Zoom Wireless-N, 1095 Series, 4403 User Manual

Wireless-N 4-port Router

USER MANUAL

NOTICE

This document contains proprietary information protected by copyright, and this Manual and all the accompanying hardware, software, and documentation are copyrighted. No part of this document may be photocopied or reproduced by mechanical, electronic, or other means in any form.

The manufacturer does not warrant that the hardware will work properly in all environments and applications, and makes no warranty or representation, either expressed or implied, with respect to the quality, performance, merchantability, or fitness for a particular purpose of the software or documentation. The manufacturer reserves the right to make changes to the hardware, software, and documentation without obligation to notify any person or organization of the revision or change.

All brand and product names are the trademarks of their respective owners.

MENT

Contents

Contents .............................................................................................................................. 3

Getting Started .................................................................................................................... 5

Package Contents................................................................................................................................5

Introduction ........................................................................................................................................ 5

Using the Router Mode....................................................................................................... 6

Step 1. Setup Login Password................................................................................................8

Step 2. WAN Setup ..................................................................................................................9

Step 3. Wireless Settings........................................................................................................16

Wireless Security Settings......................................................................................................17

Step 4. Summary.....................................................................................................................19

Step 5. Finish........................................................................................................................... 20

Resetting the Router to the Factory Configuration ....................................................................21

Ethernet Client Mode ....................................................................................................... 22

Step 1. Setup Login Password.............................................................................................. 25

Step 2. WAN Type Setup ......................................................................................................25

Step 3. Ethernet Client Mode page .....................................................................................26

Step 4. Summary.....................................................................................................................27

Step 5. Completing the Installation .....................................................................................29

Setting up the Wireless-N 4-port Router as a Repeater.................................................... 30

Setting up a WDS network ...................................................................................................30

Installing the Hardware .........................................................................................................31

Setting Up the Router in Hybrid mode or WDS Only mode .........................................32

Setting up a Network ........................................................................................................ 34

To Connect Additional Wired Computers .........................................................................34

To Connect a Network Device ............................................................................................34

Connecting Wireless Devices to the Wireless-N 4-port Router........................................ 36

Establishing your Wireless Network ...................................................................................36

Connecting a Windows 7 Computer with Built-in Wireless Capabilities ......................37

Connecting a Windows Vista Computer with Built-in Wireless Capabilities ...............38

Connecting a Windows XP Computer with Built-in Wireless Capabilities ..................39

Connecting a Wireless-enabled Computer or Device (including the iPhone® or other

cellular phones, the iPod Touch®, etc.) to the Wireless-N 4-port Router....................39

Connecting a Computer with a Wireless Adapter to the Wireless-N 4-port Router...40

Using the Configuration Manager's Advanced Program ................................................. 42

Changing Default Settings ..............................................................................................................42

Online Help.......................................................................................................................................42

Launching the Configuration Manager's Advanced Program................................................... 43

Configuring Basic Settings.................................................................................................... 44

The Basic Setup Page.............................................................................................................44

The LAN Setup Page............................................................................................................. 46

The Wireless Settings Page ...................................................................................................48

The Change Password Page..................................................................................................51

Configuring Forwarding Rules .............................................................................................52

The Virtual Server Page.........................................................................................................53

The Port Triggering Page...................................................................................................... 54

The Miscellaneous Page ........................................................................................................55

Configuring Security Settings ...............................................................................................57

Packet Filters Page..................................................................................................................57

The Domain Filters Page ......................................................................................................59

The URL Blocking Page........................................................................................................60

The MAC Address Control Page.........................................................................................61

The Miscellaneous Page ........................................................................................................62

Configuring Advanced Settings............................................................................................64

The System Time Page ..........................................................................................................64

The System Log Page.............................................................................................................65

The Dynamic DNS Page....................................................................................................... 67

The QoS Rule Page................................................................................................................68

The SNMP Page.....................................................................................................................69

The Routing Table Page ........................................................................................................70

The Schedule Rule Page ........................................................................................................71

Configuring Toolbox Settings...............................................................................................74

System Information Page...................................................................................................... 74

The Firmware Upgrade/Restore Page ................................................................................ 74

The Backup Setting Dialog ...................................................................................................75

The Reset to Default Dialog................................................................................................. 75

The Reboot Dialog.................................................................................................................76

The Miscellaneous Page ........................................................................................................76

Appendix A: Troubleshooting Tips .................................................................................. 77

Appendix B: TCP/IP Network Settings ........................................................................... 80

Macintosh TCP/IP Settings .................................................................................................80

Mac OS X 10.7 (Lion), 10.6 (Snow Leopard), and 10.5 (Leopard)................................ 80

Mac OS X 10.4 and 10.3 .......................................................................................................80

Mac OS 7.6.1 - 9.2.2............................................................................................................... 80

Windows TCP/IP Settings ...................................................................................................81

Windows 7 Users:................................................................................................................... 81

Windows Vista Users:............................................................................................................81

Windows XP ...........................................................................................................................82

Windows 2000.........................................................................................................................82

Windows 98/Me..................................................................................................................... 82

Appendix C: Setting up Your Network Using WPS .......................................................... 84

Configuration Methods .........................................................................................................84

Method One............................................................................................................................84

Method Two............................................................................................................................ 84

Method Three .........................................................................................................................85

Appendix D: Registering Your Product and Getting Help............................................... 86

Appendix E: Regulatory Information............................................................................... 87

Europe – EU Declaration of Conformity ...................................................................................88

Limited Warranty.............................................................................................................................. 91

4 Wireless-N 4-port Router User Manual

Getting Started

Package Contents

The package contains the Zoom Wireless-N 4-port Router, an RJ-45 Ethernet cable, a 5V 1.0A power cube, a Quick Start flyer, and a CD that contains additional documentation and warranty information.

If anything is missing or damaged, please contact Zoom Customer Support or whoever provided the Wireless-N 4-port Router.

Introduction

The Wireless-N 4-port Router can be used in 3 different modes. Once you determine which mode you want to use, you can follow the relevant chapters of this User Manual.

• Router Mode: The device is set up to be in Router Mode by default. In the Router

Mode, the device provides wired and wireless access to clients on a network. Most users will use this mode. To use the Router Mode, go to

• As an Ethernet Client, the Router allows a device with an Ethernet port, such as a

gaming console, computer, or HDTV, to join an existing wireless network. You might use Ethernet Client mode for a device that doesn’t have wireless capability, or for a device where you need the superior wireless range of the Wireless-N 4-port Router. To use the Router as an Ethernet Client, go to

• In the Repeater Mode, the Router is used to extend the range of a wireless network.

You can use this mode if, for example, the main wireless Router is in the basement of a multi-floor home and you are unable to access it from some locations. In this instance, you can install the Wireless-N 4-port Router on another floor of the house to provide access to both wired and wireless devices throughout the house. To use the Router as

a Repeater, go to

Chapter 4.

Chapter 2.

Chapter 3.

Using the Router Mode

This chapter explains how to setup your Wireless-N 4-port Router in Router Mode. Most users will select this mode. In Router Mode the Wireless-N 4-port Router typically connects to a broadband modem such as a Cable or ADSL modem and becomes the center of a wired and/or wireless network.

Installing the Hardware

1 Place the Wireless-N 4-port Router near a computer to be used for setup. This computer needs an

Ethernet (LAN) port.

2 Turn off the computer.

ntenna

Wan por

Power Jac

3 Attach the antenna to the Router if the antenna isn’t already attached. (Remove the antenna from the

package. Place the end of the detachable antenna on the open antenna connection port and rotate the antenna clockwise by hand until it no longer turns easily. It may take many turns before the antenna is completely connected. Move the antenna into a vertical orientation. The antenna should snap into place.)

4 Connect one end of the supplied Ethernet cable to the computer’s Ethernet port and the other end to

any of the Wireless-N 4-port Router’s Ethernet (LAN) ports. Note: If you are using a Cable or ADSL modem to access the Internet, unplug that Ethernet cable

from your computer and plug it into the Router’s WAN port. Then connect one end of the supplied

Ethernet ports

Reset Button

6 Wireless-N 4-port Router User Manual

Ethernet cable to the computer’s Ethernet port and the other end to any of the Wireless-N 4-port Router’s Ethernet (LAN) ports.

5 Plug the supplied power cube into the Wireless-N 4-port Router and then into a power outlet.

Important: Use only the power cube shipped with the Wireless-N 4-port Router. Other power cubes may damage the device.

6 Turn on the computer. The connected Ethernet (LAN) port light should start blinking or stay on. If

the connected Ethernet (LAN) light doesn’t blink or turn on, please see

Appendix A:

Troubleshooting Tips.

Using the Setup Wizard

1 In the computer's Web browser address bar, type http://192.168.2.1 and then click

Enter.

2 When the USER'S MAIN MENU opens, it displays a Status page that lists the

current values for a variety of settings. If the Status page doesn’t appear, please see

Appendix A: Troubleshooting Tips.

3 In the System Password field, type admin and then click Login.

Note: Later, if you change the System Password, you will use the new password to log in.

4 Click Wizard on the Toolbar to launch the Setup Wizard, which will guide you through

the configuration process.

5 The Setup Wizard page opens.

6 Each of the five Steps guides you in configuring a specific setting or group of settings.

When you click Next or Back, you move from one step to another. If there is a setting that you don’t want to change, simply click Next to go to the next setting.

Step 1. Setup Login Password

To view or change configuration settings, you must enter a password. Your Router’s default password admin was set by the factory and you used it to access the Configuration Manager initially. To safeguard your configuration, particularly if you make changes, we recommend that you change the login password. If you want to keep the default password, click Next and continue reading at step 2 below. If you want a new password, continue with step 1 directly below.

1 On the Setup Login Password page, type the old password (initially admin) in the Old Password

field.

2 Type the new password in the New Password field. 3 Type the new password in the Reconfirm field, and then click Next.

8 Wireless-N 4-port Router User Manual

Note: If you forget the new password, you won't have access to the Configuration Manager and will need to restore the device to its factory settings (see Resetting the Router to the Factory

Configuration), thus losing any changes you made to your Router's configuration. To avoid this

problem, we recommend that you write the new password here and on the bottom of your Wireless-N 4-port Router, and that you also save it elsewhere such as a settings document.

PASSWORD:______________________________________

Step 2. WAN Setup

The WAN Type refers to the protocol used by your Internet Service Provider in establishing your Internet connection.

Selecting the WAN Type

On the WAN Type Setup page, you can either Auto Detect your WAN connection or Setup your WAN connection manually.

If you are not sure what connection type you are using, we suggest that you run Auto Detect since it only takes a couple of seconds to run and the Setup Wizard will automatically display the manual setup option page if Auto Detect fails. (The Auto Detect option only detects Dynamic IP and PPPoE.) If you Auto Detect your connection and it is successful, the Setup Wizard will display the appropriate page to set up your connection using either the Dynamic IP page (see

Configuring the Dynamic IP Address on page 11) or the PPPoE page (See Configuring PPPoE

on page display the Manually Selecting your WAN Type page as shown below.

12) If you Auto Detect your connection and it is not successful, the Setup Wizard will

Manually Selecting your WAN Type

If you selected Setup your WAN Connection Manually or the manual setup option page below appears after you run Auto Detect, select your connection from the following options:

• Dynamic IP Address: Select this if you are using a cable modem or if your ADSL

modem does not use PPPoE. Most users will select this. (ADSL service providers will typically tell you whether you are using PPPoE, which requires you to enter a PPPoE-related password into the Router. If you are using ADSL with 1483 routed, bridged, or PPPoA modes, you are not using PPPoE.)

• PPPoE: Select this if you are using an ADSL Router with PPPoE.

• Static IP Address: Typically you must request and pay extra for a static IP. In the

unlikely event that you have done this, select Static IP Address.

• L2TP: The Layer 2 Tunneling Protocol is more common in corporate environments

and most users will not use this setting. In the unlikely event that you are using a VPN to access a network that uses Layer 2 Tunneling Protocol, select this option.

• PPTP: The Point to Point Tunneling Protocol is more common in corporate

environments and most users will not use this setting. In the unlikely event that you are using a VPN that uses Point to Point Tunneling Protocol, select this option.

Note: If you read the discussion above and are still unsure which WAN Type to choose, please check with your service provider.

Click Next.

The relevant section immediately below depends on the WAN Type you selected.

10 Wireless-N 4-port Router User Manual

Configuring the Dynamic IP Address

The page shown below only appears if you select the Dynamic IP Address button on the Select WAN Type menu or Auto Detect found a connection using Dynamic IP. Otherwise skip

this section.

• Host Name (optional)

This is the name that identifies your Wireless-N 4-port Router. Some service providers require a host name. Your service provider supplies this name, if needed. Most users don’t need to enter a host name.

• Enable Mac Cloning

This is the 12-digit Media Access Control (MAC) address of your Router. Cable Modem users should click the Clone MAC button to get the MAC address that was

registered with your service provider for your device. Use the computer that was connected to your cable modem when cloning the MAC address.

Click Next to continue.

Go to

Step 3. Wireless Settings

Configuring PPPoE

The page shown below only appears if you select the PPPoE button on the Select WAN Type menu or Auto Detect found a connection that uses PPPoE. Otherwise skip this section.

• PPPoE Username

This is the PPPoE username supplied by your service provider.

• PPPoE Password

This is PPPoE password supplied by your service provider.

• Primary DNS

This is the Domain Name System (DNS) server's IP address. Your service provider supplies this address, if needed. Most users should not need to enter a DNS value.

• Secondary DNS

This is the IP address of an alternate Domain Name System (DNS) server. Your service provider supplies this address, if needed. Most users should not need to enter a secondary DNS value.

• PPPoE Service Name

This is the name assigned by your service provider to identify your service. The Service Name is optional. Most users will not enter a Service Name.

• Assigned IP Address

This is the optional IP address assigned by your service provider. Most users will not need to enter an Assigned IP Address.

Click Next to continue.

Go to

Step 3. Wireless Settings.

12 Wireless-N 4-port Router User Manual

Configuring the Static IP Address

The page shown below will only appear in the unlikely event that you select the Static IP Address button on the Select WAN Type menu. Otherwise skip this section.

• Static IP Address

This is the IP address that is given to you by your service provider when you sign up for a Static IP address. This address identifies your Wireless-N 4-port Router when seen from the Internet.

• Subnet Mask

This is the Router's subnet mask. Your service provider supplies this address.

• Default Gateway

This is the IP address of the ISP server. Your service provider supplies this address.

• Primary DNS

This is the Domain Name System (DNS) server's IP address. Your service provider supplies this address.

• Secondary DNS

This is the IP address of an alternate Domain Name System (DNS) server. Your service provider supplies this address.

Click Next to continue.

Go to Step 3. Wireless Settings.

Configuring PPTP

The page shown below only appears if you select the PPTP button on the Select WAN Type menu. Otherwise skip this section.

• IP Mode

This is the mode used to generate the IP address. Select an option from the dropdown menu, based on your service provider's requirements.

• My IP Address

This is the private IP address that your service provider assigned to your Router.

• My Subnet Mask

This is the private subnet mask that your service provider assigned to your Router.

• Gateway IP

This is the IP address of the service provider's server. Your service provider supplies this address.

• Server IP Address/Name

This is the name and IP address of the PPTP server. Your service provider supplies this information, if needed.

• PPTP Username

This is the PPTP username that your service provider assigned to you.

• PPTP Password

This is PPTP password that your service provider assigned to you.

Click Next to continue.

Step 3. Wireless Settings.

Go to

14 Wireless-N 4-port Router User Manual

Configuring L2TP

The page shown below only appears if you select the L2TP button on the Select WAN Type menu. Otherwise skip this section.

• IP Mode

This is the mode used to generate the IP address. Select an option from the dropdown menu, based on your service provider's requirements.

• IP Address

This is the IP address that identifies the L2TP server. Your service provider supplies this address.

• Subnet Mask

This is the Router's subnet mask. Your service provider supplies this address.

• WAN Gateway IP

This is the WAN Gateway IP address of the L2TP server. Your service provider supplies this address.

• Server IP Address/Name

This is the name and IP address of the L2TP server. Your service provider supplies this information, if needed.

• L2TP Username

This is the L2TP username or user name supplied by your service provider.

• L2TP Password

This is L2TP password supplied by your service provider.

Click Next to continue.

Go to

Step 3. Wireless Settings.

Step 3. Wireless Settings

The Wireless Settings page lets you change the wireless settings for your Wireless-N 4-port Router. After running the Setup Wizard you will need to make sure that wireless devices connecting to the Wireless-N 4-port Router (computers, phones, tablets, game stations, etc.) are set up properly, compatible with your Router’s wireless settings. For instructions, refer to

Wireless-N 4-port Router.

If you are happy with your wireless settings (set at the factory to wireless without security), click

Next. Otherwise, continue below.

Chapter 6, Connecting Wireless Devices to the

Wireless Accept the default Enable. Click the Disable radio button only if you do

•

not want wireless clients to access your network.

•

SSID (Wireless Network Name) is the name that you want to give your wireless network. By default, the SSID for the Wireless-N 4-port Router is

Zoom. You can change the SSID to a name of your choice. The SSID can be up to 32 alphanumeric characters. If you change the name, make sure that all devices on your Wireless-N 4-port Router’s wireless network use the new SSID as the access point.

Channel refers to the wireless network channel assigned to your LAN. By default, the

•

Wireless-N 4-port Router uses channel 10. You would only change this setting if you were concerned about possible interference from another wireless access point using the same channel.

Note: Other wireless networks might be within range of your network. Your neighbors, for instance, may be within range. If you are having trouble connecting, try setting a different channel to see if that improves performance. You should try setting a channel that is at least a 5 channel difference than what you are using. By default, the Wireless-N 4-port Router is set to 10. You may want to try channel 4 or 5, for instance, if you have trouble connecting with the default channel (10).

Click Next to continue.

16 Wireless-N 4-port Router User Manual

Wireless Security Settings

If you accepted the default to Enable the Wireless Module (on the Wireless Settings page at Step 3), the following page opens when you click Next.

From the drop-down menu, you can choose either none, WEP, or WPA2/WPA. By default, the Router does not have security enabled. However, we strongly recommend that you configure wireless security for your network. You need to use the same security mode you select for your wireless Router for each wireless device using the Router. If a Pass Phrase or WEP key is used, it needs to be the same for all devices including the Router.

Select from the following options:

o WPA2/WPA (Recommended): Most users should select the

WPA2/WPA option. When you select this option, the Security Key field appears.

• Security Key: Please input 8 to 63 characters as your Security

key.

Field Entry Security Key In the Security Key field, enter a value for the

key between 8 and 63 characters. Write your key in the space below for future

reference, and then enter it in the Security Key field:

— — — — — — — — — — — — — — — — — — — —

o WEP: You must select this option in the unlikely event that you have

devices on your network that only support WEP. Otherwise we recommend WPA2/WPA. (Devices that only support WEP include older handheld game consoles, older MAC notebooks, and very old Windows notebooks. If you need to use WEP, enter the correct encryption key.)

Field Entry

Click Next

Encryption WEP Key 1, 2, 3, 4

You can choose to either use WEP 128 bit encryption or WEP 64 bit encryption. The difference is 128 bit is more secure and 64 bit is faster. We recommend selecting 64 bit.

If you chose a 64-bit key length, 10 Hexadecimal characters are required. Hexadecimal characters are the numbers 0-9 and the characters A-F. Write the 10 Hexadecimal character key in the space below for future reference, and then enter it in the Key 1 box.

— — — — — If you chose a 128-bit key length, 26 Hexadecimal

characters are required. Hexadecimal characters are the numbers 0-9 and the characters A-F. Write the 26 Hexadecimal character key in the space below for future reference, and then enter it in the Key 1 box.

— — — — — — — — — — — — —

o None (the default): Select this if you don’t plan to use wireless security or

if all the devices on your network support WPS (WiFi

Protected

Setup) and you wish to use WPS to set up wireless security. We

recommend using the Setup Wizard with the options above to set up security for your Wireless-N 4-port Router. However, if you choose to use WPS, please refer to

Appendix C: Setting up Your Network Using

WPS.

18 Wireless-N 4-port Router User Manual

Step 4. Summary

The Summary page displays the updated configuration settings for your Router and lets you accept, change, and test the configured values.

1 To edit your entries, click Back as many times as needed to access the page for the

field(s) to be edited, then click Next to continue with your edits or to return to the updated Summary page.

2 The Wireless-N 4-port Router is set by default to test your network connection. If you

do not wish to test your connection, please uncheck the Do you want to proceed with the network testing? checkbox.

3 When you're satisfied with the configured settings, click Confirm to save the new

configuration.

Step 5. Finish

The Finish page displays the saved configuration settings for your Router.

Click Finish to exit the Setup Wizard and return to the Main Menu.

Important! If you see the message “Connection to Internet Failed!” try the following:

• Check that the Ethernet cables are all securely connected.

• Check that you have installed an Ethernet cable from the Router’s WAN port to the

Ethernet port of your Cable or ADSL modem.

• Power off your computer, the Router and your modem, and then turn on modem and

allow it to connect. Next turn on the Router, wait until the Router is completely powered up and the WLAN light is blinking, then turn on your computer. Try running the setup wizard again.

• Click the Reconfigure button and go through the configuration again. This time uncheck

the Do you want to proceed with the Network Testing? button. After you Apply the settings, try opening your browser and going to your favorite web page. If this doesn’t work contact Zoom Technical Support. See

Appendix D, Registering your Product and Getting

Help.

Congratulations! Your Wireless-N 4-port Router is now setup. If you need help connecting additional computers or devices to your Wireless-N 4-port Router please refer to:

Chapter 5, Setting up a Network for help on adding other computers or network

devices through the Wireless-N 4-port Router’s Ethernet ports.

Chapter 6, Connecting Wireless Devices to the Wireless-N 4-port Router for help on

connecting wireless computers, phones, tablets and game stations.

In the unlikely event you need to make changes to the Wireless-N 4-port Router’s advanced settings please see

Chapter 7, Using the Configuration Manager’s Advanced Program.

20 Wireless-N 4-port Router User Manual

Resetting the Router to the Factory Configuration

In the unlikely event that you need to reset the Router to the factory default configuration, insert the blunt end of a paper clip into the RESET hole on the back panel of the Router. Hold the clip in place for five (5) seconds.

Ethernet Client Mode

This chapter explains how to setup your Wireless-N 4-port Router as an Ethernet Client. Ethernet Client Mode allows a game station, computer, HDTV, or other device with an Ethernet port to use the Router to connect to a wireless network.

Configuring the Router by Using a Computer

1 Place the Wireless-N 4-port Router near a computer to be used for setup. This computer needs an

Ethernet (LAN) port. This computer will be used to set up the Wireless-N 4-port Router. After the setup is complete, the Router can be connected to the device that needs wireless capability.

2 Turn off the computer.

3 Attach the antenna to the Router if the antenna isn’t already attached. (Remove the antenna from the

4 Connect one end of the supplied Ethernet cable to the computer’s Ethernet port and the other end to

any of the Wireless-N 4-port Router’s Ethernet (LAN) ports.

5 Plug the supplied power cube into the Wireless-N 4-port Router, and then into a power outlet.

22 Wireless-N 4-port Router User Manual

Important: Use only the power cube shipped with the Wireless-N 4-port Router. Other power cubes may damage the device.

6 Turn on the computer. The connected Ethernet (LAN) port light should start blinking. If the

connected Ethernet (LAN) light doesn’t blink, please see

Appendix A: Troubleshooting Tips.

Using the Setup Wizard

To launch the Configuration Manager, please follow these steps:

1 In the computer's Web browser address bar, type http://192.168.2.1 and then click

Enter.

2 When the USER'S MAIN MENU opens, it displays a Status page that lists the

current values for a variety of settings. If the Status page doesn’t appear, please see

Appendix A: Troubleshooting Tips.

3 In the System Password field, type admin and then click Login.

Note: Later, if you change the System Password, you will use the new password to log

in.

4 Click Wizard on the Toolbar to launch the Setup Wizard, which will guide you through

the configuration process.

5 The Setup Wizard page opens.

6 Each of the Steps guides you in configuring a specific setting or group of settings.

When you click Next or Back, you move from one step to another. If there is a setting that you don’t want to change, simply click Next to go to the next setting.

24 Wireless-N 4-port Router User Manual

Step 1. Setup Login Password

1 On the Setup Login Password page, type the old password (initially admin) in the Old Password

field.

2 Type the new password in the New Password field. 3 Type the new password in the Reconfirm field, then click Next.

Note: If you forget the new password, you won't have access to the Configuration Manager and will need to restore the device to its factory settings (see Resetting the Router to the Factory

Configuration), thus losing any changes you made to your Router's configuration. To avoid this

problem, we recommend that you write the new password here and on the bottom of your Wireless-N 4-port Router, and that you also save it elsewhere such as a settings document.

PASSWORD:______________________________________

Step 2. WAN Type Setup

On the WAN Type Setup page, select Setup Ethernet Client Mode. Then click Next.

Chapter 3: Connecting an Ethernet Client 25

Step 3. Ethernet Client Mode page

1 Select the Enabled button to enable Ethernet Client Mode. 2 Select the radio button corresponding to the name of the wireless network (the SSID) you

want to join.

3 If the wireless network you selected has security enabled, enter the Security Key used by

your wireless network.

4 Click Next.

26 Wireless-N 4-port Router User Manual

Step 4. Summary

Click Confirm.

Next click Finish to go to the Status page.



Chapter 3: Connecting an Ethernet Client 27

You should now see the Ethernet Client Mode status. If it displays Connected your setup is complete. Congratulations!

(You may need to click the Refresh button to update the page if it does not say Connected.)

28 Wireless-N 4-port Router User Manual

+ 63 hidden pages