objects or liquids have fallen into the printer, and there is smoke, a strange odor, or

・

any other apparent abnormality, immediately turn off the power, and unplug the power cord. Then contact a service representative. Do not continue using the printer if it is not operating properly. This could cause electric shock, short circuit, or fire. When unplugging the cord, grip the plug. Do not pull on the cord. It could damage

・

the cord, and cause electric shock or fire.

Be sure to attach the ground. Otherwise, it could cause a short circuit, electric shock, or fire.

・

Do not plug in or unplug the cord with wet hands. This could cause electric shock.

Do not open the inside of the printer, disassemble internal parts, or modify the printer.

・

It could cause electric shock, fire, or injury, or break the printer. For internal check-ups, adjustments, or repair, please contact a service representative.

CITIZEN SYSTEMS JAPAN CO.,LTD.

CCaauuttiioonn

Do not set the printer up in dusty or overly humid places. This could cause fire or electric

・

shock, or damage the printer.

Do not set the printer up on an unstable surface. It could fall and cause injury to the user

・

or other people.

Do not put foreign objects into the printer. They could cause electric shock, short circuit,

・

or fire, or break the printer. If something falls into the printer, immediately turn off the power, unplug the printer, and call a service representative.

At least once a year, unplug the power cord, and clean the prongs and the plug. If dust

・

accumulates, it could cause a fire. When printing continuously for long periods of time in a small room, be sure to ventilate

・

the room occasionally.

If use is intended on a transportation vehicle (train, truck, ship, etc.), please talk to a

・

representative in advance.

When moving the printer, be sure to unplug the power cord. Otherwise, the cord may be

・

damaged, which could cause fire or electric shock.

When not using the printer for extended periods of time, for the sake of safety, be sure to

・

unplug the power cord. It could cause electric shock or fire.

The thermal print head gets very hot. Do not touch the thermal print head right after printing.

・

It could cause burns.

If you want to dispose this product, do not mix with general household waste. There is a separate collection s used electronics products in accordance with le under the WEEE Directive (Directive 2002/96/EC) and is effective only within European Union.

WEEE MARK

CITIZEN SYSTEMS JAPAN CO.,LTD.

stem for

islation

WWaarrnniinnggss ffoorr SSeett--UUp

・Prior to operation, read “To use this printer safety” carefully and observe them.

・Use care when moving the printer. Never try carrying the printer alone.

Dropping it could cause injury or damage to other property.

・Do not use or store the printer near fire, excessive moisture, in direct sunlight, near an air

conditioner or heater, or any other source of unusually high or low temperature or humidity, or

excessive dust.

・Do not place the printer where chemical reactions occur, such as in a laboratory.

・Do not set up the printer where there is salinity or corrosive gas in the air.

・The printer must sit on a firm, level surface where there is ample ventilation. Never allow the

printer's air vent to be blocked by a wall or other object.

・Do not put anything on the top of the printer.

・Do not place the printer near a radio or television, and do not use the same wall outlet for the

printer and radio or television. Radio or television reception could be adversely affected.

・Do not use a power voltage or frequency other than those specified.

・Do not put anything on the power cord or step on it.

・Do not drag or carry the printer by the power cord or USB cable.

・Avoid plugging the power cord into an outlet with many loads.

・Do not bundle the power cord when inserting the plug.

・Always grip the plug housing, not the cord, to plug/unplug the power cord.

・Make certain the power is turned off before connecting/disconnecting the USB cable.

・Avoid lengthening the signal cable or connecting it to any noise-producing device.

If it is unavoidable, use a shielded cable or twisted pair for each signal.

・Place the printer near the outlet where the power cord can be unplugged easily to shut off power.

・Use an AC outlet that accepts a three-pronged plug. Otherwise, static electricity may be generated

and there will be danger of electric shock.

・Use the appropriate specified cord set.

Only use items that are certified safe according to the standards of the country where they are to be used

CITIZEN SYSTEMS JAPAN CO.,LTD.

●Japanese Users

Cord set No 5-AB0632-1 (60001080)

Parts number Rating Acquired Standard No

Plug KP-300 125V 12A JET-1807-43001-1004

Cord VCTF 1.25mm2 3G JET-2178-12009-1003

Connector KS-16A 125V 12A JET-1807-43004-1005

●American, Canadian Users

Cord set No INQ.1417 （60000980）

Parts number Rating Acquired Standard No

Plug CAT-009 125V 13A UL:E69228 CSA:LL93534

Cord SJT 1.25mm

Connector EF-28 125V 13A UL:E69228 CSA:LL93534

Cord set No 5-AB0638 (60001010)

Parts number Rating Acquired Standard No

Plug KP-30 125V 13A UL: E118569 CSA: LR84390

Cord SJT 1.25mm2 3G UL: E42955 CSA: LL84512

Connector KS-32 125V 13A UL: E118569 CSA: LL84391

●European Users

Cord set No 764S（60000960）

Parts number Rating Acquired Standard No

Plug 203 10/16A 250V EN60799

Cord H05VV-F 1.00mm23G EN60799

UL:E69167 CSA:LL97391 LL92902 LL42379

Connector EF-28 250V 10A EN60799

Cord set No 764S (60001030)

Parts number Rating Acquired Standard No

Plug KP-4819Y 10 / 16A 250V IEC60884

Cord H05VV-F(GTCE-3) 1.00mm23G IEC60227-5

Connector KS-31A 250V 10A IEC60320-1

CITIZEN SYSTEMS JAPAN CO.,LTD.

RReegguullaattoorryy ccoommpplliiaannccee ssttaatteemmeennttss

American users

FCC part 15

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

■ Reorient or relocate the receiving antenna

■ Increase the separation between the equipment and receiver

■ Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected

■ Consult the dealer or an experienced radio/TV technician for help

You are cautioned that changes or modifications not expressly approved by the party responsible

for compliance could void your authority to operate the equipment

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Caution: Use shielded cables to connect this computers.

Any changes or modifications not expressly approved by the grantee of this device could void the users authority to operate the equipment.

日本のお客様へ／Japanese Users

電波障害について

この装置は、情報処理装置等電波障害自主規制協議会（VCCI）の基準に基づくクラス B 情報技術装置です。この装置は､家庭環境で使用することを目的としていますが、この装置がラジオやテレビジョンの受信機に近接して使用されると、受信障害を引き起こす可能性があります。取扱説明書に従って正しい取り扱いをして下さい。

VCCI statement

This equipment is in the Class B category (information Technology Equipment to be used in a residential area or an adjacent area thereto) and conforms to standards set by the Voluntary Control Council for interference by information Technology Equipment aimed at preventing radio interference in such residential areas. When used near a radio or TV receiver, it may become the cause of radio interference. Read instructions for correct handling.

CITIZEN SYSTEMS JAPAN CO.,LTD.

DDeeccllaarraattiioonn ooff CCoonnffoorrmmiittyy

European users

The hereinafter mentioned product is manufactured according to Internal Production Control and Specific Apparatus Tests in compliance with

ANNEX Ⅲ of the R&TTE-Directive 99/05/EC

Product: CW-01 Photo Printer

The presumption of conformity with the essential requirements regarding Council Directive 99/05/EC is ensured according to

Art. 3.1 a) Safety: EN 60950: 2000 EN 50364: 2001

(equivalent to 73/23/EEC & 93/68/EEC)

Art. 3.1 b) EMC: ETSI EN 301 489-1 V1.4.1 (2002-08) ETSI EN 301 489-3 V1.4.1 (2002-08)

(equivalent to 89/336/EC)

Art. 3.2) Radio: EN 300 330-1 V1.3.2: (2002-12)

EN 300 330-2 V1.1.1: (2001-06)

The product bears the European Approvals Marking “CE”. Due to Class 1 categorized, alert mark to indicate using non-harmonized frequency and Notification to National Authorities according to Article 6.4 are not needed.

CITIZEN SYSTEMS JAPAN CO.,LTD.

English Hereby, Citizen Systems Japan Co.,Ltd. declares that this CW-01 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Finnish Citizen Systems Japan Co.,Ltd. vakuuttaa täten että CW-01 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Dutch Hierbij verklaart Citizen Systems Japan Co.,Ltd. dat het toestel CW-01 in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG Bij deze verklaart Citizen Systems Japan Co.,Ltd. dat deze CW-01 voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.

French Par la présente Citizen Systems Japan Co.,Ltd. déclare que ľappareil CW-01 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Par la présente, Citizen Systems Japan Co.,Ltd. déclare que ce CW-01 est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables.

Swedish Härmed intygar Citizen Systems Japan Co.,Ltd. att denna CW-01 står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

CITIZEN SYSTEMS JAPAN CO.,LTD.

+ 21 hidden pages