Bosch B450 User Manual
1
2
7
5
6
3
4
8
9
Intrusion Alarm Systems | B450 Conettix Plug-in Communicator Interfaces
B450 Conettix Plug-in Communicator
Interfaces
www.boschsecurity.com
u Full two-way IP communication using Plug-in
Cellular Communicators
The Conettix Plug-in Communicator Interface is a fourwire powered SDI2, SDI, or option bus device that
provides two-way communication with compatible
control panels over commercial cellular networks
using a plug-in communicator (available separately).
System overview
Conettix Plug-in Communicator Interfaces (B450/
B450-M) work with plug-in communicators for primary
or backup alarm communication, remote programming,
and other remote applications. The plug-in
communicator interface supports Conettix IP protocol
with full authentication, 256-bit AES encryption, and
resistance to Denial of Service attacks. The interface
also supports compatible Bosch control panels with
SIA DC-09, CSV-IP. The interface is a reliable way to
add cellular network communications to existing or
new commercial security and fire installations.
u Plug and Play installation makes future radio
technology changes easy
u Compatible with new and most deployed Bosch
control panels
u Supports remote installation of cellular modules for
improved signal
Callout ￚ Description Callout ￚ Description
1 ￚ Compatible control panel 6 ￚ Cellular carrier network
2 ￚ Panel data bus (SDI2, SDI, or
7 ￚ Internet/LAN/WAN
option)
3 ￚ Module 8 ￚ Remote Programming
workstation
4 ￚ USB connection for module
configuration
5 ￚ B44x plug-in communicator
(available separately)
9 ￚ Compatible IP receiver
(Bosch D6100IPv6 shown)
| B450 Conettix Plug-in Communicator Interfaces
2
Functions
Conettix IP communication
The following features are supported with the plug-in
communicator interface via BOSCH Conettix IP
protocol and SIA DC-09 UDP, CSV-IP on supported
control panels including:
• IP Alarm communication
• Remote programing
• Personal notification via text or email on supported
panels
Addressing
Use the address switch to easily assign a bus address
or setup for USB or SMS configuration where required.
Easy configuration
For most installations, the default plug-in
communicator interface settings allow installation with
no device programming required. An address switch
allows easy bus address selection.
For customized network settings, the interfaces
support a USB configuration menu, or configuration via
SMS. The following control panels support RPS
programming:
• B9512G/B9512G-E
• B8512G/B8512G-E
• B6512
• B5512/B5512E
• B4512/B4512E
• B3512/B3512E
• D9412GV4/D7412GV4/D7212GV4
LEDs
Three LEDs provide status and troubleshooting
information.
LED Indication
Heartbeat Plug-in communicator and control panel connection
status
RX An inbound packet is received on the bus
TX An outbound packet is transmitted on the bus
Certifications and approvals
Notice
The B450-M has received certifications only as
noted. If not noted, the certification applies to the
B450 only.
Region Regulatory compliance/quality marks
Europe CE EMC, LVD, RoHS
EN50131EN-ST-000245 EN-
ST-000245_B450_B450M_442_443_2021_04_25
Belgium INCERT B450 + B442
INCERT ANPI-ID-0004-0001 ANPI-
ID-0004-0001-2
Region Regulatory compliance/quality marks
USA UL UL 365 - Police Station Connected Bur-
UL UL 636 - Holdup Alarm Units and Sys-
UL UL 1023 - Household Burglar Alarm Sys-
UL UL 1076 - Proprietary Burglar Alarm
UL UL 1610 - Central Station Burglar Alarm
UL UL 985 - Household Fire Warning Sys-
UL UL 864 - Standard for Control Units and
CSFM California State Fire Marshal
FCC Part 15 Class B
FDNYCoA
FDNYCoA
Canada ULC CAN/ULC S303 - Local Burglar Alarm
ULC CAN/ULC S304 - Standard for Signal Re-
ULC CAN/ULC S545 - Residential Fire Warn-
ULC ULC-ORD C1023 - Household Burglar
ULC ULC-ORD C1076 - Proprietary Burglar
IC ICES-003 - Information Technology
Brazil ANATEL 2708-14-1855
glar Alarm Units
tems
tem Units
Units and Systems
Units
tem Units (6th edition)
Accessories for Fire Alarm Systems
(10th edition)
6286 D7412GV4 D9412GV4 NYC COA
6286 2018-2021
6196
Units and Systems
ceiving Center and Premise Burglar
Alarm
ing System Control Units
Alarm System Units
Alarm Units and Systems
Equipment (ITE)
Installation/configuration notes
Mounting considerations
Install in a location with acceptable wireless network
signal strength. Mount the module into the interior of
a compatible enclosure. Use the 3-hole mounting
pattern. Use the supplied mounting screws.
Wiring considerations
The interface connects to a control panel using a data
bus connection via the module’s terminal strip, or the
module’s interconnect wiring connectors.
For data bus powered installations outside the
compatible control panel enclosure, follow the
maximum wiring distances in the technical
specifications.
Compatibilities
Loading...