Brother PT-D210 User's Guide

WARNING

CAUTION

Print head

Tape cutter lever

Cassette cover

Toothed Wheel

Cutter’s edge

End of tape

Tape exit slot

Tape guide

AC adapter jack

User’s Guide

English

With your new Brother P-touch labeller, you can create a wide variety of custom, self-adhesive labels. This labeller uses Brother "TZe" tapes from 3.5 mm to 12 mm widths. "TZe" tape cassettes are available in many colours and sizes. Visit

www.brother.com

your machine. Read this manual carefully before starting and keep the manual in a handy place for future reference.

D011UL001

for a complete list of tapes compatible with

Safety Precautions

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious

Follow these guidelines to avoid the risk of fire, burns, injury, electric shocks, rupture, overheating, abnormal odours or smoke.

• Always use the specified voltage and the suggested AC adapter (AD-24ES) for the P-touch labeller to prevent any damage or failure.

• Do not touch the P-touch labeller during a lightning storm.

• Do not use the P-touch labeller/AC adapter in places of high humidity such as bathrooms.

• Do not overload the power cord.

• Do not place heavy objects on, or damage, the power cord or plug. Do not forcibly bend or pull the power cord. Always hold the AC adapter when disconnecting from the electrical socket.

• Make sure that the plug is fully inserted into the electrical socket. Do not use a socket that is loose.

• Do not allow the P-touch labeller/AC adapter/power plug/batteries to get wet, for example, by handling them with wet hands or spilling liquids on them.

• Since loss of eyesight may occur when leaked fluid from batteries gets into your eyes, immediately rinse your eyes with a large amount of clean water, and then seek medical attention.

• Do not disassemble or modify the P-touch labeller/AC adapter/batteries.

• Do not allow a metal object to contact both the plus and minus ends of a battery.

• Do not use sharp objects, such as tweezers or a metallic pen, to change the batteries.

• Do not throw the batteries into fire or expose to heat.

• Disconnect the AC adapter and remove batteries immediately and stop using the P-touch labeller if you notice abnormal odour, heat, discolouration, deformation or anything unusual while using or storing it.

• Do not use a damaged or leaking battery as the fluid may get on your hands.

•

Do not use a deformed or leaking battery or one whose label is damaged as it may generate excessive heat.

injuries.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injuries.

Follow these guidelines to avoid personal injury, liquid leakage, burns or heat.

• When the P-touch labeller is not being used, store it out of the reach of children. In addition, do not allow children to put the P-touch labeller parts or labels in their mouths. If any object has been swallowed, seek medical attention.

• Do not touch metal parts around the print head immediately after printing.

• Do not touch the cutter blade.

• If leaked fluid from batteries gets on your skin or clothes, immediately rinse them with clean water.

• Remove the batteries and disconnect the AC adapter if you do not intend to use the P-touch labeller.

• Do not use a battery other than that specified. Do not use combinations of old and new batteries or combinations of different types, different charging levels, different manufacturers or different models. Do not insert a battery with its plus and minus ends reversed.

• Do not drop or hit the P-touch labeller/AC adapter.

• Do not press the Liquid-Crystal Display (LCD).

• Do not put your finger inside the P-touch labeller when you close the cassette cover.

• Before using Ni-MH rechargeable batteries, carefully read the instructions for the batteries and battery charger, and be sure to use them correctly.

• When using Ni-MH rechargeable batteries, charge the batteries with a specialised battery charger before using the batteries. The AC adapter (AD-24ES) cannot be used to recharge Ni-MH rechargeable batteries.

General Precautions

• Depending on the location, material, and environmental conditions, the label may unpeel or become irremovable, the colour of the label may change or be transferred onto other objects. Before applying the label, check the environmental conditions and the material.

• Do not use the P-touch labeller in any way or for any purpose not described in this guide. Doing so may result in accidents or damage the P-touch labeller.

•

Use only Brother TZe tapes with the P-touch labeller. Do not use tapes that do not

have the mark.

• Only use a soft, dry cloth to clean the labeller; never use alcohol or other organic solvents.

• Use a soft, lint free cloth to clean the print head. Never touch the print head directly with your hands.

• Do not put any foreign objects into the tape exit slot, AC adapter connector, battery compartment, etc.

• Do not place the P-touch labeller/batteries/AC adapter in direct sunlight or rain, near heaters or other hot appliances, in any location exposed to extremely high or low temperatures (e.g., on the dashboard or in the back of your car) or high humidity, or in dusty locations.

• Do not apply excessive pressure to the cutter lever.

• Do not try to print if the cassette is empty; it will damage the print head.

• Do not pull the tape while printing or feeding; it will damage the tape and the P-touch labeller.

• Any data stored in memory will be lost due to failure, repair of the P-touch labeller, or if the battery discharges completely.

• The P-touch labeller is not equipped with a charging feature for rechargeable batteries.

• The printed text may differ from the text that appears on the LCD.

• The length of the printed label may differ from the displayed label length.

• A protective clear plastic sticker is placed over the display during manufacturing and shipping. This sticker should be removed prior to use.

• When power is disconnected for more than three minutes, all text, format settings and any text files stored in the memory will be cleared.

Declaration of Conformity (Europe/Turkey Only)

We, Brother Industries, Ltd.

15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561 Japan

declare that this product and AC adapter are in conformity with the essential requirements of all relevant directives and regulations applied within the European Community.

The Declaration of Conformity (DoC) can be downloaded from the Brother Solutions Center. Visit http://support.brother.com/ and:

• select "Europe"

• select your country

• select "Manuals"

• select your model

• select "Declaration of Conformity"

• click "Download"

Your Declaration will be downloaded as a PDF file.

GETTING STARTED

Power Supply and Tape Cassette

Open the cassette cover by pressing the above indicated area at the top end of the machine.

• If a tape cassette is already installed, remove it by pulling it straight up. If batteries are already inserted, remove them.

• The power must be turned off when replacing batteries or tape cassettes.

Insert six new AAA alkaline batteries (LR03) or fully charged Ni-MH batteries (HR03), making sure their poles point in the correct directions.

• Users of alkaline batteries: Always replace all six batteries at the same time with brand new ones.

• Users of Ni-MH batteries: Always replace all six batteries at the same time with fully charged ones.

Insert a tape cassette, making sure it locks into place.

• The end of the tape must feed under the tape guides.

• Use only Brother TZe tapes with this machine.

Securely close the cassette cover, making sure it locks into place.

NOTE

When using AC adapter (AD-24ES)

1. Insert the plug on the adapter cord into

the AC adapter socket on the top end of the machine.

2. Insert the plug into the nearest standard

electrical socket. For memory backup, we recommend using AAA alkaline batteries (LR03) or Ni-MH batteries (HR03) together when using the AC adapter.

LCD and Keyboard

8 9

10 11

23 24

18 28

Initial Setup

Accessories

1. Size

2. Cursor

3. Underline/Frame

4. Width

5. Style

6. Caps

7. Label Length

If a specific label length has been selected, also appears.

8. OK key

9. Cursor key: Right (Use

with Shift key to go to end of the text.)

10. Cursor key: Left (Use with Shift key to go to top of the text.)

11. Escape key

12. Power key

13. Menu key

14. Label key

Carton Contents

P-touch Starter Tape Cassette User's Guide

The default setting is [English].

15. Font key

16. Character key

17. Caps key

18. Shift key

19. Tape cutter lever

20. Print key

21. Preview key

22. Frame key

23. Symbol key

24. Template Library key

25. Backspace key

26. Enter key

27. Accent key

28. Space key

NOTE

• The LCD shows one row of 15 characters; however, the text you enter can be up to 80 characters in length.

• While selecting the settings, press the Space key to go back to the default item.

• Pressing the Preview key displays a generated image of the label, which may differ from the actual label when printed.

• The label length shown on the LCD may differ slightly from the actual label length when printed.

Specifications

Dimensions: (W x D x H)

Weight: Approx. 490 g

Power supply: Six AAA alkaline batteries (LR03)

Tape cassette: Brother TZe tape (width)

*1Visit the Brother Solutions Center at

http://support.brother.com information about the recommended batteries.

Approx. 157(W) x 150(D) x 68(H) mm

(without batteries and tape cassette)

Six AAA Ni-MH batteries (HR03)* AC adapter (AD-24ES)

3.5 mm, 6 mm, 9 mm, 12 mm

for the latest

1 Turn your machine on.

Insert six AAA batteries or connect the AC

adapter (AD-24ES), and then press .

2 Set the language.

/ [Language]

/ [English/Español/Français/ Hrvatski/Italiano/Magyar/Nederlands/ Norsk/Polski/Português/Portug. (BR)/ Română/Slovenski/Slovenský/Suomi/ Svenska/Türkçe/Čeština/Dansk/Deutsch]

3 Set the unit of measurement.

The default setting is [mm].

/ [Unit]

/ [inch/mm] .

NOTE

• The machine automatically turns off if you press no key within five minutes.

• To cancel any operation, press .

• After pressing , "Accepted" appears for about one second.

LCD Contrast Adjustment

This function allows you to set the brightness of the LCD. You can select from five levels of brightness. The default setting is [0].

/ [LCD Contrast]

/ [-2/-1/0/+1/+2]

• To change back to the default setting, press the Space key.

• After pressing , "Accepted" appears for about one second.

Tape Cassettes:

Visit the Brother Solutions Center at http://support.brother.com/ for the latest information about consumables.

AC Adapter: AD-24ES

Cutter Unit: TC-4 (replacement)

If the cutter blade becomes blunt after repetitive use and the tape cannot be cut cleanly, replace with a new cutter unit (supplies code TC-4) you can obtain from an authorised Brother dealer.

 Replacing the Cutter Unit

1. Pull out the two sections of the cutter unit

(green) in the direction of the arrows shown in the illustration.

2. Install a new cutter unit. Push it in until it locks

into place.

WARNING

Do not touch the cutter blade directly with your fingers.

BASIC USAGE

Caps

Entering Text

 Switching Upper Case/Lower Case

Upper case ( ON) Lower case ( OFF)

 Creating Two-Line Labels

Move the cursor to where you want to start the

next line and press . Use either 9 mm or 12 mm wide tape for two-line printing.

Line 1 Label image

Line 2

NOTE

• The return symbol ( ) appears if you press the Enter key.

 Entering Tabs

/ [Tab]

• A appears if you insert a tab into the text.

• The maximum number of tabs for a label is 80 (without text). If you enter one letter, you can enter 79 tabs.

 Changing Tab Length

/ [Tab Length]

/ [Auto/0-100 mm]

• To change the setting back to default, press the Space key. The default setting is [Auto].

• After pressing , "Accepted" appears for about one second.

 Entering Accented Characters

- / /

• Refer to the table of accented characters included in this insertion sheet.

• To cancel operations, press .

• The order of accented characters differs by the selected LCD language.

 Changing Label Length

/ [Label Length]

/ [Auto/30-300 mm]

NOTE

• After the label is printed, cut along the printed dots (:) with scissors so that the label length matches what is shown on the LCD.

• If a specific label length has been selected, also appears in the LCD.

• To use [Auto], press the Space key.

• To change the setting back to default, press the Space key.

• After pressing , "Accepted" appears for about one second.

 To Clear

Press to delete individual letters. To delete all text and settings:

+ / [Text&Format]

To delete text only:

+ / [Text Only]

NOTE

• To delete all text and settings or text only by pressing

/ [Clear]

/ [Text&Format]/[Text Only]

•

After pressing , "Accepted" appears for about one second.

Printing Labels

 Preview

You can preview the text before printing.

• Press the Preview key to display a generated image of the label (it may differ from the actual label when printed).

• When the LCD cannot display all the text at once, press / to display the hidden text.

• Press / / to leave the preview mode.

 Feeding (Tape Feed)

• This function feeds approximately 25 mm of blank tape.

 Printing

[Copies: ] / / -

• To print only one copy of the label, press without selecting the number of copies.

• You can print up to nine copies of each label.

• To specify the number of copies, press a number key.

• To cut the label, push in the tape cutter lever in the upper-right corner of the machine after the message "Please Cut" appears.

• To prevent damage to the tape, do not touch the cutter lever while the "Please Wait" message is displayed.

• To remove the backing, fold the label lengthwise with the text facing inward, to uncover the inside edges of the backing. Peel off the backing one piece at a time and apply.

 Using Print Options ( + )

[Numbering]

You can print a series of up to nine labels at a time using auto-numbering. The number of labels you can print at one time depends on the initial number.

Example: To print copies of a label containing a

serial number (0123, 0124 and 0125):

Enter numbers / Move the cursor to the number you wish to increase

/ [Numbering] /

• When selecting the number you want to increase, always select the highest number.

[Mirror] Example: To Mirror Print "J.SMITH", enter

"J.SMITH" and follow the instructions:

Enter text/characters

/ [Mirror] [Mirror Print?]

• Use a clear tape in [Mirror], so the labels can be read correctly from the opposite side when attached on glass, windows or other transparent surfaces.

+ 5 hidden pages