RL410T
MODEL RL410T BASS SPEAKER SYSTEM SPECS:
Frequency Response: 60 Hz to 16k Hz
Drivers: Four 10” PS10 Woofers & one 1” Titanium HF Driver
Power Handling: 800 watts
Horn Attenuation: Switch attenuation (reduction) in 3dB steps
Horn Protection: Yes—Maintenance Free
Coverage Angles: 90° Horizontal, 90° Vertical
Nominal Impedance: 8Ω
Input Connector:
Speakon™ and One 1/4" Connector
Output Connector:
Speakon™ and One 1/4" Connector
Woofer Enclosure Type: Vented Box
Enclosure Covering: Duratuff II™
Dimensions: 23.5"W x 18.25"D x 25.5"H
Warranty: One Year
Weight: 69 lbs.
Optional Vinyl Cover: CVS115
Optional Casters: CTS4
CARVIN ENGINEERING DATA RL410T BASS SPEAKER SYSTEM INSTRUCTIONS
RL410T
The RL410T is a four-10” speaker system designed for the professional who wants
the absolute best in bass guitar amplification. With 4 heavy duty ten inch woofers
and an adjustable 1” Titanium HF Driver, your sound will be crisp and clear even at
the highest sound pressure levels. You will get clean, punchy, uncolored bass
reproduction from an all new cabinet & cross-over design. The new Duratuff II™
covered cabinet is 18 inches deep and is “front shelf” ported for a full, deep sound
that definitely does “Bloom” into any room! Caster inserts are already in place if
you choose to add the optional CTS4 casters.
RECEIVING INSPECTION
INSPECT YOUR SPEAKER FOR ANY DAMAGE which may have occurred during
shipping. If any damage is found, please notify the shipping company & CARVIN.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship
your unit, always use the original carton and packing material. This will provide the best
possible protection during shipment. CARVIN and the shipping company are not liable
for any damage caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped
separately. Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this
manual for your records. Keep your portion of the card and return the portion with your
name and comments to us.
TYPICAL LOUDSPEAKER IMPEDANCE CONFIGURATIONS
Individual speaker or speaker cabinet wiring examples for total impedance.
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________
SERIES CONNECTION
16Ω TOTAL IMPEDANCE
+
+
+
PARALLEL CONNECTION
4Ω TOTAL IMPEDANCE
+
+
+
8Ω TOTAL
IMPEDANCE
SERIES/PARALLEL
CONNECTION
8Ω TOTAL IMPEDANCE
+
+ +
+
+
+
+
8Ω
8Ω
8Ω
8Ω
8Ω
8Ω
8Ω
4Ω8Ω
8Ω
16Ω8Ω8Ω
76-00410B 0705
12340 World Trade Drive, San Diego, CA 92128
800.854.2235 www.carvin.com
REAR CONNECT PLATE
Two standard 1/4" phone jacks and two
high current Speakon
™
connectors are
featured. One for connecting to the
power amp and the other for connecting
to an additional speaker system.
Accepts Speakon™ & 1/4” cables
SPEAKER CABLES
12 gauge Speakon™speaker cables will provide a secure connection and high
current transfer of power to the speakers. You can also use standard 1/4" speaker
cables instead of the Speakon
™
cables provided they are at least 16 gauge. You
can DAISY-CHAIN up to one additional speaker per cable by using the unused
OUTPUT jack (right side) on your speaker jack plate. Be sure to note the total
impedance to the amp so it is not lower than it’s recommended impedance. See
Typical Loudspeaker Impedance Configurations.
PRECAUTIONS
1) DO NOT EXCEED THE POWER RATING marked on the rear connect plate.
Excessive power will destroy drivers. 2) DISTORTION from power amps will destroy
drivers much faster than clean power. 3) WATER, MOISTURE, and DUST are
harmful to drivers causing failure which is not covered under warranty.
WARRANTY
CARVIN loudspeakers are covered by a ONE year limited warranty unless
otherwise stated. Warranty coverage is limited to original manufactures defects
only. WARRANTY DOES NOT COVER: 1) Opened or burned voice coils. 2) Torn
cones caused by improper packing or abuse. 3) Damage from rain, moisture, ETC.
When returning defective driver(s), remove them from the enclosure to reduce
shipping costs. DO NOT stuff paper into the driver(s). Return pre-paid by UPS.
Include your address and description of the problem. Your driver(s) will be returned
COD for the cost of shipping and reconditioning if not covered under warranty.
HORN ATTENUATION SWITCHES
The rear crossover panel features a set of
attenuation switches to control the volume
of the 1” Titanium HF Driver. This will
allow you to turn the Driver full on or
reduce by 3dB increments to fine tune
your treble response.
Loading...