Bissell Readyclean 47B2, Readyclean 40N7, Readyclean 20R7, Readyclean 40H5 User Manual

®
USER GUIDE
READYCLEAN
47B2, 20R7, 40H5, 40N7 SERIES
READ ALL INSTRUCTIONS BEFORE USING YOUR DEEP CLEANER.
When using an electrical appliance, basic precautions should be observed, including the following:
WARNING
To reduce The risk of fire, elecTric shock, or injury:
» Connect to a properly grounded
outlet only. See grounding instructions. Do not modify the 3-prong grounded plug.
» Do not leave appliance when it is
plugged in. Unplug from outlet when
not in use and before servicing. » Use indoors only. » Do not allow to be used as a toy.
Close attention is necessary when
used by or near children. » Do not use for any purpose other
than described in this User ’s
Guide. Use only manufacturer’s
recommended attachments. » Do not use with damaged cord
or plug. If appliance is not
working as it should, or has been
dropped, damaged, left outdoors,
or dropped into water, have it
repaired at an authorized
service center.
» Do not pull or carry by cord, use
cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
» Do not unplug by pulling on
cord. To unplug, grasp the plug, not the cord.
» Do not handle plug or appliance
with wet hands.
» Do not put any object into open-
ings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.
» Keep hair, loose clothing, fingers,
and all parts of body away from openings and moving parts.
» Turn off all controls before plug-
ging or unplugging appliance.
» Use extra care when cleaning
on stairs.
» Do not use to pick up flammable
or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.
» Do not use appliance in an
enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors.
» Do not use to pick up toxic
material (chlorine bleach, ammonia, drain cleaner, etc.).
» Do not pick up anything that
is burning or smoking, such as cigarettes, matches, or hot ashes.
» Use only BISSELL cleaning
products intended for use with this appliance to prevent internal component damage. See the Cleaning Fluid section of this guide.
» Do not immerse. Use only on
surfaces moistened by the
cleaning process. » Keep appliance on a level surface. » Do not carry the appliance while
in use.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
This model is for household use only. Commercial use of this unit voids the manufacturer’s warranty.
WARNING
Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you aren’t sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the illustration. Make certain that the appliance is connected to an outlet having the same configuration as the plug. No plug adapter should be used with this appliance.
www.BISSELL.com
2
800.237.7691
GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded wiring system. If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electrical shock. The cord for this appliance has an equipment-grounding conductor and a grounding plug. It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Grounded Outlets
Grounding Pin
Th for buying a BISSELL dp cleer
We’re glad you purchased a BISSELL deep cleaner. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system.
Your BISSELL deep cleaner is well made, and we back it with a limited one-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Care department, so, should you ever have a problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global leader in the design, manufacture, and service of high quality homecare products like your BISSELL deep cleaner.
Thanks again, from all of us at BISSELL.
Safety Instructions...........2
Product View................4
Assembly ...................5
Operations ................6-7
Maintenance & Care .........8
Troubleshooting .............9
Replacement Parts .........10
Accessories ................10
Warranty ....................11
Consumer Care..............11
Product Registration........ 12
Mark J. Bissell Chairman & CEO
Tips
» Deep cleaning stairs and high-trac areas on a regular
basis helps prolong carpet life.
» Check upholstery stung before cleaning. Colored
stung may bleed through the fabric when it becomes wet.
www.BISSELL.com
» Before turning o the machine, suction up clean
water to thoroughly rinse out the interior of the flex hose. Then, lift the cleaning tool and point it upwards to drain any remaining water into the dirty water/ collection tank.
800.237.7691
3
Product View
1 Spray Trigger 2 Upper Handle 3 Retractable Handle Lock 4 Power Cord 5 Upper Body 6 Solution Tank 7 Vent Cover ( Foam Filter) 8 Collection Tank Latch 9 Removable Nozzle
1
2
3
4
5
6
7
8
9
Cleaning fluid
Keep plenty of genuine BISSELL 2X formula on hand so you can clean and protect whenever it fits your schedule. Always use genuine BISSELL deep cleaning formulas. Non-BISSELL cleaning solutions may harm the machine and will void the warranty.
Professional
Deep Cleaning
Best for
2X Concentrated X X X X X X
Scotchgard™ Protection
Out cleans
all other formulas
®
Pet Stain & Odor
Removes tough pet stains and contains
patented odor
removal technology
X X X
Deep Clean
& Protect
Deep cleans carpets
and protects from future stains with
Scotchgard™ Protector
Allergen Cleansing Deep Clean + Oxy Pet Stain PreTreat Stain PreTreat
Helps remove pet &
pollen allergens
Permanently removes
tough stains
*ONLY BISSELL Protects from future stains with Scotchgard™ Protector
Scotchgard™ is a trademark of 3M®.
www.BISSELL.com
4
800.237.7691
WARNING
To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning fluids intended for use with the deep cleaner.
Pretreat to help
remove tough pet
stains and odors
Pretreat to
penetrate
and loosen
tough stains
Hard Floor
Solutions™ formula
For use with the
Bare Floor Tool
(select models)
Asmbly
Your deep cleaner assembles quickly and easily. The only tool you will need for assembly is a Phillips head screwdriver.
1. Slide upper body onto lower body.
2. Secure with screws.
3. Slide upper handle into upper body by
aligning the pin and sliding into place.
NOTE: Be sure to secure upper handle before lifting. Rotate handle lock clockwise to secure.
4. Place solution tank on back of unit.
5. Wrap power cord.
Assembly is now complete.
Operatis
Before you clean
1. Move furniture to another area if cleaning an entire room. (Optional)
2. Vacuum carpet thoroughly.
3. Plan your cleaning route to leave an exit path.
It is best to begin cleaning in the corner farthest from your exit.
4. Pre-Treating (optional) Pre-treat stubborn stains and highly soiled carpet in hallways and other high-traffic areas.
a. Generously spray BISSELL Pretreat evenly
over soiled area.
Caution: DO NOT OVER WET CARPET
b . Wait 3-5 minutes before deep cleaning.
pin
3.
WARNING
Do not plug in your deep cleaner until you are familiar with all instructions and operating procedures.
1.
2.
4.
Tip
» Deep cleaning carpeting regularly can reduce dust and allergens in your home.
www.BISSELL.com
800.237.7691
5
Operatis
Fill the tank
1. Remove the solution tank by lifting it straight up, then away from the lower body.
2. Unscrew the black cap at the bottom of the solution tank.
3. Fill with hot (not boiling) tap water (140°F/60°C MAX) to the WATER line. Fill the rest of the tank with BISSELL 2X Formula to the FORMULA line. Replace and tighten the black cap.
Caution: Do not microwave or boil water before filling.
4. Place solution tank on lower body.
Carpet cleaning
1. Plug into proper outlet.
2. Adjust the retractable handle by turning
counterclockwise and lifting the handle up. Turn clockwise to secure.
3. With foot, press the red power button, located on the back of the machine.
NOTE: Handle must be in the full upright position before cleaning.
4. With foot, press the grey recline lever. located next to power button.
5. Cleaning Strokes. While pressing the trigger, make one slow forward wet pass and another one back.
6. Release the trigger and make one slow forward and backward pass over the same area.
7. Repeat steps 5 and 6 until solution being pulled up appears clean.
8. Empty the collection tank when dirty water reaches the full line, or when the solution tank is empty.
Caution: Do not overwet.
2.
1.
2.
4.3.
3.
Power
4.
Recline
Empty the collection tank
1. With foot, press the red power button, to turn off and unplug power cord from outlet.
2. Remove the collection tank from base of unit. a. Release collection tank latches (on each
side) by pulling up from the bottom of latch and then out.
b . Carefully remove tank by lifting up on the
tank handle.
3. Carry collection tank to a toilet or sink. To empty, pour out contents using opening at back of tank.
4. Rinse collection tank thoroughly and replace on unit.
5. Refill solution tank and continue cleaning. www.BISSELL.com
6
800.237.7691
2a.
2b.
3.
Operatis
Hard floor cleaning (select models only)
1. Remove the collection tank (refer to steps
2a and 2b on page 6).
2. Attach the hard floor tool by hooking it into
the front of the removable nozzle and rotate until it snaps firmly in place.
3. Replace the collection tank. Be sure to attach
the two latches.
4. Fill the solution tank with hot (not boiling)
tap water (140°F/60°C MAX) to the WATER fill line. Fill the rest with BISSELL 2X Hard Floor Solutions™ to FORMULA fill line.
5. Follow steps 1-8 under “Carpet Cleaning” on
page 6 to continue cleaning.
Cleaning after use
1. Unplug the unit.
2. Remove and rinse collection tank thoroughly.
3. Remove tank vent & foam filter (located on
top of the collection tank) and rinse.
4. Clean nozzle window by lifting latch and
removing nozzle from machine. Rinse under running water.
5. 40N7 and 40H5 series models, pop out
CrossAction brush by pushing the tabs away from each other and pushing down. Once the brush pops out, rinse and replace by snapping the tabs back into place.
6. When finished replace nozzle and secure
with latch.
NOTE: For best results, it is recommended that the nozzle is cleaned after each use.
7. Remove lint and hair from red gasket in
base of unit. (Do not remove gasket)
8. Replace the collection tank on the base of
the machine and secure with latches.
2. 4.
3. 4.
6. 7.
WARNING
To reduce the risk of fire and electric shock- when cleaning a hard floor, the BISSELL hard floor tool (203-5683) must be used and it must only be used with BISSELL 2X Hard Floor Solutions cleaning fluid intended for use with this appliance.
5.
www.BISSELL.com
800.237.7691
7
Mainnce & Care
Machine storage
For best results, a few simple steps can assure your machine is well maintained after your cleaning is complete.
1. Wrap power cord around Quick Release
Cord Wrap™ on side of the machine.
2. Wipe all surfaces with a soft cloth. Store
cleaner upright in a protected, dry area.
NOTE: You may have cleaning solution remain­ing in the solution tank. You may store your machine this way for the next cleaning task, but never keep dirty water in the collection tank.
Install the replacement brush belt ­(For Model 47B2 and 20R7 Series only)
1. Turn the machine off and unplug from
wall outlet.
2. Remove solution and collection tanks.
3. Lay machine down to access the bottom
of the machine.
4. With a Phillips head screwdriver, unscrew
the belt cover and remove.
5. Remove the brush end cap and remove
belt from brush.
6. Brush can now be removed.
7. Belt can be removed by sliding off the
motor pulley.
8. Clean or replace belt. Attach belt to
motor pulley and brush, insert brush into right side end cap.
9. Reattach the left end cap and slide brush
back into place.
10. Replace the belt cover and screw into place.
11. Manually rotate brush to make sure it rotates
freely and that the belt is aligned properly.
WARNING
To reduce the risk of electric shock, turn power switch o and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.
CAUTION
Do not store unit where freezing may occur. Damage to internal components may result.
4.
5.
10.
www.BISSELL.com
8
800.237.7691
Loading...
+ 16 hidden pages