Brother HL 1660e User Manual
Brother Laser Printer
HL-1660e
USER’S GUIDE
Trademarks
Brother is a registered trademark of Brother Industries, Ltd.
Apple and LaserWriter are registered trademarks, and TrueType is a trademark of
Apple Computer, Inc.
Centronics is a trademark of Genicom Corporation.
EPSON is a registered trademark, and FX-850 and FX-80 are trademarks of Seiko
Epson Corporation.
Hewlett-Packard, HP and PCL are registered trademarks, and HP LaserJet 5, HP
LaserJet 4+, HP LaserJet Plus, HP LaserJet II, HP LaserJet IID, HP LaserJet IIID,
HP-GL, HP-GL/2, and Bi-Tronics are trademarks of Hewlett-Packard Company.
IBM, Proprinter XL, Proprinter, and IBM/PC are registered trademarks of
International Business Machines Corporation.
Intellifont is a registered trademark of AGFA Corporation, a division of Miles,
Inc.
Microsoft and MS-DOS are registered trademarks of Microsoft Corporation.
Windows is a registered trademark of Microsoft Corporation in the United States
and other countries.
PostScript is a registered trademark of Adobe Systems Incorporated.
All other brand and product names mentioned in this user’s guide are registered
trademarks or trademarks of respective companies.
Compilation and Publication
Under the supervision of Brother Industries Ltd., this manual has been compiled
and published, covering the latest product descriptions and specifications.
The contents of this manual and the specifications of this product are subject to
change without notice.
Brother reserves the right to make changes without notice in the specifications
and materials contained herein and shall not be responsible for any damages
(including consequential) caused by reliance on the materials presented, including
but not limited to typographical and other errors relating to the publication.
©1997 Brother Industries Ltd.
Shipment of the Printer
If for any reason you must ship your Printer, carefully package the Printer to avoid any
damage during transit. It is recommended that you save and use the original packaging. The
Printer should also be adequately insured with the carrier.
WARNING
When shipping the Printer, the TONER CARTRIDGE must be removed from the Printer.
Failure to remove the Toner Cartridge during shipping will cause severe damage to
the Printer and will VOID THE WARRANTY.
II
Laser Printer
HL-1660e
USER’S GUIDE
(For USA & CANADA Only)
For technical and operational assistance, please call:
In USA 1-800-276-7746 (outside California)
949-859-9700 Ext. 329 (within California)
In CANADA 1-800-853-6660
514-685-6464 (within Montreal)
If you have comments or suggestions, please write us at:
In USA Printer Customer Support
Brother International Corporation
15 Musick
Irvine, CA 92718
In CANADA Brother International Corporation (Canada), Ltd.
- Marketing Dept.
1, rue Hôtel de Ville
Dollard-des-Ormeaux, PQ, Canada H9B 3H6
BBS
For downloading drivers from our Bulletin Board Service, call:
In USA 1-888-298-3616
In CANADA 1-514-685-2040
Please log on to our BBS with your first name, last name and a four digit number for your
password. Our BBS supports modem speeds up to 14,400, 8 bits no parity, 1 stop bit.
Fax-Back System
Brother Customer Service has installed an easy to use Fax-Back System so you can get
instant answers to common technical questions and product information for all Brother
products. This is available 24 hours a day, 7 days a week. You can use the system to send the
information to any fax machine, not just the one you are calling from.
Please call 1-800-521-2846 (USA) or 1-800-681-9838 (Canada) and follow the voice prompts to
receive faxed instructions on how to use the system and your index of Fax-Back subjects.
DEALERS/SERVICE CENTERS (USA only)
For the name of an authorized dealer or service center, call 1-800-284-4357.
SERVICE CENTERS (Canada only)
For service center addresses in Canada, call 1-800-853-6660
INTERNET ADDRESS
For technical questions and downloading drivers: http://www.brother.com
i
Definitions of Warnings, Cautions, and Notes
The following conventions are used in this User’s Guide:
Warning
Indicates warnings that must be observed to prevent possible
personal injury.
Caution
!
Indicates cautions that must be observed to use the printer properly or
prevent damage to the printer.
✒Note
Indicates notes and useful tips to remember when using the printer.
To Use the Printer Safely
Warning
The fixing roller is extremely hot during operation. Remove the
paper carefully.
ii
TABLE OF CONTENTS
TABLE OF CONTENTS
IMPORTANT INFORMATION: REGULATIONS..........................ix
CHAPTER 1 GENERAL..............................................................1-1
ABOUT THIS MANUAL......................................................................1-1
ABOUT CHAPTERS ON THE CD-ROM.............................................1-3
ABOUT THIS PRINTER.......................................................................1-4
Features.............................................................................................1-4
Options..............................................................................................1-10
CHAPTER 2 GETTING STARTED..............................................2-1
BEFORE USING THE PRINTER.........................................................2-1
Checking the Components................................................................2-1
Printer Carton..............................................................................2-1
Toner Cartridge...........................................................................2-2
General View.....................................................................................2-3
Operating and Storage Environment ................................................2-4
Power Supply..............................................................................2-4
Environment................................................................................2-4
SETTING UP THE PRINTER...............................................................2-5
Opening and Closing the Printer.......................................................2-5
Removing the Protective Parts..........................................................2-6
Installing the Toner Cartridge...........................................................2-7
Loading Paper in the Paper Cassette.................................................2-11
Connecting the Printer to Your Computer.........................................2-17
Turning the Printer On and Off.........................................................2-19
Plugging in the Power Cord .......................................................2-19
Pressing the POWER Switch.......................................................2-20
Printing the Test Patterns or Lists.....................................................2-21
Checking the Printed Test Pattern or Demo Page.............................2-24
iii
USER’S GUIDE
CHAPTER 3 BEFORE WORKING WITH THE PRINTER............3-1
SOFTWARE COMPATIBILITY ............................................................3-1
AUTOMATIC EMULATION SELECTION ..........................................3-3
AUTOMATIC INTERFACE SELECTION............................................3-5
ABOUT THE CONTROL PANEL.........................................................3-7
Adjusting the Control Panel Angle ...................................................3-7
Selecting the Local Language Display .............................................3-8
Using the Panel Switches..................................................................3-9
Printer Settings.................................................................................. 3-10
User Settings...............................................................................3-10
Factory Settings...........................................................................3-10
PAPER HANDLING ..............................................................................3-11
Print Media .......................................................................................3-11
Paper Size....................................................................................3-11
Using Envelopes..........................................................................3-13
Cassette Feed....................................................................................3-15
Manual Feed .....................................................................................3-16
Face Down Print Delivery.................................................................3-17
Face Up Print Delivery.....................................................................3-17
CHAPTER 4 CONTROL PANEL ................................................4-1
DISPLA Y AND LAMPS........................................................................4-1
Display..............................................................................................4-1
Printer Status Messages...............................................................4-2
Lamps ...............................................................................................4-4
READY.......................................................................................4-4
DATA...........................................................................................4-4
ALARM......................................................................................4-4
ON LINE.....................................................................................4-4
iv
TABLE OF CONTENTS
SWITCHES IN NORMAL MODE........................................................4-5
SEL Switch.......................................................................................4-5
SET Switch......................................................................................4-6
▲ (UP) or ▼ (DOWN) Switch.........................................................4-6
MODE Switch..................................................................................4-7
MODE Switch Settings in HP LaserJet,
EPSON FX-850, and IBM Proprinter XL Modes.......................4-8
MODE Switch Settings in BR-Script Mode................................4-11
MODE Switch Settings in HP-GL Mode.................................... 4-13
Basic Operation Procedures........................................................4-15
Operation Example: Selecting the Parallel Interface..................4-16
INTERFACE MODE...................................................................4-17
FORMAT MODE........................................................................4-20
ORIENTATION......................................................................4-20
AUTO MODE ........................................................................4-21
PAGE FORMAT MODE ........................................................4-22
GRAPHICS MODE ...............................................................4-25
RESOLUTION MODE...............................................................4-28
PAGE PROTECTION..................................................................4-31
CARD OPERATION...................................................................4-32
ADVANCED MODE ..................................................................4-41
NETWORK MODE...............................................................4-41
ERROR PRINT......................................................................4-44
CONTINUE MODE...............................................................4-44
BUZZER SETTING............................................................... 4-45
SCALABLE FONT................................................................4-45
PRINT DENSITY..................................................................4-46
INPUT BUFFER....................................................................4-46
SAVE SETTINGS..................................................................4-47
PAGE COUNTER.......................................................................4-48
EXIT MODE...............................................................................4-48
FONT Switch...................................................................................4-49
Setting the Font and Symbol Set in the HP LaserJet Mode.........4-49
Setting the Font and Character Set in the EPSON FX-850,
or IBM Proprinter XL Mode ......................................................4-54
List of Fonts................................................................................4-59
List of Symbol/Character Sets.....................................................4-60
FORM FEED Switch (REPRINT Switch) ......................................4-61
Form Feed...................................................................................4-61
Reprint Function .........................................................................4-61
CONTINUE Switch .......................................................................4-63
v
USER’S GUIDE
SWITCHES IN SHIFT MODE..............................................................4-64
SHIFT Switch .................................................................................4-64
EMULATION Switch......................................................................4-65
About Emulation Modes.............................................................4-67
ECONOMY Switch.........................................................................4-69
TONER SAVE MODE................................................................4-69
POWER SAVE MODE ...............................................................4-69
FEEDER Switch..............................................................................4-70
FEEDER......................................................................................4-70
MP FIRST...................................................................................4-72
MANUAL FEED........................................................................4-73
MP TRAY SETTING..................................................................4-73
MEDIA TYPE.............................................................................4-74
DUPLEX MODE........................................................................4-75
COPY Switch...................................................................................4-77
RESET Switch.................................................................................4-78
List of Factory Settings...............................................................4-79
TEST Switch....................................................................................4-85
HEX DUMP MODE...............................................................................4-88
CHAPTER 5 OPTIONS ...............................................................5-1
LOWER TRAY UNIT (LT-1200/LT-1600).............................................5-1
Loading Paper from the Lower Paper Cassette.................................5-1
FONT CARTRIDGE/CARD, FLASH MEMORY/HDD CARD ...........5-2
Installing a Font Cartridge/Card, Flash Memory Card and
HDD Card.........................................................................................5-2
Selecting the Optional Fonts.............................................................5-4
MODULAR I/O CARD..........................................................................5-6
RAM EXPANSION................................................................................5-7
DUPLEX UNIT (DX-1200/DX-1600)...................................................5-11
vi
TABLE OF CONTENTS
CHAPTER 6 MAINTENANCE ....................................................6-1
MAINTENANCE...................................................................................6-1
Toner Cartridge.................................................................................6-1
Toner Empty Message.................................................................6-1
Replacing the Toner Cartridge ....................................................6-2
Cleaning............................................................................................6-5
Cleaning the Printer Exterior ......................................................6-5
Cleaning the Printer Interior........................................................6-6
CHAPTER 7 TROUBLESHOOTING............................................7-1
TROUBLESHOOTING..........................................................................7-1
Operator Call Messages....................................................................7-1
Error Messages .................................................................................7-3
Service Call Messages......................................................................7-5
Possible Troubles..............................................................................7-6
Paper Jam....................................................................................7-6
Unsatisfactory Printouts..............................................................7-12
APPENDICES ........................................................................... Appendix-1
PRINTER SPECIFICATIONS ...............................................................Appendix-1
Printing .............................................................................................Appendix-1
Functions ..........................................................................................Appendix-2
Electrical and Mechanical.................................................................Appendix-3
PAPER SPECIFICATIONS....................................................................Appendix-4
INTERFACE SPECIFICATIONS...........................................................Appendix-8
Bi-directional Parallel Interface ........................................................Appendix-8
Pin Assignment............................................................................Appendix-8
Signal Description.......................................................................Appendix-9
Parallel Cable Connection for IBM-PC/AT or
Compatible Computers and IBM-PS/2 Computers...................Appendix-10
vii
USER’S GUIDE
RS-232C Serial Interface................................................................Appendix-11
Standard Specifications.............................................................Appendix-11
Interface Connectors.................................................................Appendix-11
Pin Assignment..........................................................................Appendix-11
Signal Description.....................................................................Appendix-12
Serial Cable Connection for IBM-PC/AT or
Compatible Computers and IBM-PS/2 Computers...................Appendix-13
SYMBOL/CHARACTER SETS..........................................................Appendix-15
OCR Symbol Sets...........................................................................Appendix-15
HP LaserJet Mode...........................................................................Appendix-16
EPSON Mode.................................................................................Appendix-17
IBM Mode......................................................................................Appendix-18
HP-GL Mode..................................................................................Appendix-18
Symbol Sets Supported by the Printer’s Intellifont Compatible
Typefaces........................................................................................Appendix-19
Symbol Sets Supported by the Printer’s TrueType and Type 1 Font
Compatible, and Original Typefaces...............................................Appendix-21
QUICK REFERENCE OF COMMANDS...........................................Appendix-23
HP LaserJet Mode...........................................................................Appendix-23
PCL Command Sets..................................................................Appendix-23
CCITT G3/G4 and TIFF...........................................................Appendix-36
Horizontal 1200-dpi Image Format Mode................................Appendix-39
HP-GL/2 Command Sets...........................................................Appendix-42
Printer Job Language Commands Syntax.................................Appendix-44
EPSON FX-850 Mode....................................................................Appendix-45
IBM Proprinter XL Mode...............................................................Appendix-48
HP-GL Mode..................................................................................Appendix-51
Bar Code Control............................................................................Appendix-53
INDEX...........................................................................................Index-1
viii
IMPORTANT INFORMATION: REGULATIONS
Federal Communications Commission Compliance Notice
(For U.S.A. only)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equip m ent does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
❏ Reorient or relocate the receiving antenna.
❏ Increase the separation between the equipment and receiver.
❏ Connect the equipment into an ou tlet on a circuit different from that
to which the receiver is connected.
❏ Consult the dealer or an experienced radio/TV technician for help.
REGULATIONS
Important – About the Interface Cable
This printer has been certified to comply with FCC standards, wh ich are
applied to the U.S.A. only. A shielded interface cable should be used
according to FCC 15.27(C). In addition, a grounded plug should be
plugged into a grounded AC outlet after checking the rating of the local
power supply for the printer to operate properly and safely.
Caution
☛
Changes or modifications not expressly approved by Brother Industries,
Ltd. could void the user’s authority to operate the equipment.
International Energy Star Compliance Statement (For HL-1660
series only)
The purpose of the International Energy Star Program is to promote the
development and popularization of energy-efficient office equipments, which
includes computers, monitors, printers, facsimile receivers and copy machines
world-wide.
As an International Energy Star partner, Brother Industries, Ltd. has decided that
this product meets the guideline of the program.
ix
USER’S GUIDE
Canadian Department of Communications Compliance
Statement (For Canada only)
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the interference- causing
equipment standard entitled “Digital Apparatus”, ICES-003 of the
Department of Communications.
Avis de conformité aux normes du ministère des
Communications du Canada (Pour Canada Seul)
Cet appareil numérique respecte les limites de bruits radioélectriques
applicables aux appareils numériques de Classe B prescrites dans la
norme sur le matériel brouilleur : “Appareils Numériques”, NMB-003
édictée par le ministère des Communications.
Laser Safety (110-120 V model only)
This printer is certified as a Class I laser product under the U.S.
Department of Health and Human Services (DHHS) Radiation
Performance Standard according to the Radiation Control for Health and
Safety Act of 1968. This means that the printer does not produce
hazardous laser radiation.
Since radiation emitted inside the printer is completely confined within
protective housings and external covers, the laser beam cannot escape
from the machine during any phase of user operation.
CDRH Regulations (110-120 V model only)
The Center for Devices and Radiological Health (CDRH) of the U.S.
Food and Drug Administration (FDA) implemented regulations for laser
products on August 2, 1976. These regulations apply to laser products
manufactured from August 1, 1976. Compliance is mandatory for
products marketed in the United States. The label shown on the back of
the printer indicates compliance with the CDRH regulations and must be
attached to laser products marketed in the United States.
MANUFACTURED:
BROTHER INDUSTRIES, LTD.
15-1 Naeshiro-cho Mizuho-ku Nagoya, 467 Japan
This product complies with FDA radiation performance standards, 21
CFR chapter 1 subchapter J.
x
☛ Caution: Use of controls, adjustments or performance of
procedures other than those specified in this manual
may result in hazardous radiation exposure.
Radio Interference(220-240 V model only)
This printer complies with EN55022(CISPR Publication 22)/Class B.
Before this product is used, ensure that you use a double-shielded
interface cable with twisted-pair conductors and that it is marked
“IEEE1284 compliant”. The cable must not exceed 1.8 metres in length.
IEC 825 (220-240 V model only)
This printer is a Class 1 laser product as defined in IEC 825
specifications. The label shown below is attached in countries where
required.
CLASS 1LASER PRODUCT
APPAREIL Å LASER DE CLASSE 1
LASER KLASSE 1 PRODUKT
REGULATIONS
This printer has a Class 3B Laser Diode which emits invisible laser
radiation in the Scanner Unit. The Scanner Unit should not be opened
under any circumstances.
☛ Caution: Use of controls, adjustments or performance of
procedures other than those specified in this manual
may result in hazardous radiation exposure.
The following caution label is attached on the cover of the scanner unit.
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED.
CAUTION
ADVARSEL
VARNING
VARO!
ADVARSEL
ATTENTION
VORSICHT
ATENCIÓN
AVOID DIRECT EXPOSURE TO BEAM. CLASS 3B LASER PRODUCT.
USYNLIG LASER STRÅLING NÅR KABINETLÅGET STÅR ÅBENT.
UNGDÅ DIREKTE UDSÆTTELSE FOR STRÅLING. KLASSE 3B LASER.
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR
ÄR URKOPPLADE. STRÅLEN ÄR FARLIG. KLASS 3B LASER APPARAT.
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN. LUOKAN
3B LASERLAITE.
USYNLIG LASERSTRÅLING.UNNGÅ DIREKTE KONTAKT MED LASERENHETEN
NÅR TOPPDEKSELET ER ÅPENT. KLASSE 3B LASERPRODUKT.
RADIATIONS LASER INVISIBLES QUANDOUVERT ET VERROUILLAGE ENLEVE.
EVITER EXPOSITIONS DIRECTES AU FAISCEAU. PRODUIT LASER CLASSE 3B.
UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG
GEÖFFENT UND SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.
SICHERHEITSKLASSE 3B.
RADIACIÓN LASER INVISIBLE CUANDO SE ABRE
LA TAPA Y EL INTERRUPTOR INTERNO ESTÁ
ATASCADO. EVITE LA EXPOSICIÓN DIRECTA
DE LOS OJOS. PRODUCTO LASER CLASE 3B.
xi
USER’S GUIDE
For Your Safety
For Finland and Sweden
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
☛ Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle
näkymättömälle lasersäteilylle.
Varning – Om apparaten används på annat sätt än i denna
Bruksanvisning specificerats, kan användaren utsättas för osynlig
laserstrålning, som överskrider gränsen för laserklass 1.
To ensure safe operation the three-pin plug supplied must be inserted
only into a standard three-pin power point which is effectively grounded
through the normal household wiring.
Extension cords used with the equipment must be three-conductor and be
correctly wired to provide connection to ground. Incorrectly wired
extension cords are a major cause of fatalities.
The fact that the equipment operates satisfactorily does not imply that the
power is grounded and that the installation is completely safe. For your
safety, if in any doubt about the effective grounding of the power, consult
a qualified electrician.
Wiring Information (For U.K. only)
If the mains plug supplied with this printer is not suitable for your socket
outlet, remove the plug from the mains cord and fit an appropriate three
pin plug. If the replacement plug is intended to take a fuse then fit the
same rating fuse as the original.
If a moulded plug is severed from the mains cord then it should be
destroyed because a plug with cut wires is dangerous if engaged in a live
socket outlet. Do not leave it where a child might find it!
In the event of replacing the plug fuse, fit a fuse approved by ASTA to
BS1362 with the same rating as the original fuse.
Always replace the fuse cover. Never use a plug with the cover omitted.
WARNING - THIS PRINTER MUST BE EARTHED
Important
xii
REGULATIONS
The wires in the mains cord are coloured in accordance with the
following code :
GREEN AND YELLOW : EARTH
BLUE : NEUTRAL
BROWN : LIVE
The colours of the wires in the mains lead of this printer may not
correspond with the coloured markings identifying the terminals in your
plug.
If you need to fit a different plug, proceed as follows.
Remove a length of the cord outer sheath, taking care not to damage the
coloured insulation of the wires inside.
Cut each of the three wires to the appropriate length. If the construction
of the plug permits, leave the green and yellow wire longer than the
others so that, in the event that the cord is pulled out of the plug, the
green and yellow wire will be the last to disconnect.
Remove a short section of the coloured insulation to expose the wires.
The wire which is coloured green and yellow must be connected to the
terminal in the plug which is marked with the letter “E” or by the safety
earth symbol
, or coloured green or green and yellow.
The wire which is coloured blue must be connected to the terminal which
is marked with the letter “N” or coloured black or blue.
The wire which is coloured brown must be connected to the terminal
which is marked with the letter “L” or coloured red or brown.
The outer sheath of the cord must be secured inside the plug. The
coloured wires should not hang out of the plug.
xiii
USER’S GUIDE
DECLARATION OF CONFORMITY (EUROPE)
We, Brother International Europe Ltd.,
Brother House 1 tame Street, Guide Bridge,
Audenshaw, Manchester M34 5JE, UK.
declare that this product is in conformity with the following normative
documents:
Safety: EN 60950, EN 60825
EMC: EN 55022 Class B, EN 50082-1
following the provisions of the Low Voltage Directive 73/23/EEC and
the Electromagnetic Compatibility Directive 89/336/EEC (as amended by
91/263/EEC and 92/31/EEC).
Manufacture at the following facilities is carried out under a Quality
System which is registered by BSI Quality Assurance and JQA Quality
Assurance.
Brother Industries, Ltd., Kariya Plant
1-5, Kitajizoyama, Noda-cho, Kariya-shi,
Aichi-ken 448, Japan.
BSI Certificate of Registration No. FM27391
JQA Certificate of Registration No. 0340
xiv
Issued by:
Brother International Europe Ltd.
European Development and Technical Services Division
CHAPTER 1
GENERAL
ABOUT THIS MANUAL
This manual acts as your guide to the setup and operation of your printer
and covers the following topics:
CHAPTER 1 GENERAL provides an overview of the printer. Read this
chapter first to get familiar with the printer.
CHAPTER 2 GETTING STARTED gives you general information
about this printer. Be sure to read this chapter before you use the printer.
CHAPTER 3 BEFORE WORKING WITH THE PRINTER gives
you important information on the printer setup to work with your
computer and software. Be sure to read this chapter before you work with
the printer.
CHAPTER 1 GENERAL
CHAPTER 4 CONTROL PANEL details the functions of the panel
switches and lamps.
CHAPTER 5 OPTIONS describes the optional accessories for this
printer.
CHAPTER 6 MAINTENANCE provides guidance on how to maintain
your printer
CHAPTER 7 TROUBLESHOOTING helps you troubleshoot the
printer in case of problems.
APPENDICES contain detailed technical information on the printer as
well as the character sets and a quick reference guide to the printer
control commands.
INDEX provides an alphabetical list of the contents of this manual and
the floppy disk supplied with the printer.
1–1
USER’S GUIDE
2 Notes
When you read this user’s guide, note the following:
• This user’s guide contains instructions or steps to teach you various
operations of the printer. Remember that the instructions start with the
factory settings, particularly in Chapter 2 and Chapter 3. If you
change the settings, particularly the emulation mode, the display
messages change accordingly.
• The paper size has been factory set to letter or A4, depending upon the
final destination of the printer. Some display messages appear
differently in accordance with this setting.
1–2
ABOUT CHAPTERS ON THE CD-ROM
Installing the Adobe Acrobat Reader Software
You need to install the Adobe Acrobat Reader software to view the Online User’s guide.
1. Close all the applications running on your PC.
2. Insert the supplied compact disc into the CD-ROM drive.
3. View the contents of the CD-ROM by using Explorer (Windows
95/98/NT 4.0) or File Manager (Windows 3.1/3.11).
4. Open the sub-folder (sub-directory) which has the required language
in the folder (directory) ‘Acrobat’.
Ar16X301.exe - Windows3.1/3.11
Ar32X301.exe - Windows95/98/NT4.0
( X stands for the language version.)
5. Double click the file ‘ArXXX301.exe’ to run the instller.
After the installer starts, simply follow the instructions that appear on
the screen.
Viewing the User’s Guide and Setup Guide
CHAPTER 1 GENERAL
1. Insert the supplied compact disc into the CD-ROM drive.
2. View the contents of the CD-ROM by using Explorer or File Manager.
3. Open the sub-folder (sub-directory) which has the required language
in the folder (directory) ‘Document’.
Setupxxx.pdf - Setup Guide
Userxxx.pdf - User’s Guide
( xxx stands for the language version. )
4. Double click the file to be opened.
5. The Acrobat Reader software is automatically launched and the
required manual will be opend.
Refer to the next section ‘How to use the Adobe
How to use the Adobe Acrobat Reader
Bookmarks
The bookmarks contain the titles of each section.
To go to the destination specified by a bookmark, click the bookmark
text or double- click the page icon to the left of the bookmark name.
The texts marked with purple color have links to the related pages. The
shape of cursor pointer will be changed to the ‘finger’ when positioned
over a link. To go to the destination specified by these links, click on it.
Acrobat Reader’.
1–3
USER’S GUIDE
ABOUT THIS PRINTER
Features
This printer has the following standard features. When you need more
information on how to use a particular feature, turn to the page indicated
at the end of the paragraph.
High Speed and Quiet Laser Printing
This printer uses electrophotography technology by laser beam scanning
so that it can print at a speed of 16 pages per minute (HL-1660e). The
controller utilizes a high speed 32-bit RISC microprocessor and special
hardware chips. The quiet printing will not bother you working in your
office or at home: 52 dB A (printing)/45 dB A (stand-by).
600 DPI Resolution
This printer uses a print engine with a resolution of 600 dots per inch
(dpi). Compared with a 300-dpi engine, the quality of the output is far
superior. See page 4-28. By utilizing the 300-dpi mode, the printer can
also print 300-dpi data, if necessary. (In HP emulation you can select a
horizontal 1200-dpi mode by special control command.
See page Appendix-39.)
1–4
High Resolution Control
The high resolution control (HRC) technology provides clear and crisp
printouts and improves even the 600-dpi resolution. See 4-30.
Maintenance-Free Toner Cartridge
The toner cartridge can print up to 9,000 single-sided pages. The one
piece, easy-to-replace toner cartridge does not require difficult
maintenance. Just install it. See 2-7.
Advanced Photoscale Technology
®
This printer can print graphics in 256 shades of gray in HP
(HL-1660e only) / LaseJet 4+™ emulation and BR-Script level 2,
producing nearly photographic quality.
LaserJet 5™
CHAPTER 1 GENERAL
Universal Paper Cassette and Manual Loading
This printer loads paper automatically from the paper cassette. Since the
paper cassette is a universal type, a number of different sizes of paper can
be used. Even envelopes can be loaded from the multi-purpose tray and
the upper paper cassette. In addition, the multi-purpose tray allows you to
load paper sheet by sheet. See 3-15 for auto loading and 3-16 for manual
loading.
Four Interfaces
This printer has a high speed bi-directional parallel interface, an RS-232C
serial interface, a Universal Serial Bus (USB), and a modular input/output
(MIO) compatible interface.
If your application software supports the bi-directional parallel interface,
you can monitor the printer status. It is fully compatible with the
industry-standard bi-directional parallel interface. See page 2-17.
The RS-232C serial interface is an industry standard so that you can
connect it to any computer using a standard serial cable. See page 2-17.
The Universal Serial Bus is an interface which allows the printer connect
with multiple peripheral devices.
The MIO interface allows you to install a commercial MIO-compatible
card. If you install the card, you can use one more interface port for
features such as networking or printer sharing. See page 5-6.
Automatic Interface Selection
This printer can automatically select the bi-directional parallel, RS-232C
serial, Universal Serial Bus, or MIO interface depending on the interface
port through which it receives data. With this feature, the printer can be
connected to more than one computer. See page 3-5.
Five Emulation Modes
®
This printer can emulate the Hewlett-Packard
®
6)/ LaserJet 4+ (PCL® 5e), PostScript® Level 2 language
(PCL
laser printer-LaserJet 5
emulation (Brother BR-Script Level 2) printers, the industry-standard HPGL™ plotter as well as EPSON
®
FX-850™, and IBM® Proprinter XL
®
printers. You can print with all application programs that support one of
these printers. See page 3-1.
1–5
USER’S GUIDE
Automatic Emulation Selection
This printer can automatically select the printer emulation mode
depending on the print commands it receives from the computer software.
With this feature, many users can share the printer on a network.
See page 3-3.
Data Compression Technology
This printer can internally compress the received graphics and font data in
its memory so that it can print larger graphics and more fonts without
additional memory.
Memory Expansion
This printer has 8-Mbyte of RAM as standard. It can be expanded up to
72 Mbytes. The memory should be expanded to 6 Mbytes in total or more
to enjoy 600-dpi or APT printouts in the BR-Script 2 mode. When you
select duplex mode with an optional duplex unit installed, the memory
should be expanded to 10Mbytes in total or more to enjoy 600-dpi duplex
printing. See pages 4-28 and 5-7. (The standard memory fitted can vary
depending on the printer model and country.)
75 Scalable and 12 Bitmapped Fonts
This printer has the following scalable fonts and bitmapped fonts. The
fonts that can be used vary according to the current emulation mode.
n HP LaserJet, EPSON FX-850, and IBM Proprinter XL Modes
Scalable Fonts:
Intellifont Compatible Fonts:
• Alaska, Extrabold
• Antique Oakland, Oblique, Bold
• Brougham, Oblique, Bold, BoldOblique
• Cleveland Condensed
• Connecticut
• Guatemala Antique, Italic, Bold, BoldItalic
• Letter Gothic, Oblique, Bold
• Maryland
• Oklahoma, Oblique, Bold, BoldOblique
• PC Brussels Light, LightItalic, Demi, DemiItalic
• PC Tennessee Roman, Italic, Bold, BoldItalic
• Utah, Oblique, Bold, BoldOblique
• Utah Condensed, Oblique, Bold, BoldOblique
1–6
Microsoft® Windows® 3.1 / Windows 95/98 TrueType™
Compatible Fonts:
• BR Symbol
• Helsinki, Oblique, Bold, BoldOblique
• Tennessee Roman, Italic, Bold, BoldItalic
• W Dingbats
Type 1 Font Compatible Fonts:
• Atlanta Book, BookOblique, Demi, DemiOblique
• Calgary MediumItalic
• Copenhagen Roman, Italic, Bold, BoldItalic
• Portugal Roman, Italic, Bold, BoldItalic
Brother Original Fonts:
• Bermuda Script
• Germany
• San Diego
• US Roman
Bitmapped Fonts (Portrait and Landscape):
• LetterGothic16.66 Medium, Italic, Bold, BoldItalic
• OCR-A
• OCR-B
n BR-Script 2 Mode
CHAPTER 1 GENERAL
Scalable Fonts:
• Atlanta Book, BookOblique, Demi, DemiOblique
• Alaska, Extrabold
• Antique Oakland, Oblique, Bold
• Bermuda Script
• BR Dingbats
• BR Symbol
• Brougham, Oblique, Bold, BoldOblique
• Brussels Light, LightItalic, Demi, DemiItalic
• Calgary MediumItalic
• Cleveland Condensed
• Connecticut
• Copenhagen Roman, Italic, Bold, BoldItalic
• Germany
• Guatemala Antique, Italic, Bold, BoldItalic
• Helsinki, Oblique, Bold, BoldOblique
• Helsinki Narrow, Oblique, Bold, BoldOblique
• Letter Gothic, Oblique, Bold
• Maryland
• Oklahoma, Oblique, Bold, Bold Oblique
• Portugal Roman, Italic, Bold, BoldItalic
• San Diego
• Tennessee Roman, Italic, Bold, BoldItalic
• US Roman
• Utah, Oblique, Bold, BoldOblique
• Utah Condensed, Oblique, Bold, BoldOblique
1–7
USER’S GUIDE
High Speed Printing with Microsoft Windows 95/98/Windows
3.1
Since TrueType compatible fonts are resident in this printer, the printer
can print them with Microsoft Windows 95/98/3.1 at a high speed without
downloading them. Because the printer has a TrueType Font rasterizer, it
can rasterize fonts at a high speed.
Bar Code Print
This printer can print the following 11 types of bar codes:
• Code 39 • UPC-E
• Interleaved 2 of 5 • Codabar
• EAN-8 • US-PostNet
• EAN-13 • ISBN
• UPC-A • Code 128
• EAN-128
CCITT G3/G4
Since this printer supports the CCITT G3/G4 format in addition to HPcompatible formats, it can quickly receive and print data compressed in
this format.
Lock Panel
If the panel switch settings have been changed, the printer may not work
as you expect. You can lock your settings to prevent changes from being
made. See page 4-41.
Power Save Mode
This printer has a power saving mode. As laser printers consume power to
keep the fixing assembly at a high temperature, this feature can save
electricity when the printer is on but not being used. The factory setting of
the Power Save mode is ON that complies with EPA Energy Star new
specification. Compared with conventional laser printers, this printer
consumes less power even when the power saving mode is turned off.
See page 4-69.
Toner Save Mode
This printer has an economical toner save mode. You can cut your printer
running cost substantially by using this mode in addition to the improved
life expectancy of the toner cartridge. See page 4-69.
1–8
CHAPTER 1 GENERAL
Reprint Function
You can reprint the last job printed with a touch of a panel switch which
allows reprinting without sending the data again from the computer.
See page 4-61.
Flash Memory Card and HDD Card
You can store fonts, macros, logos, and other print data in a commercial
PCMCIA-compatible flash memory card or HDD card that is installed in
the upper card slot of this printer. See pages 4-32 and 5-2.
Saving User Settings
You can operate the printer differently from other users with your own
panel switch settings. Two sets of user settings can be stored.
See page 4-47.
1–9
USER’S GUIDE
Options
The following options are available for this printer:
Lower Tray Unit
A lower tray unit expands the paper source capacity. You can load extra
paper and switch between the upper and lower paper sources
automatically. See page 5-1.
Duplex Unit
A duplex unit enables you to print on both sides of the paper.
See page 5-11.
Technical Reference Manual
The technical reference manual contains detailed information about the
printer control commands. For programming with the printer, see this
manual which is available from your Brother dealer.
The following commercial products can be installed into this printer:
MIO Card
A commercial modular input/output (MIO) compatible sharing/network
card gives you an additional interface port for attaching the printer to a
network or sharing your printer with multiple computers. See page 5-6.
Font Cartridges
Commercial font cartridges containing additional scalable fonts or
bitmapped fonts. See page 5-2.
Flash Memory Card and HDD Card
A commercial flash memory card or a HDD card can be installed. You
can store fonts, macros, logos, and other print data in a commercial
PCMCIA-compatible flash memory card or HDD card. See pages 4-32
and 5-2.
RAM Expansion
1–10
Installing commercial memory modules expands the memory capacity up
to 72 Mbytes. See pages 5-7.
CHAPTER 2
GETTING STARTED
BEFORE USING THE PRINTER
Checking the Components
Printer Carton
When you unpack the printer, check to see that you have all of the
following parts.
CHAPTER 2 GETTING STARTED
Power Cord
Upper Paper Cassette
(installed inside the printer)
✒ Note
An interface cable is not a standard accessory. Please purchase an
appropriate cable according to the interface you intend to use. The power
cord may differ slightly from this figure depending on the country where
you purchased the printer.
Printer
User’s Guide
Windows Driver/TrueType
Compatible Font Disk #1
Windows Driver/TrueType
Compatible Font Disk #2
Fig. 2-1 Components in the Printer Carton
2–1
USER’S GUIDE
Toner Cartridge
The toner cartridge is inside the toner cartridge carton.
Caution
!
The toner cartridge is packed inside a bag. Do not open it now. Open it
immediately before you install the toner cartridge. The toner cartridge
must not be exposed to light for a long time.
Fig. 2-2 Toner Cartridge
2–2
General View
CHAPTER 2 GETTING STARTED
Font/IC Card Slot
Font Cartridge Slot
Rear Access Cover
Control Panel
A
B
Multi-purpose Tray
Upper Paper Cassette
Fig. 2-3 Front View
Adjustment Knob for
Face Up/Down Print Delivery
Bi-directional Parallel
Interface Connector
Top Cover
Power Switch
Face Down Print
Delivery Tray
Power Cord Connector
RS-232C Serial
Interface Connector
Modular Jack for
Options
Fig. 2-4 Rear View
Universa Serial
Bus connecto
r
MIO Card Slot
2–3
USER’S GUIDE
Operating and Storage Environment
Please take note of the following before using the printer.
Power Supply
Use the printer within the specified power range.
AC power: ±10% of the rated power voltage
Frequency: 50 Hz (220-240 V) or 60 Hz (110-120 V)
The power cord, including extensions, should not exceed 5 meters (16.5
feet).
Do not share the same power circuit with other high-power appliances,
particularly an air conditioner, copier, shredder, etc. If it is unavoidable
that you must use the printer with these appliances, we recommend you
use a voltage transformer or a high-frequency noise filter.
Use a voltage regulator if the power source is not stable.
Environment
Use the printer only within the following ranges of temperature and
humidity.
Ambient temperature:10°C to 32.5°C (50°F to 90.5°F)
Ambient humidity: 20% to 80% (without condensation)
Do not block the air exit on top of the printer. Do not place objects on top
of the printer, especially on the air exit.
Ventilate the room where you use the printer.
Do not place the printer where it is exposed to direct sunlight. Use a blind
or a heavy curtain to protect the printer from direct sunlight if the printer
is unavoidably set up near a window.
Do not install the printer near devices that contain magnets or generate
magnetic fields.
Do not subject the printer to strong physical shocks or vibrations. Do not
expose the printer to open flames or salty or corrosive gasses.
Place the printer on a flat, horizontal surface.
2–4
Keep the printer clean. Do not install the printer in a dusty place.
Do not install the printer near an air conditioner.
Loading...