1584
SPEAKER CABLES
Use either 1/4” 16 gauge copper wire speaker cable or high-current Twist- Lok™
cables with heavy 4 conductor 12 gauge copper wire. The Carvin PH50 is
adequate for lengths up to 50’ under normal use. You can DAISY-CHAIN up to one
additional speaker per cable by using the OUTPUT connector. Be sure to note the
total impedance to the amp so it is not lower than it’s recommended impedance.
See Typical Loudspeaker Impedance Configurations.
SUGGESTIONS FOR OPTIMAL PERFORMANCE
Raise the enclosure to the ear level of your audience for greater coverage. To
help control feedback, keep the speakers in front of the microphone. Never direct
the microphone towards the speaker. Use a graphic EQ for further feedback
control. For greater coverage, add a second speaker system 20° to 30° off axis.
MODEL 1584 SPEAKER SYSTEM SPECS:
Frequency Response: 50 Hz to 19 kHz ±3 dB
Useable Low Frequency
Bandwidth: 38 Hz (-10 dB)
Power Handling: 400 watts Continuous Program Power
Recommended Amp: 75 to 600 watts
Sensitivity: 100 dB SPL, 1 Watt @ 1 meter
Coverage Angles: 90° Horizontal, 45° Vertical
Nominal Impedance: 8Ω
Crossover Type: C1584 Constant Voltage
Input & Output Connectors: Two 1/4", two Twist-Lok™
BIAMP Support: Yes—Panel Switch
Horn Driver Protection: Yes—Relay Dimming
Woofer Enclosure Type: Vented Box
Enclosure Covering: Black Duratuff™
Dim/Wt: 22"W x 15.25"D x 31.5"H, 68 lbs.
Warranty: One Year, Extended Warranty available
Optional Cables: PH50, SPK25, SPK50, SPK100
Optional Vinyl Cover: CVS1584
CARVIN ENGINEERING DATA 1584 SPEAKER SYSTEM INSTRUCTIONS
1584
SERIES CONNECTION
16Ω TOTAL IMPEDANCE
+
+
+
PARALLEL CONNECTION
4Ω TOTAL IMPEDANCE
+
+
+
8Ω TOTAL
IMPEDANCE
SERIES/PARALLEL
CONNECTION
8Ω TOTAL IMPEDANCE
+
+ +
+
+
+
+
8Ω
8Ω
8Ω
8Ω
8Ω
8Ω
8Ω
4Ω8Ω
8Ω
16Ω8Ω8Ω
REAR CONNECT PLATE
Two standard 1/4” phone jacks and two Twist Lok™ connectors are featured.
See hookup diagrams for full range and biamp options.
76-01584 0902
12340 World Trade Drive, San Diego, CA 92128
(619) 487-1600 (800) 854-2235
www.carvin.com
MIXER POWER AMP
SPEAKER SYSTEM
OUT
MODE SWITCH: FULL RANGE
ADDITIONAL
SYSTEM
SPK OUTINPUT
Toll Free 1-800-854-2235
USA
1
5841
PROFESSIONAL SOUND REINFORCEMENT
MADE IN THE
USA
8 Ω 400 Watts
JACKS WIRED
PARALLEL IN FULL
RANGE MODE
Speakon™
1+SIGNAL
1—GROUND
2+ & 2—
NOT USED
FULL RANGE—INPUT
BIAMP SW–HI FREQ. INPUT 8Ω
FULL RANGE —PARALLEL
BIAMP SW–LOW FREQ. INPUT 8Ω
BIAMP
FULL
RANGE
SPEAKER SYSTEM
MODE SWITCH: BIAMP
5841
PROFESSIONAL SOUND REINFORCEMENT
MADE IN THE
USA
8 Ω 400 Watts
JACKS WIRED
PARALLEL IN FULL
RANGE MODE
Speakon™
1+SIGNAL
1—GROUND
2+ & 2—
NOT USED
FULL RANGE—INPUT
BIAMP SW–HI FREQ. INPUT 8Ω
FULL RANGE —PARALLEL
BIAMP SW–LOW FREQ. INPUT 8Ω
BIAMP
FULL
RANGE
ELECTRONIC CROSSOVER
MIXER
OUT
IN (Set FREQ 600Hz) HILOSUB
MIXER POWER AMP
SPK OUTINPUT
USA
1
NORMAL FULL RANGE HOOKUP
BI-AMP HOOKUP
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________
1584 FREQUENCY RESPONSE
Congratulations on your selection of the 1584
loudspeaker. The 1584
vented, 400 watt 3-way speaker enclosure will exceed the performance
of the competition because of its superior design computer optimized
cabinet design, advanced C1584 crossover, and precisely aligned
speaker components. The 1584 is an outstanding system for a vast
array of applications ranging from clubs to outdoor use.
RECEIVING INSPECTION
INSPECT YOUR SPEAKER FOR ANY DAMAGE which may have occurred during
shipping. If any damage is found, please notify the shipping company & CARVIN.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your
unit, always use the original carton and packing material. CARVIN and the shipping
company are not liable for any damage caused by improper packing.
SA
VE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped
separately. Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER
on the enclosed warranty card or below on this manual
for your records. Return the warranty card with your name and comments to us.
WARRANTY
Parts and labor are covered for 1 year on manufacturer’s defects. Warranty does not
cover burned out drivers caused by excessive power or distortion, or physical damage
caused by general use, moisture or dust. CAUTION: Distortion from power amps can
destroy drivers much faster than clean power. Contact Carvin’s Customer Service at
800-854-2235 or returnsrepairs@carvin.com. Customer is responsible for shipping
charges.
TYPICAL LOUDSPEAKER IMPEDANCE CONFIGURATIONS
Individual speaker or speaker cabinet wiring examples for total impedance.
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________
c
See other side for SPS™ Powered Speaker operation
Loading...