Page 1
User’s Manual
CNPS9700 NT
www.ZALMAN.com
V 2.2
Intel Socket 1155/1156/775 CPU
Core i7
Core i5
Core i3
Core 2 Quad
Core 2 Duo
Pentium Dual Core
Pentium D
Pentium 4
Celeron D
AMD Socket AM3/AM2+/AM2/754/939/940 CPU
Phenom II
Phenom
Athlon II
Athlon X2
Athlon FX
Athlon
Opteron
Dual-Core Opteron
Sempron
To ensure safe and easy installation,
please read the following precautions.
Page 2
1
.COM
2. Specifications
Model
Spec.
CNPS9700 NT
Material Pure Copper and Aluminum
Weight 764g
Dimensions 90(L) Ⅹ 124(W) Ⅹ 142(H)㎜
Fan
Bearing-Type 2 Ball-Bearing
RPM 1,250rpm ± 30% ~ 2,800rpm ± 10%
Noise Level 19.5 ~ 35dBA ± 10%
Key Functions PWM Control, Auto Restart
ZM-STG1
Net Weight 3.5g
Temp Range -40 ~ 150℃ (-40 ~ 302℉)
1. Precautions
1) Use and keep product away from reach of children and pets.
2) Do not ingest the Thermal Grease, and avoid its contact with skin and
eyes. If contact is made with skin, wash off with water. If ingested or
irritation persists, seek medical attention.
3) To prevent possible injuries, gloves must be worn while handling this
product.
4) Excessive force exerted on the fan may cause damage to the fan and/
or system.
5) Avoid inserting objects or hands into the fan while it is in operation to
prevent product damage and injuries.
6) Check the components list and condition of the product before
installation. If any problem is found, contact the retailer to obtain a
replacement.
7) Zalman Tech Co., Ltd. is not responsible for any damages due to
overclocking.
8) During transportation of the system, the cooler must be removed.
Zalman is not responsible for any damages that occur during the
transport of a system.
9) Product design and specifications may be revised to improve quality
and performance.
Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages due
to external causes, including but not limited to, improper use,
problems with electrical power, accident, neglect, alteration,
repair, improper installation, or improper testing.
Page 3
2
.COM
1) Common Components
3. Components
Clip Support Fixing Bolts
AMD Clip LeverAMD Clip
Clip Support
User’s Manual
Washers
Nuts
Intel Clip
Clip Fixing Bolts
Cooler
2) Intel Components
3) AMD Components
Thermal Grease
[ZM-STG1]
Page 4
3
.COM
4. Installation Requirements
1) Space Requirements
2) Air Guide Removal
3) Cooler Orientation
The cooler’s installation requires unobstructed space with dimensions of 127㎜
(width), 93㎜(length), 145㎜(height), and the CPU as a central reference point.
Please check if components such as ODDs and PSU protrude into the required
space.
Air guides on enclosures must be removed, before the cooler’s installation, for
they protrude into the cooler’s required space.
It is recommended that the cooler be installed so that air flows from the cooler toward
the enclosure’s rear exhaust fan.
93㎜
145㎜
127㎜
PSU
Page 5
4
.COM
4) Installation Based On Clip Orientation
A. Horizontal Clip Orientation
B. Vertical Clip Orientation
Page 6
5
.COM
② Remove any foreign particles from the Base of the the cooler and the
surface of the CPU, then shake well the enclosed thermal grease and
apply a through layer of thermal grease on the surface of the CPU and
the Base of the cooler.
1) Intel Socket 1155 / 1156 / 775 Installation
① Install the Clip Support to the motherboard according to the socket-type.
5. Installation
Nut
Washer
Bolt(silver)
Clip Support
M/B
Socket 1155 / 1156
Socket 775
▶ Please make note of the Lever Slot’s direction when
installing the Clip Support.
Caution
Lever
Slot
Page 7
6
.COM
④ Connect the Fan Connector to the motherboard’s PWM fan header(4-Pin).
M/B
▶ For installations with horizontal Clip
orientation, please be cautious to
not exert excessive force on the fan
while using a screwdrivers to install
the Clip.
Caution
③ Insert a Bolt into both ends of the Intel Clip, then screw each Bolt a little
at a time, alternating between each Bolt, until the Clip is fully installed.
Page 8
7
.COM
③ Connect the Fan Connector to the motherboard’s PWM fan header(4-Pin).
M/B
② Insert the AMD Clip Lever into the AMD Clip’s Clip Lever Slot, then hook
the opposite end on its Lug, press down on the Clip Lever and hook it
onto its Lug.
2) AMD Socket AM3 / AM2+ / AM2 / 754 / 939 / 940 Installation
① Remove any foreign particles from the Base of the the cooler and the
surface of the CPU, then shake well the enclosed thermal grease and
apply a through layer of thermal grease on the surface of the CPU and
the Base of the cooler.
Lug
Page 9
8
.COM
GS1000 / GS1000SE
• E-ATX / Standard ATX / microATX Compatible
* Supports Intel Dual Xeon server motherboards
• UP to 6 Hot Swap HDD Bays
* GS1000(3 Standard / 3 Optional)
* GS1000 SE(Optional)
• Tool-Free HDD Installation
• Airflow Optimized Design
• Vibration Absorbing HDD Dampers and Feet
• The World’s First Roller Rails for Smooth
& Easy PSU Installation
• Cable Compartment Behind the Motherboard
for Cable Management
• Dedicated Fan Compartment for Fanless PSU Users
• Up to a Total of 8 HDD Bays
* 2 Adaptors & Bezels included for use of two 5.25” bays as 3.5” Internal(HDD)/
External(FDD) Bays
GT1000
• High-End Gaming Enclosure Built with Sturdy
All Aluminum Panels
• Three Tool-Free Hinged Magnetic Panels
(2 Left, 1 Right) for Easy Installation and
Access to Components
• Tool-Free Installation of Disk Drives,
Fan Controlles, Audio Interfaces etc.
• Accommodates up to 6 Hard Drives
• Luxurious and Cool Aesthetics.
• Color Option: Black (Red LED Fans),
Titanium (Blue LED Panel).
For more information, please visit our website.
Loading...