Bang & Olufsen BeoVision 9 User Manual

Download

Page 1

BeoVision 9

Guide

Page 2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No User-serviceable parts inside.

Refer servicing to qualied service

personnel.

WARNING: To reduce the risk of re or

electric shock, do not expose this

appliance to rain or moisture. Do not expose this equipment to dripping or splashing and ensure that no objects lled with liquids, such as vases, are placed on the equipment. To completely disconnect this equipment from the AC Mains, disconnect the mains plug from

the wall socket. The disconnect device

shall remain readily operable.

Cautions

– Make sure that the product is set up, placed and

connected in accordance with the instructions in this Guide.

– Place your product on a rm and stable surface.

To prevent injury, use Bang & Olufsen approved

stands and wall brackets only! – Do not place any items on top of your product. – Do not subject the product to high humidity, rain

or sources of heat. – The product is developed for indoor use in dry,

domestic environments only. Use within a

temperature range of 50–95°F (10–35°C), and

at an altitude of no more than 5000 ft (1500 m).

– Do not place the T V in direct sunlight, as this

may reduce the sensitivity of the remote control

rece iver.

– Leave enough space around the product for

adequate ventilation.

– Do not connect any of the products in your

system to the mains, until you have connected

all the cables. – Do not attempt to open the product. Leave

such operations to qualied service personnel. – The product can only be switched off completely

by disconnecting it from the wall socket.

The lightning flash with arrowhead symbol within an equilateral triangle, is

intended to alert the user to the

presence of uninsulated “dangerous

voltage” within the product’s

enclosure that may be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servicing)

instructions in the literature

accompanying the product.

Page 3

Dear Customer

Contents

This Guide contains information about the daily use of your

Bang & Olufsen product and about connecting and operating external equipment. We expect your retailer to deliver, install and set up your product.

On the Bang & Olufsen website, www.bang-olufsen.com, you can

nd further information and relevant FAQs about your product.

The needs of the user are considered carefully when designing

and developing Bang & Olufsen products. Therefore, please take the time to tell us about your experience with your product.

To contact us, visit our website on …

www.bang-olufsen.com

or write to: Bang & Olufsen a/s BeoCare Peter Bangs Vej 15 DK–7600 Struer

or fax: Bang & Olufsen BeoCare +45 9785 3911 (fax)

4 Watch television

6 Digital tuner

8 Access to BeoMaster 5

11 BeoLink

21 Advanced use

39 Installation – setup

Technical specications, features and the use

thereof are subject to change without notice.

3510335 0903

Page 4

STOP

PLAY

BACK

Living Room

TV V.MEM RADIO

DTV N.MUSIC N.RADIO

PC DVD CD

TV LIGHT RADIO

DTV DVD CD

V MEM RECORD A MEM

789

456

TEXT

123

LIST EXIT

STOP

How to use your remote control

You can operate your television with

Beo5 or Beo4. The instructions in this Guide are mainly based on Beo5.

Beo5 operation Beo4 operation

Soft button, touch screen to select*

Switch on a source or select a function

Back up through Beo5 displays

Bring up SCENE buttons, such as Zones or Speaker

Press again to return

Bring up digits to select channel or recording

Press again to return

Back up through menus or press once to pause

STOP

playback and twice to stop

Start playback

PL AY

Exit menus completely

BACK

Select colour specic functions*

Press volume wheel next to the colour

Turn to adjust volume

To mute, turn quickly counter-clockwise

Press centre button to accept and store settings

V MEM

The Beo4 display shows you the activated source or function

Switch on the TV*

Switch on a connected video recorder

Select channels and enter information in on-screen menus

0 – 9

Bring up the main menu of the active source

Activate Closed Captioning

TEXT

Search backwards or forwards or move in menus

Accept and store settings and start playback

Step through channels or move in menus

Hold for continuous step

Select colour specic functions

Useful hints

*About buttons

*Coloured buttons

Actual zone

Soft buttons

Step through screen menus

Search backwards or forwards

Recordings

Step through channels or recordings

Hold for continuous step

Standby

Light grey buttons indicate that you have to press a text in the display. Dark grey buttons indicate that you have to press a hard button. Press the wheel next to the colour to activate a coloured button. Indicates the actual zone as it was named during the setup process. Depending on the activated source, different soft buttons appear on the screen. Touch the screen to activate the function.

Adjust volume

To mute, press the middle of the button

Display extra ‘buttons’ on the Beo4

LIST

Press repeatedly to change ‘buttons’

Back up through menus or press once to pause playback and

STOP

twice to stop

Exit menus

EXIT

Standby

*Marked buttons can be recongured during the setup process. See p. 43.

My reconguration:

DTV

NOTE! For general information about

remote control operation, see the Guide enclosed with your remote control.

Page 5

Introduction

TV SETUP

CHANNEL SETUP

PLAY TIMER

OPTIONS

STAND POSITIONS

select

Watch movies and listen to different sources, such as a connected set-top box or a music centre.

Display and menus

Information about the selected source is shown at the top of the screen. On-screen menus allow you to adjust settings.

Menu name

Menu options

Information eld

Navigate in menus

When a menu is on the screen, you can move between menu options, reveal

settings or enter data.

… TV Menu

zone

Select option/ setting

Switch on TV

Enter data Bring up sub-

0–9

Show menu Select TV’s

menu/store

setting

BACK

Select option Exit menus*4

Watch television • Digital tuner • Access to BeoMaster 5 Easy use

Important – for more information: www.bang-olufsen.com

Remote control The instructions in this Guide are mainly based on the Beo5

remote control, but you can also operate the TV with Beo4. On the fold-out page in this Guide, you will nd an overview of the buttons on Beo5 and Beo4. For general information about remote control operation, see the Guide enclosed with your remote control.

*NOTE! Press STOP to back up through

menus.

Page 6

TV CHANNEL LIST

CNN 1

MOVIE NW 2 DISCOVER 3 CWNBC 4 BBCWORLD 5 SUPER CH 6 CRIME TV 7 CINEMA 8 9 10 11 12 13 14 15 16 17 18

more select

Watch television

Choose a TV channel by its number or switch to another channel or source. Adjust the sound volume, change the

sound type or language and turn the TV.

Activate the TV source to use these

functions

Channel name

Channel number

Beo5 operation

Switch on the TV

Select a TV channel

Bring up a channel list

Adjust the volume

Indicates more channels

Useful hints

Automatic Colour

Management

Record here and now on a recorder

While recording on a connected recorder you can also watch another recording, source, or TV channel.

Turn the TV

See second source

Divide the screen to watch two sources at the

same time.

Switch off the TV

Automatic colour calibration may start

automatically.

Automatic Colour Management automatically compensates for colour changes on the screen for every 100 hours of use approximately. Do not switch off the system or disconnect it from the mains during the calibration.

Page 7

Beo4 operation

Press

Select Select

Hold for

channel list

Adjust volume. To mute, turn quickly

counter-clockwise

Record Record

Activate numbers

Select page

0–9

channel

Select channel

Start recording

Stand Turn Turn

Press

Turn TV

Select previous channel

0–9

Bring back the sound by turning the

wheel either way.

STOP STOP

Stop recording

Position

1…9

Select position*

Press

0–9

Select Select

channel

Hold to

activate

Adjust volume

RECORD

Press twice to start Press twice to

LIST

Select STA ND

Select page or channel and

To mute, press in the middle

of the button

STOP

stop

1–9

Turn TV

Select

position*

P-and-P DVD Swap

Press

source

Swap pictures Select

Press

Second source

You can bring up two video sources. With Swap you can make the left

and right pictures switch places. With BACK you leave the function and go to the source on the left. You can also just select the source

*TV positions

you wish to go to. See also p. 46 for information about HDMI sources. Position 1 is the far left position and Position 9 is the far right.

LIST

Select P-AND-P

DVD

Select source

Swap pictures

Press

To use the stand function, you have

NOTE! to calibrate the stand rst, see p. 49. To preset positions for the T V to turn to, see p. 52.

Page 8

Air 11-1 KNTV-HD 3:30 AM, Tue Sep 28

9:00AM-10:00AM Gone with the Wind

Mode: HD Language: Multi

CC: Caption Rating: TV-14

Digital tuner

When you select the built-in ATSC tuner, you can receive digital terrestrial and open cable programmes.

Activate the digital tuner

Channel number

Channel name

Programme name

Time and date

Beo5 operation

Switch on the ATSC tuner

Activate the built-in ATSC tuner.

Bring up the tuner menu

Bring up the menu to make or change settings.

Bring up a channel list

While you watch T V, you can bring up a Channel list or a list of your favourite channels.

Change Closed Captioning

Change Closed Captioning for the current channel.*1

Additional caption options*

Programme mode

Programme duration

Useful hints

Channel Delimiter

Closed Captioning

Audio options

*Korea

Bring up programme information

Bring up information on the programme you are

currently watching.

Bring up a Programme Guide

Programme rating*

Additional audio options

Bring up a Programme Guide with information on the current and next programmes.

Change audio language

Change audio language for the current channel.

Switch off the ATSC tuner

Closed Captioning and programme rating are not available in Korea. Press the yellow button to activate the Channel Delimiter. If Closed Captioning is available, it is indicated in the programme information. If an additional audio option is available, it is indicated which language. ‘Multi’ indicates that more than one language is available.

Page 9

Beo4 operation

DTV

change screen mode

Setup

Press

List

Show channel list

Press

Infor-

mation

Press

Progr.

Guide

Press

Move up/ down

0…9

Bring up

7-day list

Specic programme information

Select channel Select page Accept

Step in pages

Select

programme

DTV

Press Press repeatedly to

Press

Hold to

activate

TEXT

Press

Select page or channel and

Navigate and select programme

Press Press

Press

Programme Guide With a Beo4 remote control you can also bring up a 7-day list and specic programme

information by means of the blue button.

Press

Page 10

Source selection Leave mode Add to playlist Home/Return . Random on/off Show info/Hide info List root Play all/Play group Full Size cover/Track info view Delete Conﬁguration Rename

EXIT

1 2 3 4 5 6 7 8 9 0

Access to BeoMaster 5

If your TV is equipped with the optional BeoMaster, you can bring up BeoMaster sources on the TV screen to get access to N.Music, N.Radio, photos, and web.

Activate the BeoMaster in order to

use these functions

Beo5 operation

Select a BeoMaster source

When you have brought up the source selection

menu, choose from different media sources.

Select function*1

The menu overlay gives you quick access to

selected functions.

Useful hints

Switch off the BeoMaster

*Menu overlay The menu overlay shows the options you have with a selected source.

Page 11

PC LIST

Press

Select source

Beo4 operation

Select PC

Select source

Show menu

overlay

Switch source Switch off TV

Remote control Use your remote control to switch sources on and off, search for

Select function

specic stations or tracks, access additional functions, and adjust volume.

0–9

BACK

Show menu overlay and select function

Switch source

NOTE! For further information about the BeoMaster, refer to the Guide enclosed

with your BeoMaster.

0–9

or or

Switch off TV

EXIT

Page 12

Page 13

Contents – BeoLink

12 BeoLink system

14 Connect and set up an audio system

16 Connect and set up a BeoLink system

17 Your television in a link room

18 Two televisions in the same room

BeoLink

BeoLink system • Connect and set up an audio system • Connect and set up a BeoLink system • Your television in a link room …

Page 14

BeoLink system

If you have a BeoLink system, you can operate all connected sources from both the main room and link rooms.

Activate main or link room sources

Link room

Beo5 operation

TV sound on the audio speakers

Listen to sound from a TV source on your audio system speakers.

Audio sound on the TV speakers

Listen to audio sound on the speakers connected to the TV.

Use a source present in one room

Activate a main or link room source in a link room.

The source type is only present in one room.

Useful hints

Main room source

Options

Link room source

Audio system

Use a link room source

Activate a link room source in a link room. The source type is present in both rooms.

Use a main room source

Main room

Activate a main room source from a link room. The source type is present in both rooms.

Stereo sound in a link room

If stereo sound is selected in the link room, you cannot distribute other main room sources to the link room system.*

To use all functions properly, the products must be set to the correct options. See p. 14. This is the central source from which you can distribute sound and pictures to link room

sources.

This source is placed in the link room and through the source you can receive sound and

pictures from connected main room sources.

Only Bang & Olufsen audio systems with Master Link support integration with the T V.

Page 15

Beo4 operation

… TV

Select audio speaker zone

…

RADIO

Select source

Select audio source Select TV speaker zone

Operate source as usual

LIST TV

LIST

Select video source Select video source

Select audio source

Operate source as usual

Select AV*

RADIO

Select source

Select source Operate source as usual

Link

Press Select source

TV AV

*Sound

Usually sound distributed from a main room video source, such as a settop box, to the link room is transmitted in mono. However, you can

select stereo sound.

Changes in link

room setup

If you move your link room products to other rooms, remember to get your Beo5 remote control recongured by your Bang & Olufsen retailer.

LIST TV

Operate source as usual Operate source

DTV

Select main room source Press Select AV*

Select LINK*

Switch on TV Switch on TV

*NOTE! In order to display AV and LINK on

Select source

LIST

as usual

Select main room source

DTV

Beo4, you must rst add it to the Beo4 list of functions. See the Guide enclosed with your

Beo4.

Page 16

MASTER LINKMASTER LINK

1. Connect the audio system

2. Set option for TV

If your TV has been set up in an audio/ video system, set it to the correct option. Switch the entire system to standby rst and place yourself in front of the TV.

Connect and set up an audio system

To obtain the benets of an integrated audio/video system, connect a

compatible Bang & Olufsen audio system to the TV using a Master Link cable.

Connect the available sockets marked MASTER LINK on the TV and the audio system using a Master Link cable.

Option

and

Hold

Hold Press

and

Press

LIST

pgm

Press

LIST LIST 0 –9

Select OPTION? and

…

Select zone in which T V is placed

Select V.OP T Select

Option

3. Set option for audio system

Set the audio system to the correct option. Switch the entire system to standby rst and place yourself in front of the audio system.

Useful hints

TV and audio speakers

Choice of options

Option

and

Hold

Hold Press

Play a CD on your audio system using speakers connected to the TV, or switch on a TV programme and send the sound to your audio system speakers. If you have a Beo4 remote control, options for the T V can be 1, 2, or 4 in a main room and 5 or 6 in a link room. Options for the audio system can be 0, 1, 2, 5, 6. See also p. 17.

and

Press

LIST

pgm

Press

LIST LIST 0 –9

Select OPTION? and

…

Select zone in which

audio system is placed

Select A.OPT

Select Option

Page 17

Select options

Option 0Option 2

Option 1Option 1

Option 2Option 2

To set the correct options with the Beo5

remote control, you must select the zone in which your product is placed, see p. 14. To set the correct options with the Beo4 remote control, you can get an overview of options

on this page.

Your audio/video system can be placed together in one room, or in two

rooms with the TV in one and the audio system with a set of speakers in

another.

The TV and audio system are set up in one

room with all speakers connected to the T V. Set the TV to Option 2 and the audio system to Option 0.

The TV with or without additional speakers

and an audio system with a connected set of

speakers are set up in one room. Set the TV to Option 1 and the audio system to Option 1.

Options For information about Option 4, 5 and 6, see pp. 17–18.

The audio system is set up in one room and

the TV with or without additional speakers in

another.

Set the TV to Option 2 and the audio system to Option 2.

NOTE! Not all Bang & Olufsen audio systems

support integration with the TV.

Page 18

MASTER LINK

RF Link

Amplifier

LINK TV TV

Make link connections

To distribute video signals to link rooms, it is

necessary to connect an RF Link Amplier to the main room T V and a link room TV.*1

Connect and set up a BeoLink system

Connect and set up a BeoLink system to see pictures and hear sound in link

rooms. You can, for example, connect the living room TV to another video

system or to a set of speakers in another room.

Connect the Master Link cable to the available socket marked MASTER LINK on the

TV.

To distribute video signals to link rooms,

connect an ordinary aerial cable to the socket marked LINK TV on the main connection panel. Then run the aerial cable to the RF Link

Amplier and the Master Link cable to the

link room. Follow the instructions enclosed with the link room equipment.

Switch on the system modulator

If you have an audio setup, such as a BeoLink Active/Passive, and you set up a non-linkable

TV in the same room, you must set the

system modulator to ‘ON’. The factory setting is ‘AUTO’, which must be used if you are using a linkable Bang & Olufsen TV.

Change the link channel

If, e.g., a TV channel in your area is broadcasted on the same channel as the factor y setting for the BeoLink system; channel 66, you must tune the system modulator to an unoccupied channel.*2

Useful hints

*Connected

equipment

*Link channel

If an audio system is already connected to the MASTER LINK socket and you wish to connect more equipment, the Master Link cable must be split in two and joined with the cable from the link room using a special junction box. Contact your Bang & Olufsen retailer for assistance. When you change the link channel in the main room T V, make sure that the link channel in the link room corresponds to it.

Select ‘OPTIONS’ in

‘TV SETUP’ menu

Select ‘OPTIONS’ in

‘TV SETUP’ menu

Select ‘LINK’ in

‘CONNECTIONS‘

Select ‘LINK’ in

‘CONNECTIONS‘

Select

‘MODULATOR’

Select

‘C HA NN EL’

NOTE! Only sources with an analogue signal can be distributed from a main room TV to the link room system.

Reveal ‘ON’ Accept

Find unused

channel

Page 19

Your television in a link room

If you have a BeoLink system, operate all connected systems through the TV in a link room.

Connect link room TV

Follow the procedure described here when you connect your TV for use in a link room.

Set option for a link room TV

For your entire system to function properly, it is essential that the TV in the link room is set to the correct option before you connect it to the system in the main room. Place yourself in front of the link room TV.

1 Connect the link room TV to the mains

sup pl y.

2 Using your remote control, programme

the link room T V to the correct option.

3 Disconnect the link room T V from the

mains.

4 Make the necessary connections. 5 Reconnect the link room TV to the

mains supply.

and

Hold

Hold Press

and

Press

LIST

Press

Select OPTION? and accept

Option

pgm

LIST LIST 6

…

Select zone in which T V is placed

Select V.OP T Select Option

BeoMaster

Timer programming

If your TV is equipped with a BeoMaster, it cannot be set up and used in a link room. Programme a Play Timer on the T V in the main room.

*NOTE!

If you have a Beo4 and you connect

the TV for use in a link room where other link

systems are already connected, such as

speakers, you must set the T V to Option 5

instead.

Page 20

BeoVision 9 Zone ‘A’

Zone ‘B’

Zone ‘A’

BeoVision 9

Zone ‘B’

Set the correct option

If you place your T V in a room where you already have a Bang & Olufsen T V and commands from your remote control can be received by both TVs, you must change the option of the secondary TV to prevent simultaneous activation of both T Vs. Place yourself in front of the secondary T V.

Two televisions in the same room

If you have two TVs in the same room and one remote control for both TVs, it is essential that the TVs are set to the correct options, for them to function properly.

Option

and

Hold

Hold Press

and

Press

LIST

pgm

Press

LIST LIST 4

Select OPTION? and accept

…

Select zone in which T V is

placed*

Select V.OP T Select Option

Beo5 – operate the TVs

Normally you can activate a source simply by pressing the relevant source button, but if you have two T Vs in the same room, you must remember rst to select the zone of the

TV you wish to use, if you have a Beo5.

Useful hints

Select zone in which desired T V is placed

TV…

Select source

LINK on Beo4 In order to display LINK on Beo4, you must rst add it to the Beo4 list of functions. See the

Guide enclosed with your Beo4 for more information.

Page 21

BeoVision 9 Option 4

LIST

LINK

Beo4 – operate TV in option 4

Normally you can activate a source simply by pressing the relevant source button, but if your TV is set to Option 4, you must do the following to activate a source, if you have a

Beo4.

However, if you wish to dedicate a remote

control to your secondary T V, contact your

Bang & Olufsen retailer.

LIST TV

Select LINK

Select source

*NOTE! For information about choice of zone, contact your Bang & Olufsen retailer.

Page 22

Page 23

Contents – Advanced use

22 Surround sound and Home cinema

23 Sound type

24 Wake-up Timer

25 Play Timer

26 Scan in TV channels

27 Edit scanned TV channels

28 Adjust picture and sound settings

29 Activate parental control

30 Apply Closed Captioning

31 Calibrate colour accuracy of the screen

32 Settings for the digital tuner

34 The pincode system

35 Tuner setup

36 Operate other equipment with Beo5 or Beo4

Surround sound and Home cinema • Sound type • Wake-up Timer • Play Timer • Scan in T V channels … Advanced use

Page 24

Surround sound and Home cinema

When you add Bang & Olufsen loudspeakers and a projector, you can turn your

TV into a Home cinema system with surround sound. You can also select a

picture format to customise the viewing experience.

Select speakers for movie sound

The TV automatically selects the optimal sound, when you select a source, but you can select an available speaker combination that suits the source you are using yourself.

Select picture format

The TV automatically adapts the picture to ll out as much of the screen as possible, when you select a source, but you can select a format yourself.

Bring up Scene

display on Beo5*

Bring up Scene

display on Beo5*

Standard

For panoramic view or 4:3

Select Speaker display

Select Picture display

Zoom

The picture is

adjusted ver tically

Select speaker combination*

Select format*

Mode 5 Mode 1 Mode 2 Mode 3 Mode 4

Adjust picture up or

down

Wide

For genuine 16:9

widescreen pictures

Switch to Home cinema

Move the picture from the T V screen onto a

connected projector screen.

Useful hints

*Scene menu

*Optimise and

Variation

Switch mode

Display FORMAT for picture formats and Home cinema and SPEAKER

for speaker combinations on Beo4. The speaker combination or the picture format is optimised if you press Optimise on Beo5. On Beo4 press GO. With each press on Variation

on Beo5, you select a variation of Standard. On Beo4 use or .

To switch between Home cinema and TV mode on Beo4, press LIST until

FORMAT is displayed then press 0.

Bring up Scene

display on Beo5*

Select Cinema display

Select Cinema to switch between Home

cinema and TV mode

NOTE! If you have added only two front speakers to the TV, you will only be able to choose Mode 1–3. You can add up to two BeoLab subwoofers to your T V.

Page 25

Sound type

While you watch TV, switch between available sound types.

Change sound type or language

Switch between available sound types and

languages.

Sound

Bring up sound type Press repeatedly to select

Sound

Sound type or language Store your favourite sound type when tuning in TV channels. See p. 27.

Page 26

WAKE UP TIMER

SOURCE TV

CHANNEL 21 BBC

START TIME 07:00

ON / OFF ON

store

TIMER SETUP

TIMER ON / OFF OFF

TIMER LIST

TIMER PROGRAMMING

WAKE UP TIMER 07:00

store

Wake-up Timer

You can make the TV switch on automatically via the Wake-up Timer. A

Wake-up Timer is a once only Timer which lasts for one hour and is disabled once it has been executed.

Enter a Wake-up Timer

Choose the source, channel number and start time.

Check or delete a Wake-up Timer

Check or delete the settings of a Wake-up Ti mer.

Bring up ‘T V SETUP’ menu

Select ‘PLAY TIMER’ menu

Select ‘WAKE- UP TIMER’ menu

Enter and accept settings

Change and accept

settings

Useful hints

Wake-up Timer A Wake-up Timer applies only to the TV it has been programmed on.

Make sure that the clock is set to the correct time for the Wake-up Timer to be executed correctly.

NOTE! The TV cannot be part of an ordinary Play Timer or Standby Timer until the Wake-up

Timer has been carried out or disabled.

Page 27

Play Timer

You can make your TV switch on and off automatically by setting a Play Timer

or a Standby Timer in your main room system.

Timed play and timed standby

Preset your T V to start and stop automatically at the same time and day every week.

Switch on the Play Timer

To include the TV in the Play Timer, set the Timer to ‘ON’.

Bring up ‘T V SETUP’ menu and select

‘PLAY TIMER’ menu

The source names corresponds to what the

sources are registered as in the ‘CONNECTIONS’

Bring up ‘T V SETUP’ menu

Select ‘PLAY TIMER PROGR AMMIN G’ menu

Select ‘PLAY TIMER’ menu

Select source

TV DTV DTV2 ( V.AUX) V.M EM DVD/DVD2 V.A UX2 CD N.MUSIC N.RADIO A.MEM RADIO STAN DBY

Select ‘TIMER ON/ OFF’ menu

Enter and accept settings

Select ‘ON’ and

View, edit or delete a Timer

View, edit or delete a Timer from the list of

settings you have entered.

Play Timer

Enter up to six Play Timers. Make sure that the clock is set to the correct time for the Timers to be executed correctly, see p. 52. The T V cannot be

part of an ordinary Play Timer or Standby Timer until the Wake-up Timer has been carried out or disabled.

Safety

For safety reasons, the stand will not turn if the T V is switched on by a Play

Ti mer.

Bring up ‘T V SETUP’ menu

Select ‘PLAY TIMER INDEX‘ in ‘PL AY TIMER’ menu

Select Timer

NOTE! Link room systems can perform the timed play or timed standby functions as well. However, you must programme Timers on your main room system and activate them on your link room system.

Edit settings or delete

Timer

Page 28

Scan in TV channels

Find out how to register the source of your TV signal type and how to scan in

your TV channels.

Select video signal type

If you have selected ‘TV TUNER’ in the ‘TUNER SETUP’ menu, enter the source of your T V video

signal.

Identify the cable box

If you have connected a cable box to the TV, register the connection in the ‘CABLE BOX SETUP’ menu.

Source for RF input

When you have registered the cable box, enter the output channel for the type of cable box

and test whether you can change channels.

Bring up ‘T V SETUP’ menu and select

‘OP TIONS’

Select name of cable box

Select channel

number*

Highlight ‘T V TUNER‘ in ‘TUNER SETUP’ menu

Select ‘CH TEST‘

Select signal type and accept

Test if you can

change channel

Scanning begins/

identify cable box*

Store or repeat

procedure

Useful hints

*Signal type

RF cable box

*Channel number

If you select ‘CABLE’ or ‘ANTENNA’, scanning begins immediately. If you

select ‘CABLE BOX’, register the cable box. See ‘Identify the cable box’

on this page.

Leave a connected RF cable box switched on at all times. The channel number should correspond to the output channel set on the

cable box.

NOTE! If you select ‘OFF’ for ‘TV TUNER’, you must register a source in the ‘CONNECTIONS’ menu as ‘T V’ if you wish to switch on the TV using the TV button on the remote control. See

‘Register additional equipment’ on p. 43.

Page 29

Edit scanned TV channels

Remove channels you do not use, name and ne tune channels, or re-scan to nd new channels.

Remove a channel

Remove channels from the channel list. If you

wish, you can restore channels that you have

removed.

Name a channel

You can name the TV channels.

Fine tune channel

Fine tune channels, if, for example, you wish to adjust the frequency.

Re-scan TV channels

Add new channels or update scanned channels

which, e.g., have been moved by the broadcaster. If you only wish to check for a new signal on a scanned channel that has been empty, do not re-scan all channels. Instead,

select the channel in the channel list using the

number buttons. See ‘Watch television’ on p. 4.

Bring up ‘T V SETUP’ menu

Bring up ‘T V SETUP’ menu and select

‘OP TIONS’

Select ‘EDIT CHANNELS‘ in

‘CHANNEL SETUP’

Select ‘EDIT CHANNELS‘ in

‘CHANNEL SETUP’

Select ‘FINE TUNE‘ in ‘CHANNEL SETUP’ menu

Highlight ‘T V TUNER‘ in ‘TUNER SETUP’ menu

Select channel

Select ‘CHANNEL‘

and select channel

Select source of

video signal and accept

Remove/add

Follow on-screen

instructions

Fine tune and select

sound type

Scanning begins/ identify cable box*

*Video signal

‘EDIT CHANNELS’/

’FINE TUNE’

Re-scan

If you select ‘CABLE’ or ‘ANTENNA’, scanning begins immediately. If you select ‘CABLE BOX’, register the cable box. See ‘Identify the cable box’ on p. 26. If you select ‘CABLE BOX’ or ‘OFF’ for ‘TV TUNER’ in the ‘TUNER SETUP’ menu, the ‘EDIT CHANNELS’ and ‘FINE TUNE’ menus are inaccessible. If you re-scan all channels, all channel settings you have made disappear.

NOTE! Removed channels are skipped when

you step through channels using the arrow

buttons on the remote control, but can still be selected in the channel list by pressing the channel number.

Page 30

PICTURE

BRIGHTNESS ...............

CONTRAST ...............

COLOUR ...............

TINT ...............

SIZE ...............

HOR. SIZE ...............

VERT. SIZE ...............

HOR. POSITION ...............

VERT. POSITION ...............

select

SOUND ADJUSTMENT

VOLUME ...............

BASS ...............

TREBLE ...............

SUBWOOFER ...............

LOUDNESS ON

DEFAULT VIDEO SPEAKER3

DEFAULT AUDIO SPEAKER2

store

Adjust picture and sound settings

Picture and sound settings are preset from the factory to neutral values which suit most viewing and listening situations. However, if you wish, you can adjust

these settings to your liking.

Adjust picture

Adjust brightness, colour and contrast. For information on picture format, see p. 22. Adjustments made to the ‘TINT’ setting only

apply to the current channel.

Mute the picture

Remove the picture from the screen temporarily.

Adjust sound

Preset volume, bass, treble or loudness, up to two connected BeoLab subwoofers and two default loudspeaker combinations. The contents of the ‘SOUND’ menu varies according to what you have connected to the TV. See also p. 22 about speaker combinations.

Bring up ‘T V SETUP’ menu

Bring up Scene

display on Beo5

Bring up ‘T V SETUP’ menu

Select ‘OPTIONS’ menu

Select Picture

Select ‘SOUND’ in

‘OPTIONS’ menu

Select ‘PICTURE’

Enter and accept settings

Select PictureMute to mute/restore

Select

‘ADJUSTMENT’

Enter and accept settings

Temporary settings

‘DEFAULT VIDEO’

‘DEFAULT AUDIO‘

To only store picture and sound settings until you switch off the TV, press and hold BACK instead of the centre button when you accept the settings. The speaker combination chosen in the ‘DEFAULT VIDEO’ submenu is activated automatically when you switch on a video source in the T V. The speaker combination chosen in the ‘DEFAULT AUDIO’ submenu is activated automatically when you switch on an audio source in the TV.

NTSC signal only

1080p/i signal only

VGA signal only

NOTE! Do not allow still pictures, such as logos, video games, computer images, and images displayed in 4:3 format, to be displayed on the screen for an extended period of time. This can cause a permanent after-image to remain on

the screen.

Page 31

Activate parental control

Switch on TV Parental guidelines or the MPAA rating system if available in your area. Assign an access code, which you need to enter to be able to watch a

programme or channel that has been locked.*

Assign an access code

Assign /change the access code to restrict access

to programmes /channels with broadcasted restrictions and to prevent settings from being changed by others. The default setting is 0000.

Preset TV Parental guidelines

Select one common restriction level for all categories or preset the restriction level for the

individual categories.

Preset the MPAA rating

Select and store the restriction level that you

want to impose.

Bring up ‘T V SETUP’ menu

Select ‘PARENTAL CONTROL‘ in

‘OPTIONS’ menu

Select ‘PARENTAL CONTROL‘ in

‘OPTIONS’ menu

Select ‘PARENTAL CONTROL‘ in

‘OPTIONS’ menu

Select ‘ACCESS CODE’ menu

Select ‘TV PAREN TAL GUIDELINES’ menu

Select ‘MPAA RATING’ menu

Enter default /current

code and select and

conrm new code

Enter access code and

make settings

Enter access code and

make settings

Enter the access code

When a locked programme/channel is selected, the screen goes blank, sound is shut off, and the access code must be entered. All programmes /channels become available and parental control is switched off until you switch off the TV.

*Korea

Settings

Access code

In Korea, parental control may not be supported by your programme

provider.

To change or override settings, you also need to enter the access code rst.

If an incorrect access code is entered three times, the T V automatically switches to standby.

Enter access code Select locked channel

All locked channels available

NOTE! If you have forgotten your access code,

key in 9999 three times when ‘OLD CODE’ is highlighted. This allows you to enter a new code.

Page 32

Apply Closed Captioning

Apply subtitles, or Closed Captioning, to all sources and channels. Switch Closed Captioning on or off, even if you have preset the TV to display Closed Captioning at all times.

Select type/display automatically

Select the type of Closed Captioning you wish to view and whether or not Closed Captioning should be displayed automatically.

Switch Closed Captioning on/off

Switch Closed Captioning on or off while watching a programme.

Bring up ‘T V SETUP’ menu

CC CC

See status Press again to switch on/off

Select ‘CLOSED CAPTIONING‘ in

‘OPTIONS’ menu

Select ‘DISPL AY’ and make setting

Select ‘TYPE’ and

make setting

Useful hints

Page 33

Calibrate colour accuracy of the screen

Automatic Colour Management ensures perfect colours on the screen continuosly. During calibration, a sensor arm swings down from the TV frame and an on-screen bar changes between various greyscale colours.

Automatic calibration

Approximately for every 100 hours of use, the TV will initiate a calibration automatically, when

you press the standby button.

Manual calibration

The TV must be switched on for more than two

minutes and be in T V mode for the ‘AUTO COLOUR MANAGEMENT’ menu to be available.

After manual calibration

We recommend that you let the TV perform calibration automatically, instead of manually.

Bring up ‘T V SETUP’ menu

Sensor arm retracts and TV returns to last

chosen source

Select ‘OPTIONS’ menu

Activate ‘AUTO COLOUR MANAGEMENT‘

‘CALIBRATION COMPLETE’ shortly appears on

screen

Calibration process

begins*

*Manual calibration

Calibration failed

All text is removed from the screen, the sensor arm swings down and the calibration starts. If the sensor arm does not swing down fully, the calibration is not performed and the arm is retracted if needed. If the calibration was initiated automatically, the TV will attempt to execute the calibration the next time it is switched off.

NOTE! Never switch off your system or disconnect it from the mains during calibration.

Page 34

Settings for the digital tuner

Make your own channel settings, search for channels, and apply Closed Captioning.

Make channel settings

Scan in channels, make a list of your favourite

channels, add /delete channels and see the signal strength.

Make Caption settings*

Apply Closed Captioning to all sources and channels. Select a type of Closed Captioning and whether or not Closed Captioning should be displayed automatically. Switch Closed Captioning on or off, even if you have preset the TV to display Closed Captioning at all times.

Bring up tuner menu

AUTO SCAN

FAVOURITE CHANNEL CHANNEL ADD/DELETE SIGNAL STRENGTH

Bring up tuner menu Make settings

ON/OFF

ANALOGUE MODE

DIGITAL MODE

DIGITAL FONT OPTIONS

Select ‘CHANNEL’ menu

Select channels to scan for*1

Make a list of your favourite channels Add/delete a channel to/from the main list See the strength of the received signal

Select ‘CAPTION’ menu

Select if Closed Captioning should be displayed Select the mode to use for Closed Captioning in your

analogue T V receiver, and if the Closed Captioning function

is set to ‘ON’ Select the mode to use for Closed Captioning in your digital TV receiver, and if the Closed Captioning function is set to

‘ON’

Set your preferences for the digital font if you have set the

Closed Captioning function to ‘ON’

Make settings

Useful hints

*Scan channels

Favourite list

Deleted channel

*Korea

When you scan in channels, the current channel/favourite lists will be lost. To nd out which signal type to use, contact your cable provider. If you have not made a favourite list, the main list appears when you press

List.

When a channel is deleted, it is removed from the channel sequence, but it can still be reached if you enter the channel digits. The ‘CAPTION’ menu is not available in Korea.

NOTE! If you press CC repeatedly, you change the mode or switch Closed Captioning on or off, even if you have preset the function to ‘ON’. On

Beo4 use TEXT.

Page 35

Restrict access to particular channels or rated contents and enter information

on the current terrestrial and cable setup.

Make V-Chip settings*3

Lock specic TV contents to avoid others from

watching it. To access locked contents, you

need to enter your V-Chip pincode after which all locked contents will be available until you switch off the TV. The default setting is 0000. Restriction of access in the ATSC tuner and the

TV tuner is set independently of each other, see

also p. 29.

Set up personal preferences*4

Set up your personal preferences, such as menu language. When you select a preferred language for audio, this language will be used when available from the programme provider.

Bring up tuner menu Make settings

CHANGE PIN US RATING SETTING

CANADIAN RATING SETTING

DOWNLOADABLE RATING SETTING

Bring up tuner menu Make settings

TIME > DAYLIGHT SAVING > TIMEZONE SOUND > MULTI-TRACK SOUND > DIGITAL OUTPUT MENU LANGUAGE VERSION INFORMATION

Select ‘V-CHIP’ menu

Enter a new V-Chip pincode twice Apply the MPAA rating system/TV-PG system as parental

control

Apply the English/French classification system as parental

control

See downloaded rating settings, if available

Select ‘SETUP’ menu

Select whether to use daylight saving or not and set the local

information for the clock

Select the audio language to be used, if available from the programme provider, and select the sound output

Select the language to be used in menus See the current ATSC tuner version, model and release date

*Korea

V-Chip

*Korea

Daylight saving

The ‘V-CHIP’ menu is not available in Korea. To change settings in the ‘V-CHIP’ menu, enter the V-Chip pincode.

In Korea only ‘MULTI-TR ACK SOUND’, ‘DIGITAL OUTPUT’ and ‘VERSION INFORMATION’ are available.

‘DAYLIGHT SAVING’ only works, if the programme provider’s daylight

saving ag is set to ‘ON’ and ‘DAYLIGHT SAVING’ is set to ‘YES’.

NOTE! If you have forgotten your V-Chip pincode, enter the ‘V-CHIP’ menu and key in

9999. This allows you to enter a new code.

Page 36

The pincode system

The pincode system prevents people who do not know the pincode from using

the TV. When the pincode system is activated and the TV has been disconnected from the mains for 15–30 minutes, the system goes into effect.

Activate the pincode system

Enter a four digit pincode to activate the system.

Change the pincode

Change the pincode you have chosen.*1

Delete the pincode

Delete the pincode you have chosen.

Enter the pincode

If you cannot switch on the T V after disconnection from the mains, wait 30 seconds

and try again.

Bring up ‘T V SETUP’ menu

Press twice

Accept Enter pincode

STOP

Press

STOP

Press

STOP

Press

Enter a four digit

code and accept

Enter pincode, accept and select

‘NEW PINCODE‘

Enter pincode and accept

Re-enter the code

and accept

Enter new code, accept, re- enter code and accept

Select ‘DELETE

PINCODE’ and accept

If you forget the pincode

Contact your Bang & Olufsen retailer to receive a ve digit mastercode.

Useful hints

*Change of pincode

Incorrect pincode

If you change your pincode more than ve times within a three-hour period, the ‘PINCODE’ menu becomes inaccessible for three hours, assuming that the TV is not disconnected from the mains. Five incorrect entries will cause the TV to shut down for three hours, during which operation is not possible. Disconnecting the TV resets the

three-hour period.

Hold when prompted for pincode to display ve elds*

Enter ve digit mastercode

Accept to delete pincode, you can now activate pincode system again

NOTE! If you are prompted for a pincode the rst time you switch on your TV, contact your Bang & Olufsen retailer.

To cancel a pincode entr y and clear the input

elds, press BACK. On Beo4, press STOP.

* On Beo4 hold to bring up the ve elds.

Page 37

Tuner setup

Disable the TV or ATSC tuner, if your TV or ATSC source is a peripheral unit, such as a set-top box.

Disable the internal tuner

If you disable the TV tuner, you can activate a connected peripheral unit with the TV button. If you disable the ATSC tuner, you can activate

a connected peripheral unit with the DT V

button. In this menu you can also scan in channels or identify a cable box you may have

connected to the TV.

Bring up ‘T V SETUP’ menu

Contents of the

‘TUNER SETUP’ menu

Select ‘TUNER SETUP‘ in

‘OPTIONS’ menu

TV TUNER

ATSC

Select ‘TV TUNER’ and make settings*1

Register the source of your T V video signal. It is not required during first-time setup. Options are ‘CABLE’, ‘CABLE BOX’, ‘ANTENNA’, and

‘OFF’

Disable/enable the ATSC tuner

Disable/enable ‘ATSC‘

and accept

*‘TV TUNER’

settings

Disable TV/ATSC

tuner

If you select ‘CABLE BOX’, follow the on-screen information to specify which cable box you have connected to the T V. If you select ‘ANTENNA’ or

‘CABLE’, a scanning process begins when you store the setting.

If you disable both the T V tuner and the ATSC tuner, you can activate a peripheral unit acting as tuner with either the TV button or the DTV button.

NOTE! For more information about the ‘TUNER SETUP’ menu and about scanning TV channels, see ‘Scan in TV channels’ on p. 26.

Page 38

PROGRAM GUIDE

RADIO/TV MODE

INFORMATION

PROGRAM GROUPS

SUBTITLE LANGUAGE

AUDIO LANGUAGE

SETUP

PROGRAM LIST

Operate other equipment with Beo5 or Beo4

The built-in Peripheral Unit Controller acts as an interpreter between connected

video equipment, such as a set-top box, recorder or DVD player, and your Bang & Olufsen remote control.

Beo5 operation

The main functions of your equipment can be operated with the Bang & Olufsen remote control. Not all functions may be supported.

Show menu overlay*1

If you have a Beo4, the menu overlay gives you quick access to selected functions.

Direct Beo4 operation

Activate a function without the menu overlay. The connected equipment must be switched on.

Select source

Select connected

equipment

Press coloured button to activate function

Select function

Bring up menu overlay

Select channel

Select function

Hold for Programme Guide

Useful hints

*Menu overlay The menu overlay shows the options you have with a selected source. You

can only bring up the menu overlay on the TV screen with a Beo4. With a Beo5 you have access to the corresponding functions via the Beo5 display. You cannot bring up the overlay in link rooms. Instead, press a desired coloured button or GO followed by a number.

NOTE! Which source button activates your

peripheral unit depends on the tuner setup and

settings in the ‘CONNECTIONS’ menu. See pp. 35 and 43.

Page 39

Use the Bang & Olufsen remote control to gain access to the functions offered by your non-Bang & Olufsen equipment.

Use equipment menus

Operate a connected equipment’s own menu via the remote control. On Beo4 you may have to press EXIT instead of STOP to return to a previous menu.

Video recorder/DVD player

Switch on equipment, start and stop playback, and search back and forth.

Record here and now

Make an immediate recording of a programme from any source/channel. Watch what you are

recording, select another source, or switch the

TV to standby – the recording continues. To

ensure a successful recording, make sure that the video recorder is set to the correct input. If you attempt to switch to another TV source while recording, ‘RECORD’ appears on the

screen.

Bring up equipment menu

Switch on

equipment

Record

Press twice Press twice to stop recording

Navigate in menus

Backwards/

forwards

Select source

Select function Step in pages/

STOP PLAY

Once to pause Twice to stop

Select video recorder

channel lists*

Resume playback

STOP

Enter information

0–9

Record from video recorder tuner

Channels you wish to record must be stored in

the video recorder tuner, as well as in the TV’s

tuner. The recording is controlled by the video

recorder. To ensure that recording takes place,

remember to set the input selector correctly on the video recorder. For more information about

recording, see the video recorder’s own guide.

*Beo4

Switch on or off

Record on a second

recorder

On Beo4 you have to press GO before the arrow buttons. On some connected equipment you have to press GO then 0 to switch the

equipment on and off if you have a Beo4.

To make a recording on a second video recorder connected to the AV2

socket area, press Record2 on Beo5. To stop the recording, press Record2

then STOP t wice.

Select video recorder

Record

Press twice

You can switch

to standby/return

to recording

NOTE! See also the guide enclosed with the connected equipment. For further information about supported equipment, contact your Bang & Olufsen retailer.

STOP

Press twice to stop recording

Page 40

Page 41

Contents – Installation

40 Set up your television

42 Expand your setup

44 Set up additional equipment

46 Connection panels

48 First-time setup of your television

50 Loudspeaker setup

52 Additional settings

54 On-screen menus

54 Cleaning

Set up your television • Expand your setup • Set up additional equipment • Connection panels • First-time setup of your television … Installation – Setup

Page 42

Place the TV

When you place the TV, remember that the builtin motor unit will turn the TV to a preset position

when you switch it on.

Remove supports

When you have placed the TV, remove the two supports beneath the front frame.

Set up your television

Follow the guidelines for placement and connection described on this and the following pages.

Due to the heavy weight of the T V, any moving or lifting of the TV should be performed by qualied personnel – using the proper equipment.

Unscrew the screws inside each support.

Fasten base cover

The cover has strips of double-coated tape on the back.

Important

Ventilation

Before you fasten the cover permanently, try to put it into place without removing the tape backing.

To ensure proper ventilation, allow for at least 2” (5 cm) of space on each side of the TV and 4” (10 cm)

above it. Do not cover the ventilation holes on the rear. At overheating (ashing standby indicator and an on-screen warning), switch off the T V to let it cool.

You cannot operate the T V during this time.

Page 43

Run cables

To allow for the movement when the TV turns, the

cables must form a broad loop and be fastened to the cable bracket.

Overview

Locate the connection panels and other important items:

1 Standby indicator/receiver for remote control. 2 Side connection panel (input for mains supply,

aerial input for T V signal, connections for BeoMaster).

Tilt the main connection panel (4) forward to

get acces to the sockets.

3 Cable bracket. 4 Main connection panel with built-in tray and

cover for cables.

Tilt the panel forward to remove cover.

Open tray along the side to ease access when

running cables.

To decide how much ‘slack’ the cables need,

gently turn the TV all the way to the left, before you fasten the cables with cable strips to make a

‘neat’ bundle of cables.

Page 44

Expand your setup

Your TV supports a wide range of additional equipment. You can even connect a

projector or a home automation system to control room lights and curtains. Connect video recorders only to AV1 or AV2.

Disconnect from the mains

While expanding your setup, the TV must be disconnected from the mains.

Remove the cable cover

Remove the cable cover to get access to the

connection panel.

Connect additional equipment

To operate non-Bang & Olufsen products with Beo5, attach a Bang & Olufsen IR-transmitter to each product. See also pp. 44-45.

Tilt main connection panel

forward

Select corresponding socket

marked CTRL

Disconnect TV from mains Switch off TV

Release the two locks A and pull off cover

Make the connections

Press B to open the small door to

sockets for temporary

connections

Switch on the TV

Always attach covers before you connect the T V to the mains.

Information

‘AUTO SELECTION’

‘TIMER RECORDER’

‘HDMI’

Connect TV to mains supply Attach all covers

Automatic selection of connected sources, when the TV is on and detects a signal. Activate the Timer recording option for a connected recorder. Only available in the ‘AV1’ and ‘AV2’ menus, and can only be activated in one of these menus at any time.

Equipment connected via an HDMI IN socket. If you have set the ‘HDMI EXPANDER’ in the ‘CONNECTIONS’ menu to ‘YES’, the ‘HDMI-C’ option in the ‘AV’ menus is replaced with ‘HDMI-C1’, ‘HDMI -C2’, ‘HDMI-C3’, and ‘HDMI-C4’.

Switch on TV

Page 45

TV. Repeat the procedure for each socket group.

Bring up ‘T V SETUP’ menu

Contents of the

‘CONNECTIONS’

Source options in

the ‘AV1–AV6’

menus

Select

‘CONNECTIONS’

in ‘OPTIONS’ menu

AV1–AV6 DISPLAY 2 HDMI EXPANDER

LINK

NONE V.M EM DVD/DVD2 DTV2 ( V.AUX) DTV V.A UX2 TV PC CENTRE

Select sockets in a socket group and

Register connected equipment Register a connected projector Enable or disable an HDMI Expander connected to the HDMI C socket Set a link channel and enable the system modulator

Nothing connected Connected video or hard disc recorder Connected DVD player or recorder Equipment, such as a set-top box ATSC digital tuner Equipment, such as a video game console Connected T V tuner BeoMaster or connected PC For connection of a source centre, which may contain up to six built-in sources (only in the ‘AV2’ menu)

Select ‘STANDBY OPTIONS’ menu

Follow on-screen

instructions

‘(VGA)’

‘STANDBY OPTIONS’

The above are only examples of registrations, you can

register available equipment to any source option. You may also have to register additional equipment in the Master Link system.

Equipment connected via VGA socket (AV5, available if you do not have the optional BeoMaster, or AV6). Set the set-top box to switch off when you switch source or when you switch off the TV. You can also choose that the set-top box should always be switched on or that it should be switched on and off manually by means of the remote control.

Page 46

POWER LINK 1

SUB

POWER LINK

2–6

Cable network

ANT 2

ANT 1

HDMI IN

(A–D)

AV (1–6)

Digital cable/

HDTV box

ATSC TV signal

Analogue TV signal

AV 6

AV 3

AV 2

AV 1

Camera

[CAMERA]

DVD

[DVD]

Digital TV

[DTV]

PVR Box

[V MEM]

Video signals

Connect your video signals, such as a cable,

antenna, or satellite to the sockets shown on the

diagram to the right.

Loudspeakers

Use Bang & Olufsen Power Link speakers. Use the cables enclosed with the speakers. Longer cables are available from your Bang & Olufsen retailer.

Set up additional equipment

Set up the TV with video sources and loudspeakers.

Additional video equipment

Connect many different types of video equip ment at the same time. Here you can also see examples of source names you can select for the equipment in the ‘CONNECTIONS’ menu.

Useful hints

Equipment with HDMI output Equipment with HDMI output can be connected to any available HDMI sockets, regardless of the

IR-transmitters: To operate non-Bang & Olufsen products with a Bang & Olufsen remote control, attach a Bang & Olufsen IR-transmitter to each of the products. Connect each transmitter to the corresponding socket marked CTRL on the main

connection panel.

particular AV socket group to which you have connected the equipment. For more information about how to set up connected equipment for use, see p. 43.

Page 47

Home cinema setup

Ethernet

USB

ROUTER

Internet

DISPLAY 2

IR 1+2

IR-IN

CINEMA

Home

Automation

system

Use a projector or connect a home automation system to the TV, so you can control room lights

and curtains.

IR-receiver

If the built-in IR-receiver for the remote control signals is hidden behind a lowered projector screen, you must set up an external IR-receiver as

well.

Expand your setup, for example in a home cinema system with a projector and a home automation system.

BeoMaster

If your TV is equipped with a BeoMaster, use the Ethernet socket on the side connection panel for connection to the Internet, and the two USB sockets to connect extra equipment to the BeoMaster, for example a memory card reader.

Audio system

Connect a Bang & Olufsen audio system with a Master Link socket to your TV. Connect it to the

Master Link socket on the side connection panel.

Connection panels

Any equipment you connect to the main connection panel must be registered in the ‘CONNECTIONS’ menu. See p. 43.

For a compatible Bang & Olufsen audio system. Available only if the TV has a BeoMaster.

Useful hints

HDMI source You can watch two HDMI sources at the same time if one of the sources is

USB

For connection of USB-enabled equipment. Available only if the TV has a BeoMaster.

Ethernet*

For connection to the Internet. Available only if

the TV has a BeoMaster.

~ – Mains supply

Connection to the mains supply.

connected to the HDMI A or HDMI B socket, and the other source is connected to the HDMI C or HDMI D socket.

*NOTE! Only connect to a local area network

(LAN) that does not exit your at, house or

building.

Page 49

“Greyed out” sockets on the illustration of the main connection panel may be occupied by internal connections. Do not

disconnect the cables from these sockets!

Connect stereo headphones.

AV1

Socket group for AV connection of a primary video recorder, set-top box, or other types of extra video equipment.

AV2

Socket group for AV connection of additional video equip ment.

AV3

Socket group for AV connection of additional video equip ment.

The TV keeps a signal path open between a

recorder connected to the AV1 socket area and a recordable source connected to the AV3 socket

area.

This allows you to set the source on AV3 to switch

on automatically, as well as set a recorder on AV1 for timed recording of the source on AV3, provided your connected equipment supports these functions.

AV4

Socket group for AV connection of additional video equipment.

AV5

This socket group is only available if your TV is not

equipped with a BeoMaster. Use this socket group for equipment which you do not wish to have permanently connected, e.g. a camera or a ca mcord er.

AV6

Use this socket group for equipment which you do not wish to have permanently connected, e.g. a camera or a camcorder.

VIDEO IN ( AV1– AV6) For video signal.

VIDEO OUT (AV1–AV 2) For a video recorder.

L-IN, R-IN (AV1–AV6) Right and left line input.

L–R OUT ( AV1– AV2) Right and left line output.

Y – Pb – Pr (AV 2– AV3)

For video signals from an external source, e.g. HDTV source. You can use the socket in conjunction with an AV socket or a digital audio

socket.

SPDIF (AV1– AV6) Digital audio input socket, e.g. DVD player.

CTRL (AV1–AV6) For IR control signals to external equipment connected to an AV socket.

S VIDEO (AV4, AV6) For S-VHS or Hi-8 Camcorders.

DISPL AY 2 (DVI-D OUT) Connect a projector.

HDMI IN (A– D) For High Denition Multimedia Inter face video source or PC. The sources can be registered to any of the AV socket groups. Connect an HDMI Expander to the HDMI C socket.

VGA

Socket for connection of a High Denition video source or a PC.

ANT (1–3) Aerial input socket (1) for future use (2) for ATSC tuner (3) from external aerial/cable T V network.

MASTER LINK

For a compatible Bang & Olufsen audio system. Available if the T V does not have a BeoMaster.

DTV DATA

For future use.

CINEMA

For a Home Automation System.

TTL /RS232

Only for use in Hotel setups.

IR IN

For an extra IR-receiver when the TV is set up with

a projector.

IR 1+2

For an external IR-transmitter used with Home cinema setups.

Headphones

POWER LINK 1 (SUB)

POWER LINK 2–6

To mute speakers turn the volume wheel quickly counter-clockwise. Turn the volume wheel either way to adjust volume in headphones. To restore sound in speakers, turn the volume wheel quickly counter-clockwise. Use a cable splitter to connect two Bang & Olufsen subwoofers. For external speakers in a surround sound setup. See also pp. 50–51.

NOTE! Video recorders can only be connected to the AV1 and AV2 socket groups, as these are the only sockets groups for video output. Connect the primary recorder to AV1 and the secondary recorder to AV2.

Page 50

First-time setup of your television

This rst-time setup procedure is activated when the TV is connected to the mains

and switched on for the rst time. If you want to change your setup at a later date, you can access the same menus and update your settings.

Switch on the TV

It takes the T V approx. 20 seconds to start up and become ready for use.

Make settings

You are led through the following settings only when you switch on the TV for the rst time.*2

Switch on

Select setting Accept and go to next menu item

TUNER SETUP

CONNECTIONS

Disable or enable internal T V tuner or ATSC, see p. 35*1 Register connected equipment, see p. 43

Information

*TV tuner

Connections

If you select ‘CABLE BOX’, follow the on-screen information to specify which

cable box you have connected to the TV. If you select ‘ANTENNA’ or ‘CABLE’, a scanning process begins when you store the setting. Select the type of equipment connected to each socket, the sockets used, the product name, and the source name.

* NOTE! When you have made the preferred settings in a menu, you may have to press the green button to continue to the next menu in the

rst-time setup procedure. Follow on-screen

instructions.

Page 51

When rst-time setup is complete, you can then set up your loudspeakers for Home cinema use.

Calibrate the speakers

Set up the speakers to optimise sound from your

listening position.

Calibrate the stand

The motorised movement of the TV will not work

until the calibration process has been completed.

SPEAKER TYPES SPEAKER ROLES SPEAKER DISTANCE SPEAKER LEVEL

SOUND ADJUSTMENT

STAND ADJUSTMENT

First-time setup of loudspeakers applies only to speakers for TV viewing.

After rst-time setup, you can set up speakers for Home cinema viewing.

See also ‘Loudspeaker setup’ on pp. 50–51 and ‘Surround sound and Home cinema’ on p. 22.

Adjust volume, bass, treble and loudness and preset two default speaker

combinations. Select a different speaker combination at any time. See p.28.

At ‘SET LEF TMOST

POSITION’ turn left to the

point you wish to restrict

the movement to

At ‘SET RIGHTMOST

POSITION’ turn right to the

point you wish to restrict the

movement to

STAND POSITIONS

Stand adjustment Set the maximum angle the T V will turn – left and right.

Set preferred preset position for the T V to turn to, when it is switched

on and off. See p. 52.

NOTE! You need to calibrate the stand before you can use the motorised movement of the stand.

Page 52

Loudspeaker setup

Add Power Link speakers and up to two BeoLab subwoofers to your TV and you have a surround sound system.

Select speaker setup

Switch on the TV in TV or Home cinema mode before you adjust speaker settings for either mode.

Set speaker type

is highlighted on the screen.

Set speaker role

Select the function for each connected loudspeaker, such as front, back or surround. A speaker can have more than one role – one for TV viewing and one for Home cinema viewing.

Switch on TV and bring up ‘TV SETUP’ menu

Select ‘SPEAKER TYPES’ menu

Select ‘SPEAKER ROLES’ menu

Select ‘SOUND’ in ‘OPTIONS’ menu

Select speaker and reveal speaker type

Reveal speaker role for each

speaker

TV (1) Home cinema (2)

A: Right front Left front B: Left front Left surround C: Off Left back D: Off Right back E: Left back Right surround

F: Right back Right front

G: Off Centre

Select menu

Set speaker role.

Information

Sound during setup

Speaker roles

During the setup process, a sound is sometimes produced by a speaker. Check if the highlighted speaker matches the name of the speaker making the sound.

You must select the surround speakers before you can select the back

speakers.

NOTE! To make a Home cinema setup, you must

rst switch to Home cinema mode. For

information about Home cinema, see p. 22.

Page 53

If your setup includes two different viewing positions, a Home cinema setup and a

CENTRE

LEFT

FRONT

RIGHT FRONT

LEFT SURROUND

RIGH

SURROUND

RIGHT BACK

LEFT

BACK

regular TV viewing setup, you must make two different loudspeaker settings.

Set speaker distance

Enter the straight-line distances in metres between your favourite viewing position and the

individual speakers.

Calibrate the sound level

A calibration sound is produced alternately in each

speaker. Adjust the speakers to match the centre

speaker’s sound level.

See active sound system

See the name of the active sound system for a source or programme on the screen.

Select ‘SPEAKER DISTANCE’ menu

Select ‘SPEAKER LEVEL’ menu

Bring up ‘T V SETUP’ menu

Select speaker and select distance

Select ‘AUTOMATIC’ or ‘MANUAL’ in

‘SEQUENCE’

Select ‘SOUND’ in

‘OPTIONS’ menu

If ‘MANUAL’ is

selected, select speaker and adjust level

Select ‘SOUND SYSTEM’ menu

Set speaker distance. Calibrate sound level from two different viewing

Speaker level Calibrate each speaker in reference to the centre speaker to ensure an optimal

surround sound.

positions.

NOTE! Once you have performed the speaker calibration, you will only need to re-calibrate the speaker sound if you make changes to the setup.

Page 54

STAND POSITIONS

VIDEO

AUDIO

STANDBY

STAND ADJUSTMENT

select

CLOCK

TIME 20:00

DATE 23

MONTH APR

YEAR 2009

store

Additional settings

You have the possibility to make additional settings, such as to set the positions for

the TV to turn to, and to set the correct time and date.

Positions of the TV

Programme a position for when you watch TV, listen to music, and when the T V is switched off. See p. 49 about rst-time installation of the

stand.

Time and date

Set the time and date. Press Clock on Beo5 to bring up the clock on the display. It disappears again after 10 seconds.

Bring up ‘T V SETUP‘ menu and select

‘STAND POSITIONS’

Bring up ‘T V SETUP‘ menu and select

‘OPTIONS’ menu

Select ‘VIDEO‘, ‘AUDIO‘ or ‘STANDBY’

Select ‘CLOCK’

Turn TV as desired

Set time and date

Accept*1

Information

*First-time setup During rst-time setup, when you have set the TV positions, press the green button to continue rst-

time setup.

Page 55

Page 56

On-screen menus

General settings: Select your Zone, TV and Menu.

1. 2.

CHANNEL SETUP

PLAY TIMER

OPTIONS

STAND POSITIONS

EDIT CHANNELS p.27 FINE TUNING p.27

TIMER ON/OFF p.25

PLAY TIMER INDE X p.25 PLAY TIMER PROGR AMMING p.25 WAKE-UP TIMER p.24

CONNECTIONS

TUNER SETUP

SOUND

PICTURE p.28

CLOSED CAPTIONING p.30

PARENTAL CONTROL

CLOCK p.52

VIDEO p.52 AUDIO p.52

STANDBY p.52 STAND ADJUSTMENT p.49

Make settings

AV1–AV6 p.43 DISPLAY 2 p.43 HDMI EXPANDER p.43 LINK p.43

TV TUNER p.35 ATSC p.35

SOUND ADJUSTMENT p.28 SPEAKER TYPES p.50 SPEAKER ROLES p.50 SPEAKER DISTANCE p.51 SPEAKER LEVEL p.51 SOUND SYSTEM p.51

TV PARENTAL GUIDELINES p.29 MPAA RATING p.29 ACCESS CODE p.29

Cleaning

Maintenance

Screen

Cabinet and controls

Never alcohol

Regular maintenance, such as cleaning, is the responsibility of the user. Use a soft, dry cloth to wipe dust off the screen. Do not use liquid cleaners or aerosol cleaners. Wipe dust off the surfaces using a dry, soft cloth. To remove stains or dirt, use a soft, damp cloth and a solution of water and mild detergent, such as washing-up liquid. Never use alcohol or other solvents to clean any parts of the TV.

Page 57

American digital tuner settings: Select your Zone, the digital tuner source and Menu.

1. 2.

CHANNEL

CAPTION

V-CHIP*1 (ENTER YOUR PIN)

SETUP

AUTO SCAN

FAVOURITE CHANNEL p.32 CHANNEL ADD/DELETE p.32 SIGNAL STRENGTH p.32

ON/OFF p.32 ANALOGUE MODE p.32 DIGITAL MODE p.32 DIGITAL FONT OPTIONS p.32

CHANGING PIN p.33 US RATING SETTING p.33 CANADIAN RATING SETTING p.33 DOWNLOADABLE RATING SETTING p.33

TIME

SOUND

MENU LANGUAGE

VERSION INFORMATION p.33

Make settings

AIR p.32

CABLE AUTO p.32 CABLE STD p.32 CABLE HRC p.32 CABLE IRC p.32

DAYLIGHT SAVING p.33

TIMEZONE p.33

MULTI-TRACK SOUND p.33 DIGITAL OUTPUT p.33

ENGLISH p.33 SPANISH p.33 FRENCH p.33

Korean digital tuner settings: Select your Zone, the digital tuner source and Menu.

1. 2.

CHANNEL

SETUP

*V-Chip The ‘V-CHIP’ menu within the ATSC tuner menu allows you to restrict access

to particular channels or rated contents. Restriction of access in the ATSC tuner and in the T V tuner is set independently of each other.

AUTO SCAN

FAVOURITE CHANNEL p.32 CHANNEL ADD/DELETE p.32 SIGNAL STRENGTH p.32

MULTI-TRACK SOUND p.33 DIGITAL OUTPUT p.33 VERSION INFORMATION p.33

Make settings

AIR p.32

CABLE p.32

NOTE! The structure of the digital tuner menu system may change with new software.

Page 58

Safety copy and anti-virus program

Always keep copies of your data to ensure that your photos, music les, etc. are not

lost in the event of a system or program failure. The BeoMaster features an anti-

virus program that blocks the most common computer viruses.

Safety copy

It is the responsibility of the user to regularly make safety copies of the data, including but not limited

to les, photos, music, etc. It is the responsibility

of the user to ensure that this data is available on media which can be immediately transferred back

to the BeoMaster or in the event that the

BeoMaster is replaced, to the new BeoMaster, and

it is the responsibility of the user to reinstall these safety copies when necessary.

A safety copy may be placed on your ofce

computer or any other external devices, such as a portable hard disk, or the data may be copied to

CD-roms or DVD discs.

Data must also be safety copied when handing in

the BeoMaster for service. Often it will be

necessary to format data media as par t of the repair and such formatting with the consequential loss of data will take place without notice. Bang & Olufsen cannot be held liable for any loss of data.

Re-installation of data

In case you need to re-install your media collection on the BeoMaster, you must use BeoPlayer, BeoPort or BeoConnect (for MAC users only) software to transfer your collection to the

BeoMaster. This ensures that you will not lose the

associated tag information.

Anti-virus program

A virus attack can result in system breakdown and

loss of important data. In serious cases the BeoMaster may have to be handed in for service. A repair caused by a virus attack is NOT covered

by guarantee. The BeoMaster features an antivirus program. The program protects against the

most commonly used hacker programs. The

program is automatically updated for a least ve

years via the Internet provided that the BeoMaster is constantly connected to the Internet. The

program is installed to instantly and without

notication remove all les containing a virus. Files transferred to the BeoMaster may be deleted as a

result.

Bang & Olufsen cannot be held liable for an loss as a consequence of virus attack.

Page 59

End User Licence Agreement – EULA

On the BeoMaster a limited edition of Windows XP® is embedded. To use this edition, you must read the EULA terms below.

EULA Terms

You have acquired a device, a BeoMaster, that

includes software licensed by AmiTech from Micro soft Licensing, GP or its afliates. Those installed software products of MS origin, as well as associated media, printed materials, and online or electronic documentation, are protected by

inter national intellectual property laws and treaties.

The SOFTWARE is licensed, not sold. All rights

reserved.

IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT EULA, DO NOT USE THE DEVICE OR COPY THE SOFTWARE. INSTEAD, PROMPTLY CONTACT AMITECH FOR INSTRUCTIONS ON RETURN OF THE UNUSED DEVICE; FOR A REFUND. ANY USE OF THE SOFTWARE, INCLUDING BUT NOT LIMITED TO USE ON THE DEVICE, WILL CONSTITUTE YOUR AGREEMENT TO THIS EULA (OR RATIFICATION OF ANY PREVIOUS CONSENT).

GRANT OF SOFTWARE LICENSE. This EUL A grants you the following license: You may use the SOFTWARE only on the DEVICE.

NOT FAULT TOLERANT. THE SOFTWARE IS NOT FAULT TOLERANT. AMITECH HAS INDEPENDENTLY DETERMINED HOW TO USE THE SOFT WARE IN THE DEVICE, AND MS HAS RELIED UPON AMITECH TO CONDUCT SUFFICIENT

TESTING TO DETERMINE THAT THE SOFTWARE IS

SUITABLE FOR SUCH USE.

Limitations on Reverse Engineering, Decompilation, and Disassembly. You may not reverse engineer, decompile, or disassemble the SOFT WARE, except

and only to the extent that such activity is expressly

permitted by applicable law notwithstanding this limitation.

SOFTWARE TRANSFER ALLOWED BUT WITH RESTRICTIONS. You may permanently transfer rights under this EULA only as part of a permanent sale or transfer of the Device, and only if the reci pient agrees to this EULA. If the SOFT WARE is an upgrade, any transfer must also include all prior versions of the SOFTWARE.

EXPORT RESTRICTIONS. You acknowledge that SOFTWARE is subject to U.S. export jurisdiction.

You agree to comply with all applicable interna tio-

nal and national laws that apply to the SOFT WARE, including the U.S. Export Administration Regulations, as well as end-user, end-use and destination restrictions issued by U.S. and other governments. For additional information see http://www.microsoft.com/exporting/

NO WARRANTIES FOR THE SOF TWARE. THE SOFT WARE is provided AS IS and with all faults. THE ENTIRE RISK AS TO SATISFACTORY QUALIT Y, PERFORMANCE, ACCURACY, AND EFFORT (INCLUDING LACK OF NEGLIGENCE) IS WITH YOU. ALSO, THERE IS NO WARRANTY AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THE SOFTWARE OR AGAINST INFRINGEMENT. IF YOU HAVE RECEIVED ANY WARRANTIES REGARDING THE DEVICE OR THE SOFTWARE, THOSE WARRANTIES DO NOT ORIGINATE FROM, AND ARE NOT BINDING ON, MS. No Liability for Certain Damages. EXCEPT AS PRO HIBITED BY LAW, MS SHALL HAVE NO LIABILITY FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE SOFT WARE. THIS LIMITATION SHALL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL PURPOSE. IN NO EVENT SHALL MS BE LIABLE FOR ANY AMOUNT IN EXCESS OF U.S. T WO HUNDRED FIFTY DOLLARS (U.S. $250.00)

Page 60

Manufactured under license from Dolby

Laboratories. Dolby, Pro Logic, and the

double-D symbol are registered trademarks of

Dolby Laboratories.

Condential unpublished works.

Manufactured under license under

U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380;

5,978,762; 6,487,535; 7,003,467; 7,212,872 &

other U.S. and worldwide patents issued &

pending.

DTS, DTS Digital Surround, ES, and Neo:6 are

registered trademarks and the DTS logos, and

Symbol are trademarks of DTS, Inc.

This product incorporates copyright protection

tech nology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

HDMI, the HDMI logo and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

Acknowledgements and liability

Product names mentioned in this guide may be trade marks or registered trademarks of other companies.

Portions utilize Microsoft Windows Media

Windows Media and the Windows Logo are

registered trade marks of Microsoft Corporation in the United States and/or other countries.

The internal antennas used for this mobile

transmitter must provide a separation distance of

at least 20 cm (8") from all persons, and must not

be co-located or operating in conjunction with

any other antenna or transmitter.

Modications not expressly approved by this

company could void the user’s authority to

operate the equip ment.

NOTE: This device complies with part 15 of the

FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause

harmful interference, and (2) this device must

accept any inter ference received, including

interference that may cause undesired operation.

Please note that Bang & Olufsen will, in no event, be liable for any consequential, incidental or indirect damages arising out of the use or inability to use the software.

Page 61

For the US market only!

NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harm ful interference in a

residential installation.

This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equip ment off

and on, the user is encouraged to try to correct

the interference by one or more of the following

measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment

and receiver.

– Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

– Consult the retailer or an experienced radio/TV

technician for help.

For the Canadian market only!

This class B digital apparatus meets all require-

ments of the Canadian Interference-Causing Equip ment Regulations.

Page 62

Page 63

Page 64