Instruction Sheet |
1066 |
LIQ_MAN_ABR_1066-CT-HT-FF-FI |
July 2013 |
|
|
1066 Liquid Analytical Transmitter |
|
ESSENTIAL INSTRUCTIONS
Read this page before proceeding!
Emerson designs, manufactures, and tests its Rosemount Analytical products to meet many national and international standards. Because these instruments are sophisticated technical products, you must properly install, use, and maintain them to ensure they continue to operate within their normal specifications. The following instructions must be adhered to and integrated into your safety program when installing, using, and maintaining Rosemount Analytical products. Failure to follow the proper instructions may cause any one of the following situations to occur: Loss of life; personal injury; property damage; damage to this instrument; and warranty invalidation.
•Read all instructions prior to installing, operating, and servicing the product. If this Instruction Manual is not the correct manual, telephone 1-800-854-8257 and the requested manual will be provided. Save this Instruction Manual for future reference.
•If you do not understand any of the instructions, contact your Emerson representative for clarification.
•Follow all warnings, cautions, and instructions marked on and supplied with the product.
•Inform and educate your personnel in the proper installation, operation, and maintenance of the product.
•Install your equipment as specified in the Installation Instructions of the appropriate Instruction Manual and per applicable local and national codes. Connect all products to the proper electrical and pressure sources.
•To ensure proper performance, use qualified personnel to install, operate, update, program, and maintain the product.
•When replacement parts are required, ensure that qualified people use replacement parts specified by Rosemount. Unauthorized parts and procedures can affect the product’s performance and place the safe operation of your process at risk. Look alike substitutions may result in fire, electrical hazards, or improper operation.
•Ensure that all equipment doors are closed and protective covers are in place, except when maintenance is being performed by qualified persons, to prevent electrical shock and personal injury.
WARNING: EXPLOSION HAZARD
DO NOT OPEN WHILE CIRCUIT IS LIVE. ONLY CLEAN WITH DAMP CLOTH.
NOTICE
If a Model 475 Universal HART® Communicator is used with these transmitters, the software within the Model 475 may require modification. If a software modification is required, please contact your local Emerson Process Management Service Group or National Response Center at 1-800-654-7768.
1066 |
Instruction Sheet |
July 2013 |
LIQ_MAN_ABR_1066-CT-HT-FF-FI |
|
|
QUICK START GUIDE – 1066 Liquid Analytical Transmitter
1.For mechanical installation instructions, see page 8 for panel mounting and page 9 for pipe or wall mounting.
2.Wire the sensor to the main circuit board. See page 10 for wiring instructions. Refer to the sensor instruction sheet for additional details. Make loop power connections.
3.Once connections are secured and verified, apply DC loop power to the transmitter.
4.When the transmitter is powered up for the first time, Quick Start screens appear. Quick Start operating tips are as follows:
a.A highlighted field shows the position of the cursor.
b.To move the cursor left or right, use the keys to the left or right of the ENTER key. To scroll up or down or to increase or decrease the value of a digit use the keys above and below the ENTER key. Use the left or right keys to move the decimal point.
c.Press ENTER to store a setting. Press EXIT to leave without storing changes. Pressing EXIT during Quick Start returns the display to the initial start-up screen (select language).
5.Choose the desired language and press ENTER.
6.Choose measurement and press ENTER.
a.For pH or ORP, choose preamplifier location. Select Analyzer to use the integral preamplifier in the transmitter; select Sensor/J-Box if your sensor is SMART or has an integral preamplifier or if you are using a remote preamplifier located in a junction box.
5.If applicable, choose units of measurement.
6.For contacting and toroidal conductivity, choose the sensors type and enter the numeric cell constant using the keys.
7.Choose temperature units: °C or °F.
8.After the last step, the main display appears. The outputs are assigned to default values.
9.To change output settings, to scale the 4-20mA current outputs, to change measurement-related settings from the default values, and to enable pH diagnostics, press MENU. Select Program and follow the prompts. Refer to the appropriate menu.
10.To return the transmitter to the factory default settings, choose Program under the main menu, and then scroll to Reset.
11.Please call the Rosemount Analytical Customer Support Center at 1-800-854-8257 if you need further support.
2
Instruction Sheet |
1066 |
LIQ_MAN_ABR_1066-CT-HT-FF-FI |
July 2013 |
|
|
Specifications
GENERAL SPECIFICATIONS
Case: Polycarbonate. IP66 (CSA, FM), NEMA 4X (CSA)
Dimensions: Overall 155 x 155 x 131mm (6.10 x 6.10 x 5.15 in.). Cutout: 1/2 DIN 139mm x 139mm (5.45 x 5.45 in.)
Conduit openings: Six. Accepts PG13.5 or 1/2 in. conduit fittings
Display: Monochromatic graphic liquid crystal display. No backlight. 128 x 96 pixel display resolution. Active display area: 58 x 78mm (2.3 x 3.0 in.). All fields of the main instrument display can be customized to meet user requirements.
Ambient temperature and humidity: -20 to 65°C (-4 to 149°F), RH 5 to 95% (non-condensing).
Storage Temperature: -20 to 70°C (-4 to 158°F)
HART® Communications: PV, SV, TV, and 4V assignable to measurement, temperature and all live HART diagnostics.
RFI/EMI: EN-61326
Complies with the following Standards:
CSA: C22.2 No 0 – 10; C22.2 No 0.4 – 04; C22.2 No. 25-M1966: , C22.2 No. 94-M91: , C22.2 No.142-M1987: , C22.2 No. 157-M1992: , C22.2 No. 213-M1987: , C22.2 No. 60529:05. UL: 50; 508; 913; 1203. ANSI/ISA: 12.12.02-2011.
ATEX: IEC 60079-0:2011, 60079-11:2011
IECEx: IEC 60079-0: 2011 Edition: 6.0, I EC 60079-11 : 2011-06 Edition: 6.0
FM: 3600: 2011, 3610: 2010, 3611: 2004, 3810: 2005, IEC 60529:2004, ANSI/ISA 60079-0: 2009, ANSI/ISA 60079-11: 2009
Hazardous Location Approvals
Intrinsic Safety (with appropriate safety barrier):
|
Class I, II, III, Div. 1 |
|
Groups A-G |
|
T4 Tamb = -20°C to 65°C |
ATEX |
1180 II 1 G |
|
Baseefa04ATEX0195X |
|
EEx ia IIC |
|
T4 Tamb = -20°C to 65°C |
IECEx BAS 11.90098X
EEx ia IIC
T4 Tamb = -20°C to 65°C
Class I, II & III, Division 1, Groups A-G T4 Tamb = -20°C to 40°C for -FI option
Tamb = -20°C to 65°C for -HT and -FF options
Class I, Zone 0, AEx ia IIC T4
Tamb = -20°C to 40°C for -FI option
Tamb = -20°C to 65°C for -HT and -FF options
Non-Incendive:
Class I, Div. 2, Groups A-D Dust Ignition Proof
Class II & III, Div. 1, Groups E-G NEMA 4/4X, IP66 Enclosure T4 Tamb = -20°C to 65°C
Class I, Division 2 Groups A-D Dust Ignition proof
Class II & III, Division 1, Groups E-G IP66 enclosure
Tamb = -20°C to 40°C for -FI option
Tamb = -20°C to 65°C for -HT and –FF options
3
1066 |
Instruction Sheet |
July 2013 |
LIQ_MAN_ABR_1066-CT-HT-FF-FI |
|
|
Input: One isolated sensor input. Measurement choices of pH/ORP, resistivity/conductivity/TDS, % concentration, total and free chlorine, monochloramine, dissolved oxygen, dissolved ozone, and temperature. For contacting conductivity measurements, temperature element can be a PT1000 RTD or a PT100 RTD. Other measurements (except ORP) and use PT100 or PT1000 RTDs or a 22k NTC (D.O. only).
Power & Load Requirements: Supply voltage at the transmitter terminals should be at least 12.7Vdc. Power supply voltage should cover the voltage drop on the cable plus the external load resistor required for HART communications (250 Ω minimum). Minimum power supply voltage is 12.7Vdc. Maximum power supply voltage is 42.4
Vdc (30 Vdc for intrinsically safe operation). The graph shows the supply voltage required to maintain 12 Vdc (upper line) and 30 Vdc (lower line) at the transmitter terminals when the current is 22 mA.
Analog Outputs: Two-wire loop powered (Output 1 only). Two 4-20 mA electrically isolated current outputs (Output 2 must be externally powered). Superimposed HART digital signal on Output 1. Fully scalable over the operating range of the sensor.
Weight/Shipping Weight: 2 lbs/3 lbs (1 kg/1.5 kg)
|
1500 |
|
|
|
|
|
|
|
|
|
|
|
1364 |
|
1250 |
|
|
|
|
ohms |
|
|
|
|
|
|
|
ohms |
1000 |
|
|
|
|
|
750 |
|
|
|
|
|
|
Load, |
|
|
|
|
|
|
|
|
|
with HART |
545 |
||
|
500 |
|
|
communication |
ohms |
|
|
|
|
|
|||
|
250 |
|
without HART |
|
|
|
|
|
|
|
|
|
|
|
|
|
communication |
|
|
|
|
0 |
18 |
24 |
30 |
36 |
42 |
|
12 |
Power supply voltage, Vdc
HART option
FIGURE 1. Load/Power Supply Requirements |
FIGURE 2. Power Supply-Current Loop Wiring |
4
Instruction Sheet |
1066 |
LIQ_MAN_ABR_1066-CT-HT-FF-FI |
July 2013 |
|
|
Specifications CONTINUED
CONTACTING CONDUCTIVITY
Performance Specifications
Measurement Range: see table below
Input filter: time constant 1 - 999 sec, default 2 sec.
Response time: 3 seconds to 95% of final reading using the default input filter
Recommended Sensors for Conductivity
All Rosemount Analytical ENDURANCE Model 400 series conductivity sensors (Pt 1000 RTD) and Model 410VP 4- electrode sensor.
PERFORMANCE SPECIFICATIONS
Recommended Range – Contacting Conductivity
|
Cell |
0.01S/cm |
0.1μS/cm |
1.0μS/cm |
10μS/cm 100μS/cm |
|
1000μS/cm 10mS/cm 100mS/cm 1000mS/cm |
||||||||||||||||||||||||||||||||||||
|
Constant |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0.01 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
200μS/cm to 2000μS/cm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
0.01μS/cm to 200μS/cm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0.1 |
|
|
|
|
|
|
|
|
0.1μS/cm to 2000μS/cm |
|
|
|
|
|
|
2000μS/cm to 20mS/cm |
|
|
|
|
|
|
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1.0 |
|
|
|
|
|
|
|
|
|
1 μS/cm to 20mS/cm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
20mS/cm to 200mS/cm |
|
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
4-electrode |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2μS/cm to |
1400mS/cm |
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Linearity for Standard Cable ≤ 50 ft (15 m) |
|
||
|
|
|
|
|
±0.6% of reading in recommended range |
|
||
|
|
|
|
|
|
|||
|
|
|
|
|
|
|||
|
|
|
|
|
±2% of reading outside high recommended range |
|
||
|
|
|
|
|
|
|||
|
|
|
|
|
|
|||
|
|
|
|
|
±5% of reading outside low recommended range |
|
||
|
|
|
|
|
±4% of reading in recommended range |
|
||
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
Temperature specifications: |
||||||||
|
|
|
|
|
|
|
|
|
Temperature range |
|
0 to 200°C |
|
|
||||
|
|
|
|
|
|
|
|
|
Temperature Accuracy, |
|
± 0.1°C |
|
|
||||
Pt-1000, 0-50°C |
|
|
|
|||||
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
Temperature Accuracy, |
|
± 0.5°C |
|
|
||||
Pt-1000, Temp. > 50°C |
|
|
|
|||||
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
5
1066 |
Instruction Sheet |
July 2013 |
LIQ_MAN_ABR_1066-CT-HT-FF-FI |
|
|
Specifications CONTINUED
TOROIDAL CONDUCTIVITY
Performance Specifications
Measurement Range: see table below
Input filter: time constant 1 - 999 sec, default 2 sec.
Response time: 3 seconds to 95% of final reading
Recommended Sensors for Conductivity
All Rosemount Analytical submersion/immersion and flow-through toroidal sensors.
PERFORMANCE SPECIFICATIONS
Recommended Range - Toroidal Conductivity
|
|
|
Model |
1μS/cm |
10μS/cm |
100μS/cm |
1000μS/cm |
10mS/cm |
100mS/cm |
|
1000mS/cm 2000mS/cm |
|||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
226 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
5μS/cm to 500mS/cm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
500mS/cm to 2000mS/cm |
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
225 & 228 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
15μS/cm to 1500mS/cm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1500mS/cm to 2000mS/cm |
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
242 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
100μS/cm to 2000mS/cm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
222 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
(1in & 2in) |
|
|
|
|
|
|
|
500μS/cm to 2000mS/cm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LOOP PERFORMANCE (Following Calibration)
Model 226: ±1% of reading ±5μS/cm in recommended range
Models 225 & 228: ±1% of reading ±15μS/cm in recommended range
Models 222, 242: ±4% of reading ±5mS/cm in recommended range
Models 225, 226 & 228: ±5% of reading outside high recommended range
Temperature specifications:
Temperature range |
-25 to 210°C (-13 to 410ºF) |
|
|
|
|
Temperature Accuracy, |
± 0.5°C |
|
Pt-100, -25 to 50 °C |
||
|
||
Temperature Accuracy, |
± 1°C |
|
Pt-100,. 50 to 210°C |
||
|
6