SPINWAVE
_______________
USER GUIDE
2039 SERIES
™
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR SPINWAVE™.
When using an electrical appliance, basic precautions should be observed, including the following:
» Use only BISSELL cleaning
products intended for use
with this appliance to prevent
internal component damage.
» Do not immerse. Use only on hard
floor surfaces moistened by the
cleaning process.
» Keep appliance on a level surface.
» Do not carry the appliance while in
use.
WARNING
To Reduce The Risk Of Injury From Moving
Parts – Unplug Before Servicing.
WARNING
Risk Of Injury. Mop Pads May Start
Unexpectedly. Unplug Before Cleaning or
Servicing.
WARNING
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY:
» Connect to a properly grounded
outlet only. See grounding
instructions. Do not modify the
3-prong grounded plug.
» Do not leave appliance when it is
plugged in. Unplug from outlet when
not in use and before servicing.
» Use indoors only.
» Do not allow to be used as a toy.
Close attention is necessary when
used by or near children.
» Do not use for any purpose other
than described in this User’s
Guide. Use only manufacturer’s
recommended attachments.
» Do not use with damaged cord or
plug. If appliance is not working
as it should, or has been dropped,
damaged, left outdoors, or
dropped into water, have it repaired
at an authorized service center.
» Do not pull or carry by cord, use
cord as a handle, close a door on
cord, or pull cord around sharp
edges or corners. Do not run
appliance over cord. Keep cord
away from heated surfaces.
» Do not unplug by pulling on cord.
To unplug, grasp the plug, not the
cord.
» Do not handle plug or appliance
with wet hands.
» Keep hair, loose clothing, fingers,
and all parts of body away from
openings and moving parts.
» Turn off all controls before
plugging or unplugging appliance.
» Use extra care when cleaning on
stairs.
» Do not use appliance in an
enclosed space filled with vapors
given off by oil base paint, paint
thinner, some moth proofing
substances, flammable dust, or
other explosive or toxic vapors.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE
This model is for household use only. Commercial use of this unit voids the manufacturer’s warranty.
WARNING
Improper connection of the equipment-grounding conductor can
result in a risk of electrical shock. Check with a qualified electrician
or service person if you aren’t sure if the outlet is properly grounded.
DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper
outlet installed by a qualified electrician. This appliance is designed
for use on a nominal 120-volt circuit, and has a grounding attachment
plug that looks like the plug in the illustration. Make certain that the
appliance is connected to an outlet having the same configuration as
the plug. No plug adapter should be used with this appliance.
www.BISSELL.com
2
GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded wiring system. If it
should malfunction or break down, grounding provides a safe path
of least resistance for electrical current, reducing the risk of electrical
shock. The cord for this
appliance has an equipment-grounding
conductor and a grounding plug. It must
only be plugged into an outlet that is
properly installed and grounded in
accordance with all local codes and ordinances.
Grounded
Outlets
Grounding Pin
Thanks for buying a BISSELL SpinWave™
We love to clean and we’re excited to share one of our innovative
products with you. We want to make sure your hard surface floor
cleaner works as well as it does today for years to come, so this guide
has tips on using (pages 6-8), maintaining (pages 9), and if there is a
problem, troubleshooting (page 10).
What’s In The Box?
Handle
NOTE: Standard accessories may vary by model. To identify what should be included with
your purchase, please refer to the “Carton Contents” list located on the carton top flap.
Body of
Unit
(2) Soft Touch
Pads
Safety Instructions...........2
Product View................4
Assembly ...................5
Operations ................6-8
Maintenance & Care .........9
(2) Scrubby
Pads
(2) 8oz BISSELL
Multi-Surface Formula
Troubleshooting ............10
Warranty ....................11
Service ......................11
Product Registration........12
Consumer Care.............12
www.BISSELL.com
3
Getting to Know Your SpinWave™
1
7
2
3
4
6
1 Handle
2 Digital Controls
3 Clean Water Tank
4 Low Profile Foot
5 Power Spin Pads
8
9
5
6 Spray Nozzle
7 In-Use Cord Clip
8 Quick Release™ Cord Wrap
9 Lower Cord Wrap
www.BISSELL.com
4
Assembly
WARNING
Do not plug in your SpinWave™ until you are familiar with all instructions
and operating procedures.
Your BISSELL SpinWave™ machine comes in two easy-to-assemble components and does
not require any tools to assemble.
1
Insert handle
into body of
unit until you
hear a click.
NOTE: To easily unwrap the cord for use, just turn the Quick Release™ Cord Wrap
downward to remove the cord from the cord wrap.
click
2
Then, wrap the cord around the Quick
Release™ Cord Wrap and the Lower Cord
Wrap. Your assembly is now complete!
Cleaning Formulas
WARNING
To reduce the risk of fire and electric shock due to internal component damage, use only
BISSELL cleaning fluids intended for use with the hard floor device.
Keep plenty of SpinWave™
formulas on hand so you can clean
your sealed hard floors whenever
it fits your schedule.
Always use SpinWave™ formulas in
your machine. Other solutions may
harm the machine and may void
the warranty.
SPINWAVE™ FORMULAS
Multi-Surface Formula Wood Floor Formula
Great for cleaning ALL
sealed hard floors
Restore your sealed wood
floors’ natural shine
www.BISSELL.com
5
Attaching Mop Pads
Your BISSELL SpinWave™ may have come
with two different mop pads:
(2) Scrubby Pads(2) Soft Touch Pads
1
Your SpinWave™
may have come
with mop pads
attached. If not,
to attach mop
pads, carefully lay
machine down on
the floor.
The Soft Touch Pad is best for
everyday use on delicate flooring like
sealed hardwoods and laminate.
The Scrubby Pad is best used to
power through tough, sticky messes.
2
The back of the mop pad
has a small dot in the
center of the pad.
NOTE: These next steps are to help you apply the mop pads more accurately
onto the machine.
3
First, fold the pad in half,
making sure the cloth
material is inside the fold.
5
Lastly, line up the edge of
the mop pad with the inner
ring on the foot, attaching
the mop pad to the hook
and loop material on the
bottom of the foot.
www.BISSELL.com
6
4
Then, with the mop
pad folded, line up the
small dot in the center
of the pad with the
middle screw on the
bottom of the foot.
Filling Your Clean Water Tank
1
Clean
Water
Tank
The clean water tank is located
on the front of the machine.
4
For large area cleaning
a. Fill formula tank with warm tap water
to the second water fill line.
b. Then add BISSELL® SpinWave™
formula to the second formula fill line.
2
Lift the clean water tank
straight up to remove
from the machine.
For small area cleaning
a. Fill formula tank with warm tap water
to the first water fill line.
b. Then add BISSELL® SpinWave™
formula to the first formula fill line.
3
Unscrew the cap from
the clean water tank.
The clean water tank
has two measuring
volumes depending
on the amount of
space you would like
to clean.
5
Screw the cap
back onto the
clean water tank.
6
Slide the clean water
tank back into place
until you hear a click.
A few notes about filling the clean water tank:
• Fill with warm (140°F/60°C MAX) tap water and add the appropriate
BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER
OR TANK IN MICROWAVE.
www.BISSELL.com
7
Cleaning Your Sealed Hard Floors
ATTENTION: This machine is designed to be used only on sealed hard floors and should not be
used on carpet or rugs. For best cleaning results, sweep or vacuum the floor surface prior to
using the BISSELL SpinWave™. This is to avoid scratching or damaging floors from sharp debris.
1
Plug machine into a
properly grounded
outlet.
TIP: You may feel a slight vibration when turning on the machine if the mop pads are
not aligned correctly. Wait a few seconds for the pads to adjust themselves. If this
doesn’t occur, turn the machine OFF and replace mop pads following the instructions
in “Attaching Mop Pads” section.
4
TIP: For optimum cleaning, perform overlapping cleaning strokes while dispensing
cleaning solution. Care should be taken to not over wet the floor surface, especially
when cleaning wood and other delicate floor surfaces.
To clean,
push the
SPRAY
button to
dispense
solution.
2
Press the ON/OFF
button to start cleaning
your sealed hard floors.
5
3
Solution will spray
out of the nozzle on
the front of the foot.
You should hear a
soft buzzing noise
each time you press
the SPRAY button
to indicate solution
being dispensed.
Recline
the body
of the unit
backward
to start the
rotating
mop pads.
TIP: When cleaning near baseboards, edges, or furniture you may feel a slight pull
from the unit due to bouncing off the surface.
6
For more difficult and stuck on messes, spray solution directly on mess and line
up one of the mop pads parallel to the mess. Move mop pad over mess and slowly
move machine back and forth to clean, continuing to spray solution as needed.
NOTE: When finished cleaning, make sure to push the OFF button before standing the
machine upright as the mop pads will continue to spin until the machine is turned OFF.
www.BISSELL.com
8
Cleaning Your SpinWave
™
WARNING
To reduce the risk of fire, electric shock or injury, turn power OFF and disconnect plug from
electrical outlet before performing maintenance or troubleshooting.
WARNING
Do not set the machine on carpet, rug, or other fabric surface when mop pad is removed as
hook and loop material on foot may damage them.
WARNING
Do not store machine on wet mop pads as they may damage wood or other delicate floors.
1
Turn machine OFF
and unplug the
machine from the
grounded outlet.
2
To remove mop pads,
simply pull pads off the
hook and loop material
on the bottom of the
machine.
4
Wrap cord around the Quick Release™
Cord Wrap and the Lower Cord Wrap.
Clip molded plug to power cord.
3
Machine wash separately in warm
water. Use only liquid detergents.
Do not use bleach or fabric
softener. Tumble dry on low. Do
not iron. Do not dryclean.
5
Store upright in a dry
protected area until the
next use. Since this product
uses water, it must not be
stored where there is danger
of freezing. Freezing will
damage internal components
and may void the warranty.
Store with dry mop pads.
Wet mop pads may damage
wood and other delicate,
sealed hard floors.
NOTE: Any solution remaining in the clean water tank should be emptied prior to
machine storage.
NOTE: Store cleaner in a protected, dry area. Since this product uses water, it must
not be stored where there is danger of freezing. Freezing may damage internal
components and void the warranty.
www.BISSELL.com
9
Troubleshooting
WARNING
To reduce the risk of electric shock, turn power switch o and disconnect plug from
electrical outlet before performing maintenance or troubleshooting checks.
Problem Possible causes Remedies
Unit is
vibrating/
wobbling
Cord is in
way when
cleaning
Reduced
spray OR
no spray
Spin plates
are not
turning or are
wobbling
No power
Machine is
leaking
Mop pads are not aligned with foot
Cord is not clipped in in-use cord
clip
Clean water tank may be empty
Clean water tank may not be
seated completely
System isn’t completely primed Hold trigger for 10 to 15 seconds to
Not holding trigger to spray
solution
Spray tips on foot clogged Turn power OFF; Use a pin to clean
Mop pads are not installed
properly
Machine is standing upright Recline machine
Cord damage While unplugged, inspect the full
Handle not properly in place Remove handle and click back into
Outlet not working Test outlet with a small appliance like
Fuse/breaker outlet blown Reset the breaker
Cap of clean water tank is not
closed properly
Realign the mop pads on the foot
Clip the cord in in-use cord clip
Refill tank
Turn power OFF; Remove and
reseat tank
make sure the solution has flowed to
the spray tips
Hold trigger continuously while
using the machine
the spray tip located front and
center of the machine.
Turn Power OFF; Unplug machine
and follow instructions on page 6 for
replacing mop pads
length of the cord for damage and
refer to a qualified technician if there
is damage
body; To remove handle:
1. Hold base of machine with your
foot, then insert screwdriver into
the slot beneath the cord wrap to
disengage handle tab from body
2. Use other hand to hold metal pole
and pull upward to take handle off
3. To click handle back into body, see
page 5
a cell phone charger, and use another
outlet if needed
Remove the clean water tank and
re-apply the cap
www.BISSELL.com
10
Warranty
This warranty gives you specific legal rights,
and you may also have other rights which
may vary from state to state. If you need
additional instruction regarding this warranty or have questions regarding what it may
cover, please contact BISSELL Consumer
Care by E-mail, telephone, or regular mail
as described below.
Limited Two-Year Warranty
Subject to the *EXCEPTIONS AND
EXCLUSIONS identified below, upon receipt
of the product BISSELL will repair or replace
(with new or remanufactured components
or products), at BISSELL’s option, free of
charge from the date of purchase by the
original purchaser, for two years any
defective or malfunctioning part.
See information below on "If your BISSELL
product should require service".
This warranty applies to product used for
personal, and not commercial or rental
service. This warranty does not apply to
fans or routine maintenance components
such as filters, belts, or brushes. Damage or
malfunction caused by negligence, abuse,
neglect, unauthorized repair, or any other
use not in accordance with the User's Guide
is not covered.
BISSELL IS NOT LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY
NATURE ASSOCIATED WITH THE USE OF
THIS PRODUCT. BISSELL’S LIABILITY WILL
NOT EXCEED THE PURCHASE PRICE OF
THE PRODUCT.
Some states do not allow the exclusion or
limitation of incidental or consequential
damages, so the above limitation or
exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM
THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND
IN LIEU OF ANY OTHER WARRANTIES
EITHER ORAL OR WRITTEN. ANY IMPLIED
WARRANTIES WHICH MAY ARISE
BY OPERATION OF LAW, INCLUDING
THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED
TO THE TWO YEAR DURATION FROM
THE DATE OF PURCHASE AS DESCRIBED
ABOVE.
Some states do not allow limitations on
how long an implied warranty lasts so the
above limitation may not apply to you.
NOTE: Please keep your original sales receipt. It provides proof of date of
purchase in the event of a warranty claim.
Service
If your BISSELL product should require service:
Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about
your warranty, contact BISSELL Consumer Care.
Website:
www.BISSELL.com/service-centers
E-mail:
www.BISSELL.com/email-us
Please do not return this product to the store.
Other maintenance or service not included in the manual should be
performed by an authorized service representative.
For any questions or concerns, BISSELL is happy to be of service.
Contact us directly at 1-800-237-7691.
Call:
BISSELL Consumer Care
1-800-237-7691
Monday – Friday 8am - 10pm ET
Saturday 9am - 8pm ET
Sunday 10am - 7pm ET
www.BISSELL.com
11
Register your product today!
Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:
BISSELL Rewards Points
Automatically earn points for
discounts and free shipping on
future purchases.
Faster Service
Supplying your information now
saves you time should you need to
contact us with questions regarding
your product.
Product Support Reminders
and Alerts
We’ll contact you with any
important product maintenance
reminders and alerts.
Special Promotions
Optional: Register your email
to receive notice of offers,
contests, cleaning tips and more!
Visit www.BISSELL.com/registration!
Visit us online at: BISSELL.com
When contacting BISSELL, have model number of
cleaner available.
Please record your
Model Number: ___________________________
Please record your
Purchase Date: ___________________________
NOTE: Please keep your original sales receipt.
It provides proof of purchase date in the event
of a warranty claim. See Warranty on page 11
for details.
Parts & Supplies
For Parts and Supplies, go to BISSELL.com and
enter your model number in the search field.
We c’t wait
to ar from y!
We really do read
your comments, tweets,
and posts.
Rate this product on
BISSELL.com
or any of our retailer sites
and let us (and millions of
your closest friends)
know what you think!
For cleaning tips and more visit www.BISSELL.com or find us at:
BISSELL BISSELLClean BISSELL BISSELLBISSELLClean
©2017 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 161-3252 08/17
12
Visit our website at: www.BISSELL.com
Loading...