Biostar NF520D3 Owner's Manual

NF520D3 Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment ge nerates, uses, and can radiate radio frequency
energy and, if not i nstalled and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ........................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation .......................... 5

2.1 Installing Central Processing Unit (CPU) ....................................... 5

2.2 FAN Headers...................................................................................... 7

2.3 Installing System Memory ................................................................ 8

2.4 Connectors and Slots....................................................................... 10

Chapter 3: Headers & Jumpers Setup .................. 13

3.1 How to Setup Jumpers .................................................................... 13

3.2 Detail Settings.................................................................................. 13

Chapter 4: NVIDIA RAID Functions...................... 17

4.1 Operating System............................................................................ 17

4.2 Raid Arrays...................................................................................... 17

4.3 How RAID Works............................................................................. 17

Chapter 5: Useful Help ........................................ 19

5.1 Driver Installation Note.................................................................. 21

5.2 Software............................................................................................ 22

5.3 Award BIOS Beep Code.................................................................. 23

5.4 Extra Information............................................................................ 23

5.5 Troubleshooting............................................................................... 25

Appendix: SPEC In Other Languages ................... 26

German.................................................................................................................. 26

French .................................................................................................................... 28

Italian..................................................................................................................... 30

Spanish ................................................................................................................... 32

Portugue se ............................................................................................................ 34

Polish...................................................................................................................... 36

Russian ................................................................................................................... 38

Arabic..................................................................................................................... 40

Japanese ................................................................................................................ 42

CHAPTER 1: INTRODUCTION

NF520D3

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short
circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

 The operating temperatures of the computer should be

0 to 45 degrees Celsius.

1.2 PACKAGE CHECKLIST

HDD Cable X 1 (optional)
Serial ATA Cable X 2
Rear I/O Panel for ATX Case X 1
User’s Manual X 1
Fully Setup Driver CD X 1
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
S/PDIF out Cable X 1 (optional)

Note: The package contents may be different due to area or your motherboard version.

1

Motherboard Manual

1.3 MOTHERBOARD FEATURES

Socket AM3

CPU

FSB

Chipset

Super I/O

Main

Memory

IDE

SATA

LAN

Sound

Slots

On Board

Connectors

AMD Phenom II/ Athlon II processors

(Maximum Watt: 95W)

Support HyperTransport 2.0

Supports up to 2.0 GT/s Bandwidth

nVIDIA nForce 520

ITE 8718F

Prov ides the most commonly us ed legacy

Super I/O functionality.

DDR3 DIMM Slots x 4

Max Memory Capacity 16GB

Each DIMM supports 512MB/

1GB/2GB/4GB DDR3

Int egr at ed ID E Contro ller

Integrated Serial ATA Controller

Realtek RTL 8111DL

ALC662

PCI Slot x3 Supports PCI expansion cards

PCI Express x16 Slot x1 Supports PCI-E x16 expansion card

PCI Express x 1 Slot x1 Supports PCI-E x1 expansion cards

Floppy Connector x1 Each connector supports 2 Floppy drives

Printer Port Connector x1 Each connector supports 1 Printer port

IDE Conn ector x1 Each conne ctor s upports 2 IDE device

SATA Connector x4 Each conne ctor s upports 1 SATA devices

SPEC

AMD 64 Architecture enables 32 and 64 bit computing

Supports Hyper Transport 2.0

Low Pin Count Interface

En v ironm en t Cont rol init iatives ,

H/W Mon ito r

Fan Sp eed Controller

ITE's "S mart Guard ian" function

Dual Channel Mode DDR3 me mory mo du le

Supports DDR3 800 / 1066 / 1333

Register ed DIMM and ECC D IMM is not supported

Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode

supports PIO Mode 0~4,

Data transfer rates up to 3.0 Gb/s.

SATA Version 2.0 s p e c if icat ion co mpliant .

10 / 100 Mb/s / 1Gb/s auto negot iation

Half / Full duplex capability

5.1 channels audio out

Supports HD Audio

2

Back Panel

I/O

Board Size

Special

Feature

OS Support

NF520D3

SPEC

Front Panel Connector x1 Supports front panel facilities

Front Audio Connector x1 Supports front panel audio function

S/PDIF out Connector x1 Supports digital audio out function

CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)

System Fan Header x1 System Fan Power supply

USB Connecto r x2 Each connecto r supports 2 front panel USB ports

CMOS clear Header x1 Restore CMOS data to factory default

Power Connector (24pin) x1 Connects to Power supp ly

Power Connector (4pin) x1 Connects to Power supply

PS/2 Keyboard x1

PS/2 Mous e x1

Serial Port x1

LAN port x1

USB Port x4

Audio Jack x3

200 mm (W) x 293 mm (L)

RAID 0 / 1 / 0+1 / 5 support

Windows XP / Vista / 7

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connects to RS-232 Port

Connect to RJ- 45 ethe rnet cab le

Connect to USB devices

Provide Audio-In/Out and microphone connection

Biostar reserves the right to add or remove support for

any OS with or without notice.

1.4 REAR PANEL CONNECTORS

PS/2
Mouse

P S /2
Keyboard

COM1 USBX2USBX2

LAN

Line In/
Surround

Line Out

Mic In 1/
Bass/ Cente r

3

Motherboard Manual

1.5 MOTHERBOARD LAYOUT

KBMS1

J_PRI NT1

CO M1

USB1

RJ4 5USB11

AUDIO1

JUSBV1

F_AUDIO1

LAN

JATXPWR2

ATXPWR1

nFo rce

520

CPU_FAN1

Socket AM3

DDR3_A1

DDR3_B1

DDR3_B2

DDR3_A2

SATA3 SATA4

IDE1

4

Codec

JSPDIFOUT1

Super I/O

Note: represents the 1■

PEX1_1

PEX16_ 1

PCI1

PCI2

PCI3

st

pin.

BAT1

JCMO S1

SATA1 SATA2

F_USB1 F_USB2

FDD1

SYS_FAN1

BIOS

JUSBV2

PAN EL1

CHAPTER 2: HARDWARE INSTALLATION

NF520D3

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 2: Look for the white triangle on socket, and the gold triangle on

CPU should point forwards this white triangle. The CPU will fit
only in the correct orientation.

5

Motherboard Manual

Step 3: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the CPU_FAN1. This completes the
installation.

6

NF520D3

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.

CPU_FAN1: CPU Fan Header

14

SYS_FAN1: System Fan Header

Pin

Pin

Assignment

1 Ground
2 +12V
3 FAN RPM

rate sense

4

Smart Fan
Control

Assignment

1 Ground
2 +12V
3 FAN RPM rate

sense

31

Note:

CPU_FAN1 supports 4-pin head connector, and SYS_FAN1supports 3-pin head
connector. When connecting with wires onto connectors, please note that the red wire is
the positive and should be connected to pin#2, and the black wire is Ground and should
be connected to GND.

7

Motherboard Manual

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

DDR3_A1

DDR3_B1

DDR3_A2

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.

DDR3_B2

2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.

8

B. Memory Capacity

DIMM Socket

Location

DDR3_A1 512MB/1GB/2GB/4GB

DDR3_B1 512MB/1GB/2GB/4GB

DDR3_A2 512MB/1GB/2GB/4GB

DDR3_B2 512MB/1GB/2GB/4GB

DDR3 Module

Total Mem o ry

Size

Max is 16GB.

C. Dual Channel Memory installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status

Enabled O O X X

Enabled X X O O

Enabled O O O O

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or
x16)

DDR3_A1

DDR3_B1 DDR3_A2 DDR3_B2

NF520D3

9

Motherboard Manual

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types.

2

1

34

33

IDE1: Hard Disk Connector

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.

3940

21

SATA1 ~ SATA4: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 4 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.

Pin

Assignment

SATA 3 SATA4
SATA 1 SATA2

1

4

7

1 Ground
2 TX+
3 TX­4 Ground
5 RX­6 RX+
7 Ground

10

NF520D3

PEX16_1: PCI-Express x16 Slot

- PCI-Express 1.0a compliant.

- Maximum theoretical realized bandwidth of 4GB/s simultaneously per

direction, for an aggregate of 8GB/s totally.

PEX1_1: PCI-Express x1 Slot

- PCI-Express 1.0a compliant.

- Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

- 2X bandwidth over the traditional PCI architecture.

PEX1_1

PEX16_1

PCI1/PCI2/PCI3: Peripheral Component Interconnect Slots

This motherboard is equipped with 3 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.

PCI1

PCI2

PCI3

11

Motherboard Manual

ATXP W R1: AT X P ower Source Connector

ATXPWR1 allows user to connect 24-pin power connector on the AT X power
supply.

13

24

Pin Assignment Pin Assignment

1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 Gro und 15 Gro und
4 +5V 16 PS_ON
5 Gro und 17 Gro und
6 +5V 18 Ground
7 Gro und 19 Gro und
8 PW_OK 20 NC

9 Standb y Voltage+5V 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 Ground

ATXP W R2: AT X P ower Source Connector

This connector provides +12V to CPU power circuit.

2

1

12

1

43

Pin

Assignment

1 +12V
2 +12V
3 Ground
4 Ground

12

CHAPTER 3: HEADERS & JUMPERS SETUP

NF520D3

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.

Pin opened Pin closed Pin1-2 closed

3.2 D

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED,
speaker Connection. It allows user to connect the PC case’s front panel
switch functions.

ETAIL SETTINGS

9
1

PWR_LED

++

SPK

HLED

+

On/ Off

-

-

RST

16
8

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A
2 N/A 10 N/A
3 N/ A 1 1 N/ A N/A
4 Speaker

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)
7 Ground 15 Power button
8 Reset control

Speaker
Connector

Hard drive
LED

Reset button

12 Power LED (+)

14 Power LED (-)

16 Ground

N/A

Power LED

Power-on button

13

Motherboard Manual

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.

JSPDIFOUT1: Digital Audio-out Connector

This connector allows user to connect the PCI bracket SPDIF output header.

Pin Assignment

12

910

Pin

1 +5V
2 SPDIF_OUT
3 Ground

1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
5 Right line in
6 Jack Sense
7 Front Sense
8 Key
9 Left line in

10 Jack Sense

Assignment

14

31

JUSBV1/JUSBV2: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBV1: +5V for USB ports at USB1/RJ45USB1.
JUSBV2: +5V for USB ports at front panel (F_USB1/F_USB2).

Pin 2-3 Close:

JUSBV1: +5V STB for USB ports at USB1/ RJ45USB1.
JUSBV2: +5V STB for USB ports at front panel (F_USB1/F_USB2).

NF520D3

JUSBV1

3

1

13

JUSBV2

3

1

Pin 1-2 close

3

1

Pin 2-3 close

JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and
the CMOS data. Please carefully follow the procedures to avoid damaging the
motherboard.

13

13

13

Pin 1-2 Close:

Normal Operation
(default).

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

15

Motherboard Manual

F_PRINT1: Printer Port Connector

This header allows you to connector printer on the PC.

12

25

26

Pin Assignment Pin Assignment

1 -Strobe 14 Ground
2 -ALF 15 Data 6
3 Data 0 16 Ground
4 -Error 17 Data 7
5 Data 1 18 Ground
6 -Init 19 -ACK
7 Data 2 20 Ground
8 -Scltin 21 Busy

9 Data 3 22 Ground
10 Ground 23 PE
11 Data 4 24 Ground
12 Ground 25 SCLT
13 Data 5 26 Key

F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.

Assignment

Pin

1 +5V (fused)
2 +5V (fused)
3 USB­4 USB­5 USB+
6 USB+

F_USB1 F_USB2

2

10

7 Ground
8 Ground
9 Key

10 NC

16

1

9

CHAPTER 4: NVIDIA RAID FUNCTIONS

NF520D3

4.1 O

z Supports Windows XP, Windows Vista, and Windows 7.

PERATING SYSTEM

4.2 RAID ARRAYS

NVRAID supports the following types of RAID arrays:

RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for

many applications.

RAID 1: RAID 1 defines techniques for mirroring data.
RAID 0+1: RAID 0+1 combines the techniques used in R AID 0 and RAID 1.
RAID 5: RAID 5 provides fault to lerance and better utilizat ion of disk capacity.

4.3 HOW RAID WORKS

RAID 0:

The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks
up a large f i le into sma ller blocks an d pe rfo rms disk r ead s and writes acr oss multip le
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment. This
technique reduces overall disk access time and offers high bandwidth.

Features and Benefits

 Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the

platform.

 Uses: Intended for non-critical data requiring high data throughput, or any

environment that does not require fault tolerance.

 Benefits: provides increased data throughput, especially for large files. No

capacity loss penalty for parity.

 Drawbacks: Does not deliver any fault tolerance. If any drive in the array

fails, all data is lost.

 Fault Tolerance: No.

Blo ck 1
Block 3
Block 5

Block 2
Block 4
Block 6

17

Motherboard Manual

RAID 1:

Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on a
second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the
active volume or drive is corrupted or becomes unavailable because of a hardware failure.

RAID techniques can be applied for high-availability solutions, or as a form of automatic
backup that eliminates tedious manual backups to more expensive and less reliab le
media.

Features and Benefits

 Drives: Minimum 2, and maximum is 2.
 Uses: RAID 1 is ideal for small databases or any other application that

requires fault tolerance and minimal capacity.

 Benefits: Provides 100% data redundancy. Should one drive fail, the

controller switches to the other drive.

 Drawbacks: Requires 2 drives for the storage space of one drive.

Performance is impaired during drive rebuilds.

 Fault Tolerance: Yes.

18

Block 1
Block 2
Block 3

Block 1
Block 2
Block 3

NF520D3

RAID 0+1:

RAID 0 drives can be mirrored using RAID 1 techniques. Resulting in a RAID 0+1
solution for improved performance plus resiliency.

Features and Benefits

 Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
 Benefits: Optimizes for both fault tolerance and performance, allowing for

automatic redundancy. May be simultaneously used with other RAID levels
in an array, and allows for spare disks.

 Drawbacks: Requires twice the available disk space for data redundancy,

the same as RAID level 1.

 Fault Tolerance: Yes.

nForce

520

Block 1
Block 3
Block 5

Block 2
Block 4
Block 6

Block 1
Block 3
Block 5

Block 2
Block 4
Block 6

19

Motherboard Manual

RAID 5:

RAID 5 stripes both data and parity information across three or more drives. It writes
data and parity blocks across all the drives in the array. Fault tolerance is maintained by
ensuring that the parity information for any given block of data is placed on a different
drive from those used to store the data itself.

Features and Benefits

 Drives: Mini mu m 3.
 Uses: RAID 5 is recommended for transaction processing and general

purpose service.

 Benefits: An ideal combination of good performance, good fault tolerance,

and high capacity and storage efficiency.

 Drawbacks: Individual block data transfer rate same as a single disk. Write

performance can be CPU intensive.

 Fault Tolerance: Yes.

Disk 1

DATA 1

DATA 3

PARIT Y

DATA 7
DATA 9

PARIT Y

Disk 2

nForce

520

DATA 2

PARIT Y

DATA 5
DATA 8

PARIT Y
DATA 11

Disk 3

PARIT Y

DATA 4
DATA 6

PARIT Y
DATA 10
DATA 12

※ For more detailed setup information, please refer to the Driver CD, or go to

http://www.nvidia.com/object/IO_28159.html to download the NVIDIA RAID User’s G uide.

20

CHAPTER 5: USEFUL HELP

NF520D3

5.1 D

RIVER INSTALLATION NOTE

After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.

You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader so ftware from
http://www.adobe.com/products/acrobat/readstep2.html

21

Motherboard Manual

5.2 SOFTWARE

Installing Software

1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.

2. Select Software Installation, and then click on the respective software
title.

3. Follow the on-screen instructions to complete the installation.

BIOScreen Utility

This utility allows you to personalize your boot logo easily. You can choose
JPG or BMP as your boot logo so as to customize your computer.

Please follow the following instructions to update boo logo:

1. Load Image：Choose the picture as the boot logo.

2. Transform：Transform the picture for BIOS and preview the result.

3. Update Bios：Write the picture to BIOS Memory to complete the update.

22

5.3 AMI BIOS BEEP CODE

Boot Block Beep Codes

Number of Beeps Description

1 No media present. (Insert diskette in floppy drive A:)

2

3 Insert next diskette if multiple diskettes are used for recovery
4 Flash Programming successful
5 File read error

7 No Flash EPROM detected
10 Flash Erase error
11 Flash Program error
12 “AMIBOOT.ROM” file size error

13

POST BIOS Beep Codes

Number of Beeps Description

1 Memory refresh timer error

3 Base memory read/write test error

6 Keyboard controller BAT command failed

7 General exception error (processor exception interrupt error)

8 Display memory error (system video adapter)

“AMIBOOT.ROM” file not found in root directory of diskette in
A:

BIOS ROM image mismatch (file layout does not match
image present in flash device)

NF520D3

Troubleshooting POST BIOS Beep Codes

Number of Beeps Troubleshooting Action

1, 3 Reseat the memory, or replace with known good modules.

Fatal error indicating a serious problem with the system.
Consult your system manufacturer. Before declaring the
motherboard beyond all hope, eliminate the possibility of
interference by a malfunctioning add-in card. Remove all
expansion cards except the video adapter.

6, 7

8

z If beep codes are generated when all other expansion

cards are absent, consult your system manufacturer’s
technical support.

z If beep codes are not generated when all other expansion

cards are absent, one of the add-in cards is causing the
malfunction. Insert the cards back into the system one at a
time until the problem happens again. This will reveal the
malfunctioning card.

If the system video adapter is an add-in card, replace or
reseat the
video adapter. If the video adapter is an integrated part of the
system board, the board may be faulty.

23

Motherboard Manual

5.4 EXTRA INFORMATION

CPU Overheated

If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdow n
automatically to avoid a damage of the CPU, and the system may not
power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection
function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.

(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

24

5.5 TROUBLESHOOTING

Probable Solution

1. There is no power in the system.
Power LED does not shine; the
fan of the power supply does not
work

2. Indicator light on keyboard does
not shine.

System is inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drives are running.

System does not boot from a hard disk
drive, but can be booted from optical
drive.

System only boots from an optical
drive. Hard disks can be read,
applications can be used, but system
fails to boot from a hard disk.

Screen message shows “Invalid
Configuration” or “CMOS Failure.”

System cannot boot after user installs a
second hard drive.

NF520D3

1. Make sure power cable is
securely plugged in.

2. Replace cable.

3. Contact technical support.

Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.

1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.

2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.

1. Back up data and applications
files.

2. Reformat the hard drive.
Re-install applications and data
using backup disks.

Review system’s equipment. Make sure
correct information is in setup.

1. Set master/slave jumpers
correctly.

2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

25

Motherboard Manual

APPENDIX: SPEC IN OTHER LANGUAGES

G

ERMAN

Sp ezif ika tio nen

CPU

FSB

Chipsatz

Super E/A

Arbeitsspeiche

r

IDE

SATA II

LAN

Audio-Codec

Steckplätze

Onboard-Ansc

hluss

26

Sockel AM3

AMD Phenom II/ Athlon II Prozessoren

(Maximales Watt: 95W)

Unterstützt HyperTransport 2.0 mit einer

Bandbreite von bis zu 2.0 GT/s

nVIDIA nForce 520

ITE 8718F

Biet et die h äufig ver wendeten a lten Super

E/A-Funktionen.

Low Pin Count-Schnittstelle

DDR3 DIMM-Steckplätze x 4

Max. 16GB Arbeitsspeicher

Jeder DIMM unterstützt 512MB/

1GB/2GB/4GB DDR3.

Int eg r iert er IDE-Co n t rolle r

Integrierter Serial ATA-Controller

Realtek RTL 8111DL

ALC662

PCI-Steckplat z x3

PCI Express x16 Steckplatz x1

PCI Express x 1-Steckplatz x1

Diskettenlaufwerkanschluss x1 Jeder Anschluss unterstützt 2 Diskettenlaufwerke

Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss

IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke

SATA-Anschluss x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk

Die AMD 64-Architektur unterstützt eine 32-B it- und

64-Bit-Datenverarbeitung

Unterstützt Hyper Transport 2.0

Umgebungskontrolle,

Hardware-Überwachung

Lüfterdrehz ahl-Cont roller

"Smart Guardian"-Funktion von ITE

Dual-Kanal DDR3 Speichermodul

Unterstützt DDR3 800 / 1066 / 1333

registrierte DIMMs. ECC DIMMs werden nicht

unterstützt.

Ultra DMA 33 / 66 / 100 / 133 Bus Master-Modus

Unterstützt PIO-Modus 0~4,

Datentransferrate b is zu 3Gb/s

Konform mit der SATA-Spezifikation Version 2.0.

10 / 100 / 1000 Mb/s Auto-Negotiation

Halb-/ Vollduplex-Funktion

5.1-Kanal-Audioausgabe

Unterstützt High-Definition Audio

Rückseiten-E/

A

Plat inengröße.

Sonderfunktio

nen

OS-Unterstütz

ung

NF520D3

Sp ezif ika tio nen

Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen

Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion

S/PDIF- Ausgangsanschluss x1

CPU-Lüfter-Sockel x1

System-Lüfter-Sockel x1 System-Lüfter-Stromversorgungsanschluss

"CMOS löschen "-So cke l x1

USB-Anschluss x2 Jeder Anschluss unterstützt 2

Stromanschluss (24-polig) x1

St r oman s chluss (4-pol ig ) x1

PS/2-Tastatur x1

PS/2- Maus x1

Serieller Anschluss x1

LAN-Anschluss x1

USB-Anschluss x4

Audioanschluss x3

200 mm (B) X 293 mm (L)

Unterstützt RAID 0 / 1 / 0+1 / 5

Windows XP / Vista / 7

CPU-Lüfterstromversorgungsanschluss (mit Smart

Fan -F un ktio n)

Fronttafel-USB-Anschlüsse

Biostar behält sich das Recht vor, ohn e Ankündigung

die Unterstützung für ein Betriebssystem

hinzuzufügen oder zu entfernen.

27

Motherboard Manual

FRENCH

SPEC

UC

Bus frontal

Chipset

Super E/S

Mémoire

principale

IDE

SATA II

LAN

Codec audio

Fentes

Connecteur

embarqu é

Socket AM3

Processeurs AMD Phenom II/ Athlon II

(Wat t maximu m : 95W)

Prend en charge Hyper Transport 2.0

jusqu'à une bande passante de 2.0 GT/s

nVIDIA nForce 520

ITE 8718F

Fournit la fonctionnalité de Super E/S

patrimoniales la plus utilisée.

Fentes DDR3 DIMM x 4

Capacité mé mo ire max ima le de 16 Go

Chaque D IMM prend en charg e des DDR3

de 512Mo/1Go/2Go/4Go

Contrôleur IDE intégré

Contrô leur Serial ATA int é gr é

Realtek RTL 8111DL

ALC662

Fente PCI x3

Slot PCI Express x16 x1

Slot PCI Express x 1 x1

Connecteur de disquette x1

Connecteur de Port d'imprimante x1 Chaque connector prend en charge 1 Port d'imprimante

L'architecture AMD 64 permet le calcul 32 et 64 bits

Prend en charge Hyper Transport 2.0

Int e rface à f aib le co mpte de b roches

Initiatives de contrôle environnementales,

Mon iteur d e mat ér iel

Contrôleur de vitesse de ventilateur

Fonction "Gardien intelligent" de l'ITE

Modu le d e mé mo ire DDR3 à mo d e à do uble vo ie

Prend en charge la DDR3 800 / 1066 / 1333

Les DIMM à registres et DIMM avec code correcteurs

d'erreurs ne sont pas prises en charge

Mode principale de Bus Ultra DMA 33 / 66 / 100 / 133

Prend en charge le mode PIO 0~4,

Taux de transfert jusqu'à 3 Go/s.

Co nforme à l a s p écificat ion SATA Ver s ion 2.0

10 / 100 / 1000 Mb /s négo ciat ion automatique

Half / Full duplex capability

Sortie audio à 5 .1 vo ies

Prise en ch arg e de l'audio haute déf in it ion

Chaque connect or prend en ch arg e 2 lecteurs de

disquettes

28

SPEC

NF520D3

E/S du

panneau

arrière

Dimensions

de la carte

Fonctionnali

tés

spéciales

Support SE

Connecteur IDE x1

Connecteur SATA x4

Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant

Connecteur Audio du panneau avant x1 Prend en charge la fonction aud io du panneau avant

Connecteur de sortie S/PDIF x1

Embase de ventilateur UC x1

Embase de ventilateur système x1 Alimentation électrique du ventilateur système

Embase d'effacement CMOS x1

Connecteur USB x2

Connecteur d'aliment at ion x 1

(24 broches)

Connecteur d'aliment at ion x1

(4 broch es )

Clavier PS/2 x1

Souris PS/2 x1

Port série x1

Port LAN x1

Port US B x4

Fiche audio (Ver 5.x) x6

Fiche audio (Ver 6.x) x3

200 mm (l) X 293 mm (H)

Prise en charge RAID 0 / 1 / 0+1 / 5

Windows XP / Vista / 7

Chaque connecteur pr end en ch arg e 2 périp hér iqu es

IDE

Chaque connecteur pr end en ch arg e 1 périp hér iqu e

SATA

Alimentation électrique du ventilateur UC (avec

fonction de ventilateur intelligent)

Chaque connecteur prend en charge 2 ports USB de

panneau avant

Biostar se réserve le droit d'ajouter ou de supprimer le

support de SE avec ou sans préavis.

29

Motherboard Manual

ITALIAN

Socket AM3

CPU

Processori AMD Phenom II/ Athlon II

SPECIFICA

L’archit ett u ra AMD 64 abilita la co mput azione 32

e 64 bit

FSB

Chipset

Super I/O

Memoria
principale

IDE

SATA II

LAN

(Watt massimo: 95W)

Supporto di HyperTransport 2.0 fino a

2.0 GT/s di larghezza di banda

nVIDIA nForce 520

ITE 8718F

Fo rnis ce le f unz ion al it à leg a cy Super

I/O usate più comunemente.

Interfaccia LPC (Low Pin Count)

Alloggi DIMM DDR3 x 4

Capacità mass ima della memoria 16GB

Ciascun DIMM supporta DDR3

512MB/1GB/2GB/4GB

Co n troller IDE int eg rat o

Co ntroller Ser ia l ATA in t eg rato

Realtek RTL 8111DL

Supporto di Hyper Transport 2.0

Funzioni di controllo dell’ambiente:

Monitoraggio hardware

Co ntroller velo c it à ventolin a

Funzione "Smart Guardian" di ITE

Modulo di memoria DDR3 a canale doppio

Supporto di DDR3 800 / 1066 / 1333

DIMM registrati e DIMM ECC non sono supportati

Modalità Bus Master Ultra DMA 33 / 66 / 10 0 / 133

Supporto modalità PIO Mode 0-4

Velocità di trasferimento dei dati fino a 3 Gb/s.

Co mp at ib ile s p ec if iche S ATA Vers ione 2.0.

Negoziazione automatica 10 / 100 / 1000 Mb/s

Capacità Half / Full Dup lex

Codec
audio

Allo g g i

Connettori
su scheda

30

ALC662

Uscita audio 5.1 canali

Supporto audio High-Definition (HD)

Allo g g io PC I x3

Alloggio PCI Express x16 x1

Alloggio PCI Express x1 x1

Connettore floppy x1 Ciascun connettore supporta 2 unità Floppy

Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante

Connettore IDE x1 Ciascun connettore supporta 2 unità IDE

NF520D3

SPECIFICA

Connettore SATA x4 Ciascun connettore supporta 1 unità SATA

Co nnett o re pannello fr ontale x 1 Suppo rta i s ervizi de l p an nello front ale

Connettore audio frontale x1 Supporta la funzione audio pannello frontale

Connettore output SPDIF x1

I/O
pannello
posteriore

Dimension
i scheda

Caratterist
iche
speciali

Sistemi
operativi
supportati

Co lletto r e ventolina C PU x1

Co lletto r e ventolina sistema x 1 Alimentaz ione vent o lina d i s is tema

Co lletto r e cance llaz ione CMOS x1

Connettore USB x2

Connettore alimentaz ione x1

(24 pin)

Connettore alimentaz ione x1

(4 pin)

Tas t ie r a PS / 2 x 1

Mou s e PS/2 x 1

Porta seriale x1

Porta LAN x1

Porta USB x 4

Connettore audio x3

200 mm (larghezza) x 293 mm

(altez za)

Supporto RAID 0 / 1 / 0+1 / 5

Windows XP / Vista / 7

Alimentazione ventolina CPU (con funzione Smart

Fan)

Ciascun connettore supporta 2 porte USB

pannello frontale

Biostar si riserva il diritto di aggiungere o

rimuovere il supporto di qualsiasi sistema

operativo senza preavviso.

31

Motherboard Manual

SPANISH

Conector AM3

CPU

FSB

Conjunto de

chips

Súper E/S

Memoria

principal

IDE

SATA II

Red Local

Códecs de

sonido

Ranuras

Conectores

en p laca

Procesadores AMD Phenom II/ Athlon II

(Vatio máx imo: 95W )

Admite HyperTransport 2.0 con un ancho

de banda de hasta 2.0 GT/s

nVIDIA nForce 520

ITE 8718F

Le ofrece las funcionalidades heredadas de

us o más comú n Súper E /S.

Ranuras DIMM DDR3 x 4

Capacidad máxima de memoria de 16GB

Cada DIMM admite DDR de

512MB/1GB/2GB/4GB

Controlador IDE integrado

Controlador ATA Serie Integrado

Realtek RTL 8111DL

ALC662

Ranura PCI X3

Ranura PCI Express x16 X1

Ranura PCI express x 1 X1

Conector disco flexible X1 Cada conector soporta 2 unidades de disco flexible

Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora

Conector IDE X1 Cada conector soporta 2 dispositivos IDE

Especificación

La arquitectura AMD 64 permite el procesado de 32 y

64 bits

Soporta las tecnologías Hyper Transport 2.0

Interfaz de cuenta Low Pin

In iciat ivas d e cont rol d e entorno,

Monitor hardware

Controlador de velocidad de ventilador

Función "Guardia inteligente" de ITE

Módulo de memoria DDR3 de canal Doble

Admite DDR3 de 800 / 1066 / 1333

No admite DIMM registrados o DIMM compatibles con

ECC

Modo bus maestro Ultra DMA 33 / 66 / 100 / 133

Soporte los Modos PIO 0~4,

Tasas de transferencia de hasta 3 Gb/s.

Co mp at ible co n la ve rsión S ATA 2 .0.

Negociación de 10 / 100 / 1000 Mb/s

Funciones Half / Full dúplex

Salida de sonido de 5.1 canales

Soporte de sonido de Alta Definición

32

Panel

trasero de

E/S

Ta maño d e

la placa

NF520D3

Especificación

Conector SATA X4 Cada conector soporta 1 dispositivos SATA

Co nector de p ane l f ronta l X1 S oport a in s t a la c io nes en e l p anel f ront a l

Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal

Conector de salida S/PDIF X1

Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con

función Smart Fan)

Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de sistema

Cabecera de borrado de CMOS X1

Conector USB X2 Cada conector soporta 2 puertos USB frontales

Conector de alimentación X1

(24 patillas)

Conector de alimentación X1

(4 patillas)

Tec lad o P S /2 X1

Ratón PS/2 X1

Puert o serie X1

Puerto de red local X1

Puert o USB X4

Conector de sonido X3

200 mm. (A) X 293 mm. (H)

Funciones

especiales

Soporte de

sistema

operativo

Admite RAID 0 / 1 / 0+1 / 5

Windows XP / Vista / 7

Biostar se reserva el derecho de añadir o retirar el

soporte de cualquier SO con o sin aviso previo.

33

Motherboard Manual

PORTUGUESE

Socket AM3

CPU

FSB

Chipset

Especificaçã

o Super I/O

Memória

principal

IDE

SATA II

LAN

Codec de

som

Ranhuras

Conectores

na placa

Processadores AMD Phenom II/ Athlon II

(Watt máximo: 95W)

Suport a a tecno logia HyperTransport 2.0 com

uma largura de banda até 2.0 GT/s

nVIDIA nForce 520

ITE 8718F

Proporciona as funcionalidades mais

utilizadas em termos da especificação Super

I/O.

Ranhuras DIMM DDR3 x 4

Capacidad e máx ima de memó r ia: 16 GB

Cada módulo DIMM suporta uma memória

DDR3 de 512MB/ 1GB/2GB /4GB

Controlador IDE integrado

Controlador Serial ATA integrado

Realtek RTL 8111DL

ALC662

Ranhura PCI x3

Ranhura PCI Express x16 x1

Ranhura PCI Express x 1 x1

Conector da unidade de disquetes x1 Cada conector suporta 2 unidades de d isquetes

Conector da para impressora x1 Cada conector suporta 1 Porta para impressora

Conector IDE x1 Cada conector suporta 2 dispositivos IDE

ESPECIFICAÇÕES

A arquit ectura AMD 64 per mite uma co mputa ção de

32 e 64 bits

Suporta as t ecno logias Hyper Transport 2.0

Interface LPC (Low Pin Count).

In iciat ivas p ara con t ro lo d o a mb iente

Monitorização do hardware

Controlador da velocidade da ventoinha

Função "S mart Gu ardian" d a ITE

Módulo de memória DDR3 de canal duplo

Suporta módulos DDR3 800 / 1066 / 1333

Os módulos DIMM registados e os DIMM ECC não

são suportados

Modo Bus master U ltra DMA 33 / 66 / 100 / 133

Suporta o modo PIO 0~4,

Velocidades de transmissão de dados até 3 Gb/s.

Compat ib ilidad e co m a especif ica ção SATA versão

2.0.

Auto negociação de 10 / 100 / 1000 Mb/s

Capacidade semi/full-duplex

Saída de áudio de 5.1 canais

Suporta a especificação High-Definition Audio

34

Entradas/S

aídas no

painel

traseiro

Tamanho

da placa

Característi

cas

especiais

Sistemas

operativos

suportados

NF520D3

ESPECIFICAÇÕES

Conector SATA x4 Cada conector suporta 1 dispositivo SATA

Conector do painel frontal x1 Para suporte de várias funções no painel frontal

Conector de áud io frontal x1 Suporta a fun ção de áud io no paine l frontal

Conector de saída S/PDIF x1

Conector da ventoinha da CPU x1

Conector da ventoinha do sistema x1 Alimentação da vento inha do sistema

Conector para limpeza do CMOS x1

Conector USB x2

Conector de alimentação x1

(24 pinos)

Conector de alimentação x1

(4 p inos)

Tec lad o P S /2 x1

Rato PS/2 x1

Porta s ér ie x1

Porta LAN x1

Porta USB x4

Tomada de áudio x3

200 mm (L) X 293 mm (A)

Suporta as funções RA ID 0 / 1 / 0+1 / 5

Windows XP / Vista / 7

Alimentação da ventoinha da CPU (com a função

Smart Fan)

Cada conector suporta 2 portas USB no painel

frontal

A Biostar reserva-se o direito de adicionar ou

remover suporte para qualquer sistema operativo

com ou sem avis o prév io.

35

Motherboard Manual

POLISH

SPEC

Procesor

FSB

Chipset

Pamięć

główna

Super I/O

IDE

Socket AM3

AMD Phenom II/ Athlon II Procesory

(Maksymalny Watt: 95W)

Obsługa HyperTransport 2.0 o szerokości

pasma do 2.0 GT/s

nVIDIA nForce 520

Gniazda DDR3 DIMM x 4

Maks. wielkość pamięci 16GB

Każde gniazdo DIMM obs ługuje moduły

512MB/1GB/2GB/4GB DDR3

ITE 8718F

Zapewnia najbardziej powszechne funkcje

Super I/O.

Zintegrowany kontroler IDE

Architektura AMD 64 umożliwia przetwarzanie 32 i 64

bitowe

Obsługa Hyper Transport 2.0

Mod uł pamięci DDR3 z trybem podwójnego kanału

Obsługa DDR3 800 / 1066 / 1333

Brak obsług i Register ed DIMM oraz ECC D IMM

Interfejs Low Pin Count

Funkcje kontroli warunków pracy,

Mon itor H /W

Kontroler prędkości wenty lato ra

Funkcja ITE "Smart Guardian"

Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master

obsługa PIO tryb 0~4,

SATA II

LAN

Kodek

dźwiękowy

Gniazda

Złącza

wbud owane

36

Zintegrowany kontroler Serial ATA

Transfer danych do 3 Gb/s.

Zgodność ze specyfikacją SATA w wersj i 2. 0.

10 / 100 / 1000 Mb/s z automatyczną negocjacją s zyb kości

Realtek RTL 8111DL

Działanie w tryb ie połowicznego / pełnego dupleksu

5.1 kanałowe wyjście audio

ALC662

Obsługa H ig h-Def in it io n Aud io

Gniazdo PCI x3

Gniazdo PCI Express x16 x1

Gniazdo PCI Express x 1 x1

Złącze napędu dyskietek x1 Każde złącze o bs ługuje 2 napędy dyskietek

Złącze Port drukarki x1 Każde złącze o bs ługuje 1 Port drukarki

SPEC

Złącze IDE x1 Każde złącze obs ługuje 2 urządzenia IDE

Złącze SATA x4 Każde złącze obs ługuje 1 urządzenie SATA

Złącze panela przedniego x1 Obsługa elementów panela przedniego

Przedn ie złącze aud io x1 Obsługa funkcji audio na panelu przednim

Złącze wyjścia S/PDIF x1

NF520D3

Back Panel

I/O

Wymiary

płyty

Funkcje

specjalne

Złącze główkowe wentylatora procesora

Zasilanie wentylatora procesora (z funkcją Smart Fan)

x1

Złącze główkowe wenty lat ora

Zasilanie wentylatora systemowego

systemowego x1

Złącze główkowe kasowan ia CMOS x 1

Złącze USB x2 Każde złą cze obsługuje 2 porty USB na panelu przednim

Złącze zasilania (24 pinowe) x1

Złącze zas ilania (4 p ino we) x1

Klawiatura PS/2 x1

Mys z PS /2 x1

Port szeregowy x1

Port LAN x1

Port US B x4

Gniazdo audio x3

200 mm (S) X 293 mm (W)

Obsługa RAID 0 / 1 / 0 +1 / 5

Obsluga

systemu

operacyjne

go

Windows XP / Vista / 7

Biostar zastrzega sobie prawo dodawania lub

odwoływ ania obsług i dowolnego sys temu operacyjnego

bez powiadomienia.

37

Motherboard Manual

RUSSIAN

CPU

(центральн

ый

процессор)

FSB

Набо р

микросхем

Основная

память

Super I/O

IDE

SATA

Локальная

сеть

Звуко во й

кодек

Слоты

Встроенны

й разъём

Гнездо AM3

Процессоры AMD Phenom II/ Athlon II
(Максим ал ьн ый ватт: 95W )

Поддержка HyperTransport 2.0 с

пропускной способностью до 2.0 GT/s

nVIDIA nForce 520

Слоты DDR3 DIMM x 4

Максимальная ёмкос ть памяти 16 ГБ
Каждый модуль DIMM поддерживает

512МБ /1ГБ/2ГБ /4ГБ DDR3

ITE 8718F

Обеспечивает наиболее используемые

действующие фун кц ио н ал ьн ы е
возможности Super I/O.

Встроенное устройство упр авл ени я

Встроенное последовательное устройство

Realtek RTL 8111DL

ALC662

Слот PCI x3

Слот PCI Express x16 x1

Слот PCI Express x 1 x1

Разъ ём НГМ Д x1

Разъ ём Пор т подклю чения принтера x1

СПЕЦ

Арх итектур а A MD 64 разрешать обработка данных

на 32 и 64 бит
Поддержка Hyper Transport 2.0

Мод уль памяти с д вух кан альным режимом DDR3

Поддержка DDR3 800 / 1066 / 1333
Не поддерживает зарегистрированные модули

DIMM and ECC DIMM

Интерфейс с ни зким количество м выводов
Инициативы по охране окружающей среды,

Аппаратный монитор
Регул ятор скорости

Функц ия ITE "Smart Guard ian " (Интеллектуальная

защит а)

встроенными интерфейсами устр ойств

Режим "хозяина" шины Ultra D MA 3 3 / 66 / 1 00 /

133

Поддержка режима PIO 0~4,

упра вления ATA
скорость передачи данных до 3 гигабит/с.

Соответствие спецификации SATA версия 2.0.

Автоматическо е согл асован ие 10 / 100 / 1000 Мб /с

Частичная / полна я дуплексная способность

Звуко ва я поддержка High- Def in it io n

5.1канальный звуковой вых од

Каждый разъём поддерживает 2 накопителя на

гибких магнитных дисках

Каждый разъём поддерживает 1 По рт

подключения принтера

38

Задняя

панель

средств

ввода-выв

ода

Разм ер

панели

Специальн

ые

технически

е

характерис

тики

Поддержка

OS

NF520D3

СПЕЦ

Разъ ём IDE x 1

Разъ ём SATA x4 Каждый разъём поддерживает 1 ус тройс тво SATA

Разъ ём на лицевой панели x1 Поддержка устр ойств на лицевой панели

Входной звуковой разъём x1 Поддержка звуко вых функций на лицевой панели

Разъ ём вывода для S/PDIF x1

Контактирующее приспособление

вентил ятора центрального процессора x1

Контактирующее приспособление

вентил ятора системы x1

Открытое контактир ующ ее

приспособление CMOS x1

USB- разъём x2

Разъ ем питания (24 вы во д) x1

Разъ ем питания (4 вы вод) x1

Клавиатура PS/2 x1
Мышь PS/2 x1

Последоват ельны й порт x1

Пор т LAN x1
USB- порт x4

Гнездо для подключени я
наушников x3

200 мм (Ш) X 293 мм (В)

Поддержка RAID 0 / 1 / 0+1 / 5

Windows XP / Vista / 7

Каждый разъём поддерживает 2 встроенных
интерфейса накопителей

Источник пит ания для вентилято р а центрального

процессора (с функц и ей интеллектуального
вентил ятора)

Источник пит ания для вентилято р а системы

Каждый разъём поддерживает 2 USB-порта на

лицевой панели

Biostar сохраняет за собой право добавлять или

удаля ть средства обеспечения для OS с или без
предварительного уведомле ния.

39

Motherboard Manual

ARABIC

تﺎﻔﺻاﻮﻤﻟا

ﺔﻴﻨﻘﺗ ﻦﻜﻤﺗAMD 64 ﺔﻋﺮﺴﺏ ﺔﻴﺏﻮﺳﺎﺤﻟ ا تﺎﻴﻠﻤﻌﻟا ءاﺮﺝإ 32 و64 ﺖﺏ

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyper Transpo rt و 2.0

عﻮﻥ ﻦﻡ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR3 تﺎﻌﺳ 800 / 1066 / 1333ﺖﻳﺎﺏ ﺎﺠﻴﻡ

ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ ﻻDIMM ﻊﻡ ﻖﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠﺗو ECC

ﺔﻔﻴﻇو"S mart Gu ard ian" ﻦﻡ IT E

ﺔﻴﻨﻘ ﺘﺏ ﻞﻗﺎﻥUltra DMA 33 / 66 / 100 / 133

ةﺮآاذ ةﺪﺣوDDR3 ﻘﻟا ﺔﺝودﺰﻡﺎﻨة

ﻞﺋﺎﺳو ﻢﻜﺤﺘﻟا ﻲﻓ ﺔﺌﻴﺒﻟا:

ﺐﻗاﺮﻡ ﺔﻓﺮﻌﻤﻟ ﺔﻟ ﺎﺣ ةﺰﻬﺝﻷا

ﺐﻗاﺮﻡ ﻲﻓ ﺔﻋﺮﺳ ﺔﺣوﺮﻤﻟا

ﻊﺿو ﻲﺴﻴﺋر

ﻊﺿو ﻢﻋدPIO Mode 0~4

تﺎﺠﻟﺎﻌﻡAMD Phenom II/ Athlon II

(طاو ىﻮﺼﻗ: 95و)

ﻢﻋﺪﺗ ﻨﻘﺗﺔﻴ HyperTransport ددﺮﺘﺏ ﻞﺼﻳ ﻰﻟإ2.0 2.0

nVIDIA nForce 520

ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ16 ﺖﻳﺎﺏ ﺎﺠﻴﺝ

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM عﻮﻥ ﻦﻡ ةﺮآاذ ﻢﻋﺪﺗ DDR3 ﺔﻌﺳ

ﺮﻓﻮﺗ ﺔﻔﻴﻇو Super I/O ﺮﺜآﻷا ًﺎ ﻡ ا ﺪ ﺨ ﺘ ﺳا.

ﺗﻢﻋﺪ ﺔﻴﻨﻘ ﺗ Low Pi n Count Interface

ﻢﻜﺤﺘﻡ ID E ﻞﻡﺎﻜﺘﻡ

ﺲﺒﻘﻡAM3

ةﺪﺣو ﺔﺠﻟﺎﻌﻤﻟا

ﺔﻳﺰآﺮﻤﻟا

ﻞﻗﺎﻨﻟا ﻲﻡﺎﻡﻷا ﻲﺒﻥﺎﺠﻟا

GT/s

ﺔﻋﻮﻤﺠﻡ ﺢﺋاﺮﺸﻟا

ﺔﺤﺘﻓDDR3 DIM M دﺪﻋ4

ةﺮآاﺬﻟا ﺔﻴﺴﻴﺋﺮﻟا

/512 ﺎﺠﻴﻡ

و ﺖﻳﺎﺏ1/و 2/و 4 ﺎﺠﻴﺝﺖﻳﺎﺏ

ITE 8718F

Super I/O

ﺬﻔﻨﻣ IDE

40

ﺔﻘﺏﺎﻄﻡ تﺎﻔﺻاﻮﻤﻟ SATA راﺪﺻﻹا 2.0.

ضوﺎﻔﺗ ﻲﺋﺎﻘﻠﺗ 10/100 ﺎﺠﻴﻣ ﺖیﺎﺑ /ﺔﻴﻥ ﺎﺛ و1ﺎﺠﻴﺝ ﺖﺑ/ﺔﻴﻥﺎﺛ

ﻞﻡﺎﻜﻟا جودﺰﻤﻟا ﻞﻘﻨﻟا ﺔﻴﻥﺎﻜﻡإ/ﻲﻔﺼﻨﻟا

5.1 تاﻮﻨﻗ جﺮﺨﻟ تﻮﺼﻟا

5.1 تاﻮ ﻨﻗ جﺮﺨﻟ تﻮﺼﻟا

ﻞﻘﻥ تﺎﻥﺎﻴﺒﻟا تﺎ ﻋﺮﺴﺏ ﻞﺼﺗ ﻰﻟإ 3 ﺖﺏﺎﺠﻴﺝ/ﺔﻴﻥﺎ ﺙ.

ﻢﻜﺤﺘﻡ Serial ATA ﻞﻡﺎﻜﺘﻡ

Realtek RTL 8111DL

ALC662

SATA II

ﺔﻜﺒﺵ ﺔﻴﻠﺥاد

ﻚﻳدﻮآ تﻮﺼﻟا

ﺔﺤﺘﻓPCI دﺪﻋ3

تﺎﺤﺘﻔﻟا

ﺔﺤﺘﻓx16 PCI Express دﺪﻋ1

ﺔﺤﺘﻓPCI Express x 1 دﺪﻋ1

ﺔﻥﺮﻡ صاﺮﻗأ كﺮﺤﻡ ﺬﻔﻨﻡ دﺪﻋ1 ﺔﻥﺮﻤﻟا صاﺮﻗﻸﻟ ﻦﻴآ ﺮﺤﻡ ﻢﻋﺪﻳ

ﺔﻌﺏﺎﻃ ﺬﻔﻨﻡ دﺪﻋ1

ﺬﻓﺎﻨﻤﻟا ﻰﻠﻋ ﺢﻄﺳ

ﺔﺣﻮﻠﻟا

NF520D3

تﺎﻔﺻاﻮﻤﻟا

ﺬﻔﻨﻡIDE دﺪﻋ1 ةﺰﻬﺝأ ﻦﻡ ﻦﻴﻨﺙا ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪﻳIDE

ﺬﻔﻨﻡSATA دﺪﻋ4 ةﺰﻬﺝأ ﻦﻡ ﺪﺣاو ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪﻳSATA

ﺔﻴﻡﺎﻡﻷا ﺔﺣﻮﻠﻟا ﺬﻔﻨﻡ دﺪﻋ1 ﻋﺪﻳﺔﻴﻡﺎﻡﻷا ﺔﺣﻮﻠﻟا تاﺰﻴﻬﺠﺗ ﻢ

ﻲﻡﺎﻡﻷا تﻮﺼﻟا ﺬﻔﻨﻡ دﺪﻋ1 ﺔﻴﻡﺎﻡﻷا ﺔﺣﻮﻠﻟ ﺎﺏ تﻮﺼﻟا ﺔﻔﻴﻇو ﻢﻋﺪﻳ

جﺮﺥ ﺬﻔﻨﻡS/PDIF دﺪﻋ1

ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻡ ﺔﻠﺻو دﺪﻋ1 ﺔﻔﻴﻇو ﻊﻡ ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺘﻟSmart Fan

مﺎﻈﻨﻟا ﺔﺣوﺮﻡ ﺔﻠﺻو دﺪﻋ1 ﻟا ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺘﻟمﺎﻈﻨ

ﺢﺴﻡ ﺔﻠﺻوCMOS دﺪﻋ1

ﺬﻔﻨﻡUS B دﺪﻋ2 ﻲﺘﺤ ﺘﻓ ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪﻳUSBﺔﻴﻡﺎﻡﻷا ﺔﺣﻮﻠﻟﺎﺏ

ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺗ ﺬﻔﻨﻡ)24سﻮﺏد( دﺪﻋ1

ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺗ ﺬﻔﻨﻡ)4ﺲﻴﺏﺎﺏد( دﺪﻋ1

ﺢﻴﺗﺎﻔﻡ ﺔﺣﻮﻟPS/2 دﺪﻋ1

سوﺎﻡ PS/2 دﺪﻋ1

ﻲﻠﺴﻠﺴﺗ ﺬﻔ ﻨﻡ دﺪﻋ1

ﺔﻜﺒﺵ ﺬﻔﻨﻡﺔﻴﻠﺤﻡ لﺎﺼﺗا دﺪﻋ1

ﺬﻓﺎﻨﻡUS B دﺪ ﻋ4

تﻮﺻ ﺲﺒﻘﻡ دﺪﻋ3

ﻢﻋﺪﺗ ﺔﻴﻨﻘﺗ RAID 0 / 1 / 0 +1 / 5

200 ﻢﻡ)ضﺮﻋ (X 293 ﻢﻡ)عﺎﻔﺗرا(

ﺬﻓﺎﻨﻡ ﻞﺥد/جﺮﺥ

ﺔﺣﻮﻠﻟا ﺔﻴﻔﻠﺨﻟا

ﺎﻳاﺰﻡ ﺔﺻﺎﺥ

ﻢﺠﺣ ﺔﺣﻮﻠﻟا

ﻆﻔﺘﺤﺗ Biostar ﺎﻬﻘﺤﺏ ﻲﻓ ﺔﻓﺎﺿإ وأ ﺔﻟاز إ ﻢﻋﺪﻟا يﻷ مﺎﻈﻥ ﻞﻴﻐﺸﺗ رﺎﻄﺥﺈﺏ وأ ﺪﺏنو

رﺎﻄﺥإ.

Windows XP / Vista / 7

ﻢﻋد ﺔﻤ ﻈﻥأ ﻞﻴﻐﺸﺘﻟا

41

Motherboard Manual

JAPANESE

仕様

CPU

FSB

チップセット

メインメモリ

Super I/O

IDE

Socket AM3

AMD Phenom II/ Athlon II プロセッ サ

(最高 のワット : 95W )

2.0 GT/sのバンド 幅まで ハイパート ランスポ

ート2.0をサポ ートします

nVIDIA nForce 520

DDR3 DIMMスロット x 4

最大メモリ容 量16GB

各DIMMは 512MB/1GB/2GB/4GB DDR3を

サポート

ITE 8718F

もっとも一般 に使 用されるレ ガシーSuper I/O

機能を採用し てい ます。

統合ID Eコントローラ

AMD 64アーキ テクチャで は、32ビットと64ビット計算が可

能です

ハイパートラ ンス ポート2.0サポートします

デュアル チ ャン ネルモードDDR3メモリモジ ュール

DDR3 800 / 1066 / 1333 をサポ ート

登録済みDIMMとECC DIMMはサポ ートされま せん

低ピンカウン トイ ンターフェ イス

環境コントロ ール イニシアチ ブ、

H/Wモニ ター

ファン速度コ ント ローラ/ モニター

ITE の「スマート ガー ディアン」 機能

Ultra DMA 33 / 66 / 100 / 133バスマ スタ モード

PIO Mode 0~4のサポート 、

SATA II

LAN

サウンド

Codec

スロット

オンボードコ

ネクタ

42

統合シリアルATA コントロー ラ

最高3 Gb/秒の データ転送 速度

SATAバージョン2.0仕様に準拠。

10 / 100 / 1000 Mb/秒のオ ートネゴシ エーション

Realtek RTL 8111DL

半/全二重機能

5.1チャンネル オーディオ アウ ト

ALC662

ハイデフィニ ショ ンオーディ オのサポー ト

PCIスロット x3

PCI Express x16スロット x1

PCI Express x 1スロット x1

フロッピーコ ネク タ x1 各コネクタは 2つのフロ ッピードラ イブを サポートし ます

プリンタポー トコ ネクタ x1 各コネクタは 1つのプリ ンタポート をサポート します

NF520D3

仕様

IDE コネクタ x1 各コネクタは2つのID Eデバ イスを サポートし ます

SATAコネクタ x4 各コネ クタは 1つのSATAデバイスをサポ ートします

フロントパネ ルコ ネクタ x1 フロントパネ ル機 能をサポー トします

フロントオー ディ オコネクタ x1 フロントパネルオ ーディ オ機能をサ ポートしま す

S/PDIFアウトコネ クタ x1

CPUファンヘッダ x1 CPUファン電源装置(スマートフ ァン機能を 搭載 )

システムファ ンヘ ッダ x1 システムファ ン電 源装置

CMOSクリアヘッダ x1

背面パネル

I/O

ボードサイズ

特殊機能

OSサポー ト

USBコネク タ x2

各コネクタは 2つのフロ ントパネル USBポートをサ ポート し

ます

電源コネクタ (24 ピン) x1

電源コネクタ (4ピン) x1

PS/2キーボード x1

PS/2マウス x1

シリアルポー ト x1

LANポート x1

USBポート x4

オーディオジ ャッ ク x3

200 mm (幅) X 293 mm (高さ )

RAID 0 / 1 / 0+1 / 5 の サポー ト

Biostarは事前の サポートな しにOSサ ポー トを追加ま たは削

Windows XP / Vista / 7

除する権利を 留保 します。

2009/12/07

43