Canon PIXMA IP4600 Quick Start Guide
Photo Printer
iP4600
series
Getting Started
=Read Me First=
Make sure to read this manual before using the printer. Please keep it in hand for future reference.
Contents
Check the Box Contents
1
Sy mb ol s■
The following symbols are used to mark important instructions.
Observe these instructions.
Turn the Power On
2
Install the Print Head
3
Install the Ink Tanks
4
Install the Software
5
Loading Paper
6
After Installing the Printer
Instructions that, if ignored, could result in personal injury or
material damage.
Instructions that must be observed for safe operation.
Additional explanations.
Descriptions for operations that take some time to complete.
•
Microsoft is a registered trademark of Microsoft Corporation.
•
Windows is a trademark or registered trademark of Microsoft Corporation in the U.S.
and/or other countries.
•
Windows Vista is a trademark or registered trademark of Microsoft Corporation in the
U.S. and/or other countries.
•
Macintosh and Mac are trademarks of Apple Inc., registered in the U.S. and other
countries.
Model Number: K10323(iP4600)
1
Check the Box Contents
Manuals
•
Setup CD-ROM (containing the drivers, applications and on-screen manuals)
•
Warranty
•
MP-101 paper (for Automatic Print Head Alignment)
•
1
2 3 4 5
power cord Print Head ink tank
6
Before turning on the printer, remove all the protective sheets.•
A USB cable is necessary to connect the printer with your computer.•
1
2
Turn the Power On
1
2
3 4 5 6
1
(2)
(1)
Plug in the power cord on the left side at the
back of the printer and connect the other end
to the wall outlet.
2
Press the ON button (A) to turn on the printer. Confirm that the POWER lamp (B) lights
(A) (B)
3
green.
The printer may make some operating noises.
Do NOT connect the USB cable at this stage.•
2
•
This is normal operation.
3
Install the Print Head
1 2
3
4 5 6
•
Do not handle the Print Head
roughly such as applying them
excessive pressure or dropping
them.
1
(C)
(A)
Open the Paper Output Tray (A)
and the Top Cover (B).
The Print Head Holder (C) comes
out. (This is where you install the
Print Head .)
•
The Print Head Holder makes a
noise as it moves. This is normal
operation.
(B)
2
(D)
Raise the Print Head Lock Lever (D).
Firmly raise the Print Head Lock Lever until it stops. (The Print
•
Head Lock Lever may feel heavy.)
If the Print Head Holder does not move, make sure that the
•
printer is turned on.
3
3
Install the Print Head
1 2
3
4 5 6
4
Remove the Print Head from
the silver package.
•
There may be some transparent or light blue ink on the inside of the bag the Print
Head comes in, or the inside of the protective cap - this has no effect on print
quality. Be careful not to get ink on yourself when handling these items. Be careful
not to stain your hands.
Remove and discard the orange
protective cap.
53
(D)
Tilt the Print Head and set it in place. Lower the Print Head Lock Lever
(D) completely.
•
Do not knock the Print Head against the sides of the Holder.
•
Pinch the Print Head Lock Lever rmly and lower it gently.
•
Once you have installed the Print Head , do not remove them unnecessarily.
4
4
Install the Ink Tanks
4
5 61 2 3
•
Do not handle the ink tanks roughly such
as applying them excessive pressure or
dropping them.
•
If the Print Head Holder moves to the right,
close and reopen the Top Cover .
Be sure to use the supplied ink tanks .
•
1
(1)
(2)
Pull the orange tape (1) in the
direction of the arrow to peel off
the protective film and remove
the film (2) completely.
2
While pressing down with your left thumb, twist
off the orange protective cap (A) located on the
bottom of the ink tank .
Do not hold the sides of the ink tank ; ink may splash.•
(A)
5
4
Install the Ink Tanks
4
5 61 2 3
Ins t a ll t h e In k Tank
Press the PUSH mark on the ink tank until it
clicks into place.
Make sure the Ink lamp lights red.
Match the labels when installing.•
4
Install all the other ink tanks in the same way.
Install all the ink tanks . Wait until the POWER lamp lights green
Once you have installed the ink tanks , do not
•
remove them unnecessarily.
Make sure all the Ink lamp lights red.•
53
Close the Top Cover .
•
(about 6 minutes) and go to the next step.
The printer may make some operating
•
noises when preparing to print. This is
normal operation.
•
If an Alarm lamp (C) ashes orange, make
sure that the Print Head and the ink tanks are
correctly installed.
(C)
6
Install the Software
5
To use the printer by connecting it to a computer, software including
the drivers need to be copied (installed) to the computer's hard disk.
The screens below are based on Windows Vista operating system
Ultimate Edition (hereafter referred to as " Windows Vista ") and Mac
OS X v.10.5.x .
•
Quit all running applications before installation.
•
You need to log on as the administrator (or a member of the Administrators
group).
•
Do not switch users during the installation process.
•
It may be necessary to restart your computer during the installation process.
Follow the on-screen instructions and click OK , and do not remove the Setup
CD-ROM during restarting.
The installation resumes from where it left off when your computer has been
restarted.
•
Mac OS 9 , Mac OS X Classic environments, or Mac OS X v.10.3.8 or earlier
are not supported.
4
5
Windows (P.8)
Macintosh (P.16)
61 2 3
7
Windows
5
If the Found New Hardware or Found
New Hardware Wizard screen appears:
1
(B)
(A)
2
Press the ON button (A) to TURN OFF THE
PRINTER.
Remove the USB cable connected
1
to your computer.
The screen may close. In this case,
proceed from
Click Cancel to quit the screen.
2
Proceed from
3
8
.
.
•
Operating noise continues for about 30 seconds until
the printer turns off. Make sure that the POWER lamp
(B) stops ashing.
Turn on the computer, then insert the Setup
CD-ROM into the CD-ROM drive.
The setup program should run automatically.
Windows Vista
Windows XP/2000
•
If the program does not start automatically, doubleclick the CD-ROM icon on the computer. When the
CD-ROM contents appear, double-click MSETUP4.
EXE.
Go to Step
Go to Step
.
.
Loading...