* Bearing Type : 2-Ball* Voltage : 5V ~ 11V 2%
* Speed : 1700RPM 10 % (Silent Mode) * Capacity : 6W Maximum
3100RPM10 % (Normal Mode)
* Noise : 20 dB 10% (Silent Mode)
34 dB 10% (Normal Mode)
Note 1)The maximum weight for a heatsink is specified as 450g by Intel for a Pentium 4. Should a
heatsink, which exceeds the relevant weight limit, be installed in a computer, special care should
be taken when moving the computer. Zalman Tech. Co., Ltd. is not responsible for any damage
to a system or a CPU that occurs when moving a computer with an overweight heatsink.
* The specifications of any product may change without prior notice to improve the performance thereof.
1
3. Exploded View
Bolt-B
Air Duct
Bolt-A
Air Duct Base
Fan
Heatsink Duct
Rotating Clip
Heatsink
<Fig. 1. Exploded View>
4. Patent Applications
Patents Applications Pending in over 20 nations around the world,
including the U.S.A., E.U., and Japan
Korean Patent Application Nos. 01-69984, 01-69985 and 02-23963
* The specifications of any product may change without prior notice to improve the performance thereof.
Retention Guide
Static Clip
2
5. Components
1) FHS(Flower HeatSink) Assembly (CNPS5700D)
2) Thermal Grease
3) Adjustable Fan speed Connector (FAN MATE 1)
4) Manual
6. For Use With : INTEL Pentium 4 - Socket 478
1) Silent Mode : Up to 1.8 GHz (Willamette - 0.18 micron)
Up to 2.8 GHz (Northwood - 0.13 micron)
2) Normal Mode : 2.8 GHz and Higher
(2)
Note 1) The ‘Willamette’ CPU was discontinued after the release of the 2.0GHz version.
Note 2) Should you use a CPU faster than 2.8GHz check the Zalman Tech website
(www.zalman.co.kr) for further info.
(1)
Before You Install
1. This product blows air out of the computer system through the Air Duct as shown in Fig. 2.
2. If the Air Duct interferes with other parts of your system, remove it as shown in Fig. 3 before
installation and use.
Exhaust FanAir Duct
Heatsink Duct
<Fig. 2. Airflow Direction> <Fig. 3. Using without Air Duct>
* The specifications of any product may change without prior notice to improve the performance thereof.
3
How to Install
1. Thinly spread the thermal grease on the CPU core’s surface contacting the FHS.
2. Hook the static clips on the mainboard’s Retention Guide as shown in Fig. 5. To identify the static
clips, refer to Fig. 1.
Air Duct
Static Clip
Thermal Grease
Retention Guide
<Fig. 4. Spreading Thermal Grease>
3. Press the Air Duct in the direction of the arrow and make sure the Heatsink Duct is settled onto
the Retention Guide as shown in Fig. 6.
4. While pressing the Air Duct, rotate the rotating clips on the Heatsink Duct and hook them onto
the Retention Guide as shown in Fig. 7. To identify the rotating clips, refer to Fig. 1.
<Fig. 6. Settling Heatsink Duct>
* The specifications of any product may change without prior notice to improve the performance thereof.
<Fig. 5. Hooking Static Clips>
Rotating Clip
Retention Guide
<Fig. 7. Hooking Rotating Clips>
Heatsink Duct
Retention Guide
4
5. Slightly unscrew the Bolt-B on the Air Duct and turn the top part of the duct to the left or right so
that the duct faces the exhaust fan as shown in Fig. 8. Then, screw in three Bolt-B’s tightly to hold
its position.
Caution) If the Air Duct cannot face the exhaust fan as shown in Fig. 8 even after turning
the duct
to the direction
understanding.
Driver
Adjust
fully, separate the duct from the Air Duct Base, make appropriate adjustments
of the duct, and reassemble the duct. See Figs. 2 and 9 for a better
Exhaust Fan
Bolt-B
<Fig. 8. Adjusting the Air Duct><Fig. 9. Assembling the Duct>
6. Connect FAN MATE 1 to the mainboard & the fan as shown in Fig. 10.
3-Pin Connector
Mainboard
FAN MATE 1
Speed Control Knob
3-Pin Connector
(from CNPS 5700D)
<Fig. 10. Connecting FAN MATE 1>
* The specifications of any product may change without prior notice to improve the performance thereof.
5
Usage & Caution
1. When Adjusting the Fan Speed
The exhaust fan must be at the same speed or faster than the CPU cooler’s fan in order for this
product to perform optimally. Having a slower exhaust fan can cause a drop in the cooling
performance of the product.
2. Checking CPU Compatibility & Using FAN MATE 1
Read ‘For Use With’ section and make sure your CPU is compatible before using the CPUcooler.
When the speed control knob on FAN MATE 1 is turned fully counter-clockwise, the fan operates
in Silent Mode at a minimum speed. When it is turned fully clockwise, it operates in Normal Mode.
You can select the desired fan speed by turning the knob.
Caution)
3. Cautions During Booting
When booting the computer, it may automatically power down after an alarm sound is generated
by a system monitoring program to indicate that the the CPU fan is rotating slowly. If this happens,
you may turn the speed control knob fully clockwise to increase the fan speed and set “CPU Fan
Detected” to “Disabled” in the BIOS settings, or set the slowest rotation of the CPU fan in the
system monitoring program to less than or equal to 1500RPM.
Caution)
4. If you remove the Air Duct, cooling performance may deteriorate.
5. Creating a Complete Noiseless System
Use the following Zalman products to achieve stable and silent operation of your computer :
Noiseless Power Supply, CNPS series CPU Cooler, Fanless Cooler for Northbridge Chipset &
Video Card and Noiseless Fan.
For more inquiries regarding our products, visit our website(www.zalman.co.kr).
FAN MATE 1 has been specifically designed to be used with the fan of this product.
Zalman Tech. Co., Ltd. is not responsible for any damage caused to systems or CPUs
when using FAN MATE 1 with other types of fans.
Some mainboards do not boot if the rotation of the CPU fan is below a certain RPM.
If the BIOS is updated, Silent Mode can be used. For more information on updating
BIOS, please refer to your mainboard manufacturer’s web site. Even in a case where
the RPM of fans does not get measured in Silent Mode, performance will not be affected.
* The specifications of any product may change without prior notice to improve the performance thereof.
6
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.