AT&T 9312 User Manual

900 MHz Two-Line Cordless

Speakerphone 9312

Please also read

Part 1 — Important

Product Information

USER’S MANUAL

Par t 2

AT&T and the globe symbol are registered trademarks of AT&T Corp.licensed to Advanced American Telephones.

Printed in China. 850004334 Issue 1AT&T 8/00

CONTENTS

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . 3

Before You Begin........................... 3

Table/Desk Installation...................5

Wall Installation ............................ 6

TELEPHONE OPERATION

AT THE HANDSET . . . . . . . . . . . . . . . . . . . . . . . 9

Make a Call.................................... 9

Answer a Call................................ 9

End a Call.......................................9

Flash/Call Waiting.......................... 9

Change Channel............................ 9

Redial ............................................ 9

Hold .............................................. 9

Handset Volume............................ 9

Temporary Tone Dialing.............. 10

Handset Ringer Style ................... 10

Ringer Off ................................... 10

Intercom Calls............................. 11

Conference Calls ......................... 11

Switching from Handset to

Base Speakerphone ................. 12

Headset Jack................................ 12

Operating Range......................... 13

TELEPHONE OPERATION

AT THE BASE . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Make or Answer a Call................ 14

Flash/Call Waiting........................ 14

Mute............................................ 14

End a Call.................................... 15

Base Ringer Volume..................... 15

Redial .......................................... 15

Hold ............................................ 15

Speakerphone Volume ................ 15

Intercom Calls............................. 16

Switching from Base

Speakerphone to Handset....... 16

TELEPHONE MEMORY . . . . . . . . . 17

Store Memory Numbers.............. 17

Store a Pause in a

Memory Number..................... 17

Change/Replace a

Stored Memory Number .......... 17

Dial Memory Numbers ............... 17

BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . 18

Charging the Handset

Battery Pack............................. 18

Replacing the Handset

Battery Pack............................. 19

Spare Battery Charger..................20

IN CASE OF DIFFICULTY . . . . . . 21

Before You Install

1 Choose a location for the base near an electrical outlet and a

telephone jack.

This phone requires a modular telephone jack and a standard electrical outlet (110v AC) not controlled by a wall switch.

2 Install the handset battery.

INSTALLATION

b) Plug battery

pack connector into handset.

d) Replace cover by

sliding it up into place.

a) Remove battery

compartment cover by pressing on the indentation and sliding downward.

c) Place battery pack

and wires in compartment.

INSTALLA TION

3 Attach the belt clip to the cordless handset (optional).

4 Set the dial mode.

The dial mode switch on the bottom of the base comes set to TONE. If you have touch tone service,the phone will be ready to use when installation is complete. If you have dial pulse (rotary) service, set the switch to PULSE.

5 Select base ringer volume for each line.

Set the RINGER switches on the back of the base to HIGH,LOW,or OFF.

To attach To remove

INSTALLA TION

Table/Desk Installation

1 Connect the telephone line cord(s).

If you have a two-line jack, use only the line

cord with the black plugs. Plug one end into the jack labeled L1/L2 on the base,then plug the other end into the wall jack. Make sure the cord snaps firmly into place.

If you have two separate jacks, use

both line cords. Plug one end of the line cord with black plugs into the jack labeled L1/L2 on the back of the base,then plug the other end into the wall jack for Line 1. Plug one end of the other line cord into the jack labeled L2 on the back of the base,then plug the other end into the wall jack for Line 2. Make sure the cords snap firmly into place.

2 Connect the power cord.

Use only the power cord supplied with this product. If you need a replacement,call 1 800 222-3111.

3 Charge the handset battery.

Place the handset in the base. Charge the battery for at least 16 hours the first time. After the first charge,the battery is typically fully charged overnight.

4 Check for dial tone.

After the batteries are charged,pick up the handset,press L, and

listen for a dial tone. Then press l. If you don’t hear a dial tone,see “IN CASE OF DIFFICULTY.”

NOTE: If you want to connect another device (such as a modem or fax machine) to the wall jack, you can use the jack on the phone labeled DATAPORT. This convenience port uses Line 2;a call picked up on Line 2 at this or another extension may interrupt a fax, modem, or message transmission.

Wall Installation

1 Position the wall mount adapter on the base.

INSTALLATION

Align tabs on wall mount adapter with holes on bottom of base. Snap wall mount adapter firmly into place.

+ 16 hidden pages