Behringer 172 Quick Start Guide
Quick Start Guide
SYSTEM 100
172 PHASE SHIFTER/
DEL AY/ LFO
Legendary Analog Phase Shifter/
Delay/LFO Module for Eurorack
Controls
(3)
(1)
(2)
(8)
(9)
(10)
(11)
(1) CV IN – Accept s voltage from an e xternal sourc e to
control o r modulate the phase s hifter frequ ency or audio
delay time. If n o jack is inserte d the LFO can be used to
modulate t he eect.
(2 ) MOD INTENSIT Y – Controls how much th e eect is
modulate d by the LFO or exter nal CV input.
(3 ) EFFEC T ON/OFF – Engages or disengages the
eect section.
(4 ) SHIF T FREQ – Adjusts the fre quency of the pha se shifter.
(5 ) SIG IN – Acc epts an incoming sig nal via 3.5 mm TS cable.
(6 ) SIG OU T – Sends the signal fr om the eect se ction.
(5)(4)
(6)
(7)
(12)
(13)
(14)
(7 ) RESONANCE – Adj usts the amount of s ignal that is fed
back through the eect.
(8 ) DEL AY TIME – Adjusts the tim e of the delay eec t.
(9 ) FREQUENC Y – Controls the LFO out put frequenc y.
(10) LFO OUT – Sends t he LFO signal as a trian gle and inverted
triangle w ave.
(11) THRESHOLD – Controls the i nput voltage level r equired to
trigger t he gate.
(12 ) GATE IN – Accepts an inco ming gate signal via 3.5 mm
TS cable.
(13 ) GATE OUT – Send the ga te delay signal via 3.5 mm
TS cable.
(14) GATE TIME – Controls th e gate length.
Power Connection
The modul e comes with the req uired power cable f or connecting
to a standa rd Eurorack power su pply system. Fol low these
steps to con nect power to the mo dule. It is easier to make
these con nections bef ore the module has be en mounted into
a rack cas e.
1. Turn the power supp ly or rack case power o and
disconne ct the power cabl e.
2. Ins ert the 16-pin conn ector on the power c able into the
socket on t he power supply or rac k case. The connec tor has
a tab that wi ll align with the gap in t he socket, so it can not
be inser ted incorrec tly. If the power supply d oes not have
a keyed socke t, be sure to orient pi n 1 (-12 V) with the red
stripe o n the cable.
3. Ins ert the 10-pin co nnector into the s ocket on the back of
the modul e. The connector ha s a tab that will align wi th the
socket fo r correct ori entation.
4. Af ter both ends of the po wer cable have been se curely
attac hed, you may mount the mo dule in a case and tur n on
the power supply.
Installation
The neces sary screws ar e included with th e module for mount ing
in a Eurorac k case. Connect t he power cable bef ore mounting.
Dependi ng on the rack case, th ere may be a series of xed holes
spaced 2 HP ap art along the leng th of the case, or a tr ack that
allows indi vidual threaded p lates to slide along th e length
of the cas e. The free-movi ng threaded plate s allow precise
positio ning of the module, bu t each plate should be p ositioned in
the approx imate relation to th e mounting holes in yo ur module
before a ttaching the sc rews.
Hold the mo dule against the Eur orack rails so that e ach of the
mounting h oles are aligned wi th a threaded rail o r threaded
plate. Att ach the screws par t way to start, w hich will allow
small adjus tments to the pos itioning while you g et them all
aligned. After the nal position has been established, tighten the
screws d own.
Specications
Inputs
Phase shifter signal input
Type 3.5 mm TS jack, AC coupled
Impedance 70 kΩ, unbalanced
Max input level +16 dBu
Phase shifter CV input
Type 3.5 mm TS jack, DC coupled
Impedance >50 kΩ, unbalanced
Max input level +10 V
CV range 0 V to +10 V
Audio delay signal input
Type 3.5 mm TS jack, AC coupled
Impedance 15 kΩ, unbalanced
Max input level +20 dBu
Audio delay CV input
Type 3.5 mm TS jack, DC coupled
Impedance >70 kΩ, unbalanced
Max input level +10 V
CV range 0 V to +10 V
Gate input
Type 3.5 mm TS jack, DC coupled
Impedance 47 kΩ, unbalanced
Max input level +10 V
CV range 0 V to +10 V
Outputs
Phase shifter signal output
Type 3.5 mm TS jack, DC coupled
Impedance 1 kΩ, unbalanced
Max output level +18 dBu
Audio delay signal output
Type 3.5 mm TS jack, DC coupled
Impedance 1 kΩ, unbalanced
Max output level +16 dBu
LFO output
Type 2 x 3.5 mm TS jacks, DC coupled
Impedance 1.2 kΩ
Max output level 10 V p-p
Gate output
Type 3.5 mm TS jack, DC coupled
Impedance 500 Ω
Max output level +5 V
Controls
Phase shifter eect switch O / on
Phase shifter mod intensity -∞ to unity gain
Phase Shift frequency 200 Hz to 8 kHz
Phase shifter resonance O to maximum resonance
Audio delay eect switch O / on
Audio delay mod intesity -∞ to unity gain
Audio delay time 1 ms to 7 ms
Audio delay resonance O to maximum resonance
LFO frequency 0.02 Hz to 10 Hz
Gate Threshold 0.3 V to 5 V
Gate delay time 0.3 ms to 6 s
Gate time 0.3 ms to 6 s
Power
Power supply Eurorack
Current draw 60 mA (+12 V), 60 mA (-12 V)
Physical
Dimensions 44 x 81 x 129 mm
Rack units 16 HP
Weight 0.19 kg (0.42 lbs)
(1.7 x 3.2 x 5.1")
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and
other information are subject to change without notice. All trademarks are the
property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake,
Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone
and Coolaudio are trademarks or registered trademarks of Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2020 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.
Loading...