BECKHOFF CB1061 User Manual

CB1061

Manual

rev 1.1

Beckhoff Automation GmbH & Co. KG phone: +49 (0) 52 46/963-0 Eiserstr. 5 fax: +49 (0) 52 46/963-198 33415 Verl email: info@beckhoff.de Germany web: www.beckhoff.de

Contents

0 Document History................................................................................................................................. 7

1 Introduction .......................................................................................................................................... 8

1.1 Notes on the Documentation ........................................................................................................ 8

1.1.1 Liability Conditions ................................................................................................................ 8

1.1.2 Copyright ............................................................................................................................... 8

1.2 Safety Instructions ........................................................................................................................ 9

1.2.1 Disclaimer ............................................................................................................................. 9

1.2.2 Description of Safety Symbols ............................................................................................ 10

1.3 Essential Safety Measures ......................................................................................................... 11

1.3.1 Operator's Obligation to Exercise Diligence ....................................................................... 11

1.3.2 National Regulations Depending on the Machine Type ..................................................... 11

1.3.3 Operator Requirements ...................................................................................................... 11

1.4 Functional Range ........................................................................................................................ 12

2 Overview ............................................................................................................................................ 13

2.1 Features ...................................................................................................................................... 13

2.2 Specifications and Documents ................................................................................................... 15

3 Connectors ......................................................................................................................................... 17

3.1 Power Supply, System Connectors, CPU .................................................................................. 18

3.1.1 Power Supply ...................................................................................................................... 18

3.1.2 System ................................................................................................................................ 20

3.1.3 CPU Socket ........................................................................................................................ 21

3.1.4 CMOS Battery ..................................................................................................................... 22

3.2 Back Panel Connectors .............................................................................................................. 23

3.2.1 DVI Connectors................................................................................................................... 23

3.2.2 DVI/HDMI ............................................................................................................................ 25

3.2.3 Display Port ......................................................................................................................... 26

3.2.4 PS/2 Keyboard and Mouse ................................................................................................. 27

3.2.5 Serial Interface COM1 ........................................................................................................ 28

3.2.6 USB and LAN...................................................................................................................... 29

3.2.7 Audio Connectors ............................................................................................................... 31

3.3 SATA and Memory ..................................................................................................................... 32

3.3.1 SATA Interfaces .................................................................................................................. 32

3.3.2 Memory ............................................................................................................................... 33

3.4 Internal Connectors .................................................................................................................... 36

3.4.1 USB 5-14 ............................................................................................................................ 36

3.4.2 Serial ports COM2 to COM4 ............................................................................................... 38

3.4.3 CD-In ................................................................................................................................... 39

3.4.4 S/PDIF ................................................................................................................................ 40

3.4.5 PCI interfaces ..................................................................................................................... 41

3.4.6 PCI-express Interfaces (x1) ................................................................................................ 43

3.4.7 PCI-express interface (x4) .................................................................................................. 44

3.4.8 PCI-express interface (x16) ................................................................................................ 46

3.4.9 SMB/I2C .............................................................................................................................. 47

3.4.10 GPIO ................................................................................................................................... 48

3.4.11 Fan Connectors .................................................................................................................. 49

3.5 Jumper Settings .......................................................................................................................... 50

Beckhoff New Automation Technology CB1061 page 3

Contents

3.5.1 Clear CMOS ........................................................................................................................ 50

3.5.2 Jumper: Keyboard Power (KBPWR)................................................................................... 51

4 BIOS Settings ..................................................................................................................................... 52

4.1 General Remarks ........................................................................................................................ 52

4.2 Main ............................................................................................................................................ 53

4.3 Advanced .................................................................................................................................... 55

4.3.1 PCI Subsystem Settings ..................................................................................................... 57

4.3.2 ACPI Settings...................................................................................................................... 59

4.3.3 Trusted Computing ............................................................................................................. 60

4.3.4 CPU Configuration .............................................................................................................. 61

4.3.5 SATA Configuration ............................................................................................................ 64

4.3.6 AMT Configuration .............................................................................................................. 67

4.3.7 Power Controller Options .................................................................................................... 69

4.3.8 USB Configuration .............................................................................................................. 71

4.3.9 Super IO Configuration ....................................................................................................... 72

4.3.10 H/W Monitor ........................................................................................................................ 74

4.3.11 Serial Port Console Redirection.......................................................................................... 76

4.3.12 Network Stack ..................................................................................................................... 79

4.3.13 Intel(R) Ethernet Connection I218-LM ................................................................................ 80

4.3.14 Intel(R) I210 Gigabit Network Connection .......................................................................... 82

4.3.15 Driver Health ....................................................................................................................... 84

4.4 Chipset ........................................................................................................................................ 86

4.4.1 PCH-IO Configuration ......................................................................................................... 87

4.4.2 System Agent (SA) Configuration ....................................................................................... 94

4.5 Boot ........................................................................................................................................... 104

4.5.1 CSM16 Parameters .......................................................................................................... 106

4.5.2 CSM Parameters .............................................................................................................. 107

4.6 Security ..................................................................................................................................... 108

4.6.1 Secure Boot Menu ............................................................................................................ 109

4.7 Save & Exit ............................................................................................................................... 112

4.8 BIOS-Update ............................................................................................................................ 113

5 Mechanical Drawings ....................................................................................................................... 114

5.1 PCB: Mounting Holes ............................................................................................................... 115

5.2 PCB: Pin 1 Dimensions ............................................................................................................ 116

5.3 PCB: Die Center ....................................................................................................................... 117

6 Technical Data ................................................................................................................................. 118

6.1 Electrical Data ........................................................................................................................... 118

6.2 Environmental Conditions ......................................................................................................... 118

6.3 Thermal Specifications ............................................................................................................. 119

7 Support and Service ........................................................................................................................ 120

7.1 Beckhoff's Branch Offices and Representatives ...................................................................... 120

7.2 Beckhoff Headquarters ............................................................................................................. 120

7.2.1 Beckhoff Support .............................................................................................................. 120

7.2.2 Beckhoff Service ............................................................................................................... 120

I Annex: Post-Codes .......................................................................................................................... 122

II Annex: Resources ............................................................................................................................ 123

IO Range .............................................................................................................................................. 123

Memory Range ..................................................................................................................................... 123

page 4 Beckhoff New Automation Technology CB1061

Contents

Interrupt ................................................................................................................................................ 123

PCI Devices .......................................................................................................................................... 124

SMB Devices ........................................................................................................................................ 124

Beckhoff New Automation Technology CB1061 page 5

Chapter: Document History Notes on the Documentation

page 6 Beckhoff New Automation Technology CB1061

Notes on the Documentation Chapter: Document History

Version

Changes

0.1

first pre-release

0.2

SATA port enumeration corrected

1.0

first released version. Chapter 3.4.8 corrected, chapter 3.2.6 LAN pinout corrected

1.1

Chapter 3.4.9 corrected connector direction

0 Document History

NOTE

All company names, brand names, and product names referred to in this manual are registered or unregistered trademarks of their respective holders and are, as such, protected by national and international law.

Beckhoff New Automation Technology CB1061 page 7

Chapter: Introduction Notes on the Documentation

1 Introduction

1.1 Notes on the Documentation

This description is only intended for the use of trained specialists in control and automation engineering who are familiar with the applicable national standards. It is essential that the following notes and explanations are followed when installing and commissioning these components.

1.1.1 Liability Conditions

The responsible staff must ensure that the application or use of the products described satisfy all the requirements for safety, including all the relevant laws, regulations, guidelines and standards. The documentation has been prepared with care. The products described are, however, constantly under development. For that reason the documentation is not in every case checked for consistency with performance data, standards or other characteristics. None of the statements of this manual represents a guarantee (Garantie) in the meaning of § 443 BGB of the German Civil Code or a statement about the contractually expected fitness for a particular purpose in the meaning of § 434 par. 1 sentence 1 BGB. In the event that it contains technical or editorial errors, we retain the right to make alterations at any time and without warning. No claims for the modification of products that have already been supplied may be made on the basis of the data, diagrams and descriptions in this documentation.

1.1.2 Copyright

© This documentation is copyrighted. Any reproduction or third party use of this publication, whether in whole or in part, without the written permission of Beckhoff Automation GmbH & Co. KG, is forbidden.

page 8 Beckhoff New Automation Technology CB1061

Safety Instructions Chapter: Introduction

1.2 Safety Instructions

Please consider the following safety instructions and descriptions. Product specific safety instructions are to be found on the following pages or in the areas mounting, wiring, commissioning etc.

1.2.1 Disclaimer

All the components are supplied in particular hardware and software configurations appropriate for the application. Modifications to hardware or software configurations other than those described in the documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG.

Beckhoff New Automation Technology CB1061 page 9

Chapter: Introduction Safety Instructions

1.2.2 Description of Safety Symbols

The following safety symbols are used in this documentation. They are intended to alert the reader to the associated safety instructions.

ACUTE RISK OF INJURY!

If you do not adhere to the safety advise next to this symbol, there is immediate danger to life and health of individuals!

RISK OF INJURY!

If you do not adhere to the safety advise next to this symbol, there is danger to life and health of individuals!

HAZARD TO INDIVIDUALS, ENVIRONMENT, DEVICES, OR DATA!

If you do not adhere to the safety advise next to this symbol, there is obvious hazard to individuals, to environment, to materials, or to data.

NOTE OR POINTER

This symbol indicates information that contributes to better understanding.

page 10 Beckhoff New Automation Technology CB1061

Essential Safety Measures Chapter: Introduction

1.3 Essential Safety Measures

1.3.1 Operator's Obligation to Exercise Diligence

The operator must ensure that

o the product is only used for its intended purpose o the product is only operated in sound condition and in working order o the instruction manual is in good condition and complete, and always available for reference at the

location where the products are used

o the product is only used by suitably qualified and authorised personnel o the personnel is instructed regularly about relevant occupational safety and environmental protection

aspects

o the operating personnel is familiar with the operating manual and in particular the safety notes

contained herein

1.3.2 National Regulations Depending on the Machine Type

Depending on the type of machine and plant in which the product is used, national regulations governing the controllers of such machines will apply, and must be observed by the operator. These regulations cover, amongst other things, the intervals between inspections of the controller. The operator must initiate such inspections in good time.

1.3.3 Operator Requirements

o Read the operating instructions All users of the product must have read the operating instructions for the system they work with. o System know-how All users must be familiar with all accessible functions of the product.

Beckhoff New Automation Technology CB1061 page 11

Chapter: Introduction Functional Range

1.4 Functional Range

NOTE

The descriptions contained in the present documentation represent a detailed and extensive product description. As far as the described motherboard was acquired as an integral component of an Industrial PC from Beckhoff Automation GmbH & Co. KG, this product description shall be applied only in limited scope. Only the contractually agreed specifications of the corresponding Industrial PC from Beckhoff Automation GmbH & Co. KG shall be relevant. Due to several models of Industrial PCs, variations in the component placement of the motherboards are possible. Support and service benefits for the built-in motherboard will be rendered by Beckhoff Automation GmbH & Co. KG exclusively as specified in the product description (inclusive operation system) of the particular Industrial PC.

page 12 Beckhoff New Automation Technology CB1061

Features Chapter: Overview

Intel® Q87 PCH

4x SoDIMM204

DDR3L-1600

(dual channel)

MEMORY

Power VCCCore; VTT;

DDRVTT, GFXVCC

BIOS

SATA0-5

RealTek®

ALC889

HDA Link

USB3-10, 13, 14

DP

1.5/3/6GB

Intel®

i210

SMBus

SPI

USB 2.0

SMSC®

SCH3114

LINE i/o

CD IN

MIC

SPDIF i/o

Intel®

i218

PCIe

DVI/HDMI

CRT

LPC

PCI Slot 1

Intel® Core™

i3 / i5 / i7

FDI

DMI

PCIe(PEG)

KB MS I2C

FAN1-4

COM1-4

8x GPIO

PCIe to PCI

Bridge

PI7C9X111SL

PCI

PCI Slot 2

PCI Slot 3

LAN 2

LAN 1

PCIe x4 Slot 1

PCIe x1 Slot 2

PCIe x1 Slot 3

(n/a if x4 dev. In sl. 1)

USB 3.0USB1,2,11,12

Trusted

Platform

Module

SPI

2 Overview

2.1 Features

The CB1061 is a computer motherboard for industrial applications. Complying to the ATX form factor and based on Intel®'s Q87 PCH chipset, it is equipped with an LGA1150 CPU socket for Intel® CPUs of the 4th Generation Core™- and Celeron®- families. Modern DDR3 technology provides top-notch memory performance, accommodating up to 32 GByte of RAM (DDR3L-1600) via SO-DIMM204. Expansion cards can be added into three PCI slots, two PCIeX1 slots, one PCIeX4 slot and one PCIeX16 slots. The CB1061 also offers a wide range of internal and external connectors, such as four serial ports, two LAN connectors, 14 USB channels, six SATA connectors offering up to 6Gb/s, digital and analogue audio, VGA/DVI/HDMI connectors, DisplayPort connector, LCD connector, etc.

In addition the board serves via the integrated Trusted Platform Module as Trusted Computing Platform and provides essential safety functions.

o Socket LGA1150 o Suitable CPUs: Intel® Core™ i3 / i5 / i7 o Chipset Intel® Q87 PCH o Two SO-DIMM204 sockets for up to 32 GByte DDR3L-1600 RAM o Three PCI sockets o Two PCIe-x1 sockets o One PCIe-x4 socket o One PCIe-x16 socket o Four serial interfaces COM1 to COM4 o Two LAN interfaces Ethernet 10/100/1000 (Base-T) o Six SATA channels (up to 6Gb/s transfer rate) o PS2 keyboard / mouse interface o 10 USB 2.0 interfaces

Beckhoff New Automation Technology CB1061 page 13

Chapter: Overview Features

o 4 USB 3.0 interfaces o BIOS AMI® Aptio o 1x DVI-I o 1x DVI-D, 1x internal HDMI (can't be used simultaneously) o CRT connection o HDA compatible sound controller with SPDIF in and out o GPIO o RTC with external CMOS battery o ATX power connector incl. 2x2pin 12V connector o Format: ATX (305mm x 220mm)

page 14 Beckhoff New Automation Technology CB1061

Specifications and Documents Chapter: Overview

2.2 Specifications and Documents

In making this manual and for further reading of technical documentation, the following documents, specifications and web-pages were used and are recommended.

 ATX Specification

Version 2.2

www.formfactors.com

 PCI Specification

Version 2.3 resp. 3.0

www.pcisig.com

 PCI Express® Base Specification

Version 2.0

www.pcisig.com

 ACPI Specification

Version 5.0

www.acpi.info

 ATA/ATAPI Specification

Version 7 Rev. 1

www.t13.org

 USB Specifications

www.usb.org

 SM-Bus Specification

Version 2.0

www.smbus.org

 Intel® Chipset Description

Intel® 8 Series Chipset datasheet

www.intel.com

 Intel® Chip Description

4th Gen. Intel® Core™ Processor Family Mobile datasheet

www.intel.com

 Intel® Chip Description

i218 Datasheet

www.intel.com

 Intel® Chip Description

i210 Datasheet

www.intel.com

 SMSC® Chip Description

SCH3114 Datasheet

www.smsc.com

(NDA required)

 Realtek® Chip Description

ALC885/889 Datasheet

www.realtek.com.tw

 ICS® Chip Description

ICS9LPRS501 Datasheet

www.idt.com

Beckhoff New Automation Technology CB1061 page 15

Chapter: Overview Specifications and Documents

 American Megatrends®

Aptio™ Text Setup Environment (TSE) User Manual

www.ami.com

 American Megatrends®

Aptio™ 4.x Status Codes

www.ami.com

page 16 Beckhoff New Automation Technology CB1061

Specifications and Documents Chapter: Connectors

3 Connectors

This section describes all the connectors found on the CB1061.

NOTICE

For most interfaces, the cables must meet certain requirements. For instance, USB 2.0 requires twisted and shielded cables to reliably maintain full speed data rates. Restrictions on maximum cable length are also in place for many high speed interfaces and for power supply. Please refer to the respective specifications and use suitable cables at all times.

Beckhoff New Automation Technology CB1061 page 17

Chapter: Connectors Power Supply, System Connectors, CPU

Description

Name

Description

3.3 volt supply

3.3V

1

13

3.3V

3.3 volt supply

3.3V

2

14

-12V

12 volt supply

ground

GND

3

15

GND

ground

5 volt supply

VCC

4

16

PS_ON

ground

GND

5

17

GND

ground

5 volt supply

VCC

6

18

GND

ground

GND

7

19

GND

ground

ATX Powergood

PWRGOOD

8

20

-5V

volt supply -5V

standby supply 5V

SVCC

9

21

VCC

5 volt supply

12 volt supply

12V

10

22

VCC

5 volt supply

12 volt supply

12V

11

23

VCC

5 volt supply

3.3 volt supply

3.3V

12

24

GND

ground

3.1 Power Supply, System Connectors, CPU

3.1.1 Power Supply

The connector for the power supply is a 2x12pin ATX connector ("ATX24", Amphenol MF42-SD-24LK). It is accompanied by a 2x2pin connector, which must be used to provide the COREIN power supply.

Pinout "ATX24" power connector:

page 18 Beckhoff New Automation Technology CB1061

Power Supply, System Connectors, CPU Chapter: Connectors

Description

Name

Description

ground

GND

1 3 COREIN

12 volt supply

ground

GND

2 4 COREIN

12 volt supply

Pinout ATX power connector 2x2:

Beckhoff New Automation Technology CB1061 page 19

Chapter: Connectors Power Supply, System Connectors, CPU

Description

Name

Description

on/suspend button

PWRBTN#

A1

B1

GND

ground

GND

A2

B2

N/C

reserved

N/C

A3

B3

PWLED#

power LED

ground

GND

A4

B4

N/C

reserved

5 volt supply

VCC

A5

B5

PWLED

3.3 volt supply

harddisk LED

HDLED#

A6

B6

N/C

reserved

5 volt supply

VCC

A7

B7

VCC

5 volt supply

reserved

N/C

A8

B8

GND

ground

IrDA transmit

IRTX

A9

B9

N/C

reserved

ground

GND

A10

B10

BEEP

speaker

reserved

N/C

A11

B11

N/C

reserved

N/C

A12

B12

GND

ground

5 volt supply

VCC

A13

B13

RESET#

reset

3.1.2 System

Typical signals for system control are provided through a 2x13 IDC socket connector (Samtec TSW-113-07-S-D) with a spacing of 2.54mm. This connector combines signals for power button, reset, keyboard lock and several LEDs.

Pinout IDC socket connector "System 1":

page 20 Beckhoff New Automation Technology CB1061

Power Supply, System Connectors, CPU Chapter: Connectors

3.1.3 CPU Socket

The CB1061 board has an LGA1150 CPU socket accomodating certain versions of Intel®'s 4th

generation Core™ architecture CPUs. The LGA1150 is a socket, in which the processor is inserted and

subsequently gets fixed by using the clamping bracket. There is only one orientation in which the processor will fit into the socket. Once the processor is in place, the clamping bracket must be fixed to ensure proper electrical contact.

ATTENTION

In case of improper insertion of the processor contacts can bend and therefore be damaged.

NOTE

Processors must be ordered separately. The board ships without a CPU.

Beckhoff New Automation Technology CB1061 page 21

Chapter: Connectors Power Supply, System Connectors, CPU

Name

Description

1

BATT

battery 3.3 volt

2

GND

ground

3.1.4 CMOS Battery

The board ships with a CR2032 battery holder (Renata VBH2032-1) and 3V battery. Alternatively, an external battery can be connected via a 2pin connector (JST B2B-EH-A, mating connector: EHR-2).

page 22 Beckhoff New Automation Technology CB1061

Back Panel Connectors Chapter: Connectors

Name

Description

1

TMDSDAT2#

DVI data 2 -

2

TMDSDAT2

DVI data 2 +

3

GND

ground

4

N/C

reserved

5

N/C

reserved

6

DDC CLK

DDC clock (DVI/VGA)

7

DDC DAT

DDC data (DVI/VGA)

8

VSYNC

VGA vertical sync

9

TMDSDAT1#

DVI data 1 -

10

TMDSDAT1

DVI data 1 +

11

GND

ground

12

N/C

reserved

13

N/C

reserved

14

VCC

5 volt supply

15

GND

ground

16

HP_DETECT

hot plug detect

17

TMDSDAT0#

DVI data 0 -

18

TMDSDAT0

DVI data 0 +

19

GND

ground

20

N/C

reserved

3.2 Back Panel Connectors

The board complies with the ATX form factor and thus honours the "I/O Connector Area" as defined in the ATX specification. A range of standard connectors are available: You can connect PS/2 keyboard and mouse, displays, speakers, microphone, LAN, USB etc. If the board is mounted in a normal ATX compliant case, these connectors are located on the back side of the case.

3.2.1 DVI Connectors

The CB1061 has one DVI-I connector and one DVI-D connector combined in one component (Foxconn QH11121-DADF-4F). With an appropriate adapter, you can connect a CRT display to the DVI-I connector. Digital DVI or HDMI displays can be attached to both connectors. The CPU's graphics system supports up to two independent displays.

Pinout DVI-I:

Beckhoff New Automation Technology CB1061 page 23

Chapter: Connectors Back Panel Connectors

Name

Description

21

N/C

reserved

22

GND

ground

23

TMDS CLK

DVI clock

24

TMDS CLK#

DVI clock

C1

RED

VGA red

C2

GREEN

VGA green

C3

BLUE

VGA blue

C4

HSYNC

VGA horizontal sync

C5

GND

ground

Name

Description

1

TMDSDAT2#

DVI data 2 -

2

TMDSDAT2

DVI data 2 +

3

GND

ground

4

N/C

reserved

5

N/C

reserved

6

DDC CLK

DDC clock (DVI/VGA)

7

DDC DAT

DDC data (DVI/VGA)

8

N/C

reserved

9

TMDSDAT1#

DVI data 1 -

10

TMDSDAT1

DVI data 1 +

11

GND

ground

12

N/C

reserved

13

N/C

reserved

14

VCC

5 volt supply

15

GND

ground

16

HP_DETECT

hot plug detect

17

TMDSDAT0#

DVI data 0 -

18

TMDSDAT0

DVI data 0 +

19

GND

ground

20

N/C

reserved

21

N/C

reserved

22

GND

ground

23

TMDS CLK

DVI clock +

24

TMDS CLK#

DVI clock -

C1

N/C

reserved

C2

N/C

reserved

C3

N/C

reserved

C4

N/C

reserved

C5

GND

ground

Pinout DVI-D:

page 24 Beckhoff New Automation Technology CB1061

Back Panel Connectors Chapter: Connectors

Description

Name

Description

HDMI panel detected

HPD_SINK

1 2 N/C

reserved

SMBus clock (DDC)

SCL_SINK

3 4 SDA_SINK

SMBus dat (DDC)

5 volt supply

VCC

5 6 GND

ground

GND

7 8 TMDS_CLK#

DVI clock -

DVI data 0 -

TMDS_D0#

9

10

TMDS_CLK

DVI clock +

DVI data 0 +

TMDS_D0

11

12

GND

ground

GND

13

14

TMDS_D1#

DVI data 1 -

DVI data 2 -

TMDS_D2#

15

16

TMDS_D1

DVI data 1 +

DVI data 2 +

TMDS_D2

17

18

GND

ground

3.2.2 DVI/HDMI

The CB1061 provides a second DVI interface which is realized as a 2x9pin header (Molex 87831-1820, mating connector e.g. Molex 0791098658-ND). Analog VGA is not available on this connector. However, an HDMI device can be connected. This connector and the DVI-D connector cannot be used simultaneously.

Pinout 2x9pin connector DVI/HDMI:

Beckhoff New Automation Technology CB1061 page 25

Chapter: Connectors Back Panel Connectors

Description

Name

Description

displayport lane 0 +

DPL0

1 2 GND

ground

displayport lane 0 -

DPL0#

3 4 DPL1

displayport lane 1 +

ground

GND

5 6 DPL1#

displayport lane 1 -

displayport lane 2 +

DPL2

7 8 GND

ground

displayport lane 2 -

DPL2#

9

10

DPL3

displayport lane 3 +

ground

GND

11

12

DPL3#

displayport lane 3 -

ground

GND

13

14

GND

ground

displayport aux +

DPAUX

15

16

GND

ground

displayport aux -

DPAUX#

17

18

HPD

hotplug detect

ground

GND

19

20

3.3V

3.3V supply

3.2.3 Display Port

For DisplayPort devices, a suitable standard connector is available (Foxconn 3VD11203-D7AB-4H).

Pinout DisplayPort connector:

page 26 Beckhoff New Automation Technology CB1061

Back Panel Connectors Chapter: Connectors

Description

Name

Description

mouse data

MDAT

B1

B2

N/C

reserved

ground

GND

B3

B4

(S)VCC

5 volt supply

mouse clock

MCLK

B5

B6

N/C

reserved

Description

Name

Description

keyboard data

KDAT

A1

A2

MDAT

mouse data

ground

GND

A3

A4

(S)VCC

5 volt supply

keyboard clock

KCLK

A5

A6

MCLK

mouse clock

3.2.4 PS/2 Keyboard and Mouse

PS/2 mice and keyboards are connected via standard mini-DIN connectors. If you want to use the keyboard or mouse to wake up the board from standby or suspend mode you have to activate this functionality by adjusting the KBPWR jumper settings (page 51). With this jumper you can switch from normal power supply (VCC) to standby power supply (SVCC) for keyboard/mouse. Some relevant settings will have to be adjusted in BIOS setup.

Pinout PS/2 mouse:

Pinout PS/2 keyboard:

Beckhoff New Automation Technology CB1061 page 27

Chapter: Connectors Back Panel Connectors

Description

Name

Description

data carrier detect

DCD

1 6 DSR

data set ready

receive data

RXD

2 7 RTS

request to send

transmit data

TXD

3 8 CTS

clear to send

data terminal ready

DTR

4 9 RI

ring indicator

ground

GND

5

3.2.5 Serial Interface COM1

The serial interface COM1 is made available via a 9-pin standard DSUB-connector (male, e.g. FCI 75869-301LF). Signal level is RS232. The port address and the interrupt are set via the BIOS setup.

Pinout serial port (DSUB connector):

page 28 Beckhoff New Automation Technology CB1061

Back Panel Connectors Chapter: Connectors

Name

Description

1

VCC

5 volt for USBX

2

USBX#

minus channel USBX

3

USBX

plus channel USBX

4

GND

ground

Name

Description

1

VCC

5 volt for USBX

2

USBX#

Minus channel USBX

3

USBX

Plus channel USBX

4

GND

ground

5

StdA_SSRX-

SuperSpeed Receiver -

6

StdA_SSRX+

SuperSpeed Receiver +

7

GND

ground

8

StdA_SSTX-

SuperSpeed Transmitter -

9

StdA_SSTX+

SuperSpeed Transmitter +

3.2.6 USB and LAN

To save space USB and LAN connectors are provided in the form of combo connectors. These either comprise two USB connectors or two USB connectors and one LAN connector. This way all board variants provide four external USB channels. USB channels 3 and 4 support USB 2.0, furthermore USB 1 and 2 support USB 3.0. You may note that the setting of USB keyboard or USB mouse support in the BIOS-setup is only necessary and advisable, if the OS offers no USB-support. BIOS-setup can be changed with a USB keyboard without enabling USB keyboard support. Running Windows with these features enabled may lead to significant performance or functionality limitations. The 2.0 USB interface provides up to 500 mA current, the 3.0 USB interface provides up to 900mA. All USB interfaces are protected by an electronically resettable fuse. The board comes in different variants, some with one Gigabit-LAN connector, others with two. All LAN connectors support 10/100/1000 Ethernet with automatic bandwith selection. Controller chips are the LynxPoint (MAC) accompanied by the i218 (PHY, LAN1) and, if present, the i210(MAC/PHY, LAN2).

Pinout USB connector for channel X:

Pinout USB3.0 connector for channel X:

Beckhoff New Automation Technology CB1061 page 29

Chapter: Connectors Back Panel Connectors

Name

Description

1

LAN2-0

LAN2 channel 0 plus

2

LAN2-0#

LAN2 channel 0 minus

3

LAN2-1

LAN2 channel 1 plus

4

LAN2-2

LAN2 channel 2 plus

5

LAN2-2#

LAN2 channel 2 minus

6

LAN2-1#

LAN2 channel 1 minus

7

LAN2-3

LAN2 channel 3 plus

8

LAN2-3#

LAN2 channel 3 minus

Pinout LAN 10/100/1000:

page 30 Beckhoff New Automation Technology CB1061

Back Panel Connectors Chapter: Connectors

3.2.7 Audio Connectors

Line-in, line-out, and microphone signals are provided in the form of three 3,5mm-TRS-connectors.

Beckhoff New Automation Technology CB1061 page 31

Chapter: Connectors SATA and Memory

Name

Description

1

GND

ground

2

SATATX

SATA transmit +

3

SATATX#

SATA transmit -

4

GND

ground

5

SATARX

SATA receive -

6

SATARX#

SATA receive +

7

GND

ground

3.3 SATA and Memory

3.3.1 SATA Interfaces

The CB1061 provides six SATA interfaces. They all support transfer rates of 1,5GB/s up to 6GB/s.

Pinout SATA:

page 32 Beckhoff New Automation Technology CB1061

SATA and Memory Chapter: Connectors

Description

Name

Description

memory reference current

REF-DQ

1 2 GND

ground

GND

3 4 DQ4

data 4

data 0

DQ0

5 6 DQ5

data 5

data 1

DQ1

7 8 GND

ground

GND

9

10

DQS0#

data strobe 0 -

data mask 0

DM0

11

12

DQS0

data strobe 0 +

ground

GND

13

14

GND

ground

data 2

DQ2

15

16

DQ6

data 6

data 3

DQ3

17

18

DQ7

data 7

ground

GND

19

20

GND

ground

data 8

DQ8

21

22

DQ12

data 12

data 9

DQ9

23

24

DQ13

data 13

ground

GND

25

26

GND

ground

data strobe 1 -

DQS1#

27

28

DM1

data mask 1

data strobe 1 +

DQS1

29

30

RESET#

Reset

ground

GND

31

32

GND

ground

data 10

DQ10

33

34

DQ14

data 14

data 11

DQ11

35

36

DQ15

data 15

ground

GND

37

38

GND

ground

data 16

DQ16

39

40

DQ20

data 20

data 17

DQ17

41

42

DQ21

data 21

ground

GND

43

44

GND

ground

data strobe 2 -

DQS2#

45

46

DM2

data mask 2

data strobe 2 +

DQS2

47

48

GND

ground

GND

49

50

DQ22

data 22

data 18

DQ18

51

52

DQ23

data 23

3.3.2 Memory

The CB1061 is equipped with four SO-DIMM204 sockets for DDR3L-1600-RAM. For technical and mechanical reasons it is possible that particular memory modules cannot be employed. Please ask your distributor for recommended memory modules With currently available memory modules a memory extension up to 32 GByte is possible. All timing parameters for different memory modules are automatically set by BIOS.

Pinout SO-DIMM204:

Beckhoff New Automation Technology CB1061 page 33

Chapter: Connectors SATA and Memory

Description

Name

Description

data 19

DQ19

53

54

GND

ground

GND

55

56

DQ28

data 28

data 24

DQ24

57

58

DQ29

data 29

data 25

DQ25

59

60

GND

ground

GND

61

62

DQS3#

data strobe 3 -

data mask 3

DQM3

63

64

DQS3

data strobe 3 +

ground

GND

65

66

GND

ground

data 26

DQ26

67

68

DQ30

data 30

data 27

DQ27

69

70

DQ31

data 31

ground

GND

71

72

GND

ground

clock enables 0

CKE0

73

74

CKE1

clock enables 1

1.5 volt supply

1.5V

75

76

1.5V

1.5 volt supply

reserved

N/C

77

78

(A15)

reserved

SDRAM bank 2

BA2

79

80

A14

address 14

1.5 volt supply

1.5V

81

82

1.5V

1.5 volt supply

address 12 (burst chop)

A12/BC#

83

84

A11

address 11

address 9

A9

85

86

A7

address 7

1.5 volt supply

1.5V

87

88

1.5V

1.5 volt supply

address 8

A8

89

90

A6

address 6

address 5

A5

91

92

A4

address 4

1.5 volt supply

1.5V

93

94

1.5V

1.5 volt supply

address 3

A3

95

96

A2

address 2

address 1

A1

97

98

A0

address 0

1.5 volt supply

1.5V

99

100

1.5V

1.5 volt supply

Clock 0 +

CK0

101

102

CK1

clock 1 +

Clock 0 -

CK0#

103

104

CK1#

clock 1 -

1.5 volt supply

1.5V

105

106

1.5V

1.5 volt supply

address 10 (auto precharge)

A10/AP

107

108

BA1

SDRAM bank 1

SDRAM Bank 0

BA0

109

110

RAS#

row address strobe

1.5 volt supply

1.5V

111

112

1.5V

1.5 volt supply

write enable

WE#

113

114

S0#

chip select 0

column address strobe

CAS#

115

116

ODT0

on die termination 0

1.5 volt supply

1.5V

117

118

1.5V

1.5 volt supply

address 13

A13

119

120

ODT1

on die termination 1

Chip Select 1

S1#

121

122

N/C

reserved

1.5 volt supply

1.5V

123

124

1.5V

1.5 volt supply

reserved

(TEST)

125

126

REF-CA

reference current

ground

GND

127

128

GND

ground

data 32

DQ32

129

130

DQ36

data 36

data 33

DQ33

131

132

DQ37

data 37

ground

GND

133

134

GND

ground

data strobe 4 -

DQS4#

135

136

DQM4

data mask 4

data strobe 4 +

DQS4

137

138

GND

ground

GND

139

140

DQ38

data 38

data 34

DQ34

141

142

DQ39

data 39

data 35

DQ35

143

144

GND

ground

GND

145

146

DQ44

data 44

data 40

DQ40

147

148

DQ45

data 45

data 41

DQ41

149

150

GND

ground

GND

151

152

DQS5#

data strobe 5 -

data mask 5

DQM5

153

154

DQS5

data strobe 5 +

ground

GND

155

156

GND

ground

data 42

DQ42

157

158

DQ46

data 46

data 43

DQ43

159

160

DQ47

data 47

ground

GND

161

162

GND

ground

page 34 Beckhoff New Automation Technology CB1061

SATA and Memory Chapter: Connectors

Description

Name

Description

data 48

DQ48

163

164

DQ52

data 52

data 49

DQ49

165

166

DQ53

data 53

ground

GND

167

168

GND

ground

data strobe 6 -

DQS6#

169

170

DQM6

data mask 6

data strobe 6

DQS6

171

172

GND

ground

GND

173

174

DQ54

data 54

data 50

DQ50

175

176

DQ55

data 55

data 51

DQ51

177

178

GND

ground

GND

179

180

DQ60

data 60

data 56

DQ56

181

182

DQ61

data 61

data 57

DQ57

183

184

GND

ground

GND

185

186

DQS7#

data strobe 7 -

data mask 7

DQM7

187

188

DQS7

data strobe 7 +

ground

GND

189

190

GND

ground

data 58

DQ58

191

192

DQ62

data 62

data 59

DQ59

193

194

DQ63

data 63

ground

GND

195

196

GND

ground

SPD address 0

SA0

197

198

EVENT#

Event

3.3 volt supply

3.3V

199

200

SDA

SMBus data

SPD address 1

SA1

201

202

SCL

SMBus clock

termination current

VTT

203

204

VTT

termination current

Beckhoff New Automation Technology CB1061 page 35

Chapter: Connectors Internal Connectors

Description

Name

Description

5 volt for USBx

VCC

1 2 VCC

5 volt for USBy

minus channel USBx

USBx#

3 4 USBy#

minus channel USBy

plus channel USBx

USBx

5 6 USBy

plus channel USBy

ground

GND

7 8 GND

ground

reserved

N/C

9

10

N/C

reserved

Name

Description

1

VCC

5 volt for USBX

2

USBX#

Minus channel USBX

3

USBX

Plus channel USBX

4

GND

ground

5

StdA_SSRX-

SuperSpeed Receiver -

6

StdA_SSRX+

SuperSpeed Receiver +

7

GND

ground

8

StdA_SSTX-

SuperSpeed Transmitter -

3.4 Internal Connectors

3.4.1 USB 5-14

The USB channels 5 to 10 and 13/14 are provided via four 2x5 pin connectors (FCI 75869-301LF, mating connector FCI 71600-610LF). The USB channels 11 and 12 are provided via a 2x10 pin connector (FCI 10075025-F01-20ALF, mating connector FCI 90311-020LF). The USB channels 5 to 10 and 13/14 support USB2.0. Furthermore the USB channels 11 and 12 support USB3.0.

You may note that the setting of USB keyboard or USB mouse support in the BIOS-setup is only necessary and advisable, if the OS offers no USB-support. BIOS-setup can be changed with a USB keyboard without enabling USB keyboard support. Running Windows with these features enabled may lead to significant performance or functionality limitations.

Every USB interface provides up to 900 mA (500mA for USB2.0) current and is protected by an electronically resettable fuse.

Pinout 2x5 pin connector USB x/y:

Pinout USB3.0 connector for channel X:

page 36 Beckhoff New Automation Technology CB1061

Internal Connectors Chapter: Connectors

Name

Description

9

StdA_SSTX+

SuperSpeed Transmitter +

Beckhoff New Automation Technology CB1061 page 37

Chapter: Connectors Internal Connectors

Description

Name

Description

data carrier detect

DCD

1 2 DSR

data set ready

receive data

RXD

3 4 RTS

request to send

transmit data

TXD

5 6 CTS

clear to send

data terminal ready

DTR

7 8 RI

ring indicator

ground

GND

9

10

VCC

5 volt supply

3.4.2 Serial ports COM2 to COM4

The three serial ports COM2 to COM4 are made available via a 2x5 pin connector each (FCI 75869-301LF, mating connector FCI 71600-610LF). Signals are RS232. The port address and the interrupt are set via the BIOS setup.

Pinout COM connector:

page 38 Beckhoff New Automation Technology CB1061

Internal Connectors Chapter: Connectors

Name

Description

1

CD_L

CD left channel

2

CD_GND

CD ground

3

CD_GND

CD ground

4

CD_R

CD right channel

3.4.3 CD-In

In addition to the external TRS connectors mentioned above, the CB1061 offers an internal 4 pin connector (Foxconn HF1104E-P1), providing customers with even more possibilities to connect audio devices (analogue signals).

Pinout CD-in connector:

Beckhoff New Automation Technology CB1061 page 39

Chapter: Connectors Internal Connectors

Description

Name

Description

ground

GND

1 2 SPDIFO

SPDIF out

3.3 volt supply

3,3V

3 4 VCC

5 volt supply

ground

GND

5 6 SPDIFI

SPDIF in

3.4.4 S/PDIF

For digital audio signals an SPDIF interface is available, which can be accessed using an internal 2x3 pin IDC socket connector with a spacing of 2,54mm.

Pinout SPDIF connector:

page 40 Beckhoff New Automation Technology CB1061

Internal Connectors Chapter: Connectors

Description

Name

Description

test logic reset

TRST#

A1

B1

-12V

-12 volt supply

12 volt supply

12V

A2

B2

TCK

test clock

test mde select

TMS

A3

B3

GND

ground

test data input

TDI

A4

B4

TDO

test data output

5 volt supply

VCC

A5

B5

VCC

5 volt supply

interrupt A

INTA#

A6

B6

VCC

5 volt supply

interrupt C

INTC#

A7

B7

INTB#

interrupt B

5 volt supply

VCC

A8

B8

INTD#

interrupt D

reserved

N/C

A9

B9

GND

ground

5 volt supply

VCC

A10

B10

N/C

reserved

N/C

A11

B11

GND

ground

GND

A12

B12

GND

ground

GND

A13

B13

GND

ground

3.3 volt supply

3.3VAux

A14

B14

N/C

reserved

PCI reset

PRST#

A15

B15

GND

ground

5 volt supply

VCC

A16

B16

PCLK

clock

grant PCI use

GNT#

A17

B17

GND

ground

GND

A18

B18

REQ#

request

power management event

PME#

A19

B19

VCC

5 volt supply

address/data 30

AD30

A20

B20

AD31

address/data 31

3.3 volt supply

3.3V

A21

B21

AD29

address/data 29

address/data 28

AD28

A22

B22

GND

ground

address/data 26

AD26

A23

B23

AD27

address/data 27

ground

GND

A24

B24

AD25

address/data 25

3.4.5 PCI interfaces

There are three standard PCI slots available on the CB1061.

NOTE

Please note that due to the nature of the PCI bus some signals in the following table are different from one PCI slot to the other. This applies to the test signals (A4, B4), the interrupt signals (A6, A7, B7, B8), the clock signal (B16), the grant signal (A17), the request signal (B18), and the ID-select signal (A26).

Pinout PCI slot:

Beckhoff New Automation Technology CB1061 page 41

Chapter: Connectors Internal Connectors

Description

Name

Description

address/data 24

AD24

A25

B25

3.3V

3.3 volt supply

init device select

IDSEL

A26

B26

CBE3#

command, byte enable 3

3.3 volt supply

3.3V

A27

B27

AD23

address/data 23

address/data 22

AD22

A28

B28

GND

ground

address/data 20

AD20

A29

B29

AD21

address/data 21

ground

GND

A30

B30

AD19

address/data 19

address/data 18

AD18

A31

B31

3.3V

3.3 volt supply

address/data 16

AD16

A32

B32

AD17

address/data 17

3.3 volt supply

3.3V

A33

B33

CBE2#

command, byte enable 2

cycle frame

FRAME#

A34

B34

GND

ground

GND

A35

B35

IRDY#

initiator ready

Target Ready

TRDY#

A36

B36

3.3V

3.3 volt supply

ground

GND

A37

B37

DEVSEL#

device select

stop request by target

STOP#

A38

B38

GND

ground

3.3 volt supply

3.3V

A39

B39

PLOCK#

lock bus

SMBus clock PCI

SMBCLK

A40

B40

PERR#

parity error

SMBus data PCI

SMBDAT

A41

B41

3.3V

3.3 volt supply

ground

GND

A42

B42

SERR#

system error

parity

PAR

A43

B43

3.3V

3.3 volt supply

address/data 15

AD15

A44

B44

CBE1#

command, byte enable 1

3.3 volt supply

3.3V

A45

B45

AD14

address/data 14

address/data 13

AD13

A46

B46

GND

ground

address/data 11

AD11

A47

B47

AD12

address/data 12

ground

GND

A48

B48

AD10

address/data 10

address/data 9

AD9

A49

B49

GND

ground

coded

N/C

A50

B50

N/C

coded

N/C

A51

B51

N/C

coded

command, byte enable 0

CBEO#

A52

B52

AD8

address/data 8

3.3 volt supply

3.3V

A53

B53

AD7

address/data 7

address/data 6

AD6

A54

B54

3.3V

3.3 volt supply

address/data 4

AD4

A55

B55

AD5

address/data 5

ground

GND

A56

B56

AD3

address/data 3

address/data 2

AD2

A57

B57

GND

ground

address/data 0

AD0

A58

B58

AD1

address/data 1

5 volt supply

VCC

A59

B59

VCC

5 volt supply

reserved

N/C

A60

B60

VCC

5 volt supply

VCC

A61

B61

VCC

5 volt supply

VCC

A62

B62

VCC

5 volt supply

page 42 Beckhoff New Automation Technology CB1061

Internal Connectors Chapter: Connectors

Description

Name

Description

hot plug detect 1

PRSNT1#

A1

B1

12V

12 volt supply

12V

A2

B2

12V

12 volt supply

12V

A3

B3

N/C

reserved

ground

GND

A4

B4

GND

ground

reserved

N/C

A5

B5

SMBCLK

SMBus clock PCIe

reserved

N/C

A6

B6

SMBDAT

SMBus data PCIe

reserved

N/C

A7

B7

GND

ground

reserved

N/C

A8

B8

3.3V

3.3 volt supply

3.3V

A9

B9

N/C

reserved

3.3 volt supply

3.3V

A10

B10

S3.3V

3.3V standby-supply

PCIe reset

PERST#

A11

B11

PEWAKE#

link reactivation

ground

GND

A12

B12

N/C

reserved

reference clock +

REFCLK

A13

B13

GND

ground

reference clock -

REFCLK#

A14

B14

PET0

transmit lane 0 +

ground

GND

A15

B15

PET0#

transmit lane 0 -

receive lane 0 +

PER0

A16

B16

GND

ground

receive lane 0 -

PER0#

A17

B17

PRSNT2#

hot plug detect 2

ground

GND

A18

B18

GND

ground

3.4.6 PCI-express Interfaces (x1)

The CB1061 board has two slots for PCIe-x1 expansion cards.

NOTE

When the motherboard PCIe-x4 slot (page 44) is occupied with a x4 device, then x1 slot 2 is de-activated.

NOTE

Please note that some signals in the following table are different from one PCIe slot to the other. This applies to the clock signals (A13, A14), the receive signals (A16, A17), and the transmit signals (B14, B15).

Pinout PCI-express-x1 connector:

Beckhoff New Automation Technology CB1061 page 43

Chapter: Connectors Internal Connectors

Description

Name

Description

hot plug detect 1

PRSNT1#

A1

B1

12V

12V supply

12V

A2

B2

12V

12V supply

12V

A3

B3

N/C

reserved

ground

GND

A4

B4

GND

ground

reserved

N/C

A5

B5

SMBCLK

SMBus clock PCIe

reserved

N/C

A6

B6

SMBDAT

SMBus data PCIe

reserved

N/C

A7

B7

GND

ground

reserved

N/C

A8

B8

3,3V

3.3V supply

3,3V

A9

B9

N/C

reserved

3.3V supply

3,3V

A10

B10

S3,3V

3.3V standby

PCIe reset

PERST#

A11

B11

PEWAKE#

link reactivation

ground

GND

A12

B12

N/C

reserved

reference clock +

REFCLK

A13

B13

GND

ground

reference clock -

REFCLK#

A14

B14

PET0

transmit lane 0 +

ground

GND

A15

B15

PET0#

transmit lane 0 -

receive lane 0 +

PER0

A16

B16

GND

ground

receive lane 0 -

PER0#

A17

B17

PRSNT2#

hot plug detect 2

ground

GND

A18

B18

GND

ground

reserved

N/C

A19

B19

PET1

transmit lane 1 +

ground

GND

A20

B20

PET1#

transmit lane 1 -

receive lane 1 +

PER1

A21

B21

GND

ground

receive lane 1 -

PER1#

A22

B22

GND

ground

GND

A23

B23

PET2

transmit lane 2 +

ground

GND

A24

B24

PET2#

transmit lane 2 -

receive lane 2 +

PER2

A25

B25

GND

ground

receive lane 2 -

PER2#

A26

B26

GND

ground

3.4.7 PCI-express interface (x4)

The CB1061 has one slot for PCIe-x4 expansion cards. This slot also accomodates x1 expansion cards.

NOTE

When the slot is occupied with an x4 device, PCIe-x1 slot 2 (s. p. 43) is de-activated.

Pinout PCI-express-x1 connector:

page 44 Beckhoff New Automation Technology CB1061

Internal Connectors Chapter: Connectors

Description

Name

Description

ground

GND

A27

B27

PET3

transmit lane 3 +

ground

GND

A28

B28

PET3#

transmit lane 3 -

receive lane 3 +

PER3

A29

B29

GND

ground

receive lane 3 -

PER3#

A30

B30

N/C

reserved

ground

GND

A31

B31

PRSNT2#

hot plug detect 2

reserved

N/C

A32

B32

GND

ground

Beckhoff New Automation Technology CB1061 page 45

Chapter: Connectors Internal Connectors

Description

Name

Description

hot plug detect 1

PRSNT1#

A1

B1

12V

12 volt supply

12V

A2

B2

12V

12 volt supply

12V

A3

B3

N/C

reserved

ground

GND

A4

B4

GND

ground

reserved

N/C

A5

B5

SMBCLK

SMBus clock PCIe

reserved

N/C

A6

B6

SMBDAT

SMBus data PCIe

reserved

N/C

A7

B7

GND

ground

reserved

N/C

A8

B8

3.3V

3.3 volt supply

3.3V

A9

B9

N/C

reserved

3.3 volt supply

3.3V

A10

B10

S3.3V

3.3V standby-supply

PCIe reset

PERST#

A11

B11

PEWAKE#

link reactivation

ground

GND

A12

B12

N/C

reserved

reference clock +

REFCLK

A13

B13

GND

ground

reference clock -

REFCLK#

A14

B14

PET0

transmit lane 0 +

ground

GND

A15

B15

PET0#

transmit lane 0 -

receive lane 0 +

PER0

A16

B16

GND

ground

receive lane 0 -

PER0#

A17

B17

PRSNT2#

hot plug detect 2

ground

GND

A18

B18

GND

ground

3.4.8 PCI-express interface (x16)

One slot for PCI-express-x16-cards makes the expansion options on the CB1061 complete. You can use this slot for PCIe-x16 graphic adapters. This slot also acommodates x1 or x4 expansion cards.

NOTE

Please note that some signals in the following table are different from one PCIe slot to the other. This applies to the clock signals (A13, A14), the receive signals (A16, A17), and the transmit signals (B14, B15).

Pinout PCI-express-x1 connector:

page 46 Beckhoff New Automation Technology CB1061

Internal Connectors Chapter: Connectors

Description

Name

Description

3.3 volt supply

3.3V

1 6 GND

ground

SMBus clock

SMBCLK

2 7 SMBDAT

SMBus data

SMBus alarm

SMBALRT#

3 8 SVCC

standby supply 5V

I2C bus clock

I2CLK

4 9 I2DAT

I2C bus data

5 volt supply

VCC

5

10

GND

ground

3.4.9 SMB/I2C

The CB1061 can communicate with external devices via the SMBus protocol or the I2C protocol. The signals for these protocols are available through a 2x5 pin connector (JST B10B-PHDSSLFSN, mating connector: PHDR-10VS). The SMBus signals are processed by the chipset, the I2C signals are processed by the SIO unit.

Pinout SMBus/I2C connector:

Beckhoff New Automation Technology CB1061 page 47

Chapter: Connectors Internal Connectors

Description

Name

Description

5 volt supply

VCC

1

11

VCC

5 volt supply

GP input/output 10

GPIO10

2

12

N/C

reserved

GP input/output 11

GPIO11

3

13

N/C

reserved

GP input/output 12

GPIO12

4

14

N/C

reserved

GP input/output 13

GPIO13

5

15

N/C

reserved

GP input/output 14

GPIO14

6

16

N/C

reserved

GP input/output 15

GPIO15

7

17

N/C

reserved

GP input/output 16

GPIO16

8

18

N/C

reserved

GP input/output 17

GPIO17

9

19

N/C

reserved

ground

GND

10

20

GND

ground

3.4.10 GPIO

The General Purpose Input/Output interface is made available through a 2x10 pin connector (JST B20B-PHDSSLFSN, mating connector: PHDR-20VS). To make use of this interface the SIO unit must be programmed accordingly. Please refer to your distributor for information on available software support.

page 48 Beckhoff New Automation Technology CB1061

Internal Connectors Chapter: Connectors

Name

Description

1

GND

ground

2

12V

12 volt supply regulated

3

TACHO

fan monitoring signal

3.4.11 Fan Connectors

Four 3 pin connectors are available for attaching external 12V fans. All connectors except FAN4 can monitor fan speed. For this to work the fans must provide a corresponding speed signal.

Pinout fan connector:

NOTE

The FAN4 connector doesn't have pin 3 connected (N/C).

Beckhoff New Automation Technology CB1061 page 49

Chapter: Connectors Jumper Settings

3.5 Jumper Settings

3.5.1 Clear CMOS

In case the board doesn't start up anymore and BIOS setup is inaccessible there is a "last resort": You can use the "Clear CMOS" jumpers to reset all CMOS settings to factory defaults. In order to do so you need to shut down the computer, change the jumper settings from normal (pins 1 & 2 short) to "Clear CMOS" (pins 2 & 3 short) first on jumper Clear CMOS 1 and then on jumper Clear CMOS 2, wait a few seconds, put the jumpers back into normal position and reboot.

CAUTION

In order to avoid an undefined system state it is essential to ensure that the shorting of jumper Clear CMOS 1 (J1800) takes place BEFORE and only combined with the shorting of jumper Clear CMOS 2 (J1801).

Furthermore please notice, that if you reset the CMOS this does not only bring all settings made in BIOS setup back to default values, it also clears the date and time information stored in CMOS. So don't forget that, after the Clear CMOS procedure, you will have to set the clock again.

page 50 Beckhoff New Automation Technology CB1061

Jumper Settings Chapter: Connectors

3.5.2 Jumper: Keyboard Power (KBPWR)

Power supply for keyboard and mouse can be provided in two different ways, either using normal power supply VCC or standby power supply SVCC. You can switch between the two by using the KBPWR jumper. For VCC you need to short pins 1 and 2, for SVCC please short pins 2 and 3.

Beckhoff New Automation Technology CB1061 page 51

Chapter: BIOS Settings General Remarks

4 BIOS Settings

4.1 General Remarks

In each setup page, standard values for all setup entries can be loaded. Previously saved settings are loaded by pressing F2 and factory defaults are loaded with F3. Both F2 and F3, and also F4 ("Save & Exit") always affect the whole set of setup entries.

Setup entries starting with a „►" sign represent submenus. Navigation between entries is done using the

arrow keys on the keyboard, with the <Enter> key being used to select an entry, which either opens up a dialog box or opens a whole new submenu of setup entries. Each setup entry has a short help text associated with it. This is displayed in the upper right hand corner of the screen.

NOTICE

BIOS features and setup options are subject to change without notice. The settings displayed in the screenshots on the following pages are meant to be examples only. They do not represent the recommended settings or the default settings. Determination of the appropriate settings is dependent upon the particular application scenario in which the board is used.

page 52 Beckhoff New Automation Technology CB1061

Main Chapter: BIOS Settings

4.2 Main

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ │Set the Date. Use Tab to │ │ Board Information │switch between Data elements. │ │ Board CB1061 │ │ │ Revision 2 │ │ │ Bios Version 0.32 │ │ │ │ │ │ Processor Information │ │ │ Name Haswell │ │ │ Brand String Intel(R) Core(TM) i5-467 │ │ │ Frequency 3100MHz │ │ │ Processor ID 306c3 │ │ │ Stepping C0 │ │ │ Number of Processors 4Core(s) / 4Thread(s) │────────────────────────────────│ │ Microcode Revision 17 │→←: Select Screen │ │ GT Info GT2 (700 MHz) │↑↓: Select Item │ │ │Enter: Select │ │ IGFX VBIOS Version 2179 │+/-: Change Opt. │ │ Memory RC Version 1.6.2.1 │F1: General Help │ │ Total Memory 16384 MB (DDR3) │F2: Previous Values │ │ Memory Frequency 1600 Mhz │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ System Date [Thu 07/08/2014] │ESC: Exit │ │ System Time [00:47:04] │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Board

Options: none

 Revision

Options: none

 Bios Version

Options: none

 Processor Information

Options: none

 Name

Options: none

 Brand String

Options: none

 Frequency

Options: none

 Processor ID

Options: none

 Stepping

Options: none

 Number of Processors

Options: none

 Microcode Revision

Options: none

Beckhoff New Automation Technology CB1061 page 53

Chapter: BIOS Settings Main  GT Info

Options: none

 IGFX VBIOS Version

Options: none

 Memory RC Version

Options: none

 Total Memory

Options: none

 Memory Frequency

Options: none

 System Date

Options: The system date can be adjusted here.

 System Time

Options: The system time can be adjusted here.

page 54 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings

4.3 Advanced

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Power-Supply Type [ATX] │Select the Type of the Power │ │ SoftOff on Overheat [Disabled] │Supply: AT/ATX │ │► PCI Subsystem Settings │ │ │► ACPI Settings │ │ │► Trusted Computing │ │ │► CPU Configuration │ │ │► SATA Configuration │ │ │► AMT Configuration │ │ │► Power Controller Options │ │ │► USB Configuration │ │ │► Super IO Configuration │ │ │► H/W Monitor │ │ │► Serial Port Console Redirection │────────────────────────────────│ │► Network Stack │→←: Select Screen │ │ │↑↓: Select Item │ │► Intel(R) Ethernet Connection I218-LM - 88:88:88:88:87:88 │Enter: Select │ │► Intel(R) I210 Gigabit Network Connection - 00:01:05:14:... │+/-: Change Opt. │ │► Driver Health │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Power-Supply Type

Options: ATX / AT

 SoftOff on Overheat

Options: Disabled / Enabled

 PCI Subsystem Settings

Sub menu: see "PCI Subsystem Settings" (page 57)

 ACPI Settings

Sub menu: see "ACPI Settings" (page 59)

 Trusted Computing

Sub menu: see "Trusted Computing" (page 60)

 CPU Configuration

Sub menu: see "CPU Configuration" (page 61)

 SATA Configuration

Sub menu: see "SATA Configuration" (page 64)

 AMT Configuration

Sub menu: see "AMT Configuration" (page 67)

 Power Controller Options

Sub menu: see "Power Controller Options" (page 69)

 USB Configuration

Sub menu: see "USB Configuration" (page 71)

 Super IO Configuration

Sub menu: see "Super IO Configuration" (page 72)

Beckhoff New Automation Technology CB1061 page 55

Chapter: BIOS Settings Advanced  H/W Monitor

Sub menu: see "H/W Monitor" (page 74)

 Serial Port Console Redirection

Sub menu: see "Serial Port Console Redirection" (page 76)

 Network Stack

Sub menu: see "Network Stack" (page 79)

 Intel(R) Ethernet Connection I218

Sub menu: see "Intel(R) Ethernet Connection I218-LM" (page 80)

 Driver Health

Sub menu: see "Driver Health" (page 84)

page 56 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings

4.3.1 PCI Subsystem Settings

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PCI Bus Driver Version V 2.05.02 │Value to be programmed into │ │ │PCI Latency Timer Register. │ │ │ │ │ │ │ │ │ │ │ PCI Common Settings │ │ │ PCI Latency Timer [32 PCI Bus Clocks] │ │ │ │ │ │► PCI Express Settings │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 PCI Latency Timer

Options: 32, 64,...224, 248 PCI Bus Clocks

 PCI Express Settings

Sub menu: see "PCI Express Settings" (page 58)

Beckhoff New Automation Technology CB1061 page 57

Chapter: BIOS Settings Advanced

4.3.1.1 PCI Express Settings

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PCI Express Device Register Settings │Enables or Disables PCI │ │ Relaxed Ordering [Disabled] │Express Device Relaxed │ │ Extended Tag [Disabled] │Ordering │ │ No Snoop [Enabled] │ │ │ Maximum Payload [Auto] │ │ │ Maximum Read Request [Auto] │ │ │ │ │ │ PCI Express Link Register Settings │ │ │ ASPM Support [Disabled] │ │ │ WARNING: Enabling ASPM may cause some │ │ │ PCI-E devices to fail │ │ │ Extended Synch [Disabled] │ │ │ │────────────────────────────────│ │ Link Training Retry [5] │→←: Select Screen │ │ Link Training Timeout (uS) 100 │↑↓: Select Item │ │ Unpopulated Links [Disabled] │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Relaxed Ordering

Options: Enabled / Disabled

 Extended Tag

Options: Enabled / Disabled

 No Snoop

Options: Enabled / Disabled

 Maximum Payload

Options: Auto / 128 Bytes / 256 Bytes / 512 Bytes / 1024 Bytes / 2048 Bytes / 4096 Bytes

 Maximum Read Request

Options: Auto / 128 Bytes / 256 Bytes / 512 Bytes / 1024 Bytes / 2048 Bytes / 4096 Bytes

 ASPM Support

Options: Disabled / Auto / Force L0s

 Extended Synch

Options: Enabled / Disabled

 Link Training Retry

Options: Disabled / 2 / 3 / 5

 Link Training Timeout (uS)

Options: 10...1000

 Unpopulated Links

Options: Keep Link ON / Disable Link

page 58 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings

4.3.2 ACPI Settings

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ ACPI Settings │Enables or Disables BIOS ACPI │ │ │Auto Configuration. │ │ Enable ACPI Auto Configuration [Disabled] │ │ │ │ │ │ Enable Hibernation [Enabled] │ │ │ ACPI Sleep State [S1 only(CPU Stop C1...] │ │ │ Lock Legacy Resources [Disabled] │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Enable ACPI Auto Configuration

Options: Enabled / Disabled

 Enable Hibernation

Options: Enabled / Disabled

 ACPI Sleep State

Options: Suspend Disabled / S1 (CPU Stop Clock)

 Lock Legacy Resources

Options: Enabled / Disabled

Beckhoff New Automation Technology CB1061 page 59

Chapter: BIOS Settings Advanced

4.3.3 Trusted Computing

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Configuration │Enables or Disables BIOS │ │ Security Device Support [Disabled] │support for security device. │ │ │O.S. will not show Security │ │ Current Status Information │Device. TCG EFI protocol and │ │ NO Security Device Found │INT1A interface will not be │ │ │available. │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Security Device Support

Options: Enabled / Disabled

page 60 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings

4.3.4 CPU Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ CPU Configuration ▲│Enabled for Windows XP and │ │ █│Linux (OS opimized for │ │ Intel(R) Core(TM) i3-4100E CPU @ 2.40GHz █│Hyper-Threading Technology) │ │ CPU Signature 306c3 █│and Disabled for other OS (OS │ │ Processor Family 6 █│not optimized for │ │ Microcode Patch 16 █│Hyper-Threading Technology). │ │ FSB Speed 100 MHz █│When Disabled only one thread │ │ Max CPU Speed 2400 MHz █│per enabled core is enabled. │ │ Min CPU Speed 800 MHz █│ │ │ CPU Speed 2400 MHz █│ │ │ Processor Cores 4 █│ │ │ Intel HT Technology Not Supported █│ │ │ Intel VT-x Technology Supported █│ │ │ Intel SMX Technology Not Supported █│ │ │ 64-bit Supported █│ │ │ EIST Technology Supported █│────────────────────────────────│ │ CPU C3 State Supported █│→←: Select Screen │ │ CPU C6 State Supported █│↑↓: Select Item │ │ CPU C7 State Supported █│Enter: Select │ │ ░│+/-: Change Opt. │ │ L1 Data Cache 32 kB x 2 ░│F1: General Help │ │ L1 Code Cache 32 kB x 2 ░│F2: Previous Values │ │ L2 Cache 256 kB x 2 ░│F3: Optimized Defaults │ │ L3 Cache 3072 kB ░│F4: Save & Exit │ │ ░│ESC: Exit │ │ ░│ │ │ ░│ │ │ ▼│ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 CPU Signature

Options: none

 Processor Family

Options: none

 Microcode Patch

Options: none

 FSB Speed

Options: none

 Max CPU Speed

Options: none

 Min CPU Speed

Options: none

 CPU Speed

Options: none

 Processor Cores

Options: none

 Intel HT Technology

Options: none

 Intel VT-x Technology

Options: none

 Intel SMX Technology

Options: none

Beckhoff New Automation Technology CB1061 page 61

Chapter: BIOS Settings Advanced  64-bit

Options: none

 EIST Technology

Options: none

 CPU C3 state

Options: none

 CPU C6 state

Options: none

 CPU C7 state

Options: none

 L1 Data Cache

Options: none

 L1 Code Cache

Options: none

 L2 Cache

Options: none

 L3 Cache

Options: none

 Hyper-threading

Options: Enabled / Disabled

 Active Processor Cores

Options: All

 Overclocking lock

Options: Disabled / Enabled

 Limit CPUID Maximum

Options: Enabled / Disabled

 Execute Disable Bit

Options: Enabled / Disabled

 Intel Virtualization Technology

Options: Enabled / Disabled

 Hardware Prefetcher

Options: Disabled / Enabled

 Adjacent Cache Line Prefetch

Options: Disabled / Enabled

 EIST

Options: Disabled / Enabled

 Turbo Mode

Options: Enabled / Disabled

 Package power limit lock

Options: Disabled / Enabled

page 62 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings  CPU Power Limit1

Options: 0..255

 CPU Power Limit1 Time

Options: 0..255

 CPU Power Limit 2

Options: 0..255

 Platform power limit lock

Options: Disabled / Enabled

 CPU Power Limit3

Options: 0..255

 CPU Power Limit3 Time

Options: 0..255

 CPU Power Limit3 Duty Cycle

Options: 0..100

 DDR Power Limit1

Options: 0..255

 DDR Power Limit1 Time

Options: 0..255

 DDR Power Limit2

Options: 0..255

 1-Core Ratio Limit

Options: 0..255

 2-Core Ratio Limit

Options: 0..255

 TCC Activation Offset

Options: 0...15

 ACPI T State

Options: Disabled / Enabled

 CPU DTS

Options: Disabled / Enabled

Beckhoff New Automation Technology CB1061 page 63

Chapter: BIOS Settings Advanced

4.3.5 SATA Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ SATA Controller(s) [Enabled] ▲│Enable or disable SATA Device. │ │ SATA Mode Selection [RAID] █│ │ │ SATA Test Mode [Disabled] █│ │ │ SATA Controller Speed [Default] █│ │ │► Software Feature Mask Configuration █│ │ │ Alternate ID [Disabled] █│ │ │ █│ │ │ Serial ATA Port 0 Empty █│ │ │ Software Preserve Unknown █│ │ │ Port 0 [Enabled] █│ │ │ Hot Plug [Disabled] █│ │ │ External SATA [Disabled] █│ │ │ SATA Device Type [Hard Disk Drive] █│────────────────────────────────│ │ Spin Up Device [Disabled] ░│→←: Select Screen │ │ Serial ATA Port 1 Empty ░│↑↓: Select Item n │ │ Software Preserve Unknown ░│Enter: Select │ │ Port 1 [Inabled] ░│+/-: Change Opt. │ │ Hot Plug [Disabled] ░│F1: General Help │ │ External SATA [Disabled] ░│F2: Previous Values │ │ SATA Device Type [Hard Disk Drive] ░│F3: Optimized Defaults │ │ Spin Up Device [Disabled] ░│F4: Save & Exit │ │ Serial ATA Port 2 Empty ░│ESC: Exit │ │ Software Preserve Unknown ░│ │ │ Port 2 [Enabled] ░│ │ │ Hot Plug [Disabled] ░│ │ │ External SATA [Disabled] ░│ │ │ SATA Device Type [Hard Disk Drive] ▼│ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 SATA Controller(s)

Options: Enabled / Disabled

 SATA Mode Selection

Options: IDE / AHCI / RAID

 SATA Test Mode

Options: Enabled / Disabled

 SATA Controller Speed

Options: Default / Gen1 / Gen2 / Gen3

 Software Feature Mask Configuration

Sub menu: see "Software Feature Mask Configuration" (page 66)

 Alternate ID

Options: Enabled / Disabled

 Serial ATA Port X

Options: none

 Software Preserve

Options: none

 Port X

Options: Enabled / Disabled

 Hot Plug

Options: Enabled / Disabled

 External SATA

Options: Enabled / Disabled

page 64 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings  SATA Device Type

Options: Hard Disk Drive / Solid State Drive

 Spin Up Device

Options: Enabled / Disabled

Beckhoff New Automation Technology CB1061 page 65

Chapter: BIOS Settings Advanced

4.3.5.1 Software Feature Mask Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ RAID0 [Enabled] │Enable or disable RAID0 │ │ RAID1 [Enabled] │feature. │ │ RAID10 [Enabled] │ │ │ RAID5 [Enabled] │ │ │ Intel Rapid Recovery Technology [Enabled] │ │ │ OROM UI and BANNER [Enabled] │ │ │ HDD Unlock [Enabled] │ │ │ LED Locate [Enabled] │ │ │ IRRT Only on eSATA [Enabled] │ │ │ Smart Response Technology [Enabled] │ │ │ OROM UI Delay [2 Seconds] │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 RAID0

Options: Enabled / Disabled

 RAID1

Options: Enabled / Disabled

 RAID10

Options: Enabled / Disabled

 RAID5

Options: Enabled / Disabled

 Intel Rapid Recovery Technology

Options: Enabled / Disabled

 OROM UI and BANNER

Options: Enabled / Disabled

 HDD Unlock

Options: Enabled / Disabled

 LED Locate

Options: Enabled / Disabled

 IRRT Only on eSATA

Options: Enabled / Disabled

 Smart Response Technology

Options: Enabled / Disabled

 OROM UI Delay

Options: 2 / 4 / 6 / 8 Seconds

page 66 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings

4.3.6 AMT Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Intel AMT [Disabled] │Enable/Disabled Intel (R) │ │ BIOS Hotkey Pressed [Disabled] │Active Management Technology │ │ MEBx Selection Screen [Disabled] │BIOS Extension. │ │ Hide Un-Configure ME Confirmation [Disabled] │Note : iAMT H/W is always │ │ MEBx Debug Message Output [Disabled] │enabled. │ │ Un-Configure ME [Disabled] │This option just controls the │ │ Amt Wait Timer 0 │BIOS extension execution. │ │ Disable ME [Disabled] │If enabled, this requires │ │ ASF [Enabled] │additional firmware in the SPI │ │ Activate Remote Assistance Process [Disabled] │device │ │ USB Configure [Enabled] │ │ │ PET Progress [Enabled] │ │ │ AMT CIRA Timeout 0 │────────────────────────────────│ │ Watchdog [Disabled] │→←: Select Screen │ │ OS Timer 0 │↑↓: Select Item │ │ BIOS Timer 0 │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Intel AMT

Options: Disabled / Enabled

 BIOS Hotkey Pressed

Options: Disabled / Enabled

 MEBx Selection Screen

Options: Disabled / Enabled

 Hide Un-Configure ME Configuration

Options: Disabled / Enabled

 MEBx Debug Message Output

Options: Disabled / Enabled

 Un-Configure ME

Options: Disabled / Enabled

 Amt Wait Timer

Options: none

 Disable ME

Options: Disabled / Enabled

 ASF

Options: Disabled / Enabled

 Activate Remote Assistance Process

Options: Disabled / Enabled

 USB Configure

Options: Disabled / Enabled

 PET Progress

Options: Disabled / Enabled

Beckhoff New Automation Technology CB1061 page 67

Chapter: BIOS Settings Advanced  AMT CIRA Timeout

Options: none

 Watchdog

Options: Disabled / Enabled

 OS Timer

Options: none

 BIOS Timer

Options: none

page 68 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings

4.3.7 Power Controller Options

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Bootloader Version 1.00-23 │Select Power line for external │ │ Firmware Version 1.00-43 │USB devices, if powered-down │ │ Mainboard Serial No 11473413400016 │ │ │ Mainboard Prod. Date (Week.Year) 4.14 │ │ │ Mainboard BootCount 254 │ │ │ Mainboard Operation Time 45555min (759h) │ │ │ Voltage (Min/Max) 4.30V / 4.70V │ │ │ Temperature (Min/Max) 26'C /33'C │ │ │ │ │ │ ext. USB-Port Voltage [Off in S3-5] │ │ │ int. USB-Port Voltage [Off in S3-5] │ │ │ │ │ │ WatchDogTimer Mode [Normal Mode] │────────────────────────────────│ │ WDT OSBoot Timeout [Disabled] │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Bootloader Version

Options: none

 Firmware Version

Options: none

 Mainboard Serial No

Options: none

 Mainboard Prod. Date (Week.Year)

Options: none

 Boot Count

Options: none

 Minute Meter

Options: none

 Voltage (Min/Max)

Options: none

 Temperature (Min/Max)

Options: none

 ext. USB-Port Voltage

Options: Off in S3-5 / by SVCC

 int. USB-Port Voltage

Options: Off in S3-5 / by SVCC

 WatchDogTimer Mode

Options: Normal Mode / Compatibility Mode

Beckhoff New Automation Technology CB1061 page 69

Chapter: BIOS Settings Advanced  WDT OSBoot Timeout

Options: Disabled / 45 Seconds ... 255 Seconds

page 70 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings

4.3.8 USB Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ USB Configuration │Enables Legacy USB support. │ │ │AUTO option disables legacy │ │ USB Module Version 8.10.27 │support if no USB devices are │ │ │connected. DISABLE option will │ │ USB Devices: │keep USB devices available │ │ 1 Keyboard, 2 Hubs │only for EFI applications. │ │ │ │ │ Legacy USB Support [Auto] │ │ │ USB3.0 Support [Enabled] │ │ │ XHCI Hand-off [Enabled] │ │ │ EHCI Hand-off [Disabled] │ │ │ │ │ │ USB hardware delays and time-outs: │────────────────────────────────│ │ USB transfer time-out [5 sec] │→←: Select Screen │ │ Device reset time-out [10 sec] │↑↓: Select Item │ │ Device power-up delay [Manual] │Enter: Select │ │ Device power-up delay in seconds 5 │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 USB Module Version

Options: none

 USB Devices

Options: none

 Legacy USB Support

Options: Enabled / Disabled / Auto

 USB3.0 Support

Options: Enabled / Disabled

 XHCI Hand-off

Options: Enabled / Disabled

 EHCI Hand-off

Options: Enabled / Disabled

 USB transfer time-out

Options: 5 sec / 10 sec / 20 sec

 Device reset time-out

Options: 10 sec / 20 sec / 30 sec / 40 sec

 Device power-up delay

Options: Auto / Manual

 Device power-up delay in seconds

Options: 1..40

Beckhoff New Automation Technology CB1061 page 71

Chapter: BIOS Settings Advanced

4.3.9 Super IO Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Super IO Configuration │Set Parameters of Serial Port │ │ │0 (COMA) │ │ Super IO Chip SMSC SCH3114 │ │ │► Serial Port 0 Configuration │ │ │► Serial Port 1 Configuration │ │ │► Serial Port 2 Configuration │ │ │► Serial Port 3 Configuration │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Super IO Chip

Options: none

 Serial Port X Configuration

Sub menu: see "Serial Port Configuration" (page 73)

page 72 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings

4.3.9.1 Serial Port Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Serial Port 0 Configuration │Enable or Disable Serial Port │ │ │(COM) │ │ Serial Port [Enabled] │ │ │ Device Settings IO=3F8h; IRQ=4; │ │ │ │ │ │ Change Settings [Auto] │ │ │ Device Mode [Normal] │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Serial Port

Options: Enabled / Disabled

 Device Settings

Options: none

 Change Settings

Options: Auto / IO=3F8h; IRQ=4 / IO=3F8h; IRQ=3, ...12 / IO=2F8h; IRQ=3, ...12 / IO=3E8h;

IRQ=3, ...12 / IO=2E8h; IRQ=3, ...12

 Device Mode

Options: Normal / High Speed

Beckhoff New Automation Technology CB1061 page 73

Chapter: BIOS Settings Advanced

4.3.10 H/W Monitor

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ H/W Monitor │ │ │ │ │ │ CPU Temperature : +67'C │ │ │ Board Temperature : +32'C │ │ │ Memory Temperature : +28'C │ │ │ SYS FAN Speed : N/A │ │ │ CPU FAN Speed : 2333 RPM │ │ │ AUX FAN Speed : N/A │ │ │ +1.05V : +1.02 V │ │ │ VccCore : +1.74 V │ │ │ +3.3V : +3.22 V │ │ │ Vcc : +4.97 V │ │ │ +12V : +12.17 V │────────────────────────────────│ │ VTR : +3.40 V │→←: Select Screen │ │ Vbat : +0.5 V │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 CPU Temperature

Options: none

 Board Temperature

Options: none

 Memory Temperature

Options: none

 SYS FAN Speed

Options: none

 CPU FAN Speed

Options: none

 AUX FAN Speed

Options: none

 +1.05V

Options: none

 VccCore

Options: none

 +3.3V

Options: none

 Vcc

Options: none

 +12V

Options: none

page 74 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings  VTR

Options: none

 Vbat

Options: none

Beckhoff New Automation Technology CB1061 page 75

Chapter: BIOS Settings Advanced

4.3.11 Serial Port Console Redirection

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ │Console Redirection Enable or │ │ COM0 │Disable. │ │ Console Redirection [Disabled] │ │ │► Console Redirection Settings │ │ │ │ │ │ COM1 │ │ │ Console Redirection [Disabled] │ │ │► Console Redirection Settings │ │ │ │ │ │ COM2 │ │ │ Console Redirection [Disabled] │ │ │► Console Redirection Settings │ │ │ │────────────────────────────────│ │ COM3 │→←: Select Screen │ │ Console Redirection [Disabled] │↑↓: Select Item │ │► Console Redirection Settings │Enter: Select │ │ │+/-: Change Opt. │ │ COM4(Pci Bus0,Dev0,Func0) (Disabled) │F1: General Help │ │ Console Redirection Port Is Disabled │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Console Redirection

Options: Enabled / Disabled

 Console Redirection Settings

Sub menu: see "Console Redirection Settings" (page 77)

page 76 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings

4.3.11.1 Console Redirection Settings

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ COM0 │Emulation: ANSI: Extended │ │ Console Redirection Settings │ASCII char set. VT100: ASCII │ │ │char set. VT100+: Extends │ │ Terminal Type [VT-UTF8] │VT100 to support color, │ │ Bits per second [115200] │function keys, etc. VT-UTF8: │ │ Data Bits [8] │Uses UTF8 encoding to map │ │ Parity [None] │Unicode chars onto 1 or more │ │ Stop Bits [1] │bytes. │ │ Flow Control [None] │ │ │ VT-UTF8 Combo Key Support [Enabled] │ │ │ Recorder Mode [Disabled] │ │ │ Resolution 100x31 [Enabled] │ │ │ Legacy OS Redirection Resolution [80x24] │────────────────────────────────│ │ Putty KeyPad [VT100] │→←: Select Screen │ │ Redirection After BIOS POST [Always Enable] │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Terminal Type

Options: VT100 / VT100+ / VT-UTF8 / ANSI

 Bits per second

Options: 9600 / 19200 / 38400 / 57600 / 115200

 Data Bits

Options: 7 / 8

 Parity

Options: None / Even / Odd / Mark / Space

 Stop Bits

Options: 1 / 2

 Flow Control

Options: None / Hardware RTS/CTS

 VT-UTF8 Combo Key Support

Options: Disabled / Enabled

 Recorder Mode

Options: Disabled / Enabled

 Resolution 100x31

Options: Disabled / Enabled

 Legacy OS Redirection Resolution

Options: 80x24 / 80x25

 Putty KeyPad

Options: VT100 / LINUX / XTERMR6 / SCO / ESCN / VT400

Beckhoff New Automation Technology CB1061 page 77

Chapter: BIOS Settings Advanced  Redirection After BIOS POST

Options: Always Enable / BootLoader

page 78 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings

4.3.12 Network Stack

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Network stack [Enabled] │Enable/Disable UEFI network │ │ IPv4 PXE Support [Enabled] │stack │ │ IPv6 PXE Support [Enabled] │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Network stack

Options: Disabled / Enabled

 IPv4 PXE Support

Options: Disabled / Enabled

 IPv6 PXE Support

Options: Disabled / Enabled

Beckhoff New Automation Technology CB1061 page 79

Chapter: BIOS Settings Advanced

4.3.13 Intel(R) Ethernet Connection I218-LM

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PORT CONFIGURATION MENU │Configure Boot Protocol, Wake │ │► NIC Configuration │on LAN, Link Speed, and VLAn │ │ │ │ │ Blink LEDs 0 │ │ │ │ │ │ PORT CONFIGURATION INFORMATION │ │ │ UEFI Driver: Intel(R) PRO/1000 5.7.06 │ │ │ Adapter PBA: FFFFFF-0FF │ │ │ Chip Type Intel PCH LPT │ │ │ PCI Device ID 153A │ │ │ Bus:Device:Function 00:19:00 │ │ │ Link Status [Disconnected] │ │ │ MAC Address 88:88:88:88:87:88 │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 NIC Configuration

Sub menu: see "NIC Configuration" (page 81)

 Blink LEDs

Options: none

 UEFI Driver:

Options: none

 Adapter PBA:

Options: none

 Chip Type

Options: none

 PCI Device ID

Options: none

 PCI Bus:Device:Function

Options: none

 Link Status

Options: none

 Factory MAC Adress

Options: none

page 80 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings

4.3.13.1 NIC Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Link Speed [Auto Neg] │Specifies the port speed used │ │ Wake On LAN [Enabled] │for the selected boot protocol. │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Link Speed

Options: Auto Negotiated / 10Mbps Half / 10Mbps full / 100Mbps Half / 100Mbps Full

 Wake On LAN

Options: Enabled / Disabled

Beckhoff New Automation Technology CB1061 page 81

Chapter: BIOS Settings Advanced

4.3.14 Intel(R) I210 Gigabit Network Connection

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PORT CONFIGURATION MENU │Configure Boot Protocol, Wake │ │► NIC Configuration │on LAN, Link Speed, and VLAn │ │ │ │ │ Blink LEDs 0 │ │ │ │ │ │ PORT CONFIGURATION INFORMATION │ │ │ UEFI Driver: Intel(R) PRO/1000 5.7.06 │ │ │ Adapter PBA: FFFFFF-0FF │ │ │ Chip Type Intel i210 │ │ │ PCI Device ID 153A │ │ │ Bus:Device:Function 00:19:00 │ │ │ Link Status [Disconnected] │ │ │ MAC Address 88:88:88:88:87:88 │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 NIC Configuration

Sub menu: see "NIC Configuration" (page 81)

 Blink LEDs

Options: none

 UEFI Driver:

Options: none

 Adapter PBA:

Options: none

 Chip Type

Options: none

 PCI Device ID

Options: none

 PCI Bus:Device:Function

Options: none

 Link Status

Options: none

 Factory MAC Adress

Options: none

page 82 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings

4.3.14.1 NIC Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Link Speed [Auto Neg] │Specifies the port speed used │ │ Wake On LAN [Enabled] │for the selected boot protocol. │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Link Speed

Options: Auto Negotiated / 10Mbps Half / 10Mbps full / 100Mbps Half / 100Mbps Full

 Wake On LAN

Options: Enabled / Disabled

Beckhoff New Automation Technology CB1061 page 83

Chapter: BIOS Settings Advanced

4.3.15 Driver Health

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │► Intel(R) PRO/1000 5.7.06 PCI-E Healthy │Provides Health Status for the │ │ │Drivers/Controllers │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Intel(R) PRO/1000 5.7.06 PCI-E

Sub menu: see "Intel(R) Pro/1000 5.7.06 PCI-E" (page 85)

page 84 Beckhoff New Automation Technology CB1061

Advanced Chapter: BIOS Settings

4.3.15.1 Intel(R) Pro/1000 5.7.06 PCI-E

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Controller d2a62b98 Child 0 Healthy │Provides Health Status for the │ │ │Drivers/Controllers │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Controller x Child n

Options: none

Beckhoff New Automation Technology CB1061 page 85

Chapter: BIOS Settings Chipset

4.4 Chipset

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │► PCH-IO Configuration │PCH Parameters │ │► System Agent (SA) Configuration │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 PCH-IO Configuration

Sub menu: see "PCH-IO Configuration" (page 87)

 System Agent (SA) Configuration

Sub menu: see "System Agent (SA) Configuration" (page 94)

page 86 Beckhoff New Automation Technology CB1061

Chipset Chapter: BIOS Settings

4.4.1 PCH-IO Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Intel PCH RC Version 1.6.2.0 │PCI Express Configuration │ │ Intel PCH SKU Name Q87 │settings │ │ Intel PCH Rev ID 04/C1 │ │ │ │ │ │► PCI Express Configuration │ │ │► USB Configuration │ │ │► PCH Azalia Configuration │ │ │ │ │ │ PCH LAN Controller [Enabled] │ │ │ Wake on LAN [Disabled] │ │ │ SLP_LAN# Low on DC Power [Enabled] │ │ │ Second LAN Controller [Enabled] │────────────────────────────────│ │ CLKRUN# Logic [Disabled] │→←: Select Screen │ │ SB CRID [Disabled] │↑↓: Select Item │ │ SLP_S4 Assertion Width [Disabled] │Enter: Select │ │ Restore AC Power Loss [Power On] │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Intel PCH RC Version

Options: none

 Intel PCH SKU Name

Options: none

 Intel PCH Rev ID

Options: none

 PCI Express Configuration

Sub menu: see "PCI Express Configuration" (page 89)

 USB Configuration

Sub menu: see "USB Configuration" (page 92)

 PCH Azalia Configuration

Sub menu: see "PCH Azalia Configuration" (page 93)

 PCH LAN Controller

Options: Disabled / Enabled

 Wake on LAN

Options: Disabled / Enabled

 SLP_LAN# Low on DC Power

Options: Disabled / Enabled

 Second LAN Controller

Options: Disabled / Enabled

 CLKRUN# Logic

Options: Disabled

Beckhoff New Automation Technology CB1061 page 87

Chapter: BIOS Settings Chipset  SB CRID

Options: Disabled / Enabled

 SLP_S4 Assertion Width

Options: Disabled / 1-2 Seconds / 2-3 Seconds / 3-4 Seconds / 4-5 Seconds

 Restore AC Power Loss

Options: Power Off / Power On / Last State

page 88 Beckhoff New Automation Technology CB1061

Chipset Chapter: BIOS Settings

4.4.1.1 PCI Express Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PCI Express Configuration │Enable or disable PCI Express │ │ │Clock Gating for each root │ │ PCI Express Clock Gating [Enabled] │port. │ │ DMI Link ASPM Control [Enabled] │ │ │ DMI Link Extended Synch Control [Disabled] │ │ │ PCIe-USB Glitch W/A [Disabled] │ │ │ Subtractive Decode [Disabled] │ │ │ │ │ │ PCI Express Root Port 1 │ │ │ PCIE Port 2 is assigned to PCIe to PCI Bridge │ │ │ PCIE Port 3 is assigned to LAN │ │ │ PCIE Port 4 is assigned to LAN2 │ │ │► PCI Express Root Port 5 │────────────────────────────────│ │► PCI Express Root Port 6 │→←: Select Screen │ │► PCI Express Root Port 7 │↑↓: Select Item │ │► PCI Express Root Port 8 │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 PCI Express Clock Gating

Options: Disabled / Enabled

 DMI Link ASPM Control

Options: Disabled / Enabled

 DMI Link Extended Synch Control

Options: Disabled / Enabled

 PCIe-USB Glitch W/A

Options: Disabled / Enabled

 Subtractive Decode

Options: Disabled

 PCI Express Root Port X

Sub menu: see "PCI Express Root Port" (page 90)

Beckhoff New Automation Technology CB1061 page 89

Chapter: BIOS Settings Chipset

4.4.1.1.1 PCI Express Root Port

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PCI Express Root Port 2 [Enabled] ▲│Control the PCI Express Root │ │ ASPM Support [Auto] █│Port. │ │ L1 Substates [L1.1 & L1.2] █│ │ │ URR [Disabled] █│ │ │ FER [Disabled] █│ │ │ NFER [Disabled] █│ │ │ CER [Disabled] █│ │ │ CTO [Disabled] █│ │ │ SEFE [Disabled] █│ │ │ SENFE [Disabled] █│ │ │ SECE [Disabled] █│ │ │ PME SCI [Enabled] █│ │ │ Hot Plug [Disabled] █│────────────────────────────────│ │ PCIe Speed [Auto] █│→←: Select Screen │ │ Detect Non-Compliance Device [Disabled] █│↑↓: Select Item │ │ Extra Bus Reserved 0 █│Enter: Select │ │ Reserved Memory 10 █│+/-: Change Opt. │ │ Prefetchable Memory 10 █│F1: General Help │ │ Reserved I/O 4 █│F2: Previous Values │ │ PCIE LTR [Enabled] █│F3: Optimized Defaults │ │ PCIE LTR Lock [Enabled] █│F4: Save & Exit │ │ Snoop Latency Override [Manual] █│ESC: Exit │ │ Snoop Latency Multiplier [1024 ns] █│ │ │ Snoop Latency Value 60 ░│ │ │ Non Snoop Latency Override [Manual] ░│ │ │ ▼│ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 PCI Express Root Port x

Options: Disabled / Enabled

 ASPM Support

Options: Disabled / L0s / L1 / L0sL1 / Auto

 L1 Substates

Options: Disabled / L1.1 / L1.2 / L1.1 & L1.2

 URR

Options: Disabled / Enabled

 FER

Options: Disabled / Enabled

 NFER

Options: Disabled / Enabled

 CER

Options: Disabled / Enabled

 CTO

Options: Disabled / Enabled

 SEFE

Options: Disabled / Enabled

 SENFE

Options: Disabled / Enabled

 SECE

Options: Disabled / Enabled

page 90 Beckhoff New Automation Technology CB1061

Chipset Chapter: BIOS Settings  PME SCI

Options: Disabled / Enabled

 Hot Plug

Options: Disabled / Enabled

 PCIe Speed

Options: Auto / Gen1 / Gen2

 Detect Non-Compliance Device

Options: Disabled / Enabled

 Extra Bus Reserved

Options: 0...7

 Reserved Memory

Options: 1...20

 Prefetchable Memory

Options: 1...20

 Reserved I/O

Options: 4 / 8 / 12 / 16 / 20

 PCIE LTR

Options: Disabled / Enabled

 PCIE LTR Lock

Options: Disabled / Enabled

 Snoop Latency Override

Options: Disabled / Manual / Auto

 Snoop Latency Multiplier

Options: 1 / 32 / 1024 / 32768 / 1048576 / 33554432 ns

 Snoop Latency Value

Options: none

 Non Snoop Latency Override

Options: Disabled / Manual / Auto

 Non Snoop Latency Multiplier

Options: 1 / 32 / 1024 / 32768 / 1048576 / 33554432 ns

 Non Snoop Latency Value

Options: none

Beckhoff New Automation Technology CB1061 page 91

Chapter: BIOS Settings Chipset

4.4.1.2 USB Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ USB Configuration │Precondition work on USB host │ │ │controller and root ports for │ │ USB Precondition [Disabled] │faster enumeration. │ │ XHCI Mode [Manual] │ │ │ BTCG [Enabled] │ │ │ │ │ │ XHCI Pre-Boot Driver [Enabled] │ │ │ │ │ │ Route USB 2.0 pins to which HC? [Route Per-Pin] │ │ │ USB 2.0 PIN #0 [Route to EHCI] │ │ │ USB 2.0 PIN #1 [Route to EHCI] │ │ │ USB 2.0 PIN #2 [Route to EHCI] │ │ │ USB 2.0 PIN #3 [Route to EHCI] │────────────────────────────────│ │ USB 2.0 PIN #4 [Route to EHCI] │→←: Select Screen │ │ USB 2.0 PIN #5 [Route to EHCI] │↑↓: Select Item │ │ USB 2.0 PIN #6 [Route to EHCI] │Enter: Select │ │ USB 2.0 PIN #7 [Route to EHCI] │+/-: Change Opt. │ │ USB 2.0 PIN #8 [Route to EHCI] │F1: General Help │ │ USB 2.0 PIN #9 [Route to EHCI] │F2: Previous Values │ │ USB 2.0 PIN #10 [Route to EHCI] │F3: Optimized Defaults │ │ USB 2.0 PIN #11 [Route to EHCI] │F4: Save & Exit │ │ USB 2.0 PIN #12 [Route to EHCI] │ESC: Exit │ │ USB 2.0 PIN #13 [Route to EHCI] │ │ │ │ │ │ Enable USB 3.0 pins [Select Per-Pin] │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 USB Precondition

Options: Disabled / Enabled

 XHCI Mode

Options: Smart Auto / Auto / Enabled / Disabled / Manual

 BTCG

Options: Disabled / Enabled

 XHCI Pre-Boot Driver

Options: Disabled / Enabled

 Route USB 2.0 pins to which HC?

Options: Route Per-Pin / Route all Pins to EHCI / Route all Pins to XHCI

 USB 2.0 PIN #X

Options: Route to EHCI / Route to XHCI

 Enable USB 3.0 pins

Options: Select Per-Pin / Disable all Pins / Enable all Pins

 USB 3.0 PIN #X

Options: Disabled / Enabled

 USB Ports Per-Port Disable Control

Options: Disabled / Enabled

 USB Port #X

Options: Disabled / Enabled

 USB3.0 Port #X

Options: Disabled / Enabled

page 92 Beckhoff New Automation Technology CB1061

Chipset Chapter: BIOS Settings

4.4.1.3 PCH Azalia Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PCH Azalia Configuration │Control Detection of the │ │ │Azalia device. │ │ Azalia [Enabled] │Disabled = Azalia will be │ │ Azalia PME [Disabled] │unconditionally disabled │ │ │Enabled = Azalia will be │ │ │unconditionally Enabled │ │ │Auto = Azalia will be enabled │ │ │if present, disabled otherwise. │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Azalia

Options: Disabled / Enabled / Auto

 Azalia PME

Options: Disabled / Enabled

Beckhoff New Automation Technology CB1061 page 93

Chapter: BIOS Settings Chipset

4.4.2 System Agent (SA) Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ System Agent Bridge Name Haswell │Check to enable VT-d function │ │ System Agent RC Version 1.6.2.0 │on MCH. │ │ VT-d Capability Supported │ │ │ │ │ │ VT-d [Enabled] │ │ │ CHAP Device (B0:D7:F0) [Disabled] │ │ │ Thermal Device (B0:D4:F0) [Disabled] │ │ │ CPU SA Audio Device (B0:D3:F0) [Disabled] │ │ │ Enable NB CRID [Disabled] │ │ │ BDAT ACPI Table Support [Disabled] │ │ │ │ │ │► Graphics Configuartion │ │ │► NB PCIe Configuration │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 VT-d

Options: Disabled / Enabled

 CHAP Device (B0:D7:F0)

Options: Disabled / Enabled

 Thermal Device (B0:D4:F0)

Options: Disabled / Enabled

 CPU SA Audio Device (B0:D3:F0)

Options: Disabled / Enabled

 Enable NB CRID

Options: Disabled / Enabled

 BDAT ACPI Table Support

Options: Disabled / Enabled

 Graphics Configuration

Sub menu: see "Graphics Configuration" (page 95)

 NB PCIe Configuration

Sub menu: see "NB PCIe Configuration" (page 98)

page 94 Beckhoff New Automation Technology CB1061

Chipset Chapter: BIOS Settings

4.4.2.1 Graphics Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Graphics Configuration │Graphics turbo IMON current │ │ IGFX VBIOS Version 2189 │values supported (14-31) │ │ IGFX Frequency 800 MHz │ │ │ Graphics Turbo IMON Current 31 │ │ │ │ │ │ Primary Display [Auto] │ │ │ Primary PEG [Auto] │ │ │ Primary PCIE [Auto] │ │ │ Internal Graphics [Auto] │ │ │ Aperture Size [256MB] │ │ │ DVMT Pre-Allocated [64M] │ │ │ DVMT Total Gfx Mem [256M] │ │ │ Gfx Low Power Mode [Disabled] │────────────────────────────────│ │ Panel Power Enable [Disabled] │→←: Select Screen │ │► LCD Control │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 IGFX VBIOS Version

Options: none

 IGFX Frequency

Options: none

 Graphics Turbo IMON Current

Options: 14...31

 Primary Display

Options: Auto / IGFX / PEG / PCI

 Primary PEG

Options: Auto / PEG11 / PEG 12

 Primary PCIE

Options: Auto / PCIE1 / PCIE2 / ... / PCIE7

 Internal Graphics

Options: Auto / Disabled / Enabled

 Aperture Size

Options: 128MB / 256MB / 512MB

 DVMT Pre-Allocated

Options: 32M / 64M ... 480M / 512M / 1024M

 DVMT Total Gfx Mem

Options: 128M / 256M / MAX

 Gfx Low Power Mode

Options: Disabled / Enabled

Beckhoff New Automation Technology CB1061 page 95

Chapter: BIOS Settings Chipset  Panel Power Enable

Options: Disabled / Enabled

 LCD Control

Sub menu: see "LCD Control" (page 97)

page 96 Beckhoff New Automation Technology CB1061

Chipset Chapter: BIOS Settings

4.4.2.1.1 LCD Control

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ LCD Control │Select the Video Device which │ │ │will be activated during POST. │ │ Primary IGFX Boot Display [CRT] │This has no effect if external │ │ Secondary IGFX Boot Display [Disabled] │graphics present. │ │ SDVO-LFP Panel Type [VBIOS Default] │Secondary boot display │ │ BIA [Auto] │selection will appear based on │ │ Spread Spectrum clock Chip [Off] │your selection. │ │ ALS Support [Disabled] │VGA modes will be supported │ │ │only on primary display │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Primary IGFX Boot Display

Options: VBIOS Default / CRT / EFP / LFP / EFP3 / EFP2 / LFP2

 Secondary IGFX Boot Display

Options: VBIOS Default / CRT / EFP / LFP / EFP3 / EFP2 / LFP2

 SDVO-LFP Panel Type

Options: VBIOS Default / 1024x768 SDVO-LFP / 1280x1024 SDVO-LFP / 1400x1050 SDVO-LFP

/ 1600x1200 SDVO-LFP

 BIA

Options: Auto / Disabled / Level 1..5

 Spread Spectrum Clock Chip

Options: Off / Hardware / Software

 ALS Support

Options: Disabled / Enabled

Beckhoff New Automation Technology CB1061 page 97

Chapter: BIOS Settings Chipset

4.4.2.2 NB PCIe Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ NB PCIe Configuration ▲│Configure PEG0 B0:D1:F0 │ │ PEG0 Not present █│Gen1-Gen3 │ │ PEG0 - Gen X [Auto] █│ │ │ PEG1 Not Present █│ │ │ PEG1 - Gen X [Auto] █│ │ │ PEG2 Not Present █│ │ │ PEG2 - Gen X [Auto] █│ │ │ █│ │ │ Run-time C7 Allowed [Enabled] █│ │ │ Enable PEG [Auto] █│ │ │ Detect Non-Compliance Device [Disabled] █│ │ │ Program PCIe ASPM after OpROM [Disabled] █│ │ │ PEG0 De-emphasis Control [-3.5 dB] █│────────────────────────────────│ │ PEG1 De-emphasis Control [-3.5 dB] █│→←: Select Screen │ │ PEG2 De-emphasis Control [-3.5 dB] █│↑↓: Select Item │ │ PEG0 - ASPM [ASPM L0s] █│Enter: Select │ │ ASPM L0s [Both Root and Endpo...] █│+/-: Change Opt. │ │ PEG1 - ASPM [ASPM L0sL1] ░│F1: General Help │ │ ASPM L0s [Both Root and Endpo...] ░│F2: Previous Values │ │ PEG2 - ASPM [ASPM L0sL1] ░│F3: Optimized Defaults │ │ ASPM L0s [Both Root and Endpo...] ░│F4: Save & Exit │ │ PEG Sampler Calibrate [Disabled] ░│ESC: Exit │ │ Swing Control [Full] ░│ │ │ PEG Gen3 Equalization [Disabled] ░│ │ │ Gen3 Eq Preset Search [Enabled] ░│ │ │ ▼│ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 PEGn - Gen X

Options: Auto / Gen1 / Gen2 / Gen3

 Run-time C7 Allowed

Options: Disabled / Enabled

 Enable PEG

Options: Disabled / Enabled / Auto

 Detect Non-Compliance Device

Options: Disabled / Enabled

 Program PCIe ASPM after OpROM

Options: Enabled / Disabled

 De-emphasis Control

Options: -6 dB / -3.5 dB

 PEGn ASPM

Options: Disabled / Auto / ASPM L0s / ASPM L1 / ASPM L0sL1

 ASPM L0s

Options: Root Port Only / Endpoint Port Only / Both Root and Endpoint Ports

 PEG Sampler Calibrate

Options: Auto / Disabled / Enabled

 Swing Control

Options: Reduced / Half / Full

 Gen3 Equalization

Options: Disabled / Enabled

page 98 Beckhoff New Automation Technology CB1061

Chipset Chapter: BIOS Settings  Gen3 Eq Preset Search

Options: Enabled / Disabled

 Always re-search Gen3 Eq Preset

Options: Enabled / Disabled

 Allow PERST# GPIO Usage

Options: Enabled / Disabled

 Preset Search Dwell Time

Options: 0-65535

 Timing Margin Steps

Options: 1-255

 Timing Start Margin

Options: 4-255

 Voltage Margin Steps

Options: 1-255

 Voltage Start Margin

Options: 4-255

 Favor Timing Margin

Options: Enabled / Disabled

 Error Target

Options: 0-65535

 PEG RxCEM LoopBack Mode

Options: Enabled / Disabled

 PEG Lane number for Test

Options: 0-15

 PCIe Gen3 RxCTLEp Setting

Options: 0...15

Beckhoff New Automation Technology CB1061 page 99

Chapter: BIOS Settings Chipset

4.4.2.2.1 PEG Gen3 Root Port Preset Value for each Lane

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PEG Gen3 Root Port Preset Value for each Lane │Lane 0 Root port preset value │ │ │for Gen3 Equalization. │ │ Gen3 Root Port Preset Lane 0 8 │ │ │ Gen3 Root Port Preset Lane 1 8 │ │ │ Gen3 Root Port Preset Lane 2 8 │ │ │ Gen3 Root Port Preset Lane 3 8 │ │ │ Gen3 Root Port Preset Lane 4 8 │ │ │ Gen3 Root Port Preset Lane 5 8 │ │ │ Gen3 Root Port Preset Lane 6 8 │ │ │ Gen3 Root Port Preset Lane 7 8 │ │ │ Gen3 Root Port Preset Lane 8 8 │ │ │ Gen3 Root Port Preset Lane 9 8 │ │ │ Gen3 Root Port Preset Lane 10 8 │────────────────────────────────│ │ Gen3 Root Port Preset Lane 11 8 │→←: Select Screen │ │ Gen3 Root Port Preset Lane 12 8 │↑↓: Select Item │ │ Gen3 Root Port Preset Lane 13 8 │Enter: Select │ │ Gen3 Root Port Preset Lane 14 8 │+/-: Change Opt. │ │ Gen3 Root Port Preset Lane 15 8 │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Gen3 Root Port Preset Value for each Lane

Options: 1..11

page 100 Beckhoff New Automation Technology CB1061

BECKHOFF CB1061 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual