CatEye CC-ED400 User Manual

In use

CATEYE

ENDURO

CYCLOCOMPUTER

CC-ED400

Before using the computer, please thoroughly read this manual and keep it for future reference.

Warning / Caution

•Do not concentrate on the computer while riding. Ride safely!

•Install the magnet, sensor, and bracket securely. Check these periodically.

•If a child swallows a battery, consult a doctor immediately.

•Do not leave the computer in direct sunlight for a long period of time.

•Do not disassemble the computer.

•Do not drop the computer to avoid malfunction or damage.

•When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.

•Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to local regulations.

•LCD screen may be distorted when viewed through polarized sunglass lenses.

Maintenance

•To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and wipe it off with a dry cloth.

•If the gaps between the buttons and the unit get clogged with mud or sand, wash them away with water.

Replacing the battery

When the display becomes dim, replace the battery. Install a new lithium battery (CR2032) with the (+) side facing upward.

*After replacing the battery, be sure to set the unit again according to the procedure specified in “Preparing the computer” (page 3).

Close	COIN
Open	CR2032

Troubleshooting

No display.

Is battery in the computer run down?

Replace with new batteries according to the procedure specified in the section “Replacing the battery”.

Incorrect data appear.

Follow the procedure described “Preparing the computer” (page 3).

Current speed does not appear. (First, short-circuit the contact of the computer a few times with a piece of metal. If current speed appears, the computer is working fine and the cause should be attributed to the bracket or the sensor.)

Is the wire broken?

Even if the outside of the wire looks normal, there could be damage. Replace the bracket sensor kit with a new one.

Is the clearance between the sensor and the magnet too large? Are the magnet’s center and the sensor’s marking line aligned?

Re-adjust the positions of the magnet and the sensor. (The clearance should be less than 5 mm.)

Is there anything sticking on the contact of the computer or the bracket?

Clean the contact with a cloth.

ENDURO ENG 1

Specification

Battery / Battery life Lithium battery (CR2032) x 1 / Approx. 3 year

* The factory-loaded battery life might be shorter than the above-mentioned specification.

	Controller	4 bit, 1-chip microcomputer (Crystal controlled oscillator)
	Display	Liquid crystal display
	Sensor	No contact magnetic sensor
	Tire size to be	26”, 700c, 27”, 16”, 18”, 20”, 22” and 24”, or tire circumference of
	selected	100 cm - 299 cm (initial value: 26 inch)
	Working	32 °F - 104 °F (0 °C - 40 °C) (This product will not display appropri-
		ately when exceeding the Working Temperature range. Slow response
	temperature
		or black LCD at lower or higher temperature may happen respectively.)
	Dimensions/weight	2-3/16” x 1-15/32” x 5/32” (55.5 x 37.5 x 18.5 mm) / 1.06 oz (30 g)

* The specifications and design are subject to change without notice.

Limited warranty

2-Year: Computer only

(Accessories/Bracket sensor and Battery Consumption excluded)

CatEye cycle computers are warranted to be free of defects from materials and workmanship for a period of two years from original purchase. If the product fails to work during normal use, CatEye will repair or replace the defect at no charge. Service must be performed by CatEye or an authorized retailer. To return the product, pack it carefully and enclose the warranty certificate (proof of purchase) with instruction for repair. Please write or type your name and address clearly on the warranty certificate. Insurance, handling and transportation charges to CatEye shall be borne by person desiring service. For UK and REPUBLIC OF IRELAND consumers, please return to the place of purchase. This does not affect your statutory rights.

Please register your CatEye product on the website.

http://www.cateye.com/en/support/regist/

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn: CATEYE Customer Service Section

Phone	: [phone]	Fax	: [phone]
E-mail	: [e-mail]	URL	: http://www.cateye.com

[For US Customers]

CATEYE AMERICA, INC.

2825 Wilderness Place Suite 1200, Boulder CO80301-5494 USA

Phone	: 303.443.4595	Toll Free	: 800.5CATEYE
Fax	: 303.473.0006	E-mail	: [e-mail]

Spare accessories

Standard accessories

1603490	1603491	1699691N	1665150
			CR2032
Parts kit	Heavy duty bracket	Wheel	Lithium
	sensor kit	magnet	battery

Optional accessories

1603391

Bracket sensor kit

How to install the unit on your bicycle

Sensor

Double-sided tape

Magnet

Bracket

Wire

Spiral tube

1

2

Install the sensor and magnet

The magnet passes through the sensor zone.

Sensor

SENSOR ZONE

The clearance between the sensor and magnet is 5 mm or less.

Sensor

5 mm

				ENDURO ENG 2
	1Attach the bracket to the stem or handlebar			Remove/Install
	The FlexTight™ bracket can be attached to either the stem or the handlebar, depending on how the bracket fi ts into the			the computer
	bracket band.
	When attaching the FlexTight™ bracket to the stem		Stem
	Nylon ties	Bracket		Click
	Bracket		Cut
		Double-sided tape	Pull securely Nylon ties

	When attaching the FlexTight™ bracket to the handlebar	Bracket		While supporting it by hand,
	Nylon ties	Handlebar	Nylon ties
			Cut
	Bracket	Double-sided tape		Push it out as if lifting
			Pull securely	the front up

2Install the sensor and magnet

Spoke

Magnet

Sensor

To the

SENSOR ZONE

*The magnet may be installed anywhere on the spoke if the above installation conditions are satisfi ed.

	Cut
Sensor	Pull
	securely
	Nylon ties

3Route the wire

OK

Spiral tube

NO!

Nylon ties

Secure the cord on the fork with the nylon ties and lead to the handle bar along the outer cable of the bicycle by means of the spiral tube.

Caution:

Adjust the wire length so that it may not be pulled when the handle is operated.

(3/16”)