Zalman CNPS9500A User Manual

Users Manual
CNPS9500A LED
AMD Socket FM2/FM1/AM3+/AM3/AM2+/AM2 CPU & APUs
Intel Socket 1155/1156/1151/1150/775 CPUs
To ensure safe and easy installation, please read the following precautions.
www.ZALMAN.com
Ver.150811
1. Precautions
1) Use and keep product away from reach of children and pets.
2) Do not ingest the Thermal Grease, and avoid its contact with skin and eyes. If contact is made with skin, wash off with water. If ingested or irritation persists, seek medical attention.
3) To prevent possible injuries, gloves must be worn while handling this product.
4) Excessive force exerted on the fan may cause damage to the fan and/ or system.
5) Avoid inserting objects or hands into the fan while it is in operation to prevent product damage and injuries.
6) Check the components list and condition of the product before installation. If any problem is found, contact the retailer to obtain a replacement.
7) Zalman Tech Co., Ltd. is not responsible for any damages due to overclocking.
8) During transportation of the system, the cooler must be removed. Zalman is not responsible for any damages that occur during the transport of a system.
9) Product design and specifications may be revised to improve quality and performance.
Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages due
to external causes, including but not limited to, improper use, problems with electrical power, accident, neglect, alteration, repair, improper installation, or improper testing.
2. Specifications
Spec.
Mate 2
Model
Material Pure Copper
Weight 530g
Dimensions 85(L) 112(W) 125(H)
Bearing-Type 2 Ball-Bearing
Fan
Fan
RPM 1,350rpm ~ 2,600rpm ± 10%
Noise Level 18.5 ~ 27.5dBA ± 10%
Input Voltage 12V
Output Voltage 5 ~ 11V ± 2%
Maximum Capacity Up to 6W
CNPS9500A LED
.COM
3. Components
1) Common Components
Cooler
Fan Mate 2 CableFan Mate 2 Double-Sided Tape
2) Intel Components
Clip Support
Washers
3) AMD Components
Users Manual Clip
Clip Support Fixing Bolts
Nuts
AMD Clip Lever
Thermal Grease
(ZM-STG2M)
Intel Clip Lever
Clip Fixing Bolts
.COM
4. Installation Requirements
1) Space Requirements
The coolers installation requires unobstructed space with dimensions of 155 (width), 88(length), 128(height), and the CPU as a central reference point. Please check if components such as ODDs and PSU protrude into the required space.
2) Air Guide Removal
Air guides on enclosures must be removed, before the coolers installation, for they protrude into the coolers required space.
88
128
115
3) Cooler Orientation
It is recommended that the cooler be installed so that air flows from the cooler toward
the enclosures rear exhaust fan.
PSU
.COM
4) Installation Based On Clip Orientation
A. Horizontal Clip Orientation
B. Vertical Clip Orientation
.COM
5. Installation
1) Intel Socket 1155 / 1156 / 1151 / 1150 / 775 Installation
Install the Clip Support to the motherboard according to the socket-type.
Bolt(silver)
Clip Support
Washer
Nut
M/B
Socket 1155 / 1156/ 1151 /1150
Socket 775
Caution
Lever Slot
Please make note of the Lever Slots direction when
installing the Clip Support.
Clear off any particles or residue from the CPUs surface then spread
a thorough layer of Thermal Grease on the CPU and the base of the cooler.
.COM
Refer to page 4 Installation Based On Clip Orientation and position the
Clip over the coolers Base Cover.
Insert the Intel Clip Lever into the Clips Lever Slot then hook on the
Clips opposite end onto the Lug marked with the arrow head. Press down the Clip Lever and hook on the Clip Lever onto its Lug.
Refer to Section 6 Fan Mate 2 Installation and Usage for instructions on
power connection.
2) AMD Socket FM2/FM1/AM3+/AM3/AM2+/AM2 Installation
Clear off any particles or residue from the CPUs surface then spread
a thorough layer of Thermal Grease on the CPU and the base of the cooler.
Refer to page 4 Installation Based On Clip Orientation and position the
Clip over the coolers Base Cover.
.COM
Insert the AMD Clip Lever into the Clips Lever Slot then hook on the
Clips opposite end onto its Lug. Press down on the Clip Lever and hook on the Clip Lever onto its Lug.
Refer to Section 6 Fan Mate 2 Installation and Usage for instructions on
power connection.
6. Fan Mate 2 Installation and Usage
1) Fan Mate 2 Installation
Connect Fan Mate 2 between the
Fan Cable and the motherboard as shown in the diagram below.
Fan Mate 2 can be installed to the
side of the case using Double-Sided Tape.
M/B
Fan Connector (Cooler)
.COM
Double-Sided Tape
2) Fan Mate 2 Operation
Adjust the Fan Speed Control Knob for RPM control.
Fan Speed Control Knob
BIOS Booting Error
In the case that you get a BIOS error beep: Rotate the Fan Speed Control Knob clockwise to the maximum setting. Disable CPU Fan Detected in BIOS setting or set the system monitoring
programs CPU Fan RPM to the lowest setting.
Certain motherboards will not boot if the CPU fans RPM is not detected. In this
case inquire to the motherboards manufacturer for additional details.
.COM
Loading...