Bosch B4512, B5512 Installation Guide

Quick Start Guide

B5512/B4512/B3512

Communication Devices

Control Panel

Transformer

18 VAC

BATTERY

OUTPUT A

umper Under Cover

AUX PWR

COM

OUTPUT A

AUX

- 12V +

SLOT 2

SDI2

Device Bu

R Y G B

1 COM 2

SLOT

COMMU

NICATION M

ON-BOARD POINTS

Open 3.7 - 5.0 VD

Normal 2.0 - 3.0 VDC

Short 0.0 - 1.3 VDC

1 k

End of Line Resistor

3 COM

COM

ODULE 1

7 COM 8

100

BASE-T

LINK

OUTPUT

USB

ETHERNET

Technology

Location

Ethernet 3On-board 7.5

Cellular

Telephone

B44x Plug-in

B430 Plug-in

USB On-board 3.3.8

= PC direct, connect using AutoIP (Wi-Fi off, wait 2 min)

= PC direct, connect using Male A to Male A USB (B99)

= ‘E’ panel variants do not include on-board Ethernet

ISRG

8.2

Reporting

Personal Notiﬁ cations

Remote RPS Programming

Local RPS Programming

Remote Security App

Control Panel Mounting Locations

B10 Enclosure

B11 Enclosure

Attaching Mounting Clips

Need more help? For detailed instructions, refer to the control panels Installation and System Reference Guide (ISRG) chapter number (ISRG #5.2 ) included on the CD provided with the control panel.

Maximum # of Devices

SDI2 Device Type Options

Device Type Part # Description ISRG # B5512 B4512 B3512 Address Notes

Keypad

B915 2-line Basic 9.1.1

B920 2-line, LCD 9.1.2

B921C/W 2-line, Capacitive 9.1.3

8* 8* 4* 01...08

B930 5-line, ATM LCD 9.1.4

B942 Touch Screen 9.1.5

I/O Expander

B208 8-input 13.1 4 2 0

B308 8-output 11.1 5 3 0

RF Receiver

B810 Bosch RADION 14.1

1* 1* 1* 1

B820 Inovonics 14.2

Power Supply

Remote Cellular

B520 12V DC, 2A 6.3 4 2 2 01...04

B450 B44x Plug-in Interface 8.4 1 1 1 1

SDI2 Speciﬁ cations

• Unshielded, 4 conductor, 22-12 gauge cable

• Maximum cable length 1000’ single run, 7500’ system total

• Allows a combination of home run, daisy chain and T-tapping wiring conﬁ gurations

01...08

Similar device types must use different addresses.

Different device types may use the same address.

* Maximum number of keypads and RF receivers in a single system.

On-board Inputs and Outputs

Terminal Description Speciﬁ cation

18VAC

+ BAT - Battery 12VDC 7Ah

NO C NC Output A(1) Switched AUX, COM, or Dry

COM AUX Aux Power 12VDC, 800mA

R Y G B SDI2 Bus

1 COM 2 Alarm Inputs 1k

TMPR Tamper Optional tamper switch

B C

RESET Reset Switch

MODULE 1 Plug-in Communication module options

Transformer 18VAC 22VA Plug-in

Earth Ground Cold water pipe, or similar

Keypads, SDI2 devices, terminal and Quickconnect in parallel

Ω EOL

Outputs B(2), C(3)

Open collector, 50mA, active low

Hold 5 seconds to enter or exit service mode

Heartbeat

Slow=normal, Rapid=service mode

RPS Programming

Remote Programming Software (RPS)

• Windows based account management and control panel programming application

• Each control panel program is represented as an RPS database record

RPS Features

• Full control panel conﬁ guration; local and remote

• Control panel ﬁ rmware updates; local and remote

• Control panel history event management and reports

• Enhanced remote panel diagnostics

Creating B Series Accounts

1. Panel List > New.

2. Select a B Series control panel.

3. Enter the account information in the ﬁ elds.

Keypad Programming

B930 ATM Style Alphanumeric Keypad Features:

• Bright ﬁ ve-line display

• Four ATM style soft-keys on both sides of the display

Service Mode

• Service Mode differs from Installer Mode by:

• Stopping all reporting

• Enabling a service keypad (address 0,0)

• Rebooting control panel when mode is exited

• Entering Service Mode:

1. Hold the control panel’s RESET button for 5 seconds (Heartbeat LED pulses rapidly).

2. Press [1][2][3][ENTER].

• Exiting Service Mode: Hold the control panel’s RESET button for 5 seconds (Heartbeat LED stops and the control panel reboots).

RPS Ordering Information

• D5500CU: RPS Account management and control panel programming software on CD-ROM

• D5370-USB: USB Security Block (Dongle) Security accessory required for RPS to control panel communications

• D5500C-USB: RPS software and required USB Security Block (Dongle) kit

USB Security Block

RPS Software Download: http://tiny.cc/boschrps

Note: RPS version 5.17 or higher is required for connection to B Series control panels.

RPS Installation and Initial Login

• Install RPS on a Windows computer

• Login to RPS using the following credentials

• User Name: admin

• Password: default

• Change the password after initial login

RPS Help Press F1 for context sensitive help from any window or programming ﬁ eld within the RPS

application.

B Series Control Panel Conﬁ guration

1. To open, double-click the B Series account.

2. Complete the required basic control panel parameters.

Connecting to B Series Control Panels

1. Plug in the Security Block.

2. Click the Connect button.

3. Select the connection method.

4. Connect to the control panel.

5. Send All programming parameters to the control panel.

B920 Series Two-line Alphanumeric Keypad Features:

• Bright two line display

• Eight dedicated function keys

B Series Keypad Functions

• System operation (User)

• System diagnostics (Installer)

• Basic Panel Programming (Installer)

Installer Mode

• Installer Mode provides basic programming and diagnostics at system keypads.

• Installer Mode tools include:

• Programming

• Wireless

• Network

• Service Bypass

• Versions

• Cellular

• Enter Installer Mode by entering the default installer passcode: [1][2][3][ENTER].

• Exit Installer Mode by pressing [ESC].

Keypad Programming Programming needed to make a system operational includes reporting and point programming.

Point Programming Process

1. Enter the Points Menu.

2. Select a Point Number.

3. Set the Point Source.

4. Assign a Point Index.

Point Source: Identiﬁ es the source (device type) of the point being programmed.

If the source selected is Wireless an RFID option is presented. Wireless RFID numbers are found on the wireless device being added.

Point Index: Device (point) behavior characteristics assigned to each point in the system.

Twenty Point Indexes are provided including the following common device functions: 4 – Smoke Detectors 7 – Perimeter Door/Window, no Entry 8 – Perimeter Entry/Exit Door 13 – Interior Motion Detector

Important Notes:

• Change the default ([1][2][3]) installer passcode

• Test system via Main Menu > Actions > Test menu

• Central Station receiver update is required when using Conettix IP and Modem4 reporting format

Need help? Press the keypad HELP key.

2014.03

F01U298167–05