AK08xxAS Adjustable Depth Liners
WARNING:
When building a custom hood for a power pack, always follow all applicable construction codes and standards.
See the illustrations and table below to locate your liner choice and use corresponding custom hood base dimensions. For the liner installation, only the bottom of the custom hood is needed. Do not finalize the entire custom hood yet, because an opening is needed for the power pack.
Recommended |
|
thickness: |
|
3/4'' |
B |
A
Plywood base thickness: 3/4”
|
|
Liner |
|
Power Pack |
|
Custom Hood |
*Inside |
*Inside Depth (B) |
|||
|
|
Model |
|
Model |
|
Exterior Width |
Width (A) |
|
|
||
|
|
Without Backboard |
**With Backboard |
||||||||
|
|
|
|
|
|
|
|
|
|
||
|
|
AK0800AS |
|
|
AK8000AS |
|
30 inches |
|
28 1/2” |
17 1/2” - 20 1/2” |
17 1/8” - 20 1/8” |
|
|
|
|
||||||||
|
|
|
|
|
and |
|
|
|
|
||
|
|
AK0836AS |
|
|
|
36 inches |
|
34 1/2” |
|
|
|
|
|
|
|
AK8100AS |
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AK0806AS |
|
|
AK8200AS |
|
36 inches |
|
34 1/2” |
20 1/2” - 23 1/2” |
20 1/8” - 23 1/8” |
|
|
AK0842AS |
|
|
|
42 inches |
|
40 1/2” |
|||
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AK0848AS |
|
|
|
|
48 inches |
|
46 1/2” |
|
|
|
|
AK0854AS |
|
|
AK8300ASX |
|
54 inches |
|
52 1/2” |
20 1/2” - 23 1/2” |
20 1/8” - 23 1/8” |
|
|
AK0860AS |
|
|
|
|
60 inches |
|
58 1/2” |
|
|
|
|
AK0840AS |
|
|
AK8400AS |
|
30 inches |
|
28 1/2” |
17 1/2” - 20 1/2” |
17 1/8” - 20 1/8” |
|
|
AK0846AS |
|
|
|
36 inches |
|
34 1/2” |
|||
|
|
|
|
|
|
|
|
|
|||
|
|
AK0886AS |
|
|
|
|
36 inches |
|
34 1/2” |
|
|
|
|
AK0882AS |
|
|
AK8800AG |
|
42 inches |
|
40 1/2” |
|
|
|
|
AK0888AS |
|
|
|
48 inches |
|
46 1/2” |
20 1/2” - 23 1/2” |
20 1/8” - 23 1/8” |
|
|
|
|
|
and |
|
|
|||||
|
|
|
|
|
AK8800AS |
|
|
|
|
|
|
|
|
AK0884AS |
|
|
54 inches |
|
52 1/2” |
|
|
||
|
|
AK0880AS |
|
|
|
|
60 inches |
|
58 1/2” |
|
|
Installation -
*Dimension does not include 3/8” wide flange around liner.
**The inside depth shown in the table above assumes a minimum cabinet backboard thickness of 3/8”.
FIG 1: Zephyr recommends the base of the custom hood to be 3/4” thick plywood. The sides, front and backboard (if included) of the custom hood to be 3/4” thick, assuming standard cabinet widths.
Consider the shape and size of the power pack to determine the configuration of the custom hood. For more details, refer to the installation manual of the power pack.
Zephyr Corporation
2277 Harbor Bay Pkwy, Alameda, CA 94502
Tel: 1.888.880.8368 Fax: 1.888.990.8368 e-mail: productsupport@zephyronline.com
FEB15.0301 |
1 |
www.zephyronline.com |