Carnes VUDK User Manual

SPECIFICATION SHEET

MODEL VUDK - DIRECT DRIVE

UPBLAST VENTILATORS

COPYRIGHT © 2007 CARNES COMPANY

ALL RIGHTS RESERVED

SUPERSEDES 22203-A 22203-B

A

DIA.

B

F

SQ.

C

SQ.

A

DIA.

B

F

SQ.

C

SQ.

UNIT SHOWN WITH
OPTIONAL ROOF
CURB AND BACK­DRAFT DAMPER
(8” (203) Min. Curb
Height Recommended)

CURB AND FLASHING SMALLER
THAN “C” [ALLOW 3/4” (19) EACH
SIDE FOR FLASHING]

NOTE: Drawing is to locate dimensions.

Refer to Catalog for actual model
configuration.

Models VUDK 06-08

Models VUDK 10-18

STANDARD FEATURES:

• Spun and shaped aluminum housing.

• Integral motor overload protection on all standard single phase motors.

• Disconnect switch on all motors except explosion proof.

• Ventilated motor compartment with motor out of the airstream.

• Non-overloading, backwardly inclined wheel.

• Isolated suspended motor wheel-drive assembly.

• Spark resistant construction.

• Integral drain opening.

STANDARD DIMENSIONS LISTED IN INCHES (Millimeters)

Unit Height Inside Roof Approx.

Unit B Curb Opening Curb Damper Wt. Less
Unit Diameter Standard Extended Cap Square O. D. Size Motor
Size A Height Height C F Square Square Lbs./Kg.

06 25-5/8 (651) 21-1/8 (537) 21-1/8 (537) 15-1/2 (394) 11 (279) 14 (356) 10 (254) 40 (18.1)
08 25-5/8 (651) 22-1/2 (572) 22-1/2 (572) 15-1/2 (394) 11 (279) 14 (356) 10 (254) 40 (18.1)
10 27-5/8 (702) 23-1/8 (587) 23-1/8 (587) 17-5/8 (448) 13 (330) 16 (406) 12 (305) 45 (20.4)
12 27-3/4 (705) 24-3/4 (629) 24-3/4 (629) 17-5/8 (448) 13 (330) 16 (406) 12 (305) 45 (20.4)
15 32-3/4 (832) 27-3/4 (705) 32-1/2 (826) 20-1/2 (521) 16 (406) 19 (483) 15 (381) 65 (29.5)
18 38-3/4 (984) 28-7/8 (733) 33-5/8 (854) 25 (635) 20-1/2 (521) 23-1/2 (597) 19 (483) 85 (38.6)

STANDARD MATERIAL AND THICKNESS

Motor Cover

Outer Curb Diffuser

Unit Lid Tube Shroud Cap Standard (Galvanized
Size Aluminum Aluminum Aluminum Aluminum Wheel Steel Gauge)

06 .063 (1.6) .040 (1.0) .080 (2.0) .050 (1.3) Aluminum 22 (.8)
08 .063 (1.6) .040 (1.0) .080 (2.0) .050 (1.3) Aluminum 22 (.8)
10 .063 (1.6) .040 (1.0) .080 (2.0) .063 (1.6) Aluminum 22 (.8)
12 .063 (1.6) .040 (1.0) .080 (2.0) .063 (1.6) Aluminum 22 (.8)
15 .063 (1.6) .040 (1.0) .080 (2.0) .063 (1.6) Aluminum 20 (.9)
18 .063 (1.6) .040 (1.0) .090 (2.3) .063 (1.6) Aluminum 18 (1.2)

Imperial [IP] Dimensions

Metric (SI) in Parentheses

CARNES COMPANY 448 S. Main St., P. O. Box 930040, Verona, WI 53593-0040 Phone: [phone] Fax: [phone] www.carnes.com