Horizon Fitness DIGITAL SERIES DT650 User Manual

Size:
2.23 Mb
Download

DIGITAL SERIES

FOR MODELS :

DT650

DT850

TREADMILL USER’S GUIDE

I N T R O D U C T I O N

CONGRATULATIONS and THANK YOU for your purchase of this Digital Series treadmill!

Whether your goal is to win races or simply enjoy a fuller, healthier lifestyle, a Digital Series treadmill can help you attain it – adding club-qualityperformance to yourat-homeworkouts, with the ergonomics and innovative features you need to get stronger and healthier, faster. Because we're committed to designing fitness equipment from the inside out, we use only the highest quality components. It's a commitment we back with one of the strongestframe-to-motorwarranty packages in the industry.

You want exercise equipment that offers the most comfort, the best reliability and the highest quality in its class.

The Horizon Digital Series delivers.

TABLE OF CONTENTS

Important Precautions

3

 

 

Assembly

5

 

 

Before You Begin

11

 

 

Treadmill Operation

14

 

 

Conditioning Guidelines

20

 

 

Troubleshooting & Maintenance

26

 

 

Limited Warranty

29

CONTACT INFORMATION

Back Panel

IMPORTANT PRECAUTIONS INTRODUCTION

ASSEMBLY

BEFORE YOU BEGIN

TREADMILL OPERATION

TROUBLESHOOTING CONDITIONING & MAINTENANCE GUIDELINES

2

LIMITED WARRANTY

IMPORTANT INTRODUCTIONPRECAUTIONS

ASSEMBLY

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

Read all instructions before using this treadmill. When using an electrical product, basic precautions should always be followed, including the following: Read all instructions before using this treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions. If you have any questions after reading this manual, contact Customer Tech Support at the number listed on the back panel of this manual.

 

 

Connect this exercise product to a properly grounded outlet only. See grounding

 

WARNING

 

instructions.

 

 

 

 

 

 

BEFORE BEGIN YOU

TREADMILL OPERATION

LIMITED TROUBLESHOOTING CONDITIONING WARRANTY MAINTENANCE & GUIDELINES

3

GROUNDING INSTRUCTIONS

This product must be grounded. If a treadmill should malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-groundingconductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with local codes and ordinances.

Improper connection of the equipment-groundingconductor can result in a risk of

WARNING electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided

with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This product is for use on a nominal 120-voltcircuit, and has a grounding plug that looks like the plug illustrated below. A temporary adapter such as the one illustrated below may be used to connect this plug to a2-polereceptacle as shown, if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The green colored rigid ear, lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw.

3-PoleGrounded Outlet

2-PoleOutlet in Grounded Box

 

ADAPTER

 

GROUNDED

GROUNDED

TREADMILL

POWER CORD

TREADMILL

 

POWER CORD

 

 

METAL GROUNDING SCREW

WARNING To reduce the risk of burns, fire, electrical shock or injury to persons:

Never use the treadmill before securing the safety tether clip to your clothing.

If you experience chest pains, nausea, dizziness, or shortness of breath, stop exercising immediately and consult your physician before continuing.

Do not wear clothes that might catch on any part of the treadmill.

Always wear athletic shoes while using this equipment.

Do not jump on the treadmill.

Keep power cord away from heated surfaces.

Do not insert or drop any object into any opening.

Unplug treadmill before moving or cleaning it. To clean, wipe surfaces down with soap and slightly damp cloth only; never use solvents. (See MAINTENANCE)

At no time should more than one person be on treadmill while in operation.

The treadmills should not be used by persons weighing more than 275 pounds (DT650) and 300 pounds (DT850). Failure to comply will void the warranty.

The treadmills are intended for in-homeuse only. Do not use this treadmill in any commercial, rental, school or institutional setting. Failure to comply will void the warranty.

Do not use treadmill in any location that is not temperature controlled, such as garages, porches, pool rooms, bathrooms, car ports or outdoors. Failure to comply may void the warranty.

Use the treadmill only as described in this manual.

At NO time should pets or children under the age of 12 be closer to the treadmill than 10 feet. At NO time should children under the age of 12 use the treadmill.

Children over the age of 12 should not use the treadmill without adult supervision.

other safety tips for your treadmill

OPERATION

WARNING To reduce the risk of damaging important components on your treadmill, it is stronglyrecommended that your treadmill is plugged into a dedicated 20 amp outlet, without the use of an additional extension cord and/or power strip.

IMPORTANT: The treadmill is not compatible withGFCI-equippedoutlets.

It is essential that your treadmill is used only indoors, in a climate controlled room. If your treadmill has been exposed to colder temperatures or high moisture climates, it is strongly recommended that the treadmill is warmed up to room temperature before first time use. Failure to do so may cause premature electronic failure.

4

IMPORTANT PRECAUTIONS INTRODUCTION

ASSEMBLY

BEFORE YOU BEGIN

TREADMILL OPERATION

LIMITED TROUBLESHOOTING CONDITIONING WARRANTY & MAINTENANCE GUIDELINES

IMPORTANT INTRODUCTION PRECAUTIONS

ASSEMBLY

BEFORE BEGIN YOU

TREADMILL OPERATION

TROUBLESHOOTING CONDITIONING MAINTENANCE & GUIDELINES

A S S E M B LY

IMPORTANT: READ THESE SAFETY INSTRUCTIONS BEFORE USE!

WARNING

During the assembly process of the treadmill there are several areas that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises. There should be no side-to-sideplay in the console masts or any forward and back play in the console assembly or handlebars. If there is any play in these areas, the treadmill has not been properly assembled. To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.

UNPACKING

Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side. Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled and in the upright folded position, with the lock latch secure. Unpack the unit where it will be used. The enclosed treadmill is equipped with high-pressureshocks and may spring open if mishandled. Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!

Before proceeding, find your treadmill’s serial number and model name located to the left of the on/off power switch and power cord and enter it in the space provided below.

enter your serial number and model name in the boxes below:

SERIAL NUMBER:

MODEL NAME:

LIMITED WARRANTY

5

*Refer to the serial number and model name when calling for service.

*Also enter this serial number on your Warranty Card.

READING RACK

WATER BOTTLE HOLDER

GRIP PULSE HANDRAILS

SUPPORT BAR

ON/OFF SWITCH

CIRCUIT BREAKER

POWER CORD

FOOT PLATE (DT850 only)

TRANSPORT WHEEL

AIR CELL CUSHION

CONSOLE

TOUCH PAD PANEL WITH BLUE BACK-LITDISPLAY

FAN

SAFETY KEY PLACEMENT

CONSOLE MAST

MOTOR COVER

FOOT LOCK LATCH

RUNNING BELT / RUNNING DECK

SIDE RAIL

ROLLER END CAP

REAR ROLLER

ADJUSTMENT BOLTS

DT850 Shown

TOOLS INCLUDED

4 mm Allen Wrench

5 mm Allen Wrench

6 mm T-Wrench

PARTS INCLUDED

1 Safety Key

1 Console Assembly (located under treadmill deck)

1 Power Cord

3 Hardware Bags

2 Support Bars (DT650 has only 1)

IMPORTANT PRECAUTIONS INTRODUCTION

ASSEMBLY

BEFORE YOU BEGIN

TREADMILL OPERATION

TROUBLESHOOTING CONDITIONING & MAINTENANCE GUIDELINES

NOTE : If you have questions or if there are any missing parts, we will guarantee complete satisfaction. Customer Tech Support contact information is located on the back panel of this manual.

6

LIMITED WARRANTY

IMPORTANT INTRODUCTION PRECAUTIONS

P R E - A S S E M B LY

DO NOT CUT STRAPS UNTIL STEP 1-E!*Disassemble box and remove the

WARNING cardboard packaging that is not beneath the treadmill. Do not attempt to lift the treadmill at this time. Remove plastic wrap from console masts.

note: It is recommended that you apply grease to the threads of each bolt as you assemble your treadmill, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt.

ASSEMBLY

BEFORE BEGIN YOU

TREADMILL OPERATION

LIMITED TROUBLESHOOTING CONDITIONING WARRANTY MAINTENANCE & GUIDELINES

A S S E M B LY STEP 1

HARDWARE BAG 1 CONTENTS :

#0-5" NN 2UZ

-&'5$0/40-& ."45

#0-5"

-&'54*%&-*/,"(&"3.

AOpen HARDWARE BAG 1.

BLift left console mast into upright position. Be sure to hold the console mast firmly, as it will not stay in the upright position on it’s own.

CMove left side linkage arm into position. Insert bolt (A) and tighten.

DRepeat on the right side.

ENow cut the banding straps and remove remaining packaging material.*

*Note: If the straps have been removed before completing step 1-Dand the linkage arms can not be aligned, refer to the troubleshooting section (page 26) in order to restore the treadmill to its proper position.

F

Lift the running deck until

 

lock latch on side of treadmill

 

is fully engaged.

 

 

G

Remove console from box

 

and place out of the way.

 

H

Lower the treadmill running

 

deck from the folded position

 

by stepping on LOCK LATCH on

7

lower right side.

 

A S S E M B LY STEP 2

HARDWARE BAG 2 CONTENTS :

#0-5#NN

2UZ

UPQ WJFX

-0$,8"4)&3 $ 2UZ

"3$ 8"4)&3 % 2UZ

BOHMF WJFX

 

$0/40-&$"#-&

-0$,

 

8"4)&3 $

"3$ 8"4)&3 %

 

#0-5#

 

"3$ 8"4)&3 %

%0 /05 "55"$)

5)*4 4*%& 6/5*- 45&1 '

* Be sure to tighten bolts after all are lined up.

AOpen HARDWARE BAG 2.

BWith running deck in lowered position, place console

on upright masts. Slide the brackets that are underneath the console into the top holes of the upright masts.

CPlace Lock Washer (C) and bolt (B) into flat side of left upright mast and lightly tighten.

DPlace Arc Washer (D) and bolt

(B) into curved side of left upright mast and lightly tighten.

EGently lift right side of the console to connect the console cable. Carefully tuck wires in mast to avoid damage. NOTE: Do not pinch console cable or grip pulse wires.

FRepeat steps C-Dabove to assemble the right side upright mast and console.

G Tighten all bolts completely.

ASSEMBLED IN STEP 2-D

IMPORTANT PRECAUTIONS INTRODUCTION

ASSEMBLY

BEFORE YOU BEGIN

TREADMILL OPERATION

TROUBLESHOOTING CONDITIONING & MAINTENANCE GUIDELINES

8

LIMITED WARRANTY

IMPORTANT INTRODUCTION PRECAUTIONS

ASSEMBLY

BEFORE BEGIN YOU

TREADMILL OPERATION

LIMITED TROUBLESHOOTING CONDITIONING WARRANTY MAINTENANCE & GUIDELINES

A S S E M B LY STEP 3

 

 

HARDWARE BAG 3 CONTENTS :

DT650

A Open Hardware Bag 3.

 

 

 

413*/( 8"4)&3 '

B Align upper SUPPORT BAR with

#0-5&

2UZ

 

holes in CONSOLE MAST.

NN

 

 

 

2UZ

'-"58"4)&3 (

C Insert 1 BOLT (E), 1 SPRING

UPQ WJFX

 

2UZ

WASHER (F) and 1 WASHER (G)

 

 

 

 

into each of the 4 holes of the

 

DT650

SUPPORT BAR.

 

 

D Tighten all 4 BOLTS (E).

 

$0/40-& ."45

 

4611035 #"3

 

 

 

'-"58"4)&3 (

 

 

413*/( 8"4)&3 '

 

 

#0-5&

 

HARDWARE BAG 3 CONTENTS :

DT850

E DT850 ONLY: Repeat for lower

 

413*/( 8"4)&3 '

SUPPORT BAR.

#0-5&

2UZ

 

 

 

NN

 

 

2UZ

'-"58"4)&3 (

 

UPQ WJFX

 

 

2UZ

 

 

DT850

 

 

$0/40-& ."45

 

4611035 #"3

'-"58"4)&3 (

 

 

 

 

413*/( 8"4)&3 '

 

 

#0-5&

 

9