More of a video
person? Look
for this icon and
go online for an
instructional
how-to video at
www.BISSELL.com
SPOTCLEAN PROHEAT
5207, 9749 SERIES
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR PORTABLE DEEP CLEANER.
When using an electrical appliance, basic precautions should be observed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY:
» Connect to a properly grounded
outlet only. See grounding
instructions. Do not modify the
3-prong grounded plug.
» Do not leave appliance when
it is plugged in. Unplug from
outlet when not in use and
before servicing.
» Do not expose to rain.
Store indoors.
» Do not allow to be used as a toy.
Close attention is necessary when
used by or near children.
» Do not use for any purpose other
than described in this User’s
Guide. Use only manufacturer’s
recommended attachments.
» Do not use with damaged cord or
plug. If appliance is not working as
it should, has been dropped, dam
aged, left outdoors, or dropped
into water, have it repaired at an
authorized service center.
» Always install float before any
wet pick-up operation.
» Do not pull or carry by cord, use
cord as a handle, close a door on
cord, or pull cord around sharp
edges or corners. Do not run
appliance over cord. Keep cord
away from heated surfaces.
» Do not unplug by pulling on
cord. To unplug, grasp the plug,
not the cord.
» Do not handle plug or appliance
with wet hands.
» Do not put any object into
openings. Do not use with any
opening blocked; keep openings
free of dust, lint, hair, and
anything that may reduce air flow.
» Keep hair, loose clothing, fingers,
and all parts of body away from
openings and moving parts.
» Turn off all controls before plug-
ging or unplugging appliance.
» Use extra care when cleaning
on stairs.
» Do not use to pick up flammable
or combustible materials (lighter
fluid, gasoline, kerosine, etc.)
or use in areas where they may
be present.
» Do not use appliance in an
enclosed space filled with vapors
given off by oil base paint, paint
thinner, some moth proofing
substances, flammable dust, or
other explosive or toxic vapors.
» Do not use to pick up toxic
material (chlorine bleach,
ammonia, drain cleaner, etc.).
» Do not pick up anything that
is burning or smoking, such as
cigarettes, matches, or hot ashes.
» Use only BISSELL cleaning prod
ucts intended for use with this
appliance to prevent internal com
ponent damage. See the Cleaning
Fluid section of this guide.
» Keep appliance on a level surface.
» Do not carry the appliance while
in use.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE
This model is for household use only. Commercial use of this unit voids the manufacturer’s warranty.
-
-
WARNING
Improper connection of the equipment-grounding conductor can
result in a risk of electrical shock. Check with a qualified electrician
or service person if you aren’t sure if the outlet is properly grounded.
DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper
outlet installed by a qualified electrician. This appliance is designed
for use on a nominal 120-volt circuit, and has a grounding attachment
plug that looks like the plug in the illustration. Make certain that the
appliance is connected to an outlet having the same configuration as
the plug. No plug adapter should be used with this appliance.
www.BISSELL.com
2
GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded wiring system. If it
should malfunction or break down, grounding provides a safe path
of least resistance for electrical current, reducing the risk of electrical
shock. The cord for this appliance has
an equipment-grounding conductor
and a grounding plug. It must only be
plugged into an outlet that is properly
installed and grounded in accordance
with all local codes and ordinances.
Grounded
Outlets
Grounding Pin
Th for buying a BISSELL portable dp cleer
We’re glad you purchased a
BISSELL SpotClean deep cleaner.
Everything we know about floor
care went into the design and
construction of this complete,
high-tech home cleaning system.
Your BISSELL SpotClean deep cleaner
is well made, and we back it with a
limited two year warranty. We also
stand behind it with a knowledgeable,
dedicated Consumer Care
department, so, should you ever
have a problem, you’ll receive fast,
considerate assistance.
My great-grandfather invented the
floor sweeper in 1876. Today, BISSELL
is a global leader in the design,
manufacture, and service of high
quality homecare products like your
BISSELL SpotClean deep cleaner.
Thanks again, from all of us at
BISSELL.
Safety Instructions...........2
Product View................4
Assembly ...................5
Operations ................5-7
Maintenance & Care .........8
Troubleshooting .............9
Accessories ................10
Warranty ....................11
Consumer Care..............11
Product Registration........12
Mark J. Bissell
Chairman & CEO
Tips
» Deep cleaning stairs and high-trac areas on a regular
basis helps prolong carpet life.
» Check upholstery stung before cleaning. Colored
stung may bleed through the fabric when it
becomes wet.
» Before turning o the machine, suction up clean
water to thoroughly rinse out the interior of the flex
hose. Then, lift the cleaning tool and point it upwards
to drain any remaining water into the dirty water/
collection tank.
www.BISSELL.com
3
Product View
2
1
3
9
6
10
4
1 Clean Water/Solution Tank
2 Power Button
3 Dirty Water Tank
4 Flex Hose Clip
5 Flex Hose
5
Cleaning fluid
Keep plenty of genuine BISSELL Cleaning
Solution on hand so you can clean whenever
it fits your schedule. Always use genuine
BISSELL deep cleaning formulas. Non-BISSELL
cleaning solutions may harm the machine and
may void the warranty.
To reduce the risk of fire and electric shock
due to internal component damage, use
only BISSELL cleaning fluids intended for use
with the deep cleaner.
Use only BISSELL portable machine formula
(with boost if desired) in your cleaner. Use
of cleaning formulas which contain lemon
or pine oil may damage this appliance and
void the warranty. Chemical spot cleaners
BISSELL 2X
Portable Machine
Pet Stain & Odor
Formula
or solvent-based soil removers also should
not be used. These products may react with
the plastic materials used in your cleaner,
causing cracking or pitting.
8
WARNING
WARNING
www.BISSELL.com
4
Go to www.BISSELL.com and
Asmbly
Assembling your portable machine is a
simple process.
1. Slide the flex hose clip into the opening on
the front of the machine. You will hear a “snap”
when it is locked into place.
2. Snap the hose grip bracket into the back of the
machine on the clean tank side. Wrap the flex hose
around the unit and snap hose grip into bracket.
3. Attach the cord wrap by snapping it into
place on the collection tank side of the machine.
Wrap the power cord around the cord wrap.
Snap the second tool storage (select models)
into the back of the machine between the cord
wrap and hose grip bracket.
search “5207 SpotClean Videos”
Operatis
Getting ready
1. To fill the clean water/solution tank a. Remove the tank by lifting it straight up
and away from the unit.
b. Pull on the black tab to reveal tank opening.
The plug rotates out of the way for easy filling.
c. FOR LARGE MESS: Follow the fill lines on
your clean tank to add the correct amount of
hot tap water (140°F/60°C MAX), portable
machine formula, and 1oz of BISSELL Boost.
FOR SMALL MESS: Follow the fill lines on
your clean tank to add the correct amount
of hot tap water (140°F/60°C MAX), and
portable machine formula. DO NOT BOIL
OR MICROWAVE WATER.
d. Replace the plug by rotating into place
and pressing gently onto tank.
e. Replace the tank by lining up tank bottom
with indentations on machine. Press down
firmly on tank to secure in position.
2. Release the flex hose from the hose grip bracket.
Unwrap flex hose completely from around the unit.
3. Select desired tool for spot cleaning. Insert
tool on end of hose until it clicks into place.
4. Twist the Quick Release™ cord wrap clockwise
to unwrap the power cord completely.
1.
2.
1a.
1e.
3.
4.
WARNING
Do not plug in your vacuum cleaner until
you are familiar with all instructions and
operating procedures.
1b.
www.BISSELL.com
5
Operatis
Pre-treating
Cleaning effectiveness will be enhanced if you
pre-treat heavily stained or highly soiled areas.
Here’s how to do it:
1. Attach the 3” Tough Stain Tool to the handheld
cleaning hose.
2. Plug in the unit and press the power button
beneath the handle to turn it on.
3. Hold the 3” Tough Stain Tool just above the
carpet or upholstery to be cleaned. Press the
trigger to mist solution over the soiled area. For
Deep Stain & 3-N-1 Stair Tool, follow instructions
on page 7.
4. Wait 3-5 minutes before cleaning.
Cleaning with the Tough Stain Tool
1. Attach the 3” Tough Stain Tool to the handheld
cleaning hose.
2. Plug in the unit and press the power button
beneath the handle to turn it on.
3. Hold the tool 1 inch above soiled surface.
4. Press the spray trigger to mist solution over
and onto the soiled area.
5. Release the spray trigger and gently scrub the
stain.
6. To lift the stain away, apply downward
pressure on the tool and slowly pull it toward
you. Watch as powerful suction removes the
dirt and cleaning solution. Continue until no
more dirt can be removed.
7. As a final step, use “drying strokes” (by not
pressing the spray trigger) to remove as much
moisture as possible. Repeat this step as often
as necessary.
NOTE: Oxy Boost formula will continue to clean
oxidizable stains for 6-8 hours.
WARNING
Keep spray away from face. Failure to do
so may result in personal injury.
IMPORTANT
Check the manufacturer’s tag before
cleaning upholstery. “W” or “WS” on the tag
means you can use your SpotClean. If tag
is coded with an “S” (with diagonal strikethrough), or says “Dry Clean Only,” do not
proceed. If manufacturer’s tag is missing or
not coded, check with your furniture dealer.
www.BISSELL.com
6
Go to www.BISSELL.com and
Operatis
search “5207 SpotClean Videos”
Cleaning with the Deep Stain Tool
(select models)
1. Attach the Deep Stain Tool to the handheld
cleaning hose.
2. Plug in the unit and press the power button
beneath the handle to turn it on.
3. Set the tool directly on top of the carpet
before pulling the spray trigger to inject formula
deep into your carpet fibers. Always keep the
Deep Stain Tool in direct contact with carpeting
to avoid over-spraying.
4. Release the spray trigger and gently scrub
the stain.
5. To lift the stain away, apply downward
pressure on the tool and slowly pull it toward
you. Watch as powerful suction removes the
dirt and cleaning solution. Continue until no
more dirt can be removed.
6. As a final step, use “drying strokes” (by not
pressing the spray trigger) to remove as much
moisture as possible. Repeat this step as often
as necessary.
NOTE: Oxy Boost formula will continue to clean
oxidizable stains for 6-8 hours.
Cleaning with the 3-in-1 Stair Tool (select models)
This versatile 3-way tool sprays, scrubs, and
suctions up dirt and stains from the outer
curves, corner, and tread of carpet staircase.
1. Twist the tool head to desired setting to clean
carpeted stair. The downward facing edge is the
active cleaning mode.
a. Use the flat area to clean top of stairsb. Use pointed edge to clean inside crevicec. Use indented area to clean outer corner
(nose) of stairs
2. Ensure the tool spray tip is pointing
downward. Pressing trigger, slowly move the
tool back and forth over the soiled surface
keeping the tool in contact with the carpet.
3. Release trigger and move tool slowly over
the soiled area to suction up water and dirt.
4. Continue to clean the area until no more
dirt can be removed.
a.b.c.
123
FLAT
NOSE
CREVICE
www.BISSELL.com
7
Mainnce & Care
After cleaning
1. Unplug power cord from outlet.
2. Empty and rinse the dirty water tank after
each use, OR when dirty water reaches the
indicated maximum fill line.
a. To remove the dirty water collection tank,
simply lift up on the tank from the base of
the machine.
b. Pull tab to remove plug from tankc. Rinse out dirty tank with clean water
after emptying.
d. Disconnect the cleaning tool from the
hose grip by pushing down on button lock
and pulling straight off. (Do NOT twist tool
to remove it).
e. The front of the Tough Stain Tool, Deep
Stain Tool & 3-N-1 Stair Tool can be removed
for easy cleaning. Push the button at the
top of the tool and slide the front of the tool
off the base. Rinse both under water and
replace the front of the tool.
f. Check spray nozzle for accumulated dirt or
debris. If necessary, clean with soft bristle brush.
g. The float stack can be removed from the
dirty tank for cleaning. Turn it counter-clock-
wise to remove it. Rinse with water until all
debris is removed. Replace the float stack in
the dirty tank and turn clockwise to lock.
Machine storage
1. Wipe all surfaces with a soft cloth.
2. Wrap power cord around the cord wrap on
the back of the machine.
3. Wrap flex hose around the base of the unit
and secure the spray trigger.
4. Store unit in protected, dry area, at room
temperature (40° to 110°F).
Thermal protector
An internal thermal protector has been designed
into your cleaner to protect it from overheating.
When the thermal protector activates, the suction motor will stop operating. If this happens,
proceed as follows:
1. Turn the cleaner OFF (O) and unplug from
electrical outlet.
2. Check the end of the hose and tool for
blockages and remove if necessary.
3. Check the float stack for clogs. Refer to
step 2g in the cleaning instructions above.
4. When the motor cools for approximately 30
minutes, the thermal protector automatically
resets and cleaning may continue. If the thermal
protector continues to activate after following the
above steps, your cleaner may need servicing.
Call BISSELL Consumer Care or visit the website.
WARNING
To reduce the risk of electric shock, turn power switch
o and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.
2g.
www.BISSELL.com
8
Trbleshting
WARNING
To reduce the risk of electric shock, turn power switch
o and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.
ProblemPossible causesRemedies
Reduced
spray or
no spray
Spray nozzle cloggedClean spray nozzle using an unfolded
Clean water/solution tank emptyCheck/fill tank
Clean water/solution tank insert
clogged
Pump needs primingGently lift clean water/solution tank
paper clip
Clean insert at bottom of clean water/
solution tank
while depressing the spray trigger
OR gently squeeze clean tank while
depressing spray trigger
Spot cleaner
won’t pick
up cleaning
solution
Deep Stain
Tool is
Over-Spraying
Formula
(Formula is
Spraying
Out the Sides)
Dirty Water
Tank Leaking
Poor upholstery/carpet
tool position
Dirty water tank is fullEmpty dirty water tank
Upholstery/carpet tool brush worn Replace with new brush
Excess solution in flex hoseLift tool and point upwards to allow
Formula trigger is being pulled
when tool is above carpeting
Deep Stain Tool is being used on
upholstery
Duckbill valve is dirtyClean the duckbill valve that is
Reposition upholstery/carpet tool
on surface, follow recommended
cleaning procedures
water in hose to flow into the dirty
water tank
formulas only
Make sure the Deep Stain Tool’s
formula injection needles are
burrowed deeply within your
carpeting before pressing the formula
spray trigger. To avoid over-spraying,
make sure the tool stays in direct
contact with the carpet at all times.
The Deep Stain Tool is designed for
high-pile carpets and rugs. Switch to
the 3” Tough Stain Tool for upholstery
cleaning.
located at the bottom of the dirty
water tank. Once cleaned, make
sure it is placed securely back in
place.
Please do
not return
this product
to the store.
Other maintenance or service not included in the manual should
be performed by an authorized service representative.
Thank you for selecting a BISSELL product.
For any questions or concerns, BISSELL is happy to
be of service. Contact us directly at 1-800-237-7691.
www.BISSELL.com
9
Cleing Formulas
CLEANING FORMULAS
79B92X Portable Machine Spot &
Stain Formula 32oz
1405Oxy Boost 16oz1406Renew Boost 16oz
1407Prevent Boost 16oz
74R72X Portable Machine Pet Stain
& Odor 32oz
www.BISSELL.com
10
WarrtyService
This warranty gives you specific legal rights, and you may also
have other rights which may vary from state to state. If you need
additional instruction regarding this warranty or have questions
regarding what it may cover, please contact BISSELL Consumer Care
by E-mail, telephone, or regular mail as described below.
Limited Two-Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon
receipt of the product BISSELL will repair or replace (with new or
remanufactured components or products), at BISSELL’s option, free of
charge from the date of purchase by the original purchaser, for two
years any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial
or rental service. This warranty does not apply to fans or routine
maintenance components such as filters, belts, or brushes. Damage or
malfunction caused by negligence, abuse, neglect, unauthorized repair,
or any other use not in accordance with the User's Guide is not covered.
BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S
LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or
limitation of incidental or consequential
damages, so the above limitation or exclusion
may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM
THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER
WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES
WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO THE two YEAR DURATION FROM THE DATE
OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied
warranty last so the above limitation may not apply to you.
NOTE: Please keep your original sales
receipt. It provides proof of date of
purchase in the event of a warranty claim.
If your BISSELL product should
require service:
Contact BISSELL Consumer Care to locate a BISSELL Authorized
Service Center in your area.
If you need information about repairs or replacement parts,
or if you have questions about your warranty, contact BISSELL
Consumer Care.
Website or E-mail:
www.BISSELL.com
Or Call:
BISSELL Consumer Care
1-800-237-7691
Monday – Friday 8am - 10pm ET
Saturday 9am - 8pm ET
Sunday 10am - 7pm ET
www.BISSELL.com
11
Regr yr product tod!
Registering is quick, easy and offers you benefits over the lifetime of your product.
BISSELL Rewards Points
Automatically earn points for
discounts and free shipping on
future purchases.
Faster Service
Supplying your information now
saves you time should you need to
contact us with questions regarding
your product.
You’ll receive:
Product Support Reminders
and Alerts
We’ll contact you with any
important product maintenance
reminders and alerts.
Special Promotions
Optional: Register your email
to receive notice of offers,
contests, cleaning tips and more!
Visit www.BISSELL.com/registration now!
BISSELL Csumer Care
For information about repairs or replacement parts, or questions about your warranty:
Call:
BISSELL Consumer Care
1-800-237-7691
Monday - Friday 8 am - 10 pm ET
Saturday 9 am - 8 pm ET
Sunday 10am - 7pm ET
Email:
www.BISSELL.com/email-us
Visit the BISSELL website: www.BISSELL.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of purchase
date in the event of a warranty claim. See Warranty on page 11 for details.