Bosch D7212GV3 Specsheet

Intrusion Alarm Systems | D7212GV3 Control Panel

D7212GV3 Control Panel

www.boschsecurity.com

u Fully integrated intrusion and fire functions allow

users to interface with one system instead of two

u Conettix IP‑based communication options provide

high‑speed, secure alarm transport and control
through connection of up to two wired (DX4020)
and/or wireless (ITS‑DX4020‑G) network interfaces

The D7212GV3 Control Panel delivers a powerful new
solution for intrusion (commercial and residential) and
residential fire alarm system applications. Monitor
alarm points for intruder or fire alarms while operating
user command centers and other outputs. The
D7212GV3 Control Panel includes a communicator
that sends event reports to selected public switched
telephone network (PSTN), IP network, or general
packet radio service (GPRS) destinations through four
programmable route groups. Program all system
functions locally or remotely (attended or unattended)
through Remote Programming Software (RPS);
program critical parameters on site through a keypad.
The D7212GV3 Control Panel provides up to 40
individually identified points. Each point
accommodates normally-open and normally-closed
devices with end-of-line (EOL) resistor supervision.
Each point is programmable for fire, fire supervisory,
or intrusion applications.

Functions

Programmable Outputs

• 2 A alarm power at 12 VDC

• 1.4 A auxiliary power at 12 VDC

• Four alarm output patterns

u Four programmable areas with perimeter and

interior partitioning

u 40 points with flexible configuration options to meet

application specific requirements

u Commercial Wireless allows up to 32 RF points

• Automatic bell test

• Three on-board outputs, 24 off-board programmable
outputs

System Response

• High performance micro‑controller provides industry
leading system response

• 31 custom point indexes, including fire supervisory

• Selectable point response time

• Cross point capability

• Fire alarm verification

• Watch mode

• Scheduled events (skeds) arm, disarm, bypass and
unbypass points, control relays, and control authority
levels

Area Configurations

Area programming offers a wide selection of different
system configurations. Each area is assigned an
account number to define annunciation, control, and
reporting functions. Multiple areas can be linked to a
shared area which is automatically controlled (hallway
or lobby). Area arming can be conditional on other
areas (master or associate). Any area can be
configured for perimeter and interior arming, not
requiring a separate are for this function.

| D7212GV3 Control Panel

2

User Interface

• Supervises up to eight command centers (up to 32
non-supervised command centers can be used)

• Custom keypad text is fully programmable, including
remote programming

• Four custom functions

• Full function command menu including custom
functions

• Each user has authority by area and 16-character
name

• 14 custom authority levels control user’s authority to
change, add, delete passcodes, delete access control
tokens, delete cards, disarm, bypass points, and
initiate system tests

• Up to 40 programmable, scheduled events and up to
16 event functions for controlling relays, enabling
passcodes and windows, and automatically arming
and disarming areas

• Adjustable brightness or volume for command center
display or sounder

• One parallel printer

The D7212GV3 provides on-premises point and system
status annunciation. The fully selectable user interface
customizes command center displays and allows users
to create appropriate menu items and functions.
Function lists can help a user become familiar with the
operation of the control panel and custom functions
allow users to perform complex functions with a few
keystrokes. Each function can be programmed and
identified by sixteen characters of custom text and can
contain up to 32 keystrokes.

Notice

At least one command center per system is
recommended.

Two Man Rule

Two Man Rule requires two unique passcodes on the
same command center to disarm an area. Without the
second passcode, the system denies entry. Two Man
Rule requires the presence of two people at opening,
providing added security.

Early Ambush

Early Ambush requires two passcode entries on the
same command center. Enter the same passcode
twice or have two unique passcodes, depending on
the configuration. The first entry disarms the area and
the second entry stops a timer programmed to send a
duress event. If the second entry does not occur
within the programmed time, the system generates a
duress event. Early Ambush allows users to inspect the
premises and use the system to confirm that the area
is safe to enter, providing added security.

Easy Exit Control

The D7212GV3 Control Panel changes from one armed
state to another armed state without disarming. For
example, if you change the state from Master Arm to

Perimeter Arm, the control panel complies and reports
the change. Easy Exit Control reduces the number of
keystrokes, simplifying system operation.

Programmable Passcode-controlled Menu List

The system prompts users to enter a passcode prior to
viewing the command center menu. The command
center display shows the user the menu options
allowed according to the user’s authority level.
Passcode-controlled menus provide users only with
the options and information pertinent to them,
simplifying system operation.

Passcode Follows Scope

Use Passcode Follows Scope to restrict passcode
arming and disarming only to the command center's
immediate local area, even if the command center can
report events from other areas. Passcode Follows
Scope simplifies the arming and disarming procedure
without limiting any other command center command
capabilities.

Passcodes

User passcodes contain three to six digits. Assign each
user one of 14 customized authority levels in each
area. Restrict passcodes to operate only during certain
times.
The Two Man Rule and Early Ambush options require
two passcodes, providing additional security in
financial establishments such as banks.

Communications

The D7212GV3 prioritizes and sends reports to four
route groups. Each group has a programmable primary
and backup destination.
The D7212GV3 provides flexible communications for
most central stations with reporting capabilities such
as:

• Individual point numbers

• Opening or closing reports by user and area number

• Remote programming attempts

• Diagnostic reports

The D7212GV3 uses the DX4020 Ethernet Network
Interface Module and/or the ITS‑DX4020‑G GPRS/GSM
Communicator to communicate with the Conettix
D6600 and D6100i Communications Receiver/
Gateways. Using Conettix IP communication offers a
secure path that includes anti-replay/anti-substitution
features and provides enhanced security with
encryption. Both the DX4020 and ITS‑DX4020‑G can
be used for remote programming.

Security and Fire Detection

The D7212GV3 Control Panel provides eight on-board
points, and up to 32 additional off-board points
(depending on model and expansion interfaces). You
can program individual points to monitor all types of
burglar alarms, fire alarms, and supervision devices.

Commercial Wireless

The Commercial Wireless platform, powered by
Inovonics wireless mesh network technology, ensures
superior range, reliability, and scalability for

3 | D7212GV3 Control Panel

commercial applications. Using a wide range of
transmitters and repeaters, this proven technology
provides flexibility and performance to meet the most
stringent requirements. This exclusive protocol is
available only on Commercial Wireless products.
The Commercial Wireless platform sends redundant
information on several multi-frequency channels within
the FCC Part 15 900 MHz band, providing superior
range and reliability. In comparison, systems that use a
single frequency technology can only send information
on one narrow band channel. Any interference within
the band can cause missed signals. With wireless
registration, it is easy to add this technology to any
application.

Event Log

The event log stores up to 1,000 local and transmitted
events. The event log includes time, date, event, area,
point, and user number. View the event log from select
command centers or remotely retrieve event
information using RPS. RPS operators can retrieve
events periodically using one phone call, rather than
receiving several calls each day. When the event log
reaches a programmed threshold of stored events, it
can send an optional report to a receiver.

Scheduled Events (Skeds)

The internal clock and calendar start individually
scheduled events (skeds). Skeds perform functions
such as arm or disarm, relay control, or point
bypassing. The D7212GV3 Control Panel offers:

• 40 scheduled events with up to 16 different functions
available

• Eight opening windows and eight closing windows

• Eight user windows

• Day-of-week, date-of-month, or holiday only schedules

• Four holiday schedules of 366 days each (leap year)

Fire Test

When a user activates Fire Test Mode, the control
panel suppresses all reports to the central station. The
command center and annunciator show all testing
data. An automatic sensor reset feature saves time;
you do not need to reset the sensors manually. At the
end of test, the command center shows the number of
untested points.

Programming, Diagnostics and Controls

Installers can do limited programming on-site with a
keypad (critical parameters; such as, .Account IDs,
Central Station and RPS IP addresses and phone
numbers, reporting formats, and such).They can also
do full programming on-site or remotely (attended or
unattended) with RPS. A programmable system
passcode prevents unauthorized remote programming.
D7212GV3 Control Panels accommodate up to four
separate destinations for primary, alternate, and
backup receivers for automatic test reports.
When resetting alarms or arming or disarming a
system, the user is identified by name and number.

ROM Updates

An on‑site flash update key provides for easy feature
enhancements without replacing ROM chips.

Certifications and approvals

FCC Designed to comply with Part 15

Region Certification

USA UL AMCX: Central Station Alarm Units (AN-

SI/UL 1610 and 1635); AMTB: Control
Panels, SIA False Alarm Reduction (UL
864 and ANSI/SIA CP-01-2000); AOTX:
Local Alarm Units (ANSI/UL 609 and AN­SI/UL 464); APAW: Police Station Alarm
Units (ANSI/UL 365 and ANSI/UL 464);
APOU: Proprietary Alarm Units (ANSI/UL

1076); NBSX: Household Burglar Alarm
System Units (ANSI/UL 1023); UTOU:
Control Units and Accessories, House­hold System Type (ANSI/UL 985)

CSFM see our website

Installation/configuration notes

Compatible Products

Keypads

D1260 Series Keypads
(D1260, D1260W, D1260R, D1260BLK, D1260B)

D720 Series Keypads
(D720, D720W, D720R, D720B)

D1255 Series Keypads
(D1255, D1255W, D1255B)

D1265 Touch Screen Keypad

D279A Independent Zone Control

Detectors

D278S Four-wire Addressable Detector Base

D285/TH Photoelectric Smoke Detector Heads

D298S Addressable Detector Base

D7050 Series Addressable Photoelectric Smoke and Smoke Heat
Detector Heads

F220-B6PM/S Addressable Detector Bases with POPITs

MX775i Addressable PIR Detector

MX794i Long Range Multiplex PIR Detector

MX934i Addressable PIR Detector

MX938i Addressable PIR Detector

ZX776Z PIR Detector

ZX794Z Long Range PIR Detector

ZX835 TriTech Microwave/PIR Detector

ZX935Z PIR Detector

ZX938Z PIR Detector

4 | D7212GV3 Control Panel

ZX970 PIR/Microwave Detector

Bosch conventional detectors, including Blue Line, seismic, PIR, TriTech
PIR Microwave, photoelectric, heat, and smoke.

Enclosures

D8103 Universal Enclosure

D8108A Attack-Resistant Enclosure

D8109 Fire Enclosure

Magnetic Contacts

Bosch magnetic contacts include recessed, terminal connection,
miniature, overhead door, and surface mount.

Modules

Conettix ITS‑DX4020‑G GPRS/GSM Integrated Communicator

Conettix DX4020 Network Interface Module

Conettix DX4010V2 USB/Serial Interface Module

Conettix C900V2 Dialer Capture Module

D113 Battery Lead Supervision Module

D125B Dual Class B Initiating Module

D127 Reversing Relay Module

D129 Class A Initiating Module

D130 Auxiliary Relay Module

D185 Reverse Polarity Signaling Module

D192G Notification Appliance Circuit Module

D928 Phone Line Switcher

D5060 MUX Programmer

D8125 POPEX Point Expander

D8128D OctoPOPIT Eight Point Expander

D8125MUX Point Expander

D8125INV Wireless Interface Module

D8129 Octo-relay Module

D8130 Door Release Module

D9127 Series POPIT Modules

D9131A Parallel Printer Interface Module

DS7432 Eight-input Remote Module

DS7457i Series Single Zone Multiplex Input Modules

DS7460i Two-input Module

DS7461i Single-input Multiplex Module

DS7465i Input and Output Module

Communications Formats

Modem IIIa

2

Contact ID

Programming

Remote Programming Software (RPS)

Commercial Wireless Products

ISW‑D8125CW Commercial Wireless Interface

ISW‑EN7280 Serial Receiver

ISW‑EN4200 Serial Receiver

ISW‑EN4204R LED Receiver

ISW‑EN4216R LCD Receiver

ISW‑EN4016SK Survey Receiver

ISW‑EN5040‑T High‑power Repeater

ISW‑EN1210 Universal Transmitter (Single‑input)

ISW‑EN1210EOL Universal Transmitter with EOL Resistor

ISW‑EN1210SK Survey Transmitter

ISW‑EN1210W Door‑Window Transmitter with Reed Switch

ISW‑EN1215EOL Universal Transmitter with Wall Tamper and EOL
Resistor

ISW‑EN1215WEOL Door‑Window Transmitter with Wall Tamper, Reed
Switch, and EOL Resistor

ISW‑EN1223D Water‑resistant Pendant
Transmitter (Double‑button)

ISW‑EN1223S Water‑resistant Pendant Transmitter (Single‑button)

ISW‑EN1223SK Survey Pendant Transmitter

ISW‑EN1233D Necklace Pendant Transmitter (Double‑button)

ISW‑EN1233S Necklace Pendant Transmitter (Single‑button)

ISW‑EN1235D Beltclip Pendant Transmitter (Double‑button)

ISW‑EN1235S Beltclip Pendant Transmitter (Single‑button)

ISW‑EN1235DF Fixed‑location Transmitter (Double‑button)

ISW‑EN1235SF Fixed‑location Transmitter (Double‑button)

ISW‑EN1242 Smoke Detector‑Transmitter

ISW‑EN1247 Glassbreak Sensor‑Transmitter

ISW‑EN1249 Billtrap Transmitter

ISW‑EN1260 PIR Motion Sensor Transmitter (Commercial and High‑end
Domestic Applications)

ISW‑EN1261HT PIR Motion Sensor Transmitter (High‑traffic Areas)

ISW‑EN1262 PIR Motion Sensor Transmitter (Residential and
Low‑traffic Commercial Applications)

ISW‑EN1265 PIR Motion Sensor Transmitter (Ceiling‑mount
Applications)

5 | D7212GV3 Control Panel

Parts included

Quant. Component

1 D7212GV3 Board

1 Mounting Skirt

1 Faceplate with D7212GV3 Label

1 Literature pack

1 Literature CD containing all product literature

Kits

Components -K1 -K1W

D7212GV3 Board 1 1

D101 Lock and Key Set 1 1

D1255 Keypad 1

D1255W Keypad 1

D1260 Keypad

D1640 Transformer 1 1

D8103 Enclosure 1 1

DS835i PIR Detector 2 2

Kits

Components -K6 -K7

D7212GV3 Board 1 1

D101 Lock and Key Set 1 1

D1255 Keypad 1

D1255W Keypad

D1260 Keypad 1

D1640 Transformer 1 1

D8103 Enclosure 1 1

DS835i PIR Detector 1

D8128D OctoPOPIT Eight‑point Expander 1

Conettix DX4020 Ethernet Network Interface
Module

• Installation Instructions

• Owners Manual

• Release Notes

1

Technical specifications

Communications

SDI Bus A (+): 9 VDC

SDI Bus B (-): 9 VDC

4572 m (15,000 ft)

4572 m (15,000 ft)

Electrical

Current Draw (Minimum): 200 mA

Current Draw (Maximum): 500 mA

Output (Alarm): 2 A at 12 VDC

Output (Auxiliary, Continuous
Power, and Switched Auxiliary
combined):

Voltage (Operating): 12 VDC

Voltage (AC): 16.5 VAC 40 VA plug-in

Voltage (DC): • Up to 2 12 VDC, 7 Ah

1.4 A at 10.2 VDC to 13.9 VDC

transformer (D1640)

sealed lead acid
rechargeable batteries

• Up to 2 12 VDC, 18 Ah
sealed lead acid
rechargeable batteries

Environmental

Relative Humidity: 5% to 85% at +30°C (+86°F),

Temperature (Operating): 0°C to +50°C (+32°F to +120°F)

non-condensing

Number of…

Areas: 4

Custom Functions: 4

Programmable Relay Outputs: 27

Events: Store up to 1,000

Parallel Printers: 1

Passcode Users: 99, plus 1 service passcode

Points: 40 (eight on-board, up to 32

RF Points: 32

SKEDs: 40

off‑board)

Trademarks

Trademark names are used throughout this document.
In most cases, these designations are claimed as
trademarks or registered trademarks in one or more
countries by their respective owners. Rather than
placing a trademark symbol in every occurrence of a
trademark name, Bosch Security Systems, Inc. uses
the names only in an editorial fashion and to the
benefit of the trademark owner with no intention of
infringing the trademark.

Inovonics is a trademark of Inovonics Wireless Corporation.

Telephone Connection: RJ31X or RJ38X

6 | D7212GV3 Control Panel

Ordering information

D7212GV3 Control Panel

Includes one printed circuit board (PCB) with
mounting skirt and faceplate with label, and a
literature pack and CD.

Order number D7212GV3

D7212GV3K1 Burglar Kit with D1255

Contains one PCB, one lock and key set, one
transformer, one universal enclosure, two PIR
detectors, and one D1255 Keypad.

Order number D7212GV3K1

D7212GV3K1W Burglar Kit with D1255W

Contains one PCB, one lock and key set, one
transformer, one universal enclosure, two PIR
detectors, and one D1255W Keypad.

Order number D7212GV3K1W

D7212GV3K6 Burglar Kit with D1260

Contains one PCB, one lock and key set, one
transformer, one universal enclosure, one D1260
Keypad, and one Conettix DX4020 Ethernet Network
Interface Module.

Order number D7212GV3K6

D7212GV3K7 Burglar Kit with D8128D

Contains one PCB, one lock and key set, one
transformer, one universal enclosure, one D1255
Keypad, one PIR detector, and one OctoPOPIT eight­point expander.

Order number D7212GV3K7

Accessories

ICP-SDI-9114 SDI Splitter

Provides the ability to set up two independent SDI
buses from a single SDI connection on the control
panel.

Order number ICP-SDI-9114

ICP‑EZTS Dual Tamper Switch

Combination tamper switch with a wire loop for
additional tamper outputs.

Order number ICP-EZTS

D101 Lock and Key Set

Short-body lock set with one key supplied. Uses the
D102 (#1358) replacement key.

Order number D101

D122 Dual Battery Harness

Harness with circuit breaker. Connects two batteries
to a compatible control panel.

Order number D122

D122L Dual Battery Harness with Long Leads

Color-coded harness with circuit breaker and leads
measuring 89 cm (35 in.). Connects 12 V batteries to
compatible control panels.

Order number D122L

D126 Standby Battery (12 V, 7 Ah)

A rechargeable sealed lead‑acid power supply used as
a secondary power supply or in auxiliary or ancillary
functions.

Order number D126

D1218 Battery (12 V, 18 Ah)

A 12 V sealed lead‑acid battery for standby and
auxiliary power with two bolt‑fastened terminals.
Includes hardware for attaching battery leads or spade
connectors

Order number D1218

D1224 Battery (12 V, 26‑28 Ah)

A 12 V sealed lead‑acid battery for standby and
auxiliary power with two bolt‑fastened terminals.
Includes hardware for attaching battery leads or spade
connectors.

Order number D1224

D136 Plug‑In Relay

Maximum rating is 1 A at 24 VDC or 2 A at 12 VDC.
Available individually (D136) or in a package of 25
(D136‑25).

Order number D136

D137 Mounting Bracket

Used to mount accessory modules in D8103, D8108A,
and D8109 enclosures.

Order number D137

D138 Mounting Bracket, Right Angle

Used to mount accessory modules in D8103, D8108A,
and D8109 enclosures.

Order number D138

D1640 Transformer

System transformer rated at 16.5 VAC, 40 VA.

Order number D1640

D8103 Enclosure

Grey steel enclosure measuring 41 cm x 41 cm x 9 cm
(16 in. x 16 in. x 3.5 in.).

Order number D8103

D8108A Attack Resistant Enclosure

Grey steel enclosure measuring 41 cm x 41 cm x 9 cm
(16 in. x 16 in. x 3.5 in.). UL Listed. Includes lock and
key set. B520, B4512, and B5512 require the B12
mounting plate.

Order number D8108A

D9002‑5 Mounting Skirt

Mounts inside D8103, D8108A, and D8109 enclosures.
Can accept up to six standard 7.62 cm x 12.7 cm (3 in.
x 5 in.) cards.

Order number D9002-5

7 | D7212GV3 Control Panel

Represented by:

Americas: Europe, Middle East, Africa: Asia-Pacific: China: America Latina:

Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: [phone]
Fax: [phone]
[e-mail]
www.boschsecurity.us

Bosch Security Systems B.V.
P.O. Box 80002
5617 BA Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: [phone]
[e-mail]
www.boschsecurity.com

Robert Bosch (SEA) Pte Ltd, Security
Systems
11 Bishan Street 21
Singapore 573943
Phone: [phone]
Fax: [phone]
[e-mail]
www.boschsecurity.asia

Bosch (Shanghai) Security Systems Ltd.
201 Building, No. 333 Fuquan Road
North IBP
Changning District, Shanghai
200335 China
Phone [phone]
Fax: [phone]
www.boschsecurity.com.cn

Robert Bosch Ltda Security Systems Division
Via Anhanguera, Km 98
CEP 13065-900
Campinas, Sao Paulo, Brazil
Phone: [phone]
Fax: [phone]
[e-mail]
www.boschsecurity.com

© Bosch Security Systems 2014 | Data subject to change without notice
2492184715 | en, V2, 05. Nov 2014

Software Options

RPS Kit (USB)

Account management and control panel programming
software with USB security key (dongle).

Order number D5500C-USB