2N NetStar Hardware manual User Manual

2N® NetStar

Communication System

Hardware Manual

Version

3.1.0

www.2n.cz

The 2N TELEKOMUNIKACE joint-stock company is a Czech manufacturer and supplier of telecommunications equipment.

The product family developed by 2N TELEKOMUNIKACE a.s. includes GSM gateways, private branch exchanges (PBX), and door and lift communicators. 2N TELEKOMUNIKACE a.s. has been ranked among the Czech top companies for years and represented a symbol of stability and prosperity on the telecommunications market for almost two decades. At present, we export our products into over 120 countries worldwide and have exclusive distributors on all continents.

2N® is a registered trademark of 2N TELEKOMUNIKACE a.s.. Any product and/or other names mentioned herein are registered trademarks and/or trademarks or brands protected by law.

2N TELEKOMUNIKACE administers the FAQ database to help you quickly find information and to answer your questions about 2N products and services. On www.faq.2n.cz you can find information regarding products adjustment and instructions for optimum use and procedures „What to do if...“.

Declaration of Conformity

2N TELEKOMUNIKACE hereby declares that the 2N® NetStar product complies with all basic requirements and other relevant provisions of the 1999/5/EC directive. For the full wording of the Declaration of Conformity see the CD-ROM enclosed and at www.2n.cz.

The 2N TELEKOMUNIKACE company is the holder of the ISO 9001:2009 certificate. All development, production and distribution processes of the company are managed by this standard and guarantee a high quality, technical level and professional aspect of all our

Content

1. System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1	Select of the Installation part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	6
1.2	Unwrapping and Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	7
1.3	Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	8
2. Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .		11
2.1	Basic Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	12
2.2	Extension Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	15
2.3	Position and Port Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	16
2.4 CPU Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .		17
2.5	CPU Card - Extension module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	20
2.6 SWITCH card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .		21
2.7	PRI Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	25
2.8	BRI Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	28
2.9	DVL Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	31
2.10 DIGITAL COMBO Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .		33
2.11 4ASL/4AVL Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .		35
2.12 AVL Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .		37
2.13 GSM Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .		39
2.14 UMTS card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .		40
2.15 Audio Card_IO_Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .		41
2.16 IP Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .		44
3. Power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .		45
3.1	Power Supply Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	46
3.2	System Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	47
3.3	Power supply backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	49
4. Technical specifications II . . . . . . . . . . . . . . . . . . . . . . . . . . .		53

1. System Installation

Here is what you can find in this section:

1.1 Select of the Installation part

1.2 Unwrapping and Control 1.3 Installation

Selection of the Installation Site

The following aspects shall be taken into consideration while selecting a site for the system installation:

Good accessibility:

All interfaces for the connection of the telecommunication interfaces or data network connections, as well as the switch-on, switch-off and system reset controls are placed on the front side.

Protection against humidity and extreme temperatures:

The appliance may never be placed close to heat sources (radiators) or places exposed to direct sunshine. Also places with high humidity (such as bathrooms and cellars), places with significant temperature fluctuation (next to doors, windows, air-conditioning), dusty places (workshops, etc.) or places exposed to aggressive gases (accumulator room, boiler room) as well as places with intensive vibrations and places exposed to shocks (compressor rooms, heavy industrial operations) should be avoided. The system should be installed horizontally.

Installation of infrastructure in the building:

The system was designed for installation in a 19" rack and connection to the structured wiring infrastructure with termination at a CAT 3 or CAT 5 patch panel. If the infrastructure is already ready the switchboard installation site is usually given and can not be further changes. The interface must however be adjusted for the connection via RJ 45 8/8 plugs.

GSM signal quality:

If a GSM card is a part of your system (or will become later on), it is necessary to consider that the cable leading from the GSM card to the GSM antenna is usually 3m long (max. 10m). You should ensure that within this diameter from the selected system installation site a place with good GSM signal suitable for placement of the GSM antenna is available. *)

Theft protection:

While selecting the installation site the insurance company conditions should be regarded as well.

In the areas with very poor GSM signal level or high number of GSM gates the use of internal (takes the position of a line card) or external GSM splitter is advantageous.

1.1 Select of the Installation part

The following aspects shall be taken into consideration while selecting a site for the system installation:

Good accessibility:

All interfaces for the connection of the telecommunication interfaces or data network connections, as well as the switch-on, switch-off and system reset controls are placed on the front side.

Protection against humidity and extreme temperatures:

Installation of infrastructure in the building:

GSM signal quality:

Theft protection:

While selecting the installation site the insurance company conditions should be regarded as well.

In the areas with very poor GSM signal level or high number of GSM gates the use of internal (takes the position of a line card) or external GSM splitter is advantageous.

1.2 Unwrapping and Control

If you have not already done so, please check the completeness of the delivery.

The wrapping of the basic or extension module is usually used also for the transportation of other, separately acquired system components (antennas and other small additional equipment). These can be checked by matching the items on the supply list and the ordering numbers stated on all components. Usually, the system is delivered as tailor made according to the submitted order. The installation set, electronic documentation on a CD and warranty certificate are a part of the delivery. The remaining components such as telephone units and other terminals or additional appliances are delivered separately.

1.3 Installation

Here is what you can find in this section:

System Connection

System Installation

System Connection

The system is installed into a RACK min. 400 mm deep. The height of each module is 3U - 132 mm.

The system was not designed to be equipped with an active cooling unit, however the producer recommends in order to achieve a better air ventilation in case of bigger installations (more modules above each other) to leave a gap of e.g. 1U between the separate modules. For this purpose an organizer, which at the same time will ensure a better manipulation with the wiring, can be used.

For a shelf installation the system is equipped with 4 stands that create a gap between the shelf and the module body to ensure sufficient system ventilation.

System Installation

The same applies for the connection to the 230 V or 115 V power supply Network, which is subject to the local and national regulations and directives.

The connection of the system to the telecommunication network is subject to local national regulations and directives. The interface of the line cards terminates in a RJ45 plug.

Only appliances complying with the basic requirements and further specifications of the directive no. 1999/5/ES (Government Directive No. 426/200 Coll., which stipulates the technical requirements of radio and telecommunication terminal appliances, in the wording of the later regulations) may be connected to the internal analogue interface.

The supplied wiring including an additional connection to the single ground point is used for connection. If you do not use the additional system grounding, the over voltage protection integrated in the line cards will not work.

The 2N® Netstar communication system was designed as digital appliance (TDM circle switching) with sufficiently powerful processor and LAN connection with integrated VoIP telephony.

2. Technical specifications

Here is what you can find in this section:

2.1 Basic Module

2.2 Extension Module

2.3 Position and Port Numbering

2.4 CPU Card

2.5 CPU Card - Extension module

2.6 SWITCH card

2.7 PRI Card

2.8 BRI Card

2.9 DVL Card

2.10 DIGITAL COMBO Card

2.11 4ASL/4AVL Card

2.12 AVL Card

2.13 GSM Card

2.14 UMTS card

2.15 Audio Card_IO_Relay 2.16 IP Card

2.1 Basic Module

Here is what you can find in this section:

Basic Module

Basic Module Pro

Basic Module

The Basic Module Lite represents a business alternative of the basic module equipped with an CPU card, Switch X card that does not enable the connection of extension modules and one AVL card.

Ord. no. 101034 2N NETSTAR BASIC rack basic module 8x AVL

Ord. no. 101014 2N NETSTAR BASIC module 8x ASL

Basic Module Pro

Basic Module Profi is a business alternative of the basic module equipped with a CPU card, Switch card that enables the connection of up to 4 extension modules.

Ord. no. 101031 2N NETSTAR PRO rack basic module (empty)

Ord. no. 101011 2N NETSTAR PRO basic module (empty)

2.2 Extension Module

The extension module is equipped with an 8-bit CPU, which controls up to 11 analogue line cards. The following cards are supported: AVL, ASL, GSM and AUDIORELE.

Ord. no. 101036 2N NETSTAR PRO rack extender analogue only

Ord. no. 101016 2N NETSTAR PRO extender analogue only

2.3 Position and Port Numbering

Each card and port is assigned a specific unique HW address.

The address consists of 4 parts and is stated in the form: R : C : B : P, whereas the separate letters stand for the following:

R – rack

Rack represents the entire system appliance consisting of the basic module and four extension modules (case), in the current version only one Rack is supported. The rack address is thus 0.

C – case

Covers the basic or one of the four extension modules.

The address of the basic module is 1, the extension modules are assigned addresses from 2 to 5 according to their SWITCH card Connections.

B – board

The separate cards (board) are assigned addresses from left to the right, both in the basic as well as the extension modules. The address of the first position in the module is 1 and is reserved for maincase CPU or for extender CPU.

Compared to the extension module, in which the cards are assigned addresses from 1 to 12, the assigning of addresses in the basic module is governed by predefined rules.

The basic module uses following rules for the card positions and assigning of addresses.

Address 1

Reserved for controlling CPU only (position 1)

the card address is 0:1:1

Addresses 2,3,4

Reserved for the PRI and VoIP cards (positions 2,3 and 4)

the cards addresses are 0:1:2, 0:1:3 and 0:1:4

Address 5

Reserved for the SWITCH card (position 5)

the card address is 0:1:5

Addresses 6,7,8,9,10,11,12,13 and 14

The addresses correspond to the positions 6,7,8,9,10,11,12,13 and 14 and can be used for any line card. An exception are the positions with the addresses 6, 9 and 12, in which if you use a BRI or DIGITAL COMBO card the first 2 ports on the card are always NT and may not be changed.