Canon MP450 User Manual

Thank you for purchasing the Canon PIXMA MP450. To prepare your machine for use, please follow these Easy Setup Instructions before referring to any other documentation.

IMPORTANT

Do not connect the USB cable until after the software is installed. See the reverse side of this sheet for details.

2 Prepare the FINE Cartridges.

1 Unpack the machine.

1 Carefully remove all items from the box. 2 Check the package contents.

• See the flapped lid of the packing box.

3 Place the machine on a flat surface. 4 Remove all shipping tape and the protective sheet. 5 Open the Scanning Unit and remove the protective material (A).

(A)

• Be sure to hold the machine by the side. Do not lift the machine by grasping the Paper Support Extension or the Operation Panel.

2 Connect the power cord.

Remove the protective tape.

Do not touch!

3 Insert the FINE Cartridges.

4 Close the Scanning Unit.

• Lift the Scanning Unit to put the Scanning Unit Support back to its original position.

IMPORTANT

Wait until the preparatory operation is complete; this takes about one to two minutes.

1 Connect the power cord. 2 Press [ON/OFF] to turn

ON the machine.

3 Use [ ] or [ ] on the Operation Panel to select the language on the LCD,

then press [OK].

• The language setting is only available for some countries.

3 Install the FINE Cartridge.

1 Lift the Scanning Unit and pull the Scanning Unit Support down into place.

4 Load the paper.

1 Open the Paper Support (1) and pull up the Paper Support Extension (2) until

it stops.

2 Load the paper with the print side face up.

• Ensure the paper stack does not exceed the Load Limit Mark (A).

3 Pinch and adjust the Paper Guide (3) to the width of the stack. 4 Open the Paper Output Tray.

(1)

(3)

(A)

(2)

IMPORTANT (US only)

• Write down the serial number. You will need this to register the product.

The cartridge moves to the left.

Install the FINE Cartridges here.

The hardware setup is complete.

If you are connecting the machine to a computer for use, see the reverse side for instructions on installing the software.

QT7-0008-V02 xx2005A © CANON INC. 2005 PRINTED IN VIETNAM

Install the software.

Select Easy Install in order to install the application software, On-screen Manual and MP drivers. Select Custom Install in order to choose the options you would like to install. This sheet explains Easy Install only.

IMPORTANT

• Close any open software applications, including virus checkers, prior to installing the software.

The following software programs are included on the Setup CD-ROM:

On-screen Manual MP Drivers MP Navigator

Easy-PhotoPrint Easy-WebPrint ScanSoft OmniPage SE

ArcSoft PhotoStudio

IMPORTANT

• Do not connect the USB cable until Step 4, “Connect the USB cable.”

• Before installing the software in Windows XP or Windows 2000, you must log on as Administrator or a user with Administrator privileges.

• If you have an earlier version of the MultiPASS Suite software installed on your computer, uninstall this version before installing the new version. For instructions on uninstallation, see the guides for that version of the MultiPASS Suite.

Step 1: Prepare the Setup CD-ROM and get ready to install.

1 Turn OFF the machine. 2 Turn ON your computer, and start Windows. 3 Insert the Setup CD-ROM into the CD-ROM drive.

• The setup program should automatically run. If the setup program does not automatically run, click [My Computer], then double-click the CD-ROM icon.

IMPORTANT

If the following screen appears, the USB cable is connected.

z Perform the following steps.

1. Turn OFF the machine.

2. Disconnect the USB cable.

3. Click [Cancel].

Click

The following software programs are included on the Setup CD-ROM:

On-screen Manual MP Drivers MP Navigator

Easy-PhotoPrint ScanSoft OmniPage SE ArcSoft PhotoStudio

IMPORTANT

• Do not connect the machine to Mac OS 9 or Mac OS X Classic environments since they are not supported.

Step 1: Turn ON the machine, and connect the USB cable.

Step 2: Prepare the Setup CD-ROM.

1 Turn ON your computer, and start Mac OS X. 2 Insert the Setup CD-ROM into the CD-ROM drive. 3 Double-click [Setup] on the Setup CD-ROM, or click [Setup] on the Setup CD-

ROM and click [File] menu and then select [Open].

Step 3: Enter the name and password for an Administrator

Account.

1 Enter the name for the Administrator. 2 Enter the password and then click [OK].

Enter Click

Step 4: Select the language and place of residence.

• In some countries, the [Select Language] and [Select Your Place of Residence] dialog boxes will not be displayed. Go to Step 5.

1 Select the language to use with this

CD-ROM and then click [Next].

2 Select your place of residence and

then click [Next].

Step 2: Select the language and place of residence.

• In some countries, the [Select Language] and [Select Your Place of Residence] dialog boxes will not be

displayed. Go to Step 3.

1 Select the language to use with this

CD-ROM and then click [Next].

Click

2 Select your place of residence and

then click [Next].

Step 3: Install the software.

1 Click [Easy Install], then click [Install].

• To read descriptions of the software programs, set the mouse on the item.

Click

Step 5: Install the software.

1 Click [Easy Install], then click [Install].

• To read descriptions of the software programs, set the mouse on the item.

Click

2 Click [Yes].

• Installation begins. Follow the displayed instructions.

3 Click [Restart] to restart your

Click

computer.

Click

2 Read the License Agreement, then click [Yes].

• Installation begins. Follow the displayed instructions.

Step 4: Connect the USB cable.

1 When the [Printer Connection] appears, connect the machine to the computer

with the USB cable.

2 Turn ON the machine.

In Windows 2000, the machine may not be set as the default printer.

3 Click [Exit].

• If prompted to, restart your computer.

Click

US only

• When the Registration window appears, follow the on-screen instructions to ensure product support. The serial number is located inside the machine. (See “3 Install the FINE Cartridge.” on the reverse side of this sheet)

Click

US only

* When connecting from Mac OS X v.10.3.3 or earlier:

Restarting the computer while connected to the machine may cause the machine not to be detected. To resolve this, either unplug the USB cable then plug it back in again, or turn the machine OFF then back ON again.

z Perform the following to make sure the driver has been installed correctly.

1. Select [Applications] from the [Go] menu.

2. Double-click the [Utilities] folder, then double-click the [Printer Setup Utility] ([Print Center] when using Mac OS X v.10.2.x) icon. If the printer is displayed in the [Printer List], the printer driver is installed. If the printer is not displayed in the [Printer List], click [Add] in the [Printer List] and select [USB] from the pop-up menu. Select your machine from the [Product] list and click [Add].

You now have completed installation of the software.