Burkert 8750 User Manual
Type 8750
Classic with Type 8693
Flow controller
Quickstart
English
We reserve the right to make technical changes without notice.
Technische Änderungen vorbehalten.
Sous réserve de modifications techniques.
© 2012 Bürkert Werke GmbH
Operating Instructions 1210/00_EU-EN_00810234 / Original DE
Typ 8750
Inhaltsverzeichnis
1. QUICKSTART GUIDE.....................................................................................5
1.1. Definition of terms / Abbreviation ................................................. 5
2. SYMBOLS ............................................................................................................5
3. AUTHORIZED USE .........................................................................................6
3.1. Restrictions ........................................................................................6
4. BASIC SAFETY INSTRUCTIONS .............................................................6
5. GENERAL INFORMATION ...........................................................................7
5.1. Contact address ............................................................................... 7
5.2. Warranty ............................................................................................. 7
5.3. Information on the Internet ............................................................. 7
6. SYSTEM DESCRIPTION ...............................................................................8
6.1. General description ......................................................................... 8
6.2. Structure ............................................................................................8
7. TECHNICAL DATA ........................................................................................10
7.1. Conformity .......................................................................................10
7.2. Standards .........................................................................................10
7.3. Operating conditions .....................................................................10
7.4. Mechanical data .............................................................................10
7.5. Type label .........................................................................................11
7.6. Fluidic data ......................................................................................11
7.7. Electrical data..................................................................................12
8. CONTROL AND DISPLAY ELEMENTS ................................................... 14
8.1. Function of the keys ........................................................................ 14
8.2. Operating state ................................................................................ 15
8.3. Operating levels ............................................................................... 16
8.4. Display in AUTOMATIC operating state ...................................16
8.5. Master code.....................................................................................17
9. ASSEMBLY .......................................................................................................18
9.1. Safety instructions .........................................................................18
9.2. Before installation ...........................................................................18
9.3. Pneumatic connection of the process controller ....................18
10. ELECTRICAL INSTALLATION ............................................................... 20
10.1. Electrical installation, 24 V DC with circular plug-in
connector (multi-pole variant) ...................................................... 20
10.2. Electrical installation PROFIBUS DP ......................................22
10.3. Electrical installation DeviceNet ...............................................23
11. START-UP 24 V DC ...................................................................................25
11.1. General procedure for creating settings for the flow
controller ........................................................................................25
11.2. Define basic settings ...................................................................26
11.3. Automatic adjustment (X.TUNE) ............................................... 27
11.4. Configuring the F.CONTROL auxiliary function ....................... 28
12. ADDITIONAL FMR FUNCTIONS ......................................................... 30
12.1. Activating and deactivating auxiliary functions ......................32
12.2. CAL.USER - Changing the factory calibration ....................32
12.3. OUTPUT - Configuration of the analog output ....................34
english
3
13. PROFIBUS DP START-UP ..................................................................... 35
13.1. Settings in BUS.COMM ....................................................... 35
13.2. Configuration of the process values ........................................36
14. DEVICENET START-UP ........................................................................... 39
14.1. Settings in BUS.COMM ....................................................... 39
14.2. Configuration of the process data ...........................................41
15. SAFETY END POSITIONS ..................................................................... 46
16. ERROR MESSAGES .................................................................................46
16.1. Error messages on field bus devices ......................................48
16.2. Other error messages .................................................................49
17. ACCESSORIES ...........................................................................................50
18. SHUTDOWN .................................................................................................. 50
18.1. Disassembly ..................................................................................50
19. OPERATING STRUCTURE ..................................................................... 51
20. TRANSPORT, STORAGE, PACKAGING .......................................... 62
Typ 8750
4
english
Typ 8750
Quickstart Guide
1. QUICKSTART GUIDE
The quickstart guide describes the entire life cycle of the device. Keep
these instructions in a location which is easily accessible to every user
and make these instructions available to every new owner of the device.
Important Safety Information.
Read Quickstart carefully and thoroughly. Study in particular the
chapters entitled Basic Safety Instructions and Authorized Use.
▶ Quickstart must be read and understood.
The Quickstart guide illustrates the installation and commissioning of
the equipment with examples.
A detailed description of the process controller can be found in the
operating instructions for Type 8693.
The operating instructions can be found on the Internet at:
www.burkert.com
1.1. Definition of terms / Abbreviation
In these instructions, the term “device” always refers to the flow
controller Type 8750.
FMR = Flow controller
2. SYMBOLS
The following symbols are used in these instructions.
DANGER!
Warns of an immediate danger.
▶ Failure to observe the warning will result in a fatal or serious injury.
WARNING!
Warns of a potentially dangerous situation.
▶ Failure to observe the warning may result in a serious or fatal injury.
CAUTION!
Warns of a possible danger.
▶ Failure to observe this warning may result in a moderate or minor
injury.
NOTE!
Warns of damage to property.
Important tips and recommendations.
Refers to information in these operating instructions or in
other documentation.
▶ Indicates an instruction to prevent risks.
→ designates a procedure which you must carry out.
english
5
Typ 8750
Authorized use
3. AUTHORIZED USE
Non-authorized use of the flow controller Type 8750 may be a
hazard to people, nearby equipment and the environment.
• The device is designed as a simple system for determining and
controlling the volumetric flow rate of gases.
• Do not expose the device to direct sunlight.
• Do not use the device outdoors.
• Use according to the authorized data, operating conditions, and
conditions of use specified in the contract documents and operating instructions. These are described in Chapter “7. Technical
data”.
• Use the device only in conjunction with third-party devices and
components recommended and authorized by Bürkert.
• Correct transportation, storage, and installation, as well as careful use and maintenance are essential for reliable and faultless
operation.
• Use the device only as intended.
3.1. Restrictions
If exporting the system/device, observe any existing restrictions.
4. BASIC SAFETY INSTRUCTIONS
These safety instructions do not make allowance for any
• Contingencies and events which may arise during the installation,
operation, and maintenance of the devices.
• Local safety regulations – the operator is responsible for observing
these regulations, also in relation to the installation personnel.
Risk of injury from high pressure in the equipment/device.
▶ Before working on equipment or device, switch off the pressure
and deaerate/drain lines.
Risk of electric shock.
▶ Before reaching into the device, switch off the power supply and
secure to prevent reactivation.
▶ Observe applicable accident prevention and safety regulations
for electrical equipment.
Risk of burns/risk of fire if used during long-term operation
through hot device surface.
▶ Keep the device away from highly flammable substances and media
and do not touch with bare hands.
General hazardous situations.
▶ Devices without a separate Ex type label may not be used in a
potentially explosive area.
▶ Only trained technicians may perform installation and maintenance
work.
6
english
Typ 8750
General information
▶ That the system cannot be activated unintentionally.
▶ After an interruption in the power supply or pneumatic supply,
ensure that the process is restarted in a defined or controlled
manner.
▶ The device may be operated only when in perfect condition and
in consideration of the operating instructions.
▶ The general rules of technology apply to application planning and
operation of the device.
▶ Do not supply the pilot air port with aggressive or flammable media.
▶ Do not supply the pilot air port with liquids.
▶ Do not physically stress the body (e.g. by placing objects on it or
standing on it).
▶ Do not make any internal or external changes on the device.
NOTE!
Electrostatic sensitive components/modules.
The device contains electronic components which react sensitively
to electrostatic discharge (ESD). Contact with electrostatically
charged persons or objects are hazardous to these components.
In the worst case scenario, they will be destroyed immediately or
will fail after start-up.
▶ Observe the requirements specified in EN 61340-5-1 to minimize/
avoid the possibility of damage caused by a sudden electrostatic
discharge.
▶ Do not touch electronic components while the supply voltage is
switched on.
5. GENERAL INFORMATION
5.1. Contact address
Germany
Bürkert Fluid Control Systems
Sales Center
Christian-Bürkert-Str. 13-17
D-74653 Ingelfingen
Tel. + 49 (0) 7940 - 10 91 111
Fax + 49 (0) 7940 - 10 91 448
E-mail: info@de.buerkert.com
International
Contact addresses can be found on the final pages of the printed
operating instructions.
And also on the Internet at:
www.burkert.com
5.2. Warranty
The warranty is only valid if the flow controller Type 8750 is used as
intended in accordance with the specified application conditions.
5.3. Information on the Internet
The operating instructions and data sheets for Type 8750 / Type 8693
can be found on the Internet at:
www.burkert.com
english
7
Typ 8750
System description
6. SYSTEM DESCRIPTION
6.1. General description
To determine and control the volumetric flow rate, the pressure drop
over the control valve is measured continuously by the two pressure
sensors. This pressure difference and the valve flow characteristic
are the parameters used to determine the volumetric flow. This measured volumetric flow is compared with the set point – internally via
display/keyboard or externally via standard signal or bus protocol –
evaluated in a PID controller and set on the position controller as the
new set point.
The system consists of:
• Control valve Type 2712 with process controller Type 8693
• Two pressure sensors Type 8323
Options:
• Binary input
• Analog feedback
• 2 binary outputs
• Bus communication (PROFIBUS DP or DeviceNet)
Other:
• The flow controller is supplied with a factory setting.
• The device is operated via 4 function keys and a display.
• The valve seat can be exchanged.
6.2. Structure
Process controller Type 8693
Actuator control valve Type 2712
Signal line from pressure sensor to
the process controller
Valve body control valve
Type 2712
Pressure sensor Type 8323
Fig. 1: Structure
6.2.1. Action diagram of the FMR
Pressure P1 Pressure P2
Temperature T
(Option)
P1 P2
Fig. 2: Action diagram
Kv value
PV
Flow
controller
(FMR)
Type
8750
Flange acc. to
DIN EN 1092-1
8
english
Typ 8750
System description
6.2.2. Electrical interfaces
Inputs for position
or process setpoint value
0 – 20 mA
4 – 20 mA
0 – 5 V
0 – 10 V
Inputs for process
actual value
(4 – 20 mA)
P1
P2
T (optional)
Binary input
24 V DC
Fig. 3: Interfaces
Inputs
Power
supply
Process controller
Type 8693
Operation
(keys)
2 binary outputs
(option)
Analog
position
feedback
(option)
Outputs
Bus
Inputs for process
actual value
(4 – 20 mA)
P1
P2
T (optional)
24 V DC
Fig. 4: Interfaces - Bus
Process controller Type
Inputs
8693
PROFIBUS DP
DeviceNet
Power
supply
Operation
Bus
Outputs
english
9
Typ 8750
Technical data
7. TECHNICAL DATA
7.1. Conformity
Type 8750 conforms to the EC directives according to the EC Declaration of Conformity.
7.2. Standards
The applied standards which are used to demonstrate compliance with
the EC Directives are listed in the EC type test certificate and/or the
EC Declaration of Conformity.
7.3. Operating conditions
Ambient temperature 0 – +55 °C
Degree of protection
IP65 / IP67 according to EN 60529 (only if cables, plugs and
sockets have been connected correctly and in compliance with
the exhaust air concept in Chapter “9.3. Pneumatic connection
of the process controller”)
7.4. Mechanical data
Materials
Valve body stainless steel cast 1.4404/316L
Sensor connection 1.4301 or 1.4404
Flange stainless steel 316L
Actuator Polyamide (PA)
Process controller PPS, PC, stainless steel
seals EPDM
Packing gland PTFE rings with silicone grease
Other wetted parts stainless steel 1.4571
Inlet and outlet sections acc. to EN ISO 5167-1
Inlet sections
Valve completely open
20 x D
90° bend or T-piece
20 x D
Widening
18 x D
Reduction
15 x D
Fig. 5: Inlet sections
Outlet sections already integrated in the system (6 x DN)
10
english
Typ 8750
Technical data
Dimensions
∅ 91
∅ E
HG
2x DN
L
Fig. 6: Dimensions
6x DN
DN pipe connection [mm] L [mm] HG [mm] ∅ E [mm]
15 330 414 101
25 500 412 101
40 700 501 127
50 800 538 157
65 1000 567 157
80 1200 637 261
100 1400 647 261
Tab. 1: Dimensions
7.5. Type label
Example:
Operating voltage /
Fig. 7: Example of type label
control
Type
8750 24 V DC
single act Pilot 0,6
Pmax 7 bar
Tamb 0°C - +55°C
S/N 001000
00179026
D-74653 Ingelfingen
CE
W14UN
Identification number
Control function
Pilot valve
Maximum pressure
Max. ambient
temperature
Serial number,
CE symbol
Bar code
7.6. Fluidic data
Control medium neutral gases, air
Quality classes as per DIN ISO 8573-1
Dust content Class 5: max. particle size 40 μm,
max. particle density 10 mg/m
Water content Class 3: max. pressure dew point -20 °C or
min. 10 °C below the lowest operating
temperature
Oil content Class 5: max. 25 mg/m
3
3
english
11
Typ 8750
Technical data
Temperature range
control medium 0 – +50 °C
Pressure range
control medium 5.5 – 7 bar (DN 15 – DN 65)
5 – 6 bar (DN 80 – DN 100)
Intrinsic air consumption 0 l/min
Connections plug-in hose connector 6 mm / 1/4”
threaded connection G 1/8
Flow media air and gases
steam on request
Temperature range
Media 0 – +80 °C
Pressure range
Media 0 – 16 bar
Connections flange acc. to DIN EN 1092-1, ANSI,
JIS
Pressure measurement
range of sensor 0 – 6/10 or 16 bar
depending on the pressure range of
media others available on request
Measurement section acc. to DIN EN 60534-2-3
Orifices DN 15 - DN 100
Sensor connections threaded connection G 1/2
7.7. Electrical data
Connections
Operating voltage circular plug-in connector M12 x 1, 4-pole
External signals circular plug-in connector M12 x 1, 8-pole
circular plug-in connector M8 x 1, 8-pole
Operating voltage 24 V DC
- maximum residual ripple 10 %
Power consumption < 5 W
Set-point value default 0/4 – 20 mA or
0 – 5/10 V
field bus as option
Display multifunction display
User interface 4 function keys
12
english
Typ 8750
Technical data
Kv value table for FMR versions (specifications for valve stroke and flow rate in %)
The measured set of values for each seat combination is stored in the FMR memory at the factory.
Flow rate Kv in [%]
Valve design
DN
DN
pipe
seat
[mm]
[mm]
8 2,1 0,0 3,3 3,8 4,8 5,2 5,7 6,2 7,6 9,0 11,0 12,9 16,2 20,5 24,8 30,0 37,6 45,2 58,1 76,2 90,5 100,0
15
10 3,1 0,0 2,9 3,5 4,2 4,8 5,5 6,1 7,7 10,0 12,6 15,8 19,7 24,2 29,7 35,5 44,2 54,8 67,7 80,6 92,6 100,0
15 4,3 0,0 3,3 4,0 4,4 5,1 6,5 8,1 9,8 12,1 15,1 18,6 22,8 27,9 34,4 41,9 51,2 62,8 74,4 86,0 94,4 100,0
15 5,3 0,0 2,6 3,2 3,6 4,2 5,1 6,6 8,1 9,8 12,1 15,1 18,5 22,6 27,5 34,0 43,0 54,7 66,0 77,4 88,7 100,0
25
20 7,2 0,0 2,8 3,5 3,9 4,3 5,3 6,5 7,9 9,7 12,2 15,3 18,5 22,2 27,5 34,7 42,8 52,8 63,9 75,0 87,5 100,0
25 12,0 0,0 2,9 3,2 3,9 5,4 6,8 8,3 10,2 12,5 15,0 18,3 22,7 28,3 35,3 42,5 49,6 58,3 67,9 78,3 89,2 100,0
25 13,6 0,0 2,9 3,7 4,5 5,5 6,6 8,1 10,1 12,5 15,4 19,1 23,0 27,9 34,1 41,2 49,6 58,8 68,4 78,7 89,0 100,0
40
32 20,2 0,0 2,4 3,0 3,5 4,2 5,1 6,4 8,2 10,4 12,9 15,8 19,0 22,8 27,8 34,2 43,3 54,5 64,4 74,3 85,6 100,0
40 23,8 0,0 2,5 2,9 3,7 4,6 5,7 7,1 9,0 11,3 13,7 16,8 20,8 25,2 31,5 38,7 47,5 58,0 67,2 76,5 87,0 100,0
32 21,0 0,0 2,3 2,9 3,5 4,3 5,1 6,2 7,9 10,0 12,5 15,2 18,3 21,9 26,7 32,9 43,0 55,2 65,5 76,2 87,4 100,0
50
40 24,6 0,0 2,4 2,8 3,3 4,1 5,4 6,9 8,5 10,6 13,1 16,3 19,8 24,0 29,8 37,4 47,2 56,9 66,3 76,8 87,8 100,0
50 37,0 0,0 2,4 3,0 3,9 5,1 6,4 7,8 9,8 12,2 15,0 18,4 22,7 28,4 34,9 41,9 50,7 59,5 68,9 79,2 89,2 100,0
40 17,5 0,0 2,6 3,7 4,6 5,4 6,3 7,4 8,9 10,9 13,2 16,0 19,2 22,9 26,9 31,4 37,3 44,6 53,9 66,9 82,3 100,0
65
50 26,0 0,0 2,7 3,8 5,0 6,2 7,6 9,2 11,2 13,5 15,9 18,8 22,5 26,5 31,8 37,7 45,2 54,2 64,5 76,5 88,5 100,0
65 52,0 0,0 1,5 2,5 3,3 4,0 4,9 6,2 8,0 10,6 13,5 17,5 22,3 28,3 37,1 47,1 60,6 72,3 80,6 87,7 93,8 100,0
50 42,0 0,0 2,0 2,4 2,9 3,6 4,5 5,5 6,8 8,3 10,0 11,9 14,3 16,9 20,5 25,0
80
65 70,0 0,0 2,0 2,4 2,9 3,6 4,4 5,4 6,7 8,1 9,7 11,7 14,2 17,4 22,0 27,9 36,1 46,4 58,0 71,4 85,7 100,0
80 100,0 0,0 2,1 2,6 3,2 4,2 5,5 7,0 8,6 10,5 12,9 16,0 20,0 25,0 31,9 40,0 49,5 60,0 71,0 83,0 92,4 100,0
100
Tab. 2:
65 75,0 0,0 1,9 2,3 2,8 3,5 4,2 5,1 6,2 7,6 9,1 11,1 13,7 16,8 21,2 26,7 33,6 42,7 54,0 68,0 83,3 100,0
80 115,0 0,0 1,8 2,3 2,9 3,7 4,8 6,1 7,6 9,6 12,0 14,8 18,3 23,0 30,0 38,3 47,4 56,5 66,3 77,4 88,5 100,0
100 140,0 0,0 2,3 2,8 3,3 4,1 5,1 6,4 7,9 9,6 11,8 14,6 18,4 22,9 29,1 36,4 46,1 59,3 72,5 84,3 93,3 100,0
Flow rate Kv
Kvs
[m³/h]
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
Valve stroke POS [%]
30,7 38,1 46,8 59,5 76,4 100,0
english
13
Typ 8750
Control and display elements
8. CONTROL AND DISPLAY ELEMENTS
Designation:
Function of
the keys
left
POS
POS
XXX
%
MENU INPUT CMD MANU
MENU OPN CLS AUTO
selection key
Arrow key
up arrow
Fig. 8: Description of control elements
Short description
of the value
Display for operating state AUTOMATIC:
Bar running from left to right
Unit or per-
centage of the
POS
value
Save symbol
MENU CMD POS MANU
Display for position
control
Fig. 9: Description of display
0.0
0.0
Function of the keys
Display
right
selection key
Arrow key
down arrow
Value
Symbols
1)
Bar graph
display of the
value
8.1. Function of the keys
The functions of the 4 keys differ depending on the operating state
(AUTOMATIC or MANUAL) and operating level (process level or
setting level).
The function of the keys is displayed in the gray text field which is
above the key.
Function of the keys on the process level:
Key
Arrow key
Arrow key
Selection
key
Selection
key
Function of
the keys
MENU
OPN
(OPEN)
MENU
CLS
(CLOSE)
MENU
MENU
MENU
AUTO
MENU
MANU
Description of the
function
Manual opening of the
actuator
Change the displayed value
(z.B. POS-CMD-TEMP-...)
Manual closing of the actuator
Change the displayed value
(e.g. POS-CMD-TEMP-...)
Change to the setting level
Note: Press key for approx.
3 s.
Return to AUTOMATIC operating state
Change to MANUAL operating
state
Operating
state
MANUAL
AUTOMATIC
MANUAL
AUTOMATIC
AUTOMATIC
or MANUAL
MANUAL
AUTOMATIC
1) Symbols are displayed according to the activated functions
14
english
Typ 8750
Control and display elements
Function of the keys on the setting level:
Key
Arrow key Scroll up in the menus
Arrow key
Selection
key
Selection
key
Tab. 3: Function of the keys
Function of the
keys
MENU
+
MENU
–
←
MENU
MENU
EXIT
(BACK)
MENU
ESC
MENU
STOP
MENU
ENTER
MENU
SELEC
MENU
OK
MENU
INPUT
MENU
EXIT
(BACK)
MENU
RUN
MENU
STOP
Description of the function
Increase numerical values
Scroll down in the menus
Decrease numerical values
Change by one digit to the left; when
entering numerical values
Return to the process level
Gradually return from a sub-menu
option
Leave a menu
Stop a sequence
Select, activate or deactivate a menu
option
Gradually return from a sub-menu
option
Start a sequence
Stop a sequence
8.2. Operating state
The process controller has 2 operating states:
AUTOMATIC and MANUAL
POS
MENU CMD POS MANU
POS
MENU OPN CLS AUTO
0.0
0.0
8.2.1. Changing the operating state
Use the right selection key to switch between the two operating states
MENU
AUTOMATIC
AUTO
Switching from
AUTOMATIC MANUAL
Switching from
MANUAL
Tab. 4: Changing the operating state
2) Only possible if POS, CMD, PV (,SP) is displayed.
AUTOMATIC
AUTOMATIC
In the AUTOMATIC operating state, normal
controller mode is implemented.
(Bar running along the upper edge of the
display and symbol
displayed).
MANUAL
In the MANUAL operating state, the valve
can be opened and closed manually via the
arrow keys
and MANUAL
MENU
MANU
MENU
AUTO
MENU
OPN
MENU
MANU
2)
.
/
MENU
CLS
press
press
.
english
15
Typ 8750
Control and display elements
8.3. Operating levels
The process controller has 2 operating levels:
• Process level
Display and operation of the current process
Operating state: AUTOMATIC / MANUAL
• Setting level
Inputting the operating parameters
Supplementing the menu by optional menu options
8.3.1. Switching between the operating levels
Switching from
process level setting level
Switching from
setting level process level
Tab. 5: Changing the operating level
If the device is in the AUTOMATIC operating state when
changing to the setting level, the process continues running
during the setting.
POS
0.0
MENU CMD POS MANU
approx. 3 s
Fig. 10: Operating levels
3)
MENU
MENU
Process level
MENU
MENU
MENU
EXIT
Setting level
press for 3 s
press
MENU
EXIT
M A I N
POS
X.TUNE
ADD.FUNCTION
EXIT ENTER
2
8.4. Display in AUTOMATIC operating
state
Description of the display Display
Set-point position of the valve actuator
(0 – 100 %)
Nominal position of the valve actuator
(0 – 100 %)
3)
Internal temperature in the body of the device
( °C)
Process actual value
Process set-point value
POS
MENU SP/PV CMD MANU
CMD
MENU POS TEMP MANU
TEMP
C
MENU CMD PV
PV
m3/min
MENU TEMP SP MANU
SP
m3/min
MENU PV PV
0.0
0.0
0.0
0.0
0.0
(t)
INPUT
3) During these 3 s (countdown), 2 bars converge.
16
english
Typ 8750
Control and display elements
Description of the display Display
Simultaneous display of the nominal position
and the set-point position of the valve
actuator (0 – 100 %)
Graphical display of SP and PV with time
axis
Graphical display of POS and CMD with
time axis
Value overview
Pressure sensor P1 and P2
Time, weekday and date
Automatic adjustment of the position
controller
SP
m3/min
PV
m3/min
CMD/POS
MENU
MENU HOLD
CMD / POS (t)
MENU HOLD
P1 bar
P2 bar
MENU P.LIN SP/PV MANU
12:00
Thu. 01 . 09 . 11
POS
MENU
SP / PV (t)
CLOCK
(t)
X.TUNE
0.0
0.0
POS MANU
0.0
0.0
00
INPUT
X.TUNE
CLOCK
MENU
P.TUNE RUN
Description of the display Display
Automatic optimization of the process controller parameters
Automatic linearization of the process
characteristics
Simultaneous display of the nominal position
and the set-point position of the valve
actuator
(0 – 100 %)
Tab. 6: Display in the AUTOMATIC operating state
P.TUNE
X.TUNE
MENU
P.LIN RUN
P.LIN
CMD/POS
P.TUNE
MENU
CMD
POS
MENU P.LIN SP/PV MANU
RUN
0.0
0.0
8.5. Master code
Operation of the device can be locked via a freely selectable user
code. In addition, there is a non-changeable master code with which
you can perform all operator control actions on the device. This
4-digit master code can be found on the last pages of this quickstart
guide in the Chapter “Master code”.
If required, cut out the code and keep it separate from this quickstart
guide.
english
17
Typ 8750
Assembly
9. ASSEMBLY
9.1. Safety instructions
DANGER!
Risk of injury from high pressure in the equipment/device.
▶ Before working on equipment or device, switch off the pressure
and deaerate/drain lines.
Risk of electric shock.
▶ Before reaching into the device, switch off the power supply and
secure to prevent reactivation.
▶ Observe applicable accident prevention and safety regulations for
electrical equipment.
WARNING!
Risk of injury from improper assembly.
▶ Installation must only be carried out by authorized technicians and
with the appropriate tools.
Risk of injury from unintentional activation of the system and
uncontrolled restart.
▶ Secure system against unintentional activation.
▶ Following assembly, ensure a controlled restart.
9.2. Before installation
The FMR can be installed in any position, preferably with the
process controller face up.
• To avoid turbulent flows around the pressure sensor, fit an
inlet section upstream of the FMR (dimensions acc. to EN
ISO 5167-1, see “Fig. 5: Inlet sections”, page 10)
• Ensure that the pipelines are correctly lined and are not
twisted. If necessary, pipelines must be suitably attached or
supported.
• Observe flow direction (arrow on valve body).
9.2.1. Installation
→ Clean pipelines and joints (sealing material, swarf, etc.).
→ Connect FMR to pipeline.
9.3. Pneumatic connection of the
process controller
DANGER!
Risk of injury from high pressure in the equipment/device.
▶ Before working on equipment or device, switch off the pressure
and deaerate/drain lines.
18
english
Typ 8750
Assembly
WARNING!
Risk of injury from unsuitable connection hoses.
Hoses which cannot withstand the pressure and temperature
range may result in hazardous situations.
▶ Use only hoses which are authorized for the indicated pressure
and temperature range.
▶ Observe the data sheet specifications from the hose manufacturers.
Exhaust air port
label: 3
Procedure:
→ Connect the control medium to the pilot air port (1)
(3 – 7 bar; instrument air, free of oil, water and dust).
→ Fit the exhaust air line or a silencer to the exhaust air port (3).
Important information for the problem-free functioning of the
device:
• The installation must not cause back pressure to build up.
• To make the connection, select a hose with sufficient cross
section.
• The exhaust air line must be designed in such a way that
no water or other liquid can get into the device through the
exhaust air port (3).
Pilot air port
label: 1
Fig. 11: Pneumatic connection
Caution (exhaust air concept):
In compliance with protection class IP67, an exhaust air line
must be installed in the dry area.
The applied pilot pressure must always be maintained at
least 0.5 – 1 bar above the pressure which is required
to move the pneumatic actuator to its end position. This
ensures that the control behavior is not extremely negatively
affected in the upper stroke range on account of too little
pressure difference.
During operation, keep the fluctuations of the pilot pressure
as low as possible (max. ±10 %). If fluctuations are greater,
the control parameters measured with the X.TUNE function
are not optimum.
english
19
Typ 8750
Electrical installation
10. ELECTRICAL INSTALLATION
DANGER!
Risk of electric shock.
▶ Before reaching into the device, switch off the power supply and
secure to prevent reactivation.
▶ Observe applicable accident prevention and safety regulations
for electrical equipment.
WARNING!
Risk of injury from improper installation.
▶ Installation must only be carried out by authorized technicians and
with the appropriate tools!
Risk of injury from unintentional activation of the system and
uncontrolled restart.
▶ Secure system against unintentional activation.
▶ Following assembly, ensure a controlled restart.
10.1. Electrical installation, 24 V DC with
circular plug-in connector (multi-pole
variant)
Signal values
Operating voltage 24 V DC
Set-point value (process controller) 0 – 20 mA; 4 – 20 mA
0 – 5 V; 0 – 10 V
Actual value 4 – 20 mA
Procedure:
→ Connect the process controller according to the following tables.
When the operating voltage is applied, the process controller is
operating.
→ Now enter the required basic settings and actuate automatic
adjustment of the process controller, as described in Chapter
“11. Start-up 24 V DC”, page 25.
20
english
Loading...