Bosch TES-80521 RW User Manual [ru]

www.bosch-home.com/welcome

TES 803.. / TES 805.. / TES 807..

en Instruction manual fr Mode d’emploi nl Gebruiksaanwijzing pl Instrukcja obsługi cs Návod k použití ru Инструкция по эксплуатации

TES803_805_807_1RW.indb 1 08.05.2013 14:52:50

2827

5a 5b

TES805 TES807

en English 2

fr Français 28

nl Nederlands 54

pl Polski 80

cs Čeština 106

ru Pycckий 131

Included in delivery (see page 4) Contenu de l’emballage (voir page 30) De verpakking bevat (zie pagina 56) Zakres dostawy (patrz strona 82) Rozsah dodávky (na straně 108)

Объем поставки (см. стр. 133)

TES803_805_807_1RW.indb 2 08.05.2013 14:52:53

5a 5b

2827

TES805 TES807

TES803_805_807_1RW.indb 3 08.05.2013 14:52:53

20a

20a 21

D E

10a

10c

10b

10d

23b

23c23a

TES803_805_807_1RW.indb 4 08.05.2013 14:52:56

20a

20a 21

20a

TES803_805_807_1RW.indb 5 08.05.2013 14:52:56

Robert Bosch Hausgeräte GmbH

Dear Coffee Connoisseur,

Contents

Congratulations on purchasing this fully

automatic espresso machine from Bosch.

These operating instructions describe vari-

ous appliance designs, which differ in detail.

Each appliance is assigned an E-number,

e.g. TES803. The E-No. of the respective

appliance can be found on the packaging or rating label 25.

Please also refer to the quick reference

guide. This can be kept in a special storage

compartment 22 until the appliance is used

again.

Safety instructions ......................................3

Included in delivery .....................................4

At a glance..................................................4

Before using for the rst time......................5

Controls ......................................................6

Displays ......................................................8

Display settings ..........................................9

Customising ..............................................10

Child-proof lock......................................... 11

Menu settings ...........................................12

Preparation using coffee beans ................14

Preparation using ground coffee .............15

Preparing milk froth and warm milk .........16

Dispensing hot water ................................17

Maintenance and daily cleaning ...............17

Service Programmes ...............................20

Tips on energy saving ..............................24

Frost protection ........................................24

Storing accessories ..................................24

Accessories ..............................................24

Disposal ....................................................25

Guarantee.................................................25

Technical specications ............................25

Simple troubleshooting .............................26

TES803_805_807_1RW.indb 2 08.05.2013 14:52:57

TES80.. | 04/2013

Safety instructions

Please read through the instructions carefully and proceed accordingly; store in a safe place! This fully automatic espresso machine is designed for the preparation of small amounts of coffee for domestic use or for use in household-like, noncommercial environments. Householdlike environments include staff areas

in shops, ofces, agricultural and other

small businesses or for use by guests at bed-and-breakfast establishments, small hotels and similar residential facilities.

¡ Danger of electric shock!

Connect and operate the appliance only in

accordance with the specications on the rating plate.

Use only if power cord and appliance show

no signs of damage.

In the event of a malfunction, unplug the

appliance immediately.

To avoid potential hazards, repairs such as replacing a damaged cable, must only be carried out by our customer service

personnel.

Do not allow persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, to use this appliance, unless they are being supervised or have been given instruction concerning use of the appliance by a person responsible for their

safety. Keep children away from the appliance.

Children should be supervised to ensure

that they do not play with the appliance.

Please store descaling and cleaning agents

in a safe place, out of reach of children. Do not drink cleaning agents.

¡ Risk of scalding!

The milk frother 10 for milk / hot water

gets

very hot. After use, allow to cool down rst before touching.

¡ Warning!

Adjust the grinding unit only while it is running! Otherwise the appliance may be

damaged. Do not reach into the grinding unit.

Never immerse the appliance or mains

cable in water. Unplug the appliance before cleaning it. Do not use a steam cleaner.

ONLY TES807

¡ Warning!

The cup warmer 27 gets very hot!

Use the appliance indoors and at room

temperature only.

TES803_805_807_1RW.indb 3 08.05.2013 14:52:57

Robert Bosch Hausgeräte GmbH

Included in delivery

(Figure A on the fold-out pages)

1 Fully automatic espresso machine

TES803 / 805 / 807

2 Instruction manual 3 Quick reference guide 4 Milk frother 5 Water hardness testing strip 6 Measuring spoon

At a glance

(Figures B, C, D, E and F on the fold-out pages)

1 Power on/off switch O / I 2 Customising button á 3 Service programmes button à 4 Selection buttons < > 5 Display a) Status line b) Selection line c) Navigation line 6 Rotary knob for display settings 7 Info menu button j 8 start button (drinks / programmes) 9 Coffee outlet,

height-adjustable and swivelling

10 Milk system,

height-adjustable and removable (milk / hot water)

a) Upper part b) Lower part c) Suction hose d) Suction pipe 11 Removable water tank

12 Lid for water tank 13 Storage compartment for

measuring spoon

14 Measuring spoon

(insertion aid for water lter)

15 Bean container

ONLY TES805 / TES807

7 Milk container, insulated

ONLY TES807

8 Water lter

16 Aroma cover 17 Selector for grind setting 18 Powder compartment

(ground coffee / cleaning tablet)

19 Door to brewing unit 20 Brewing unit a) Lock b) Cover 21 Sliding button

22 Storage compartment for quick

reference guide

23 Drip tray a) Panel b) Grate c) Coffee grounds container 24 Cable storage compartment 25 Rating label (E-No.; FD)

ONLY TES805 / TES807 26 Milk container, insulated

ONLY TES807 27 Cup warming function 28 Button for cup warming function,

illuminated

29 Water lter

TES803_805_807_1RW.indb 4 08.05.2013 14:52:57

Before using for the

 rst time

General

Fill the water tank with pure, cold, uncarbonated water only and preferably use only beans or coffee blends suitable for fully auto-

matic espresso and coffee machines. Do

not use coffee beans that have been glazed, caramelised or treated with other additives containing sugar, since they will block the

brewing unit.

The water hardness setting can be adjusted

on this appliance. The factory setting for the

water hardness is 4. Check the hardness of the water you use with the enclosed test

strip. If a value other than water hardness

4 is displayed, change the setting on the appliance accordingly after switching on (see “Menu settings – Water hardness”).

Setting up the appliance

● Place the fully automatic espresso machine on a  at, water-resistant surface that can take its weight.

Important: Only use the appliance in frostfree rooms ported or stored at temperatures below

0 °C, wait at least 3 hours before operation.

● Pull out the mains plug from the cable compartment 24 and plug it in. Adjust the length of the cable by pushing it back in

and pulling it out. To do this, place the appliance with its back  ush with the edge

of the work surface and either pull the cable downwards or push it upwards.

● Lift the lid of the water tank 12.

● Remove and rinse the water tank 11 and

 ll it with fresh, cold water. Do not  ll

above the “max” mark.

● Replace the water tank 11 and push it

 rmly downwards into place.

● Close the water tank lid 12 again.

● Fill the bean container 15 with coffee

beans.

. If the appliance has been trans-

● Press the power switch 1 O / I . The start button 8 lights up and the different

languages appear in the display 5. The following languages can be selected:

TES8.. DE

Deutsch English Français Italiano

TES8.. RW

English Русский Nederlands Français Italiano Svenska Español Polski Українська Magyar Türkçe Dansk Norsk Suomi Português Čeština Ελληνικa

● Use the buttons < and > 4 to select the language in which you want the texts to appear

The selected language is highlighted.

● Press the you selected is saved.

● The brand logo lights up in the display 5. The appliance now heats up and rinses. Some water will run out of the coffee outlet 9.

Sprache Deutsch

English Français

start

button 8. The



display

start

language

TES80.. | 04/2013

TES803_805_807_1RW.indb 5 08.05.2013 14:52:57

Robert Bosch Hausgeräte GmbH

ËË Í

● The appliance is ready for use when the symbols for the drink selection and the start button 8 light up in the display 5.

Espresso

Â Ã À Á Å Æ

Info: The factory settings of the fully automatic espresso machine for optimal

switches off automatically after 1 hour (see “Menu settings – AutoOffafter”).

Note: If the appliance is being used for the

rst time, the

run

ated for a long period, the rst beverage will

not have the full Aroma and should not be

consumed.

When the fully automatic espresso machine

is rst used, you will achieve a suitably thick and stable “crema” only after the rst few cups have been dispensed.

performance. The appliance

service programme has been

, or the appliance has not been oper-

are programmed

Controls

Power on/off switch O / I The power on/off switch 1 O / I is used to

switch the appliance on or off. The appliance

rinses automatically when it is switched on

and off.

The appliance will not rinse if:

● it is still warm when switched on.

● there was no coffee drawn before

switching off.

The appliance is ready for use when the symbols for the drink selection and the start button 8 light up in the display 5.

Customising button á

The appliance provides the option of saving and calling up customised settings for

coffee drinks. Please refer to the section

“ Customising” for information on how to

save and call up these settings.

Service programmes button

Press the à button 3 briey to call up the selection of service programmes. Please run the programme as described in “Service Programmes”.

Press and hold to activate or deactivate the

child-proof lock, see “Child-proof lock”.

Rotary knob

Turn the rotary knob 6 to the left or right to navigate through the display 5, or to adjust

parameters in the menu.

Selection buttons < and >

Press the selection buttons 4 < and > to navigate up and down through the menu levels (navigation line 5c).

TES803_805_807_1RW.indb 6 08.05.2013 14:52:57

TES80.. | 04/2013

ËË Í

Display

The display 5 uses symbols to indicate the selection options, coffee strength and percup quantity, and uses text to indicate set-

tings, ongoing processes and messages.

The rotary knob 4 can be used to change settings selected setting is highlighted by a frame.

Espresso

Â Ã À Á Å Æ

Example: The status line 5a shows the name of the type of drink, along with the strength setting

55 and per-cup quantity

The selection line 5b shows symbols for

drink selection.

The arrows in the navigation line 5c indicate the direction in which more menu levels can

be found.

Please refer to “Displays” for more detailed

information.

Start button Press the start button 8 to begin drink

preparation or to start a service programme.

Press the start button 8 again during drink preparation to stop the dispensing process

prematurely.

6 and selection buttons

. The

j button and settings

Use the j button 7 to display information

(press briey) and adjust settings (hold down for at least 3 seconds).

Displaying information

The following information can be displayed in the Info menu:

● when should the next service be

completed.

● how many drinks have been dispensed since the espresso machine was

switched on.

● Press the j button 7 briey and navigate with the < and > buttons 4.

Info Descale after. 200

Clean after 200 Change filter in 200

Info No. of coffees 11

No. of milk mixes 15 Amount hot water 2l

* appears only if the lter is activated.

Press the j button 7 briey to return to the drink selection. If no button is pressed for about 10 seconds, the appliance automatically switches back to drink selection mode.

À À À

Adjusting settings

See “Menu settings”.

TES803_805_807_1RW.indb 7 08.05.2013 14:52:58

ËË Í

Adjusting the grinding unit The rotary selector 17 adjusts the grind

settings from coarse to  ne.

¡ Warning!

Adjust the grinding unit only while it is running! Otherwise the appliance may be dam-

aged. Do not reach into the grinding unit.

● While the grinding unit is running,

adjust the rotary selector 17 from  ne (a: Turn anticlockwise) to coarse (b: Turn clockwise).

a b

Info: The new setting will not become

apparent until after the second cup of

coffee.

Note: If the message Please adjust

grinding unit to coarser setting!

appears in the display, the grind setting

for the coffee beans is too  ne. Adjust the grinding unit to a coarser setting.

Tip: For dark roast coffee beans, choose a

 ner grind; for lighter beans a coarser grind.

ONLY TES807 Cup warming function

¡ Warning!

The cup warmer 27 gets very hot!

The fully automatic espresso machine has a cup warmer 27 that can be switched on or off manually with button 28. When the cup warmer 27 is on, button 28 lights up.

Tip: For optimal cup warming, place the base of the cups on the cup warmer 27.

Displays

Display messages

Various messages are shown in the display 5.

Information (only TES807)

For example:

Espresso

Water tank

almost empty

Prompts

For example:

Espresso

Refill water tank

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 8 08.05.2013 14:52:58

TES80.. | 04/2013

Ë Í

Display settings

Press the selection buttons < and > 4 to select the following selection menus in the menu levels:

Drink selection

Espresso

Â Ã À Á Å Æ

Coffee strength (only for coffee drinks)

Espresso

Turn the rotary knob 6 to adjust the following parameters within the menus:

Settings – Drink selection:

2xEspresso

2xCoffee

Espresso

Coffee

Caffe Latte (only TES807) Macchiato

Cappuccino

Æ Ç

My coffee (only TES807) Milk froth

Warm milk

Hot water

5 55 555

Per-cup quantity

Espresso

Î Ð Ò

Select your personal per-cup quantity

Espresso

± 0 ml

My coffee (only TES807)

My coffee Espresso Milk

40%

Settings – Coffee strength:

Very mild

Mild

åå

Normal

ååå

Strong

Very strong

aromaDouble Shot strong

aromaDouble Shot:

The longer the coffee is brewed, the more bitter substances and undesired Aromas are released. This has a negative effect on the taste and makes the

coffee less easily digestible. So for extra strong coffee, the TES8.. has a special aromaDouble Shot function. When half

the quantity has been prepared, coffee is ground and brewed again so that only the

pleasant, Aromatic scents are released. The aromaDouble Shot function can be

selected for all coffee drinks except for

EspressoÀ with a small per-cup quantity, 2 x Espresso Â and 2xCoffee Ã.

aromaDouble Shot strong +

ååå

aromaDouble Shot strong ++

TES803_805_807_1RW.indb 9 08.05.2013 14:52:58

Robert Bosch Hausgeräte GmbH

Settings – Per-cup quantity

small

medium

large

Settings – Personal per-cup quantity

The preset per-cup quantity be individually adjusted to the size of the cup in use by turning the rotary knob 6. The per-cup quantity can be adjusted according to the drink selected. An arrow in the Ò symbol in the top right-hand corner of the display indicates whether the per-cup

quantity was increased or decreased. If you

set for example Coffee Á, the adjustment of the per-cup quantity in ml, and in the case of a milk-based coffee drink, for example CappuccinoÆ, the adjustment of the per-cup quantity including the volume of

milk (froth) in ml, is indicated.

Î, Ð

or Ò can

Storing or changing the user

● Hold down the 3 seconds.

The menu appears:

á button 2 for at least

User settings User 1



start User 2 User 3

● Select the required user using the selec-

tion button and press the start button 8.

The following selection appears in the display:

User settings: User 1 Edit name



start Delete name Coffee temp.

Important: The selected amount in ml is an approximate value and can vary sig-

nicantly as a result of crema forming, the grind setting or the type of milk used, etc.

Settings – My coffee (only TES807)

In addition to selecting coffee strength and per-cup quantity, you can choose the exact mix of espresso and milk for your own coffee setting Mycoffee Ç:

● The setting can be dened in 20 % steps

by turning the rotary knob 6.

Customising

You can store up to 6 user proles in the

User settings menu. The required coffee

and hot water temperatures are saved in

the user proles.

Important: The “Customising” settings (á button 2) are not identical to those under “Menu settings” (j button 7) and vice

versa.

● To change the user name, use the selec-

tion button to go to Edit name and press the start button 8.

The input eld appears in the display:



start

â ABCDEFGHIJKLMNOPQ

_ _____

Abort Store

● Turn the rotary knob 6 to select a letter or

number.

● Conrm by pressing the start button 8.

There are 6 characters available for the

user name.

To delete entries made, select the symbol

â and press the start button 8.

Note:

Press the selection button

entry. Press the selection button < to cut the process short.

Info: The entry can be overwritten at any

time.

> to save your

TES803_805_807_1RW.indb 10 08.05.2013 14:52:58

TES80.. | 04/2013

Ë Í

To delete the user, use the selection button

Delete name start and press the start

button 8.

Saving temperatures

● Use the selection button to select Coffee

temp. or Hot water temp..

● Turn the rotary knob 6 to select the

required setting.

● Press the á button 2.

The settings are saved.

● Dispense a drink (see “Preparation using coffee beans”).

● The selected settings are saved.

● Press the á button 2 to exit the

customised menu.

Info: If you wish the appliance to exit the menu automatically, you can set this as described under “Menu settings – Exit

profile”.

AromaIntense (only TES807)

The intense avour of the espresso or coffee may be adapted to individual require-

ments by setting the brewing speed.

● Simply press the selection but-

ton AromaIntense Espresso or

AromaIntense Coffee.

● Finally, use the rotary knob 6 to select

either normal brewing speed, e. g.

Espresso standard or slow brewing

speed e. g. Espresso intensive.

● Press the

The settings are saved.

Calling up a user prole

● Press the

The user prole menu appears:

á button 2.

á button 2 briey.

Select a profile

Robert User 1 User 2

● Turn the rotary knob 6 to select a user prole and press the start button 8.

The drink selection menu appears:

Child-proof lock

The appliance can be locked to protect

children from scalding and burning.

● Hold down the à button 3 for at least

3 seconds.

The display 5 shows a key; the child-proof lock is activated.

Espresso

It is no longer possible to operate the

appliance.

ONLY TES807: The cup warmer 27 is

switched off.

● To deactivate the child-proof lock,

hold down the à button 3 for at least

3 seconds. The key disappears from the display 5.

Macchiato

Robert

● Set the drink, coffee strength, etc. (see “Display settings”).

TES803_805_807_1RW.indb 11 08.05.2013 14:52:59

À Á Å Æ

Robert Bosch Hausgeräte GmbH

Menu settings

● Hold down the j button 7 for at least 3 seconds.

The different setting options are now displayed.

Settings Coffee temp.

Hot water temp. <85°C Exit profile

The different setting options can be selected with the selection buttons < and > 4.

Note: The changes you have made are

saved automatically. It is not necessary to conrm them additionally. If no entry is made after approx. 2 minutes, the menu will close automatically.

The following settings can be selected:

AromaIntense Coffee (only TES807)

The intense avour of the coffee may be

adapted to individual requirements by set-

ting the brewing speed.

● Use the rotary knob 6 to select either

normal brewing speed Coffee standard or slow brewing speed Coffee intensive.

Info: The brewing setting can also be selected for Caffe Latte and MyCoffee.

It makes no change to the warm milk.

Coffee temp.

● Turn the rotary knob 6 to set the coffee

temperature. The setting applies to all

types of preparation, except the custom-

ised settings under “Customising”.

Hot water temp.

● Turn the rotary knob 6 to set the tem-

perature. The setting applies to all types

of preparation except the customised

settings under “Customising”.

Language

● Turn the rotary knob 6 to select the required language.

AromaIntense Espresso (only TES807)

The intense avour of the espresso may be

adapted to individual requirements by set-

ting the brewing speed.

● Use the rotary knob 6 to select either nor- mal brewing speed Espresso standard or slow brewing speed Espresso

intensive.

Info: The brewing setting can also be selected for Cappuccino and Macchiato.

It makes no change to the milk froth.

Exit profile

● Here you can set whether the appliance should exit the customising function automatically automatic or manually

manually.

Auto off after

● Turn the rotary knob 6 to enter the time span after which the appliance should automatically switch off following the last

drink preparation.

A time between 5 minutes and 8 hours can

be set.

Cup warm. off in (only TES807)

Here you can set the time span after which the cup warmer 27 switches off again

automatically.

● Set the required time by turning the rotary knob 6.

TES803_805_807_1RW.indb 12 08.05.2013 14:52:59

Contrast

The display 5 contrast can be set from –10 to

+10. The factory setting is +0.

● Turn the rotary knob 6 to select the

required setting.

Water hardness

● Turn the rotary knob 6 to select the

required water hardness

Info: It is important to set the water hardness correctly, so that the appliance indicates accurately when the descaling pro-

gramme should be run. The factory setting

for the water hardness is

You can check the water hardness using the enclosed test strip or by asking your

local water supplier.

● Dip the test strip brie y in water and check the result after one minute.

Level Water hardness

German (°dH) French (°fH)

1-7

8-14

15-21

22-30

1, 2, 3 or 4.

1-13 14-25

26-38 39-54

Water filter

A new water  lter 29 must be rinsed before it can be used.

● To do this, press the water  lter 29  rmly into the water tank 11 with the aid of the measuring spoon 14. Fill the water tank with water up to the “max” mark.

● Turn the rotary knob 6 to select start and press the start button 8.

Place 1 l container Place suction pipe in container start

● Place a container with a capacity of 1 litre under the milk frother 10.

● Place the end of the suction pipe 10d in

the container.

● Press the start button 8. Water will now  ow through the  lter 29 to rinse it.

● Next, empty the container.

The appliance is ready for use again.

Info: Rinsing the  lter 29 simultaneously activates the setting for the “change  lter” display.

You can  nd detailed information about the water  lter in the enclosed  lter instructions.

The  lter 29 is no longer effective when the

Service - change filter display appears, or

at the latest after two months. It needs to be

replaced for reasons of hygiene and so that there is no build-up of limescale (this could

damage the appliance).

Replacement  lters can be obtained from retailers (TCZ7003) or from customer service (575491).

TES80.. | 04/2013

TES803_805_807_1RW.indb 13 08.05.2013 14:52:59

Robert Bosch Hausgeräte GmbH

Ë Í

If no new lter 29 is used, turn the

Waterfilter setting to no.

Info: If the appliance has not been used for a prolonged period (for example, when you are on vacation), the existing lter 29 should be rinsed before the appliance is

used again. To do this, simply dispense a cup of hot water.

Transport. lock

● To avoid damage caused by frost during transport and storage, the appliance must

be completely emptied rst.

Info: The appliance must be ready for use and the water tank 11 lled.

● Press the start button 8. The appliance automatically empties the pipe system

and switches off.

● Empty the water tank 11 and the drip tray 23.

Preparation using coffee beans

This fully automatic espresso machine grinds beans freshly for each brew. If possible, use only beans for fully automatic

coffee and espresso machines. For optimal

quality, deep-freeze the beans or store in

a cool place in sealed containers. Coffee beans can be ground while frozen.

Important: Fill the water tank 11 with cold,

fresh water every day. The water tank 11 should always contain sufcient water for operating the appliance.

Tip (only TES807): Pre-warm cups, especially the cup warmer 27.

Different coffee drinks can be prepared

quite simply at the press of a button.

small, thick

espresso cups, on

Factory reset

You can cancel your own settings and reset

the factory settings.

● To activate the factory settings, press the

start button 8.

Info: The appliance can also be reset to

the factory settings using a combination of

buttons. The appliance must be switched off fully.

● Hold down the selection buttons < and >

4 and the on/off switch 1 O / I at the same

time for at least 5 seconds. Press the start button 8. The factory settings are now reactivated.

Note: With some settings, the coffee is prepared in two stages (see

“ aromaDouble Shot”). Wait until the procedure is fully completed.

Drink preparation without milk

The appliance must be ready for use.

● Place the pre-warmed cup(s) under the

coffee outlet 9.

● Select the required 2 xEspresso Â,

2xCoffeeÃ, Espresso À or CoffeeÁ

by turning the rotary knob 6.

The display 5 shows the selected drink along with the setting for coffee strength and per-cup quantity for this drink.

Espresso

Â Ã À Á Å Æ

TES803_805_807_1RW.indb 14 08.05.2013 14:52:59

TES80.. | 04/2013

Ë Í

You can change the settings (see “Display settings”) or call up and customise settings

(see “Customising”).

● Press the start button 8.

The coffee is brewed and then dispensed

into the cup(s).

Drink preparation with milk

The appliance must be ready for use.

● Place the suction pipe 10d of the milk frother 10 deep in the milk container 26.

● Swivel the coffee outlet 9 to the right until

it clicks into place.

● Place the pre-warmed cup or glass under the coffee outlet 9 and milk frother 10.

● Select the required Caffe Latte Ä (only

TES807), Macchiato Å, Cappuccino Æ

or Mycoffee Ç (only TES807) by turning the rotary knob 6.

The display 5 shows the selected drink along with the setting for coffee strength and per-cup quantity for this drink.

Preparation using ground coffee

This fully automatic espresso machine can also be operated using ground coffee (not

instant coffee powder).

Note: The aromaDouble Shot function

cannot be used when coffee is prepared

using ground coffee.

Drink preparation without milk

The appliance must be ready for use.

● Place the pre-warmed cup(s) under the

coffee outlet 9.

● Select the required 2 xEspresso Â,

2xCoffeeÃ, Espresso À or CoffeeÁ

by turning the rotary knob 6.

● Open the powder compartment 18.

● Pour in no more than 2 level measuring

spoons 14 of ground coffee.

Cappuccino

À Á Å Æ È É

You can change the settings (see “Display settings”) or call up and customise settings

(see “Customising”).

● Press the start button 8.

First milk is delivered into the cup or glass.

Then the coffee is brewed and dispensed

into the cup or glass.

Important: Dried milk residue is difcult

to remove, so the milk frother 10 must be cleaned with lukewarm water immediately

after use (see “Cleaning the milk system”).

¡ Warning!

Do not use whole beans or instant coffee.

● Close the powder compartment 18.

● Press the start button 8.

The coffee is brewed and then dispensed

into the cup(s).

Note: Repeat the procedure for another cup

of coffee. If coffee is not dispensed within

90 seconds, the brewing chamber emp-

ties automatically to avoid an overow. The appliance rinses.

TES803_805_807_1RW.indb 15 08.05.2013 14:52:59

Robert Bosch Hausgeräte GmbH

Drink preparation with milk

The appliance must be ready for use.

● Place the suction pipe 10d of the milk frother 10 deep in the milk container 26.

● Swivel the coffee outlet 9 to the right until

it clicks into place.

● Place the pre-warmed cup or glass under the coffee outlet 9 and milk frother 10.

● Select the required Caffe Latte Ä (only

TES807), Macchiato Å, Cappuccino Æ

or Mycoffee Ç (only TES807) by turning the rotary knob 6.

● Open the powder compartment 18.

● Pour in no more than 2 level measuring spoons 14 of ground coffee.

¡ Warning!

Do not use whole beans or instant coffee.

● Close the powder compartment 18.

● Press the start button 8.

First milk is delivered into the cup or glass.

Then the coffee is brewed and dispensed

into the cup or glass.

Important: Dried milk residue is difcult

to remove, so the milk frother 10 must be cleaned with lukewarm water immediately

after use (see “Cleaning the milk system”).

Note: Repeat the procedure for another

cup of coffee / milk drink. If coffee is not

dispensed within 90 seconds, the brewing chamber empties automatically to avoid an

overow. The appliance rinses.

Preparing milk froth and warm milk

¡ Risk of burns!

The milk frother 10 gets very hot. After use, allow to cool down rst before touching.

The appliance must be ready for use.

● Place the suction pipe 10d of the milk frother 10 deep in the milk container 26.

● Place the pre-warmed cup or glass under the outlet of the milk frother 10.

● Select the required setting Milk froth È or Warmmilk É by turning the rotary knob 6.

● Press the start button 8.

Milk froth or warm milk ows from the outlet

of the milk frother 10.

Press the start button 8 again to cut the

process short.

Info: When preparing warm milk, you may

hear a whistling sound. This is caused by

the milk frother 10 for technical reasons.

Tip: For optimal milk froth quality, use cold

milk with a fat content of at least 1.5 % if possible.

Important: Dried milk residue is difcult

to remove, so the milk frother 10 must be cleaned with lukewarm water immediately

after use (see “Cleaning the milk system”).

TES803_805_807_1RW.indb 16 08.05.2013 14:52:59

Dispensing hot water

¡ Risk of burns!

The milk frother 10 gets very hot. After use, allow to cool down  rst before touching.

The appliance must be ready for use.

● Place the pre-warmed cup or glass under

the outlet of the milk frother 10.

● Select the required setting for Hot

water

● Press the start button 8.

Please remove suction hose start

● Remove the milk suction hose 10c and press the start button 8.

Hot water runs out of the milk frother outlet 10.

Press the start button 8 again to cut the

process short.

Note: It is possible to set the temperature of

the hot water (see “Menu settings”).

by turning the rotary knob 6.

Maintenance and daily cleaning

¡ Danger of electric shock!

Unplug the appliance before cleaning it. Never submerse the appliance in water. Do not use a steam cleaner.

● Wipe the outside of the appliance with a soft, damp cloth.

● Do not use any cleaning agents that contain alcohol or spirits.

● Do not use abrasive cloths or cleaning agents.

● Always remove any limescale, coffee, milk, cleaning or descaling  uid residue immediately. Such residue can cause corrosion. New sponge cloths may contain salts. Salts can cause rust  lm on stain-

less steel and must therefore be washed

out thoroughly before use.

● Pull the drip tray 23 with the coffee grounds container 23c forwards and out. Remove the panel 23a and grate 23b. Empty and clean the drip tray and coffee

grounds container.

Do not put the following items in the

dishwasher: Panel of drip tray 23a, powder compartment 18, brewing unit 20, water tank 11, Aroma cover 16 and

stainless steel milk container.

The following parts may be cleaned

in the dishwasher: Drip tray 23, grate 23b, coffee grounds container 23c, measuring spoon 14 and the individual

parts of the milk container cover.

TES80.. | 04/2013

TES803_805_807_1RW.indb 17 08.05.2013 14:53:00

● Remove powder compartment 18 and

rinse under running water.

● Wipe out the inside of the tray holders.

Important: Drip tray 23 and coffee grounds container 23c should be emptied and cleaned daily to prevent mould from

developing.

Note: If the appliance is cold when switched on, or if it is switched off after

dispensing coffee, it rinses automatically. In other words, the system cleans itself.

Important: If the appliance has not been

used for a prolonged period of time (e. g.

after a vacation), clean the entire

appliance

thoroughly, including the milk system 10 and brewing unit 20.

Cleaning the milk system Important: The milk system 10 must be cleaned immediately after use!

The milk system 10 can be pre-cleaned

automatically (see “Service programmes” or cleaned manually.

Dismantling the milk system 10 for cleaning:

● Pull the milk system 10 forward out of the

appliance.

● Turn the upper part 10a in an anti- clockwise direction and remove from the lower part 10b.

● Clean the individual parts with detergent

solution and a soft cloth.

● Rinse all parts with clean water and dry.

Robert Bosch Hausgeräte GmbH

TES803_805_807_1RW.indb 18 08.05.2013 14:53:01

● Put all the parts back together. The milk frother can then be clicked back into

place in the appliance.

Info: All parts of the milk frother 10 can also

be put in the dishwasher.

Cleaning the brewing unit (Fig. F)

(refer also to the quick reference guide) In addition to the automatic cleaning programme, the brewing unit 20 should be

removed regularly for cleaning.

● Switch the appliance off completely at the power on/off switch 1 O / I ; no buttons

are lit.

● Take hold of the door to the brewing unit 19 at the bottom and open it.

● Slide the red lock 20a on the brewing unit 20 completely to the left.

● Press the red button 21, grasp the brew- ing unit 20 by the recessed grips and

remove carefully.

● Remove the cover 20b of the brewing unit and rinse the brewing unit 20 thoroughly

under running water.

● Thoroughly clean the brewing unit sieve under the running water.

Important: Clean the brewing unit without detergent and do not put it in the

dishwasher.

● Wipe out the inside of the appliance thoroughly with a damp cloth and remove

any coffee residues.

● Allow the brewing unit 20 and the inside of the appliance to dry.

● Replace the cover 20b on the brewing unit and reinsert the brewing unit 20 fully

into the appliance.

● Slide the red lock 20a fully to the right and close the door 19.

TES80.. | 04/2013

TES803_805_807_1RW.indb 19 08.05.2013 14:53:02

Robert Bosch Hausgeräte GmbH

Service Programmes

Tip: Refer also to the quick reference guide

in the storage compartment 22.

At regular intervals, the display 5 shows the following texts:

Short rinse milk system or Service - Descale or Service - Clean or Service - Calc‘nClean.

The appliance should be cleaned or descaled immediately using the corresponding pro-

gramme. You have the option of combining

the processes Descaling and Cleaning with the Calc‘nClean function (see

“ Calc‘nClean”). If the service programme is

not run as instructed, the appliance may be

damaged.

¡ Warning!

Follow the instructions for using the descaling

and cleaning agents for each service

programme.

programme! Do not drink the liquids! Never use vinegar, vinegar-based products, citric acid or citric acid-based products! Never put descaling tablets or other descaling agents in the powder compartment 18!

Before starting the respective service programme (descaling, cleaning or Calc‘nClean), remove the brewing unit,

clean as instructed and replace.

Never interrupt the service

Specially developed and suitable descaling and cleaning tablets are available from retailers or customer service.

Accessories Ordering number

Retail Customer

service

Cleaning tablets

Descaling tablets

Cleaning the milk system

Duration: approx. 1 minute

TCZ6001 310575

TCZ6002 310967

Cleaning and service Short rinse



milk system

start

Calc‘nClean

The milk system 10 can be pre-cleaned

automatically.

● Press the à button 3.

Short rinse milk system start

● Press the start button 8.

Place glass under frother, place suction pipe in glass start

● Place an empty glass under the milk system 10 and put the end of the pipe

10d in the glass.

● Press the start button 8. The milk system is cleaned automatically.

● Now empty the glass and clean the suction pipe 10d.

In addition to this, clean the milk system thoroughly at regular intervals (by hand or

in the dishwasher).

TES803_805_807_1RW.indb 20 08.05.2013 14:53:02

TES80.. | 04/2013

Descaling

Duration: approx. 30 minutes.

Cleaning and service



Descale

start

Clean

The

start

button 8 ashes while the different

descaling processes are running. The gures on the top right indicate the progress of the programme.

Important: If there is a water lter 29 in the

water tank 11, it needs to be removed

before the service programme is run.

● Press the à button 3.

Descale start

● Press the start button 8; the display 5 will

guide you through the programme.

Add 0.5 l water and descaler start

● Pour lukewarm water into the empty water tank

11 up to the “0.5 l” mark and then

dissolve two Bosch descaling tablets in it.

● Press the start button 8. The descaling programme will now run for about

20 minutes.

Descaling

Not enough descaling fluid. Refill fluid start

Info: If there is not enough descaling solution in the prompt is displayed. Pour in descaling solution

water tank 11, the corresponding

and press the start button 8 again.

Clean and refill water tank start

● Rinse the water tank 11 and rell it with fresh

water up to the “max” mark.

● Press the start button 8. The descaling

programme now runs for about 1 minute and rinses the appliance.

Descaling

Empty drip tray Replace drip tray

● Empty the drip tray 23 and reinsert it.

Place 1 l container Place suction pipe in container start

● Place a container with 1 litre capacity

the milk frother 10.

● Place the end of the suction pipe 10d in

the container.

● Press the start button 8.

under

Remove filter start

Info: If the water lter 29 is activated, the display will prompt you to remove the lter 29, then press the start button 8 again.

Empty drip tray Replace drip tray

● Empty the drip tray 23 and reinsert it.

Replace the lter if one is being used. The appliance is ready for use again.

Important: Wipe down the appliance using a soft, damp cloth to immediately

remove any descaler residue. Such residue can cause corrosion. New sponge cloths may contain salts. Salts can cause rust lm on stainless steel and must therefore be washed out thoroughly before use.

Thoroughly clean the suction pipe 10d of

the milk frother.

TES803_805_807_1RW.indb 21 08.05.2013 14:53:02

Robert Bosch Hausgeräte GmbH

Cleaning

Duration: approx. 8 minutes.

Cleaning and service Descale



Clean

The start button 8 ashes while the different cleaning processes are running. The gures

on the top right indicate the progress of the

programme.

● Fill the water tank 11 up to the “max”

mark.

● Press the à button 3.

Clean start

● Press the start button 8; the display 5 will

guide you through the programme.

start

Empty drip tray Replace drip tray

● Empty the drip tray 23 and reinsert it.

The appliance is ready for use again.

Calc‘nClean

Duration: approx. 36 minutes.

Calc‘nClean combines the separate functions of descaling and cleaning. If both programmes are due to be run soon, the espresso machine automatically suggests this service programme.

Cleaning and service Short rinse

milk system



Calc‘nClean

start

Empty drip tray Replace drip tray

● Empty the drip tray 23 and reinsert it.

The appliance rinses twice.

Position swivel arm

● Swivel the coffee outlet 9 to the left until it

clicks into place.

Cleaning

Open powder compartment

● Open the powder compartment 18.

Insert Bosch cleaning tablet and close drawer

● Drop a Bosch cleaning tablet into the

drawer 18 and close it.

Press start

● Press the start button 8. The clean-

ing programme will now run for about

7 minutes.

Cleaning

The

start button 8 ashes while the different

Calc‘nClean processes are running. The gures on the top right indicate the progress of the programme.

Important: If there is a water lter 29 in the

water tank 11, it needs to be removed

before the service programme is run.

● Press the à button 3.

Calc‘nClean start

● Press the start button 8; the display 5 will guide you through the programme.

Empty drip tray Replace drip tray

● Empty the drip tray 23 and reinsert it.

● Swivel the coffee outlet 9 to the right until

it clicks into place.

TES803_805_807_1RW.indb 22 08.05.2013 14:53:02

TES80.. | 04/2013

Place 1 l container Place suction pipe in container start

● Place a container with a capacity of at

least 1 l under the milk frother 10.

● Place the end of the suction pipe 10d in

the container.

● Press the start button 8. The appliance

rinses twice.

Cleaning

Open powder compartment

● Open the powder compartment 18.

Insert Bosch cleaning tablet and close drawer

● Drop a Bosch cleaning tablet in the

drawer 18 and close.

Remove filter start

Info: If the water lter 29 is activated, the display will prompt you to remove the lter 29, then press the start button 8 again.

Add 0.5 l water and descaler start

● Pour lukewarm water into the empty water

tank 11 up to the “0.5 l” mark and then

dissolve two Bosch descaling tablets in it.

● Press the start button 8. The descaling

programme now runs for about

20 minutes.

Descaling

Not enough descaling fluid. Refill fluid start

Info: If there is not enough descaling solution in the water tank 11, the corresponding prompt is displayed. Pour in descaling solution and press the start button 8 again.

Clean and refill water tank



start

● Rinse the water tank 11 and rell it with fresh water up to the “max” mark.

● Press the start button 8. The descaling pro-

gramme now runs for about 1 minute more,

followed by the cleaning programme for

about 7 minutes, and rinses the appliance.

Descaling Cleaning

Empty drip tray Replace drip tray

● Empty the drip tray 23 and reinsert it.

Replace the lter if one is being used. The

appliance has completed descaling and

cleaning and is ready for use again.

Important: Wipe down the appliance using a soft, damp cloth to immediately remove any

descaler residue. Such residue can cause corrosion. New sponge cloths may contain salts. Salts can cause rust lm on stainless

steel and must therefore be washed out

thoroughly before use.

Thoroughly clean the suction pipe 10d of

the milk frother.

Note: If one of the service programmes is

interrupted, e. g. by a power outage, proceed as follows:

● Rinse the water tank 11 and rell it with fresh

water up to the “max” mark.

● Press the start button 8. The cleaning programme now runs for about 3 minutes,

and rinses the appliance.

Cleaning

Empty drip tray Replace drip tray

● Empty the drip tray 23 and reinsert it.

The appliance is ready for use again.

TES803_805_807_1RW.indb 23 08.05.2013 14:53:03

Robert Bosch Hausgeräte GmbH

Tips on energy saving

Storing accessories

● The display has a dimming function that switches on automatically when the

appliance is not in use. The display is illuminated dimly. Press any button or

the rotary knob to brighten the display

illumination again.

● If the appliance is not being used, switch it off at the power on/off switch 1 O / I on

the front.

● If possible, do not interrupt coffee or milk froth dispensing. Stopping a process

prematurely results in higher energy

consumption and the drip tray lls up more quickly.

● Descale the appliance regularly to avoid a build-up of limescale. Limescale residue results in higher energy consumption.

Frost protection

¡ To avoid damage caused by frost

during transport and storage, the appliance must be completely emp-

tied rst.

See “Menu settings – Transport. lock.”

The espresso machine has special compartments for storing the accessories and

quick reference guide inside the appliance.

● To store the measuring spoon 14, remove the water tank 11 and insert the spoon in the shaped recess 13.

● To store the quick reference guide, open the door to the brewing unit 19 and stow away the quick reference guide in the storage compartment 22 provided for this

purpose.

Accessories

The following accessories are available from retailers or from customer service:

Accessories Ordering number

Retail Customer

service Cleaning tablets TCZ6001 310575 Descaling tablets TCZ6002 310967

Water lter TCZ7003 575491

Care set TCZ7004 570351 Milk container with

“Fresh Lock” lid

TCZ8009 576165

TES803_805_807_1RW.indb 24 08.05.2013 14:53:03

TES80.. | 04/2013

Disposal

Guarantee

Dispose of packaging in an environmen-

tally-friendly manner. This appliance is

labelled in accordance with European Direc-

tive 2012/19/EG concerning used electrical

and electronic appliances (waste electrical

and electronic equipment – WEEE). The

guideline determines the framework for the return and recycling of used appliances as

applicable throughout the EU. Please ask

your specialist retailer about current dis-

posal facilities.

The guarantee conditions for this appliance

are as dened by our representative in the country in which it is sold. Details regarding

these conditions can be obtained from the dealer from whom the appliance was pur-

chased. The bill of sale or receipt must be

produced when making any claim under the

terms of this guarantee.

Changes reserved.

Technical specications

Power connection (voltage/frequency) 220-240 V / 50-60 Hz Heater wattage 1600 W Maximum static pump pressure 19 bar

Maximum water tank capacity (without lter) 2.4 l

Maximum capacity of the coffee bean container ~300 g Length of power cable 100 cm Dimensions (H x W x D) 385 x 301 x 458 mm Weight, empty 10–12 kg Type of grinding unit Ceramic

TES803_805_807_1RW.indb 25 08.05.2013 14:53:03

Robert Bosch Hausgeräte GmbH

Simple troubleshooting

Problem Cause Solution

Display shows

Refillbeancontainer

although the bean container 15 is full, or the grinding unit does not

grind the beans. No tea water dispensed. The milk frother 10 or its

Too little or no milk froth, or the milk frother 10 does

not draw the milk in.

The selected per-cup

quantity is not reached.

Coffee dispensing slows to a trickle or stops

completely. Coffee has no “crema”. Unsuitable type of coffee. Use a type of coffee with a

Coffee is too “acidic”. The grinding setting is too

Coffee is too “bitter”. The grind setting is too ne

If you are unable to solve the problem, always call the hotline.

You will nd the telephone numbers at the back of these instructions.

Beans are not falling into the grinding unit (beans too

oily).

holder is soiled.

The milk frother 10 or its

holder is soiled.

Milk unsuitable for frothing. Use low-fat milk (1.5 % fat).

The milk frother 10 is not

correctly assembled.

Build-up of limescale in the

appliance.

Coffee is ground too nely.

Pre-ground coffee is too

ne.

Build-up of limescale in the

appliance.

The beans are no longer

fresh.

The grinding setting is not

suitable for the beans.

coarse or the pre-ground

coffee is too coarse. Unsuitable type of coffee. Use a darker roast.

or the pre-ground coffee is too ne.

Unsuitable type of coffee. Change the type of coffee.

Gently tap the bean container 15. Change the type of coffee if

necessary. When the bean

container

with a dry cloth.

Clean the milk frother 10 or its holder (see “Cleaning the milk

system”).

Clean the milk frother 10 or its holder (see “Cleaning the milk

system”).

Moisten and assemble the milk

frother parts.

Descale the appliance using two descaling tablets, if necessary

repeat the procedure.

Adjust the grinding unit to a

coarser setting. Use coarser preground coffee.

Descale the appliance.

higher proportion of robusta

beans. Use fresh beans.

Adjust the grinding setting to

ne. Adjust the grinding unit to a ner

setting or use ner pre-ground coffee.

Adjust the grinding unit to a coarser setting or use coarser

pre-ground coffee.

15 is empty, wipe it

TES803_805_807_1RW.indb 26 08.05.2013 14:53:03

+ 138 hidden pages