Bosch B46, B465-MR-1640 Installation Guide

1 | Overview

The B46 External Annunciator is an optional module that uses audio and LEDs to show System Trouble, Power, and Battery status through a knockout on select enclosure doors.

BOSCH

Figure 1.1: B46 overview

Callout ― Description Callout ― Description

1 ― Sounder 4 ―

2 ― SYSTEM TROUBLE LED 5 ―

3 ―

POWER LED

BATTERY LED

B46 to B465 connection

2 | Remove enclosure knockouts

Remove all designated knockouts prior to installing the B46. Perform the following to remove the enclosure knockouts:

1. Strike the four corners of the enclosure door knockout using a slotted screw driver.

2. Use a punchout tool to remove the 3-hole pattern knockouts on the enclosure side wall. Refer to Figure 2.1 for knockouts.

Figure 3.1: Installing into an enclosure

Callout ― Description Callout ― Description

1 ― B46 2 ―

Enclosure

4 | Wire the B46 to a module

Plug in the B46 cable between the B46 and B465 module. Make sure to insert the cable with the black portion of the cable towards the back of the port. Inserting the B46 wiring into a supported module:

1. Insert one end of the B46 cable into the B46 port.

2. Insert the other end of the B46 cable into the supporting module’s port. Refer to Figure 4.1.

USB

TRBL

PNL LINE 2

TX RX

BAT

ANNUNC

EXTERNAL

TMPR

Figure 4.1: Wiring the B46 to a module (B465 shown)

Callout ― Description Callout ― Description

1 ― Module (B465 shown) 3 ― B46 module

2 ― B46 module cable (included)

Figure 2.1: Removing enclosure knockouts

Callout ― Description Callout ― Description

1 ― B46 LED cover knockout 3 ― B46 3-hole pattern knock-

out

3 | Install into an enclosure

Installing the B46 into an enclosure:

1. Insert the 3 supplied screws into the exterior, upper-right side of the enclosure. Refer to Figure 3.1.

2. Secure the screws to the mounting bracket.

3. Insert the lock set into the enclosure door knockout.

4. Insert the plastic LED cover into the enclosure door. Refer to Figure 2.1 for the B46 LED cover knockout location.

5 | Certiﬁcations

Region Certiﬁcation

US UL 365 - Police Station Connected Burglar Alarm

Units and Systems

UL 609 - Local Burglar Alarm Units and Systems

UL 636 - Holdup Alarm Units and Systems

UL 864 - Controls and Accessories for Fire Alarm Systems

UL 985 - Household Fire Warning System Units

UL 1023 - Household Burglar-Alarm System Units

UL 1076 - Proprietary Burglar Alarm Units and Systems

UL 1610 - Central Station Burglar Alarm Units

UL 1635 - Digital Alarm Communicator System Units

FCC Part 15 Class B

Fire Department of New York (FDNY) - Certiﬁed

6 | Certiﬁcations

Region

Certiﬁcation

CAN/ULC S303 - Local Burglar Alarm Units and Systems

CAN/ULC S304 - Signal Receiving Centre and Premise Alarm Control Units

ULC S545 - Residential Fire Warning System Control Units

ULC-ORD C1023 - Household Burglar Alarm System Units

ULC-ORD C1076 - Proprietary Burglar Alarm Units and Systems

ICES-003 - Digital Apparatus

6 | Speciﬁcations

Dimensions 5.5 in x 4.1 in x 1.7 in (140 mm x 105 mm x 44 mm)

Voltage (operating) 12 VDC nominal

Current Standby or Alarm: 23 mA

Compatible enclosure

Relitive humidity Up to 93% non-condensing

Temperature (operating)

Static may cause temporary loss of communication when using any one of the above enclosures.

B10/B10R Medium Control Panel Enclosure D8103 Universal Enclosure (requires B12 mounting plate)

0° to +49° C (+32° to 120° F)

Trademarks

All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.

Bosch Security Systems, Inc. product manufacturing dates

Use the serial number located on the product label and refer to the Bosch Security Systems, Inc. website at http://www.boschsecurity.com/datecodes/.

Bosch Security Systems, Inc.

130 Perinton Parkway Fairport, NY 14450 USA

www.boschsecurity.com

Bosch Sicherheitssysteme GmbH

Robert-Bosch-Ring 5 85630 Grasbrunn

Germany

F.01U.312.441 | 02 | 2015.05

External Annunciator

B46

en Installation Guide