Brocade Flush Mount Rack Kit User Manual

53-1002127-04 25 July 2014
Flush Mount Rack Kit
Installation Procedure
®
Supporting the Brocade VDX 6710-54, VDX 6720-24, VDX 6720-60, VDX 6730-32, VDX 6730-76, and VDX 6740
53-1002127-04
*53-1002127-04*
Copyright © 2010-2014 Brocade Communications Systems, Inc. All Rights Reserved.
ADX, AnyIO, Brocade, Brocade Assurance, the B-wing symbol, DCX, Fabric OS, ICX, MLX, MyBrocade, OpenScript, VCS, VDX, and Vyatta are registered trademarks, and HyperEdge, The Effortless Network, and The On-Demand Data Center are trademarks of Brocade Communications Systems, Inc., in the United States and/or in other countries. Other brands, products, or service names mentioned may be trademarks of their respective owners.
Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document at any time, without notice, and assumes no responsibility for its use. This informational document describes features that may not be currently available. Contact a Brocade sales office for information on feature and product availability. Export of technical data contained in this document may require an export license from the United States government.
The authors and Brocade Communications Systems, Inc. shall have no liability or responsibility to any person or entity with respect to any loss, cost, liability, or damages arising from the information contained in this book or the computer programs that accompany it.
The product described by this document may contain “open source” software covered by the GNU General Public License or other open source license agreements. To find out which open source software is included in Brocade products, view the licensing terms applicable to the open source software, and obtain a copy of the programming source code, please visit http://www.brocade.com/support/oscd.
Brocade Communications Systems, Incorporated
Corporate and Latin American Headquarters Brocade Communications Systems, Inc. 130 Holger Way San Jose, CA 95134 Tel: 1-408-333-8000 Fax: 1-408-333-8101 E-mail: info@brocade.com
European Headquarters Brocade Communications Switzerland Sàrl Centre Swissair Tour B - 4ème étage 29, Route de l'Aéroport Case Postale 105 CH-1215 Genève 15 Switzerland Tel: +41 22 799 5640 Fax: +41 22 799 5641 E-mail: emea-info@brocade.com
Asia-Pacific Headquarters Brocade Communications Systems China HK, Ltd. No. 1 Guanghua Road Chao Yang District Units 2718 and 2818 Beijing 100020, China Tel: +8610 6588 8888 Fax: +8610 6588 9999 E-mail: china-info@brocade.com
Asia-Pacific Headquarters Brocade Communications Systems Co., Ltd. (Shenzhen WFOE) Citic Plaza No. 233 Tian He Road North Unit 1308 – 13th Floor Guangzhou, China Tel: +8620 3891 2000 Fax: +8620 3891 2111 E-mail: china-info@brocade.com
Document History
Document Title Publication Number Summary of Changes Date
Flush Mount Rack Kit Installation Procedure 53-1002127-01 New document December 2010
Flush Mount Rack Kit Installation Procedure 53-1002127-02 Added support for VDX
6710 and VDX 6730 models
Flush Mount Rack Kit Installation Procedure 53-10002127-03 Added support for VDX
6740 model
Flush Mount Rack Kit Installation Procedure 53-1002127-04 Removed reference to
6-32 x 1/4-in. flathead Phillips screw as they are not shipped.
September 2011
July 2013
July 2014
2 of 10 Flush Mount Rack Kit Installation Procedure
53-1002127-04
Contents
This document provides instructions to install a Brocade VDX 6710-54 (1U), VDX 6720-24 (1U), VDX 6730-32 (1U), VDX 6720-60 (2U), VDX 6730-76 (2U), or VDX 6740 (1U) Flush Mount Kit. The document is organized as follows.
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Tool requirements and parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
switch in a telecommunications (Telco) rack using the
Introduction
The supported switches are listed in Table 1.
TABLE 1
Switch height Switch model
1U Brocade VDX 6710-54
2U Brocade VDX 6720-60
Supported switches
Brocade VDX 6720-24 Brocade VDX 6730-32 Brocade VDX 6740
Brocade VDX 6730-76
Installation requirements
Allow 15 to 30 minutes to complete this procedure. Note the following requirements to ensure correct installation and operation:
Verify that the additional weight of the switch does not exceed the rack’s weight limits.
Ensure that an electrical branch circuit with the following characteristics is available:
-
Required voltage and frequency as indicated in the hardware reference manual (200-230 VAC is always preferred).
-
Protection by a circuit breaker in accordance with local electrical codes.
-
Supply circuit, line fusing, and wire size that conform to the electrical rating on the switch nameplate.
-
Grounded outlet compatible with the power cord and installed by a licensed electrician.
Ensure that all equipment installed in the rack is grounded through a reliable branch circuit connection. Do not rely on a secondary connection to a branch circuit, such as a power strip.
Ensure that the rack is mechanically secured to ensure stability.
Ensure that the air temperature at the fan inlet is less than 40oC (104oF) during switch operation.
Ensure that the airflow available at the air vents meets the minimum requirements for the switch.
Flush Mount Rack Kit Installation Procedure 3 of 10 53-1002127-04
ATTENTION
Install the switch with the airflow aligned with any other switches in the rack. Some switches have airflow running from
ATTENTION
port side to fan side and others have the opposite arrangement. Make sure that the airflow for all switches moves in the same direction to maximize cooling.
Tool requirements and parts list
The following items are required to install a switch using the mid-mount rack kit:
Clamps or other means of temporarily supporting the switch in the rack.
Phillips #2 torque screwdriver
1/4-inch slotted blade torque screwdriver
Use the screws specified for use with the switch. Longer screws can damage the switch.
Ensure that the items listed in Table 2 and illustrated in Figure 1 are included in the kit.
TABLE 2
Description Quantity
Brackets, front right and left 2
Brackets, rear right and left 1
Screw, 8-32 x 5/16-in., panhead Phillips 12
Screw, 10-32 x 5/8-in., panhead Phillips 8
Retainer nut, 10-32 8
Parts list
4 of 10 Flush Mount Rack Kit Installation Procedure
53-1002127-04
ATTENTION
NOTE
1 Front brackets, right and left 4 Screw, 10-32 x 5/8-in., panhead Phillips 2 Rear brackets, right and left 5 Retainer nut, 10-32 3 Screw, 8-32 x 5/16-in., panhead Phillips
FIGURE 1
Items in the Flush Mount Rack Kit
Installation procedure
The switch must be turned off and disconnected from the fabric during this procedure.
Although this document describes how to install both single height (1U) and double height (2U) switches, the illustrations show a 2U switch as a typical installation.
Flush Mount Rack Kit Installation Procedure 5 of 10 53-1002127-04
Complete these tasks to install the switch in a rack:
1
3
“Attaching front brackets to the switch”
“Attaching front brackets to a rack”
“Attaching rear brackets to a rack”
“Attaching rear brackets to the switch”
Attaching front brackets to the switch
Complete the following steps to attach the front brackets to the switch.
1. Position the right front bracket with the flat side against the right side of the switch as shown in Figure 2.
2. Insert two 8-32 x 5/16-in. screws through the pair of vertically aligned holes in the bracket and then into the pair of holes on the side of the switch.
3. Insert another 8-32 x 5/16-in. screw through the third hole in the bracket and into the corresponding hole in the switch.
4. Repeat step 1 through step 3 to attach the left front bracket to the left side of the switch.
5. Tighten all 8-32 x 5/16-in. screws to a torque of 15 in-lbs. (17 cm-kgs).
1 Front brackets, right and left 3 Screw, 8-32 x 5/16-in., panhead Phillips
FIGURE 2
6 of 10 Flush Mount Rack Kit Installation Procedure
Attaching the front brackets
53-1002127-04
Attaching front brackets to a rack
6
5
Complete the following steps to install the switch in the rack.
1. Position the switch in the rack (Figure 3), providing temporary support under the switch until the rail kit is fully
secured to the rack.
2. Attach the right front bracket to the right rack upright using three 10-32 x 5/8-in. screws and three retainer nuts
as shown in Figure 3.
3. Attach the left front bracket to the left rack upright using three 10-32 x 5/8-in. screws and three retainer nuts.
4. Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lbs. (29 cm-kgs).
5 Screw, 10-32 x 5/8-in., panhead Phillips 6 Retainer nut, 10-32
FIGURE 3
Flush Mount Rack Kit Installation Procedure 7 of 10 53-1002127-04
Attaching front brackets to a rack
Attaching rear brackets to a rack
2
5
6
Complete the following steps to attach the rear brackets to the rack.
1. Position the right rear bracket in the right rear of the switch as shown in Figure 4.
2. Attach the brackets to the right rack upright using three 10-32 x 5/8-in. screws and retainer nuts.
3. Repeat step 1 and step 2 to attach the left rear bracket to the left rack upright.
4. Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lbs. (29 cm-kgs).
2 Rear brackets, right (left side similar) 5 Screw, 10-32 x 5/8-in., panhead Phillips 6 Retainer nut, 10-32
FIGURE 4
8 of 10 Flush Mount Rack Kit Installation Procedure
Attaching the rear brackets to a rack
53-1002127-04
Attaching rear brackets to the switch
3
Complete the following steps to attach the rear brackets to the switch.
1. Align the right rear bracket to the right rear of the switch and using two 8-32 x 5/16-in. screws, attach the
bracket to the switch as shown in Figure 5.
2. Align the left rear bracket to the left rear of the switch and using two 8-32 x 5/16-in. screws, attach the bracket
to the switch.
3. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lbs. (17 cm-kgs).
3 Screws, 8-32 x 5/16-in., panhead Phillips
FIGURE 5
Flush Mount Rack Kit Installation Procedure 9 of 10 53-1002127-04
Attaching the rear bracket to the switch
10 of 10 Flush Mount Rack Kit Installation Procedure
53-1002127-04
Loading...