Casio AQ164W-1AV Operation Manual

MO0804-EA

Operation Guide 4380 4396 5048

About This Manual

Module 4380

Module 4396

Module 5048

•The operational procedures for Modules 4380 , 4396 and 5048 are identical. All of the illustrations in this manual show Module 4380.

•Button operations are indicated using the letters shown in the illustration.

•For the sake of simplicity, the sample displays in this manual do not show the analog hands of the watch.

•Depending on the model of your watch, display text appears either as dark figures on a light background, or light figures on a dark background. All sample displays in this manual are shown using dark figures on a light background.

•Each section of this manual provides you with the information you need to perform operations in each mode. Further details and technical information can be found in the “Reference” section.

General Guide

•Press C to change from mode to mode.

•In any mode (except when a setting screen is on the display), press B to illuminate

the face of the watch.

	Stopwatch Mode
Timekeeping Mode	Press C.
	▲
	Hand Setting Mode
	▲

▲

Timekeeping

Day of week

Month – Day

Minutes

Hours Seconds PM indicator

Use the Timekeeping Mode to set and view the current time and date. This watch features separate digital and analog timekeeping. The procedures for setting the digital time and analog time are different.

Setting the Digital Time and Date

Use the Timekeeping Mode to set and view a digital display of the current time and date. When setting the digital time, you also can configure settings for the summer time (Daylight Saving Time or DST).

To set the digital time and date

1. In the Timekeeping Mode, hold down A until the seconds start to flash, which indicates the setting screen.

2. Press C to move the flashing in the sequence shown below to select other settings.

Seconds	DST	Hour	Minutes
Seconds
Day	Month		Year

3.When the setting you want to change is flashing, use D and B to change it as described below.

Screen:	To do this:	Do this:
	Reset the seconds to 00	Press D.
	Toggle between Daylight Saving	Press D.
	Time (ON) and Standard Time (OF)
	Change the hour or minutes	Use D (+) and B (–).
	Change the year	Use D (+) and B (–).
	Change the month or day

4. Press A to exit the setting screen.

•The day of the week is displayed automatically in accordance with the date (year, month, and day) settings.

•Any time the seconds setting is changed, the analog hands are adjusted accordingly.

•See “Daylight Saving Time (DST) Setting” below for details about the DST setting.

To toggle between 12-hour and 24-hour timekeeping

In the Timekeeping Mode, press D to toggle between 12-hour timekeeping and 24hour timekeeping.

•With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for times in the range of noon to 11:59 p.m. and the A (AM) indicator appears to the left of the hour digits for times in the range of midnight to 11:59 a.m.

•With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without any indicator.

•The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is applied in all other modes.

•The A and P indicators are not displayed with the Timekeeping Mode time on the Countdown Timer Mode and Dual Time Mode screens.

Recall Mode	Countdown Timer
	Mode
▲	▲
Dual Time Mode	Alarm Mode
▲	▲

Daylight Saving Time (DST) Setting

Daylight Saving Time (summer time) advances the time setting by one hour from Standard Time. Remember that not all countries or even local areas use Daylight Saving Time.

To toggle the Timekeeping Mode digital time between DST and Standard Time

On/Off status

	ll ll				ll lll
	l		l	l			l
	l		l	l				l
	l		l	l			l
								l
	l		l	l
	l		l	l				l
	l	l	l	l				l
			l	l				l
							l
						l
On/Off status						l
DST indicator	DST indicator On/Off status			DST indicator
Module 4380	Module 4396			Module 5048

1.In the Timekeeping Mode, hold down A until the seconds start to flash, which indicates the setting screen.

2.Press C once and the DST setting screen appears.

3.Press D to toggle between Daylight Saving Time (ON displayed) and Standard Time (OF displayed).

4.Press A to exit the setting screen.

•The DST indicator appears on the Timekeeping, Alarm, and Hand Setting Mode screens to indicate that Daylight Saving Time is turned on.

Setting the Analog Time

Perform the procedure below when the time indicated by the analog hands does not match the time of the digital display.

To adjust the analog time

1. In the Timekeeping Mode, press C six times to enter the Hand Setting Mode.

2. Hold down A until the current digital time starts to

flash, which indicates the setting screen.

3. Use D to adjust the analog setting.

• Press D once to advance the hands 20 seconds.

• Hold down D to advance the hands at high speed.

• To lock high speed hands movement, hold down D to start it and then press B to lock. The hands will continue to advance for one 12-hour cycle or until you press any button to stop it.

• High-speed hand movement will stop automatically after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal, or countdown beeper) starts to sound.

4. Press A to exit the setting screen.

•The minute hand will be adjusted slightly to match the seconds when you exit the setting screen.

•To return to the Timekeeping Mode, press C.

Stopwatch

Remaining

free records

Hours			1/100 second

Minutes Seconds

The stopwatch lets you measure elapsed time, lap times, split times, and two finishes. Lap times and split times can be stored in memory.

•The display range of the stopwatch is 99 hours, 59 minutes, 59 seconds.

•All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C.

Note

•“Lap time” is the time spent to cover a specific segment of a race, such as one lap around a track. “Split time” is the time spent from the beginning of a race up to a certain point.

1

Lap time

Elapsed time

Split Time Recording

(Displayed for eight seconds after A is pressed.)

Split number

Split time

Elapsed time Lap time

Lap number

Operation Guide 4380 4396 5048

•The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it.

•The stopwatch measurement operation continues even if you exit the Stopwatch Mode.

•For information about how stopwatch times are stored in memory, see “Memory Management”.

Viewing the Stopwatch Digital Displays

The information that appears in the watch’s upper and lower digital displays depends on whether you are measuring lap times or split times.

Lap Time Measurement

Upper Display: Lap time

Lower Display: Elapsed time

Split Time Measurement

Upper Display: Lap time

Lower Display: Elapsed time (Split time appears here for eight seconds as it is stored in memory.)

•See “To measure elapsed time with lap times” and “To measure elapsed time with split times” for more information about each type of measurement.

•You can perform elapsed time measurement starting from either the lap time screen or the split time screen. Whenever you enter the Stopwatch Mode, the screen (lap time or split time) that was displayed when you last exited the mode will appear first.

•During a stopwatch elapsed time operation, the upper display initially shows minutes, seconds, and a 1/100-second value. This changes to hours, minutes, and seconds when the time in the upper display exceeds 60 minutes.

•The lower display initially shows hours, minutes, seconds, and a 1/100-second value. This changes to hours, minutes, and seconds when the time in the lower display exceeds 10 hours.

	Seconds		Minutes
	Minutes	1/100 second	Hours	Seconds
		More than one hour	▲
Minutes		1/100 second	Minutes
Hours	Seconds		Hours	Seconds
		More than 10 hours	▲

To measure elapsed time

Note

• You can perform the following steps starting from either the lap time screen or the split time screen.

1.Press D to start the stopwatch.

2.Press D again to stop the stopwatch.

• You can resume the measurement operation by pressing D.

3.Press A to clear the stopwatch to all zeros.

To measure elapsed time with lap times
1. When the stopwatch display shows all zeros, press
A to display the lap time screen (indicated by	/
LAP).

2. Press D to start an elapsed time measurement.

• At the time, both the upper and lower displays will show identical times.

3. Press A to record the time of the first lap.

Lap time

• This freezes the current lap time in the upper part of the digital display for about eight seconds, while measurement of total elapsed time and the next lap time continue internally. The lap number of the displayed time appears in the lower digital display.

•After eight seconds, the ongoing elapsed time measurement re-appears in the lower digital display.

4.Repeat step 3 to record more lap times.

5.Press D to stop the stopwatch.

6. Press A to clear the stopwatch to all zeros.

• Lap numbers are incremented automatically starting from 1 whenever you press A in step 3 of the above procedure. The maximum lap number is 99. Recording a lap after that causes the lap number count to restart from 00.

To measure elapsed time with split times

1. When the stopwatch display shows all zeros, press A to display the split time screen (indicated by /SPL).

2.Press D to start an elapsed time measurement.

•At the time, both the upper and lower displays will show identical times.

3.Press A to record the time of the first split.

•The current split time appears in the lower display for about eight seconds, as the total elapsed time, next

lap time, and next split time continue to be timed internally by the watch. The split number of the displayed time appears in the upper display.

• After eight seconds, the ongoing lap time measurement appears in the upper display and the ongoing elapsed time measurement appears in the lower display.

4.Repeat step 3 to record more split times.

5.Press D to stop the stopwatch.

6.Press A to clear the stopwatch to all zeros.

•Split numbers are incremented automatically starting from 1 whenever you press A in step 3 of the above

procedure. The maximum split number is 99. Recording a split time after that causes the split number count to restart from 00.

To time first and second place finishes

1.When the stopwatch display shows all zeros, press A to display the split time screen (indicated by /SPL).

2.Press D to start a time measurement.

3.Press A when the first finisher crosses the finish line.

•This freezes the time of the first finisher in the lower part of the digital display for about eight seconds. After that, the display returns to elapsed time measurement.

4.Press D when the second finisher crosses the finish line.

•The second finisher’s time will appear in the lower display.

•The difference between the first finisher’s and the second finisher’s time will appear in the upper display.

5.Press A to clear the stopwatch to all zeros.

Memory Management

A new log is created each time you press D in the Stopwatch Mode to start a new elapsed time measurement operation. A log contains a log title screen, and records of all the lap or split times you record during the current elapsed time measurement operation.

•The capacity of the watch’s memory is 60 records.

•If you are adding records to the only log in memory and watch memory becomes full, adding another record causes the oldest record in the log to be deleted automatically to make room for the new record.

•If you are adding records to a log when there are multiple logs in memory and watch memory becomes full, adding another record causes the oldest log in memory and all of its records to be deleted automatically to make room for new records.

How stopwatch data is stored

The following table shows how stopwatch data is stored when you perform stopwatch button operations.

Stopwatch Button	Data Storage Description
Operation
From all-zeros,	Creates a new log. Stores the date the button was pressed,
press D to start.	and the new log number.
Press A to	Creates a new record with each button operation. Stores the
display lap/split	lap and split times and total elapsed time at each point the
time.	button is pressed.
Press D to stop	Resets the elapsed time to all zeros without recording data.
elapsed time
measurrement and
then press Ato reset.

• See “Recall Mode” for details on how to recall time records from memory.

Recall Mode

Day of week Month – Day

Log number

Log Title Screen

Use the Recall Mode to recall and delete logs and records you stored in the Stopwatch Mode. You can use the Recall Mode to view both lap and split time records.

•When you enter the Recall Mode, the newest log recorded in the Stopwatch Mode will appear first. If there are no logs in memory, xxxx appears on the display.

•You can use the Recall Mode to check memory data even while a stopwatch elapsed time measurement operation is in progress. However, the time data that is currently being measured will not appear in the Recall Mode.

•You can convert a lap time saved in the Stopwatch Mode to a split time.

To recall stopwatch time records

1.In the Stopwatch Mode, check to make sure that the displays reset to all zeros.

•If all zeros are not displayed, reset the stopwatch.

2.Use the A button to select either the lap time screen (to view lap time records) or the split time screen (to view split time records).

•To convert a lap time saved in the Stopwatch Mode to a split time, select the split time screen.

3.Press the C button to enter the Recall Mode.

4.Use the A button to scroll through the log title screens from the newest to the oldest until the title screen of the log whose records you want to view is displayed.

5.Press D to scroll through the records contained in the log you selected in step 4, from the oldest to the newest.

First record

Last record

Lap time	Lap number
Log Title Screen
▲	▲
Press D.
▲	▲
▲
Log number

Split time

Split number

•Whether you will be able to view lap time records or split time records will depend on the screen you selected in step 2, above.

To delete a log

1.In the Recall Mode, display the title screen of the log you want to delete.

2.Hold down B and D until CLR stops flashing on the display.

•This deletes the log and all the records inside it.

•Deleting a single log slides all newer logs (ones with higher log numbers) upwards to fill the empty space. This cause the log numbers of all the newer logs to be reduced by 1. If there are six logs currently in memory (numbered 01 through 06) and you delete log 03, the numbers of logs that previously were numbered 04, 05, and 06 will change to 03, 04, and 05.

2