Yamaha RX-V2071 Owner Manual

AV Receiver
Owner’s Manual
English for Oceania
Be sure to read “Safety Brochure” (supplied booklet) before using this unit.
En 1
CONTENTS
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
FEATURES
What you can do with this unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Front display (indicators) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
SETUP
General setup procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1 Connecting speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Basic speaker configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Advanced speaker configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Input/output jacks and cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2 Connecting a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3 Connecting playback devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Connecting video devices (BD/DVD players, etc.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Connecting audio devices (CD players, etc.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Connecting to the jacks on the front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
4 Connecting the FM/AM antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
5 Connecting to the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6 Connecting other devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Connecting video/audio recording devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Connecting a device with analog multi-channel output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Connecting a device compatible with SCENE link playback (remote connection) . . . . . . . . . . . . . . . . . . .42
Connecting a device compatible with the trigger function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
7 Connecting the power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
8 Selecting an on-screen menu language . . . . . . . . . . . . . . . . . . . . . . . . 44
9 Optimizing the speaker settings automatically (YPAO) . . . . . . . . . 45
Measuring at one listening position (single measure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Measuring at multiple listening positions (multi measure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Checking the measurement results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Reloading the previous YPAO results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Warning messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
PLAYBACK
Basic playback procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Selecting an HDMI output jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Selecting the input source and favorite settings at once (SCENE) . . 53
Configuring scene assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Selecting the sound mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Enjoying sound field effects (CINEMA DSP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Enjoying unprocessed playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Enjoying pure high fidelity sound (Pure Direct) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Enjoying compressed music with enhanced sound (Compressed Music Enhancer) . . . . . . . . . . . . . . . . . 59
Enjoying surround sound with headphones (SILENT CINEMA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Listening to FM/AM radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Selecting a frequency for reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Registering favorite radio stations (preset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Operating the radio on the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Playing back iPod music/videos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Connecting an iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Playback of iPod contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Playing back music via Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Connecting a Bluetooth receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Pairing Bluetooth components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Establishing a wireless connection and playing back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
En 2
Playing back music stored on a USB storage device . . . . . . . . . . . . . . 70
Connecting a USB storage device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Playback of USB storage device contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Playing back music stored on PCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Media sharing setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Playback of PC music contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Listening to Internet radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Playing back music in multiple rooms (multi-zone) . . . . . . . . . . . . . . . 78
Preparing for Zone2 or Zone3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Controlling Zone2 or Zone3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Useful functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Registering favorite items (shortcut) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Controlling this unit from the web browser (web control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Viewing the current status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Configuring settings in accordance with a playback source (Option menu)
Option menu items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
. . . 88
CONFIGURATIONS
Configuring input sources (Input menu) . . . . . . . . . . . . . . . . . . . . . . . . . 91
Input menu items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Configuring the SCENE function (Scene menu) . . . . . . . . . . . . . . . . . . . 93
Scene menu items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Configuring sound programs/surround decoders (Sound Program menu)
Sound Program menu items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Configuring various functions (Setup menu) . . . . . . . . . . . . . . . . . . . . . 99
Setup menu items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Speaker (Manual Setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Multi Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
. . . . 96
Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Viewing information about this unit (Information menu) . . . . . . . . 116
Types of information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Configuring the system settings (ADVANCED SETUP menu) . . . . . 117
ADVANCED SETUP menu items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Changing the speaker impedance setting (SPEAKER IMP.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Turning on/off the remote control sensor (REMOTE SENSOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Selecting the remote control ID (REMOTE CON AMP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Switching the video signal type (TV FORMAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Removing the limitation on HDMI video output (MONITOR CHECK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Backing up/recovering the settings (RECOV./BACKUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Restoring the default settings (INITIALIZE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Updating the firmware (FIRM UPDATE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Checking the firmware version (VERSION) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Controlling external devices with the remote control . . . . . . . . . . . 121
Setting remote control codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Programming from other remote controls (learning) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Editing device names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Operating multiple functions at once (macro) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Resetting the remote control configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Using the simplified remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Updating the firmware of this unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
En 3
APPENDIX
Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Power and system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
FM/AM radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
USB and network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Error indications on the front display . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Audio information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Video information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Video signal flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Information on HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
HDMI Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
HDMI signal compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Reference diagram (rear panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
En 4

Accessories

Check that the following accessories are supplied with this product.
Remote control Batteries (AAA, R03, UM-4) (x 4)
Insert into the remote control in the correct polarity (+/-)
Operating range of the remote control
• Aim the remote control directly at the remote control sensor on this unit during operation.
Within 6 m
30° 30°
Simplified
Power cable
YPAO microphone
remote control
* The figure of the supplied power
cable differs depending on regions.
AM antenna FM antenna
* The figure of the supplied FM antenna differs depending
on regions.
Easy Setup Guide Safety Brochure
CD-ROM (Owner’s Manual)
• Some features are not available in certain regions.
• Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and product, the product has priority.
• This manual mainly explains operations using the supplied remote control.
• This manual describes both the “iPod” and “iPhone” as the “iPod”. “iPod” means both “iPod” and “iPhone” unless the explanation describes exceptions.
• “ ” indicates the cautions concerning operations or setup of the unit.
• “ ” indicates the explanations for better use.
En 5

FEATURES

What you can do with this unit

Ready for any kind of contents iPod
USB
*Requires optional Bluetooth receiver for playback via Bluetooth
p.63
p.70
iPod
USB device
BD/DVD player
Network
Bluetooth
Network contents
Audio
via Bluetooth
HDMI Control
Audio/Video
p.73 to p.76
p.68
Speakers
Audio
Supports 2 to 9 channel speaker system and up to 2 subwoofer connections. Allows you to enjoy favorite acoustic spaces in various styles.
Plus, bi-amp connections, channel expansion (with external power-amp)
p.21
and multi-zone configurations to enhance your system
Automatically optimizing the speaker settings to suit your room (YPAO)
Sound field reproductions like actual movie theaters and concert halls from
p.45
p.56
stereo or multi-channel audio sources (CINEMA DSP)
Enjoying compressed music with enhanced sound (Compressed Music
p.59
Enhancer)
HDMI Control
Audio
Video
TV
Operating external devices with the supplied remote control
p.121
Remote control of this unit
AV receiver (this unit)
Selecting the input source and favorite settings at once (SCENE)
p.53
TV remote control
Operating the TV, AV receiver and BD/DVD player in combination (HDMI Control)
p.142
En 6

Full of useful functions!

Connecting various devices (p.35)
A number of HDMI jacks and various input/output jacks on this unit allow you to connect video devices such as BD/DVD players, audio devices such as CD players, game consoles and camcorders, and so on.
Turntable
BD/DVD
player
Game
console
Camcorder
CD player
TV
Creating stereoscopic sound fields (p.58)
Connection of presence speakers enables to create a natural stereoscopic sound field in your room (CINEMA DSP 3D). Even when no presence speakers are connected, this unit automatically creates Virtual Presence Speaker (VPS) to produce 3D surround sound.

At time like this

I want to connect a playback device using HDMI for video and non-HDMI for audio...
Use “Audio Select” in the “Option” menu to specify the type of an audio input jack to be used for the corresponding input source (p.90).
Video and audio are not synchronized...
Use “Lipsync” in the “Setup” menu to adjust the delay between video and audio output (p.106).
I want to hear audio from the TV speakers...
Use “Audio Output” in the “Setup” menu to select whether to output audio signals through this unit and the TV (p.110).
I want to this unit to be turned off automatically when not in use...
Use “Auto Power Down” in the “Setup” menu to set the amount of time for auto-standby (p.113).
I want to change the on-screen menu language...
Use “Language” in the “Setup” menu to select a language from English, Japanese, French, German, Spanish and Russian (p.115).
Playing back TV audio in surround sound
with a single HDMI cable connection (Audio Return Channel: ARC) (p.29)
When using a TV that supports ARC, you only need a single HDMI cable to connect the TV and this unit to output video to the TV, input audio from the TV, and transmit HDMI Control signals.
HDMI Control
TV audio
Video from
external device
Listening to FM/AM radio (p.60)
This unit is equipped with the built-in FM/AM tuner. You can register favorite radio stations as presets.
Enjoying pure high fidelity sound (p.59)
When the Pure Direct mode is enabled, this unit plays back the selected source with the least circuitry. It allows you to enjoy Hi-Fi sound quality.
Easy operation with a TV screen
You can navigate the various contents (iPod, USB, network, etc.), view the information, or configure the settings using the on-screen menu.
I want to update the firmware...
Use “UPDATE” in the “ADVANCED SETUP” menu to update the firmware of this unit (p.120). If this unit is connected to the Internet, the corresponding message will be displayed on the TV when a newer firmware is available (p.130).
There are many other settings to customize this unit. For details, see the following pages.
Input settings (p.91)
Scene settings (p.94)
Sound program and surround decoder settings (p.97)
Various function settings (p.100)
Information view (audio signal, video signal, etc.) (p.116)
System settings (p.118)
En 7

Part names and functions

Front panel

MAIN ZONE
6 7 8
1 MAIN ZONE
Turns on/off (standby) this unit.
2 Standby indicator
Lights up when this unit is in standby mode under any of the following conditions.
- HDMI Control is enabled (p.142)
- The standby through function is enabled (p.110)
- The network standby function is enabled (p.111)
- The iPod is being charged (p.92)
- An iPod wireless system is connected (p.64)
3 Front display
Displays information (p.10).
4 Remote control sensor
Receives remote control signals (p.5).
5 PURE DIRECT
Enables/disables Pure Direct (p.59).
6 INPUT
Selects an input source.
NATURAL SOUND AV RECEIVER RX-V2071
7 Front panel door
8 VOLUME
TONE/BALANCEOPTIONON SCREEN
STRAIGHT
ENTER
PROGRAM FM AM TUNING/CH
DISPLAYRETURN
PHONES
USB
YPAO MIC
SILENT CINEMA
iPod/iPhone
1
ZONE 2
SCENE
2 3 4
MULTI ZONE
ZONE 3
VIDEO AUX
ZONE CONTROL
ROPTICALL AUDIOVIDEOS VIDEO
For protecting controls and jacks (p.9).
Adjusts the volume.
INFO MEMORY
4
PRESET
HDMI IN
5321
PURE DIRECT
VOLUMEINPUT
Opening the front panel door
• To use controls or jacks behind the front panel door, gently press the bottom of the door to open it. Keep the door closed when not using controls or jacks behind the front panel door.
En 8
Inside of the front panel cover
SCENE
MULTI ZONE
HDMI IN
VIDEO AUX
TONE/BALANCEOPTIONON SCREEN
DISPLAYRETURN
STRAIGHT
1
ENTER
ZONE 2
2 3 4
ZONE CONTROL
INFO MEMORY
YPAO MIC
PHONES
SILENT CINEMA
USB
iPod/iPhone
PROGRAM FM AM TUNING/CH
PRESET
R OPTICALL AUDIOVIDEOS VIDEO
ZONE 3
9 ON SCREEN
Displays the on-screen menu on the TV.
0 Menu operation keys
Cursor keys Select a menu or parameter. ENTER Confirms a selected item. RETURN Returns to the previous screen.
A OPTION
Displays the option menu (p.88).
B DISPLAY
Display the status information on the TV (p.87).
C TONE/BALANCE
Adjusts the high-frequency range and low-frequency range of sounds output from speakers and headphones (p.89). Adjusts the right/left channel volume balance for Zone2 or Zone3 (p.83).
D STRAIGHT
Enables/disables the straight decode mode (p.58).
9 0 A CB D E F H I KJ L
G
M N O P
E PROGRAM
Selects a sound program or a surround decoder (p.55).
F SCENE
Selects the registered input source, sound program, HDMI output and various settings at once. Additionally, you can turn on this unit when it is in standby mode (p.53).
G MULTI ZONE
ZONE 2~3 Enables/disables the audio output to
ZONE CONTROL Switches the zones (main, Zone2 or
each zone (p.82).
Zone3) to operate with the front panel controllers (p.82).
H INFO
Selects the information displayed on the front display (p.87).
I MEMORY
Registers FM/AM radio stations as preset stations (p.60). Registers USB/network contents as shortcuts (p.84).
J FM/AM
Switches between FM and AM (p.60).
K PRESET
Selects a preset FM/AM radio station (p.61). Selects a USB/network content from shortcuts (p.84).
L TUNING/CH
Selects the radio frequency (p.60).
M USB jack
For connecting a USB storage device (p.70) or an iPod via USB (p.63).
N YPAO MIC jack
For connecting the supplied YPAO microphone (p.45).
O PHONES jack
For connecting headphones.
P VIDEO AUX jacks
For connecting camcorders, game consoles, etc (p.38).
En 9

Front display (indicators)

2
1 43
STEREO
TUNED PARTY
ZONE
ZONE
2
OUT 1INOUT 2
ENHANCER
9 BCB
SLEEP
0
3
3
A
1 HDMI
Lights up during normal HDMI communication.
IN
Lights up when HDMI signals are being input.
OUT1/OUT2
Indicate the HDMI OUT jacks currently outputting an HDMI signal.
2 STEREO
Lights up when this unit is receiving a stereo FM radio signal.
TUNED
Lights up when this unit is receiving an FM/AM radio station signal.
3 ZONE indicators
Light up when the audio output to Zone2 or Zone3 is enabled.
4 PA RT Y
Lights up when this unit is in the party mode.
5 Information display
Displays the current status (input name, sound mode name, etc). You can switch the information by pressing INFO (p.87).
5
6 MUTE
Flashes when audio is muted.
7 Volume indicator
Indicates the current volume.
8 ADAPTIVE DRC
Lights up when Adaptive DRC (p.89) is working.
9 ENHANCER
Lights up when Compressed Music Enhancer (p.59) is working.
0 CINEMA DSP
Lights up when CINEMA DSP (p.56) is working.
CINEMA DSP
Lights up when CINEMA DSP 3D (p.58) is working.
A SLEEP
Lights up when the sleep timer is on.
B Cursor indicators
Indicate the remote control cursor keys currently operational.
3
876
VOLUME
MUTE
PL
C Speaker indicators
Indicate speaker terminals from which signals are output.
Front speaker (L)
Front speaker (R)
Center speaker
Surround speaker (L)
Surround speaker (R)
Surround back speaker (L)
Surround back speaker (R)
Surround back speaker
Front/rear presence speakers (L)
Front/rear presence speakers (R)
Subwoofer (1)
Subwoofer (2)
DRCADAPTIVE
CL R
SW1SLSW2
SBLPL SBRSB PR
PR SR
En 10

Rear panel

2
DOCK
(1 BD/DVD)
PHONO
GND
L
R
1
1 PHONO jacks
For connecting a turntable (p.37).
2 DOCK jack
For connecting an optional Yamaha products such as iPod dock (p.64), iPod wireless system (p.64), and Bluetooth receiver (p.68).
3 AV1~4 jacks
For connecting video/audio playback devices to input video/ audio signals (p.35).
4 NETWORK jack
For connecting to the network (p.40).
5 AV OUT jacks
For outputting video/audio to a recording device (VCR, tape deck, etc.) (p.41).
6 MONITOR OUT/ZONE OUT
(composite video/S-video) jacks
For connecting a TV compatible with composite video or S-video to output video signals (p.33). For connecting a zone video monitor (p.80).
7 HDMI OUT 1~2 jacks
For connecting HDMI-compatible TVs to output video/audio signals (p.29). When using ARC, TV audio signal is input through the HDMI OUT 1 jack.
4
NETWORK
AV 1
AV 3 AV 4AV 2
AV OUT
3
2
COAXIAL
COAXIAL
ANTENNA
(4 RADIO)
OPTICAL4OPTICAL
AM
FM
75Ω
AUDIO 1
(2 TV)
5
OPTICAL
1
MONITOR OUT/
ZONE OUT
(3 CD)
6
COAXIAL
ARC
7
HDMI OUT
AV 1
AV 2
AUDIO 3AUDIO 2
2
YP
A
B
AUDIO 4
SURROUND
R L
CENTER
SUBWOOFER
SINGLE
C
D
ZONE 2 ZONE 3FRONT
L
HDMI
YPB PR
ZONE OUT
ZONE 2/ZONE 3/R.PRESENCE
R
MONITOR OUT/ZONE OUT
PRE OUT
FRONT
SURROUND SUR. BACK
SPEAKERS
EXTRA SP2
AV 2 AV 3 AV 4 AV 5 AV 6 AV 7
AV 1
(1 BD/DVD)
COMPONENT VIDEO
B PR
YPB PR
AV 3
AV 4
MULTI CH INPUT
SURROUND SUR. BACK
SURROUND BACK
R
1
IN OUT2IN OUT
(SINGLE) (FRONT)
(REAR)
SUBWOOFER
CENTER FRONT
L
REMOTE
1
2
CENTER
R
SPEAKER IMPEDANCE
TRIGGER
OUT
+12V 0.1A MAX.
L
1
2
ZONE 2/ZONE 3/F.PRESENCE/ BI–AMP
R
C1 53 6 8 9 0 A B
RS-232C
EXTRA SP1
AC IN
L
D E F G H I J
8 COMPONENT VIDEO (AV1~4) jacks
For connecting video playback devices compatible with component video to input video signals (p.36).
9 HDMI (AV1~7) jacks
For connecting HDMI-compatible playback devices to input video/audio signals (p.35).
0 MONITOR OUT/ZONE OUT
(component video) jacks
For connecting a TV compatible with component video to output video signals (p.33). For connecting a zone video monitor (p.80).
A REMOTE 1~2 (IN/OUT) jacks
For connecting a Yamaha product compatible with SCENE link playback (p.42), or connecting an infrared signal receiver/emitter to operate devices including this unit from another room (p.81).
B TRIGGER OUT 1~2 jacks
For connecting devices that support the trigger function (p.42).
C RS-232C terminal
This is a control expansion terminal for custom installation. Consult your dealer for details.
D ANTENNA jacks
For connecting FM and AM antennas (p.39).
E AUDIO1~4 jacks
For connecting audio playback devices to input audio signals (p.37).
F MULTI CH INPUT jacks
For connecting a device that supports multi-channel output to input audio signals (p.41).
G ZONE OUT jacks
For connecting an external amplifier used in Zone2 or Zone3 to output audio signals (p.79).
H PRE OUT jacks
For connecting subwoofers with built-in amplifier (p.20) or an external power amplifier (p.27).
I SPEAKERS terminals
For connecting speakers (p.15).
J AC IN
For connecting the supplied power cable (p.43).
En 11

Remote control

1
SOURCE
2
RECEIVER
3
AV
1 2 3 4
MUTE
ENTER
USB NET
VOLUME
POP-UP/MENU
OPTION
V-AUX
D
E
F
5 6 7
4
5
6 C
7
8
AUDIO
1 2 3 4
MULTI
PHONO
TUNER
DOCK [ B ][ A ]
SCENE
1 2 3 4
PROGRAM
TOP MENU
ON SCREEN
9
RETURN DISPLAY
0
MODE
7
LIVE
A
B
PRESET
INPUT
MUTE
CLASSICAL
MOVIE
TV
TV VOL
ENTERTAIN
CLUB
STEREO STRAIGHT
PURE DIRECT
TV CH
G
1 Remote control signal transmitter
Transmits infrared signals.
2 SOURCE
Turns on/off an external device.
SOURCE/RECEIVER
Switches the devices (this unit or external device) to operate with the remote control (p.123). You can operate this unit when this key lights up in orange, and an external device when this key lights up in green.
RECEIVER
Turns on/off (standby) this unit.
3 Display window
Displays remote control information.
4 Input selection keys
Select an input source to play back.
AV1 ~7 AV1~7 jacks V-A UX VIDEO AUX jacks (on the front panel) AUDIO1~4 AUDIO1~4 jacks PHONO PHONO jacks MULTI MULTI CH INPUT jacks USB USB jack (on the front panel) NET NETWORK jack (press repeatedly to select a
DOCK DOCK jack TUNER FM/AM radio [A], [B] Changes the external device to operate with the
desired network source)
remote control without switching the input source.
5 SCENE
Selects the assigned input source, sound program, HDMI output and various settings at once. Additionally, you can turn on this unit when it is in standby mode (p.53).
6 PROGRAM
Selects a sound program (p.55).
7 External device operation keys
Operate playback and menu display etc. for external devices (p.123).
8 ON SCREEN
Displays the on-screen menu on the TV.
9 Menu operation keys
Cursor keys Select a menu or a parameter. ENTER Confirms a selected item. RETURN Returns to the previous screen.
0 MODE
Switches between stereo and monaural for FM radio reception. Switches the iPod operation modes (p.66).
A PRESET
Selects a preset FM/AM radio station (p.61). Selects a USB/network content from shortcuts (p.84).
B TV operation keys
Operate TV input, TV volume, etc (p.122).
C VOLUM E
Adjusts the volume.
D MUTE
Mutes the audio output.
E OPTION
Displays the option menu (p.88).
F DISPLAY
Displays the status information on the TV (p.87).
G Sound mode keys
Select a sound mode (p.55).
En 12
Inside of the remote control cover
SOURCE
RECEIVER
AV
1 2 3 4
USB NET
MUTE
VOLUME
POP-UP/MENU
ENTER
PART Y
FM
LIVE
CLUB
STEREO STRAIGHT
9
TV CH
V-AUX
OPTION
HDMI OUT
ENTERTAIN
TUN./ CH
PURE
SLEEP
DIRECT
LEVELENT
SETUPZONE
L M
N
O P
Q
H I
J
K
5 6 7
AUDIO
1 2 3 4
MULTI
PHONO
TUNER
DOCK [ B ][ A ]
SCENE
1 2 3 4
PROGRAM
TOP MENU
ON SCREEN
RETURN DISPLAY
SUR.
ENHANCER
MODE
DECODE
MEMORY
INFO AM
2 3
1
CLASSICAL
PRESET
5
4 6
MOVIE
TV
87
INPUT
TV VOL
MUTE
0
10
H Sound mode keys
Select a sound mode (p.55).
I INFO
Selects the information displayed on the front display (p.87).
J Numeric keys
Enter numerical values such as radio frequencies.
K ZONE
Switches the zones (main, Zone2 or Zone3) to operate with the remote control (p.82).
L PA RT Y
Turns on/off the party mode (p.83).
M HDMI OUT
Selects HDMI OUT jacks to be used for video/audio output (p.52).
N Radio keys
Operate the FM/AM radio when “TUNER” is selected as the input source.
MEMORY Registers FM/AM radio stations as presets. FM Switches to FM radio. AM Switches to AM radio. TUN./CH Selects the radio frequency.
O SLEEP
Switches this unit to standby mode automatically after a specified period of time has elapsed (sleep timer). Press repeatedly to set the time (120 min, 90 min, 60 min, 30 min, off).
P LEVEL
Adjusts the volume of each speaker (p.104).
Q SETUP
Switches the remote control to the setup mode (p.121)
• To operate external devices with the remote control, register a remote control code for each device in advance (p.121).
En 13

SETUP

General setup procedure

1 Connecting speakers (p.15)
2 Connecting a TV (p.29)
3 Connecting playback devices (p.35)
4 Connecting the FM/AM antennas (p.39)
5 Connecting to the network (p.40)
6 Connecting other devices (p.41)
7 Connecting the power cable (p.43)
8
Selecting an on-screen menu language (p.44)
Basic speaker configuration (p.16)
Select the speaker layout and connect the speakers to this unit.
Advanced speaker configuration (p.21)
Apply bi-amp connections, channel expansion (using an external power amplifier) or multi-zone configurations to enhance the system.
Connect a TV to this unit.
Connect video devices (BD/DVD players, etc.) and audio devices (CD players, etc.) to this unit.
Connect the supplied FM/AM antennas to this unit.
Connect this unit to the network.
Connect external devices such as recording devices.
After all the connections are complete, plug in the power cable.
Select a desired on-screen menu language (default: English).
9
Optimizing the speaker settings automatically (YPAO) (p.45)
Now all the preparations are complete. Enjoy playing movies, music, radio, etc. with this unit!
Optimize the speaker settings such as volume balance and acoustic parameters to suit your room (YPAO).
En 14
Speaker connections
1
2 3 4 5 6 7 8 9
1 Connecting speakers
This unit has 9 built-in amplifiers. You can connect 2 to 11 speakers and up to 2 subwoofers (with built-in amplifier) to create the favorite acoustic space in your room.
You can also apply bi-amp connections, channel expansion (using an external power amplifier) or multi-zone configurations to enhance your system (p.21).
Caution
• This unit is configured for 8-ohm speakers at the factory. When connecting 6-ohm speakers, set the speaker impedance of this unit to “6 Ω MIN”. In this case, you can also use 4-ohm speakers as the front speakers. For details, see “Setting the speaker impedance” (p.18).
Functions of each speaker
Speaker type Abbr. Function
Front (L)
Front (R)
Center Produces center channel sounds (dialogs, vocals, etc).
Surround (L) Produce surround right/left channel sounds. Surround speakers also
Surround (R)
Surround back (L)
Surround back (R)
Front presence (L)
Front presence (R)
Rear presence (L)
Rear presence (R)
Subwoofer
• We recommend using presence speakers to have a full effect of the stereoscopic sound fields. However, this unit creates Virtual Presence Speaker (VPS) using the front, center and surround speakers to produce stereoscopic sound fields even when no presence speakers are connected (p.58).
• Use “Ideal speaker layout” (diagram on the right) as reference. You do not need to exactly adjust the speaker layout to this diagram since the YPAO function of this unit will automatically optimize the speaker settings (distance, etc.) to suit the speaker layout.
• When using only one surround back speaker, place it straight behind the listening position (middle of “SBL” and “SBR” in the diagram).
Produce front right/left channel sounds (stereo sounds).
produce surround back channel sounds when no surround back speakers are connected.
Produce surround back right/left channel sounds. When no surround back speakers are connected, Surround back channel sounds are produced from the surround speakers.
Produce CINEMA DSP effect sounds. In combination with CINEMA DSP 3D (p.58), the presence speakers create a natural stereoscopic sound field in your room.
Produces LFE (low-frequency effect) channel sounds and reinforces bass parts of other channels. This channel is counted as “0.1”. You can connect 2 subwoofers (with built-in amplifier) to this unit and place them on the right/left (or front/ rear) sides of the room.
Ideal speaker layout
1.8 m
0.5 to 1 m
30 cm or more
0.5 to 1 m
1.8 m
10°~30°10°~30°
1.8 m1.8 m
En 15
Speaker connections
1
2 3 4 5 6 7 8 9

Basic speaker configuration

Placing speakers in your room
Depending on the number of speakers, place the speakers and subwoofer (with built-in amplifier) in your room. This section describes the representative speaker layout examples.
9.2+2 channel system
(using both surround back and rear presence speakers)
This speaker system brings out the full performance of this unit and allows you to enjoy a highly-natural stereoscopic sound field with any contents.
• The surround back speakers and rear presence speakers do not produce sounds simultaneously. This unit automatically switches the speakers to be used depending on a selected CINEMA DSP (p.56).
9.2 channel system (using rear presence speakers)
This speaker system uses the front and rear presence speakers to produce a highly­natural stereoscopic sound field, and is suited for enjoying 5.1-channel contents.
9.2 channel system (using surround back speakers)
This speaker system uses the front presence speakers to produce a natural stereoscopic sound field, and also allows you to enjoy extended surround sounds using the surround back speakers.
En 16
Speaker connections
1
2 3 4 5 6 7 8 9
7.1 channel system (using front presence speakers)
This speaker system uses the front presence speakers to produce a natural stereoscopic sound field, and is suited for enjoying 5.1-channel contents.
7.1 channel system (using surround back speakers)
5.1 channel system
This speaker system creates Virtual Presence Speaker (VPS) using the front, center and surround speakers to produce a stereoscopic sound field, and is suited for enjoying
5.1-channel contents.
2.1 channel system
This speaker system creates Virtual Presence Speaker (VPS) using the front, center and surround speakers to produce a stereoscopic sound field, and also allows you to enjoy extended surround sounds using the surround back speakers.
Even when no surround speakers are connected, this unit creates the virtual surround speakers using the front speakers to allow you to enjoy multi-channel surround sound (Virtual CINEMA DSP).
• Add the center speaker to configure a 3.1-channel system.
En 17
Speaker connections
1
2 3 4 5 6 7 8 9
Setting the speaker impedance
This unit is configured for 8-ohm speakers at the factory. When connecting 6-ohm speakers, set the speaker impedance to “6 Ω MIN”. In this case, you can also use 4-ohm speakers as the front speakers.
Before connecting speakers, connect the supplied power cable to
1
this unit and then to an AC wall outlet.
While holding down STRAIGHT on the front panel, press
2
MAIN ZONE .
MAIN ZONE
Check that “SPEAKER IMP.” is displayed on the front display.
3
DOCK TAG
SPIMP.-
HD
STEREO
TUNED
PRE
AMP
ZONE
ZONE3ZONE
2
4
OUT 1INOUT 2
ENHANCER
SLEEP
3
HD
Press STRAIGHT to select “6 Ω MIN”.
4
Press MAIN ZONE to set this unit to standby mode and remove the
5
STRAIGHT
SPEAKERIMP.
PARTY
8MIN
MUTE
PL
VOLUME
CL R
SW1SLSW2SW SBLPL SBRSB PR
DRCADAPTIVE
PR SR
power cable from the AC wall outlet.
Now you are ready to connect the speakers.
En 18
1
2
AUDIO 4
MULTI CH INPUT
ZONE OUT
AUDIO 3
CENTER
SUBWOOFER
ZONE 2 ZONE 3FRONT
SURROUND SUR. BACK
SPEAKERS
CENTER FRONT
SPEAKER IMPEDANCE
ZONE 2/ZONE 3/R.PRESENCE
SURROUND BACK
BI–AMP
ZONE 2/ZONE 3/F.PRESENCE/
R L
SURROUND
R L
R
R
R
L
L
L
PRE OUT
SUBWOOFER
CENTER
FRONT
SURROUND SUR. BACK
(SINGLE) (FRONT)
(REAR)
EXTRA SP1EXTRA SP2
SINGLE
Speaker connections
1
2 3 4 5 6 7 8 9
Connecting speakers
Connect the speakers placed in your room to this unit.
Caution
• Remove the power cable of this unit from an AC wall outlet and turn off the subwoofer before connecting the speakers.
• Be careful that the core of the speaker cable does not touch anything or come into contact with the metal areas of this unit. This may damage this unit or the speakers. If the speaker cables short circuit, “CHECK SP WIRES” will appear on the front display when this unit is turned on.
Speakers to be connected
Speaker system
Room Speaker type Abbr.
(the number of channels)
9+2 9 7 5 2
Front (L) ●●●●●
Front (R) ●●●●●
Center ●●●●
Surround (L) ●●●●
Surround (R) ●●●●
Main zone
Surround back (L) {*1 {*3
Surround back (R) {*1 {*3
Front presence (L) ●●{*4
Front presence (R) ●●{*4
Rear presence (L) {*2
Rear presence (R) {*2
If you have 9 speakers, use two of them as surround back speakers (*1) or rear presence speakers (*2). If you have 7 speakers, use two of them as surround back speakers (*3) or front presence speakers (*4).
Power Am p
Assign (p.102)
Basic (default)
Cables necessary for connection (commercially available)
Speaker cables (x the number of speakers)
+ –
+ –
Audio pin cable (2 for connecting 2 subwoofers)
Connection diagram
Refer to the following diagram and connect the speakers to this unit.
This unit (rear)
• You can also connect up to 2 subwoofers (with built-in amplifier) to this unit. When using 2 subwoofers, configure the “SWFR Layout” setting (p.104) in the “Setup” menu after connecting the power cable to an AC wall outlet.
• To use an external power amplifier (Hi-Fi amplifier, etc.) to enhance speaker output, see “Connecting an external power amplifier” (p.27).
• When using only one surround back speaker, connect it to the SINGLE jack (L side).
En 19
FRONT
FRONT
(
SINGLE
)
CENTER
CENTER
SUR. BACKSURRUND
1
2
FRONT
Speaker connections
1
2 3 4 5 6 7 8 9
Connecting speaker cables
Speaker cables have two wires. One is for connecting the negative (-) terminal of the unit and the speaker, and the other is for the positive (+) terminal. If the wires are colored to prevent confusion, connect the black wire to the negative and the other wire to the positive.
a Remove approximately 10 mm of insulation from the ends of the speaker cable, and twist
the bare wires of the cable together firmly.
b Loosen the speaker terminal. c Insert the bare wires of the cable into the gap on the side (upper right or bottom left) of the
terminal.
d Tighten the terminal.
c
c
+
+ (red)
b
b
-
– (black)
Using a banana plug
a Tighten the speaker terminal. b Insert a banana plug into the end of the terminal.
Banana plug
b
b
aa
d
d
aa
+
Connecting the subwoofer
Use an audio pin cable to connect the subwoofer.
Audio pin cable
(
FRONT
)
(
REAR
)
SUBWOOFER
En 20
Speaker connections
1
2 3 4 5 6 7 8 9

Advanced speaker configuration

In addition to the basic speaker configuration (p.16), this unit also allows you to apply the following speaker configurations to enhance your system.
Using the four internal
amplifiers for front speakers to
have more high-quality sounds
Bi-amp connection Power-amp channel expansion Multi-zone configuration
(Example) (Example) (Example)
Bi-amp connection
Combining with an external
power amplifier (Hi-Fi
amplifier, etc.) to build an
extended system
External power amplifier
Using the excess internal
amplifiers for stereo speakers
in another room
Zone2
Main zone
En 21
Speaker connections
1
2 3 4 5 6 7 8 9
Available speaker configurations
Main zone
Output
channel
(max)
• When applying one of these configurations, you need to configure the “Power Amp Assign” setting (p.102) in the “Setup” menu.
• When applying a multi-zone configuration, you can select a zone (Zone2 or Zone3) to be assigned to the EXTRA SP1~2 jacks in “Power Amp Assign” (p.102) in the “Setup” menu. By default, Zone2 is assigned to the EXTRA SP1 jacks and Zone3 is assigned to the EXTRA SP2 jacks. The following explanation is based on the default zone assignments.
Bi-amp
7 { 7ch BI-AMP 22
9 Front +1 room 7ch +FRONT+1ZONE 23
7 Front +2 rooms 5ch +FRONT+2ZONE 23
7 +1 room 7ch +1ZONE 24
9 +1 room 9ch +1ZONE 24
7 +2 rooms 7ch +2ZONE 25
External power
amplifier
(required)
Multi-zone Power Amp Assign (p.102) Page
7ch BI-AMP
Bi-amp
Speaker Connect to
FRONT and EXTRA SP1 (bi-amp connection)
CENTER
SURROUND
SURROUND BACK
(not used)
(not used)
SUBWOOFER 1~2
En 22
Speaker connections
1
2 3 4 5 6 7 8 9
7ch +FRONT+1ZONE 5ch +FRONT+2ZONE
via external amp
Zone3
via external amp
Zone2
Main zone
Speaker Connect to
FRONT (PRE OUT) via external power amplifier
CENTER
SURROUND
SURROUND BACK
EXTRA SP1
(not used)
SUBWOOFER 1~2
Zone3 speakers EXTRA SP2
Main zone
Zone3
Speaker Connect to
FRONT (PRE OUT) via external power amplifier
CENTER
SURROUND
SURROUND BACK
(not used)
(not used)
SUBWOOFER 1~2
Zone2 speakers EXTRA SP1
Zone3 speakers EXTRA SP2
En 23
Speaker connections
1
2 3 4 5 6 7 8 9
7ch +1ZONE 9ch +1ZONE
Main zone
Speaker Connect to
FRONT
CENTER
SURROUND
SURROUND BACK
(not used)
(not used)
SUBWOOFER 1~2
Zone2 speakers EXTRA SP1
Zone2
Zone3
Main zone
Speaker Connect to
FRONT
CENTER
SURROUND
SURROUND BACK
EXTRA SP1
(not used)
SUBWOOFER 1~2
Zone3 speakers EXTRA SP2
• When Zone3 output is enabled (p.82), the surround back speakers in the main zone do not output sound.
En 24
Speaker connections
1
2 3 4 5 6 7 8 9
7ch +2ZONE
Main zone
Speaker Connect to
FRONT
CENTER
SURROUND
SURROUND BACK
(not used)
(not used)
SUBWOOFER 1~2
Zone2 speakers EXTRA SP1
Zone3 speakers EXTRA SP2
Zone2
Zone3
• When Zone3 output is enabled (p.82), the surround back speakers in the main zone do not output sound.
En 25
SPEAKERS
Speaker connections
1
Connecting front speakers that support bi-amp connections
2 3 4 5 6 7 8 9
When using front speakers that support bi-amp connections, connect them to the FRONT jacks and EXTRA SP1 jacks. To enable the bi-amp function, configure the “Power Amp Assign” setting (p.102) in the “Setup” menu after connecting the power cable to an AC wall outlet.
Connecting Zone2/3 speakers
When using Zone2/3 speakers, connect them to the EXTRA SP1~2 jacks. To utilize the EXTRA SP1~2 jacks for Zone2/3 speakers, configure the “Power Amp Assign” setting (p.102) in the “Setup” menu after connecting the power cable to an AC wall outlet.
This unit (rear)
SURROUND
R L
SURROUND BACK
R L
SINGLE
ZONE 2/ZONE 3/R.PRESENCE
R
CENTER FRONT
L
R
SPEAKER IMPEDANCE
L
ZONE 2/ZONE 3/F.PRESENCE/ BI–AMP
EXTRA SP1EXTRA SP2
R
L
This unit (rear)
SURROUND
R L
SURROUND BACK
R L
SINGLE
SPEAKERS
ZONE 2/ZONE 3/R.PRESENCE
R
CENTER FRONT
L
R
SPEAKER IMPEDANCE
L
ZONE 2/ZONE 3/F.PRESENCE/ BI–AMP
EXTRA SP1EXTRA SP2
R
L
Zone2 Zone3
Main zone
• You can select a zone (Zone2 or Zone3) to be assigned to the EXTRA SP1~2 jacks in “Power Amp Assign” (p.102) in the “Setup” menu. By default, Zone2 is assigned to the EXTRA SP1 jacks and Zone3 is assigned to the EXTRA SP2 jacks.
• You can also connect Zone2 and Zone3 speakers using an external amplifier (p.79).
Caution
• Before making bi-amp connections, remove any brackets or cables that connect a woofer with a tweeter. Refer to the instruction manual of the speakers for details. When not making bi-amp connections, make sure that the brackets or cables are connected before connecting the speaker cables.
En 26
O
3
R
Speaker connections
1
2 3 4 5 6 7 8 9
Connecting an external power amplifier
When using an external power amplifier to enhance speaker output, connect the input jacks of the power amplifier to the PRE OUT jacks of this unit. The same channel signals are output from the PRE OUT jacks as from their corresponding SPEAKERS terminals.
Caution
• To prevent the generation of loud noises or abnor mal sounds, make sure the followings before making connections.
- Remove the power cable of this unit and turn off the external power amplifier before connecting them.
- When using the PRE OUT jacks, do not connect speakers to the corresponding SPEAKERS
terminals.
- When using an external amplifier that does not have the volume control bypass, do not connect other
devices (except this unit) to the amplifier.
This unit (rear)
AV 1
2
(1 BD/DVD)
COMPONENT VIDEO
B PR
P
4
MULTI CH INPUT
SURROUND SUR. BACK
OUND
R L
L
HDMI
AV 2 AV 3 AV 4 AV 5 AV 6 AV 7
YPB PR
AV 3
AV 4
SURROUND BACK
CENTER
SUBWOOFER
C
MONITOR OUT/ZONE OUT
YPB PR
D
ZONE OUT
ZONE 2 ZONE 3FRONT
FRONT
SPEAKERS
ZONE 2/ZONE 3/R.PRESENCE
R
SINGLE
PRE OUT
SURROUND SUR. BACK
L
REMOTE
1
IN OUT2IN OUT
(SINGLE) (FRONT)
1
2
(REAR)
CENTER
SUBWOOFER
CENTER FRONT
R
SPEAKER IMPEDANCE
1 234
1 FRONT jacks
Output front channel sounds.
2 SURROUND jacks
Output surround channel sounds.
3 SUR. BACK jacks
Output surround back channel sounds. When using only one external amplifier for the surround back channel, connect it to the SINGLE jack (L side).
4 CENTER jack
Outputs center channel sounds.
TRIGGER
OUT
+12V 0.1A MAX.
L
1
2
R
RS-232C
ZONE 2/ZONE 3/F.PRESENCE/ BI–AMP
EXTRA SP1EXTRA SP2
AC IN
L
(Example) Connecting front speakers via an external power amplifier
PRE OUT (FRONT) jacks
I
AV 4 AV 5 AV 6 AV 7
P
B PR
(SINGLE) (FRONT)
PRE OUT
SURROUND SUR. BACK
L
REMOTE
1
IN OUT2IN OUT
1
2
(REAR)
CENTER
SUBWOOFER
CENTER FRONT
ONITOR OUT/ZONE OUT
FRONT
SPEAKERS
2/ZONE 3/R.PRESENCE
R
SPEAKER IMPEDANCE
TRIGGER
OUT
+12V 0.1A MAX.
L
1
2
FRONT
R
RS-232C
PR
ZONE 2/ZONE 3/F.PRESENCE/ BI–AMP
EXTRA SP1EXTRA SP2
SU
Main input jack
MAIN IN
L
R
AC IN
L
L
R
Amplifier with volume control bypass (A-S2000, etc.)
This unit (rear)
About external power amplifiers
We recommend using power amplifiers that meet the following conditions.
- With unbalanced inputs
- With volume control bypass (or without volume control circuit)
- Output power: 100 W (8Ω) or more
• When using an external amplifier that does no have the volume control bypass, turn up the volume of the external amplifier enough and fix it.
En 27

Input/output jacks and cables

COMPONEN
AV 1
A
Video/audio jacks
HDMI jacks
Transmit digital video and digital sound through a single jack. Use an HDMI cable.
AV 1
• Use a 19-pin HDMI cable with the HDMI logo. We recommend using a cable less than 5.0 m long to prevent signal quality degradation.
• To connect a device that has a DVI jack, an HDMI/DVI-D cable is required.
• The HDMI jacks of this unit support the HDMI Control, Audio Return Channel (ARC), and 3D video transmission (through output) features.
HDMI cable
Video jacks
COMPONENT VIDEO jacks
Transmit video signals separated into three components: luminance (Y), chrominance blue (PB), and chrominance red (PR). Use a component video cable with three plugs.
Component video cable
S VIDEO jack
Transmits S-video signals that include luminance (Y) and chrominance (C) components. Use an S-video cable.
S-video cable
VIDEO jacks
Transmit analog video signals. Use a video pin cable.
AV 1
Video pin cable
Audio jacks
OPTICAL jacks
Transmit digital audio signals. Use a digital optical cable. Remove the tip protector (if available) before using the cable.
Digital Optical cable
COAXIAL jacks
Transmit digital audio signals. Use a digital coaxial cable.
Digital coaxial cable
AUDIO jacks
Transmit analog stereo audio signals. Use a stereo pin cable.
Stereo pin cable
En 28
TV connection
1 2
3 4 5 6 7 8 9
2 Connecting a TV
Connect a TV to this unit so that videos input to this unit can be output to the TV. You can also enjoy playback of TV audio on this unit. The connection method varies depending on functions and video input jacks available on your TV. Refer to the instruction manual of the TV and choose a connection method.
Does your TV support
Audio Return Channel (ARC)?
Yes
Connection method 1 (p.29)
No
Does your TV support
HDMI Control?
Yes
Connection method 2 (p.31)
No
Does your TV have an
HDMI input jack?
Yes
Connection method 3 (p.32)
No
Connection method 4 (p.33)
About HDMI Control
HDMI Control allows you to operate external devices via HDMI. If you connect a TV that supports HDMI Control to this unit with an HDMI cable, you can control this unit (power, volume, etc.) in conjunction with TV remote control operations. You can also control playback devices (HDMI Control-compatible BD/DVD player, etc.) connected to this unit with an HDMI cable. For details, see “HDMI Control” (p.142).
About Audio Return Channel (ARC)
ARC allows audio signals to travel both ways under HDMI Control. So if you connect a TV that supports HDMI Control and ARC to this unit with a single HDMI cable, you can output video/audio to the TV or input TV audio to this unit.
Connection method 1 (HDMI Control/ARC-compatible
TV)
Connect the TV to this unit with an HDMI cable.
• The following explanation is based on the assumption that you have not changed the “HDMI” parameters (p.109) in the “Setup” menu.
• HDMI Control is available only on the HDMI OUT 1 jack.
HDMI OUT 1 jack
HDMI OUT
12
ARC
1 2
ARC
MONITOR OUT/
ZONE OUT
(3 CD)
6
COAXIAL
HDMI OUT
AV 1
A
AV 2
B
R L
HDMI
YP
AUDIO 4AUDIO 3AUDIO 2
SURROUND
AV 1
(1
B
FRONT
HDMI input
(ARC-compatible)
HDMI
HDMI
TV
This unit (rear)
NETWORK
DOCK
AV 1
AV 3 AV 4AV 2
(1 BD/DVD)
PHONO
GND
L
R
1
COAXIAL
• If you make an HDMI connection between your TV and this unit, any videos input to this unit can be output to the TV no matter how you connect video devices to this unit. For details, see “Video signal flow” (p.141).
AV OUT
AUDIO 1
(2 TV)
2
ANTENNA
(4 RADIO)
5
OPTICAL
OPTICAL4OPTICAL3COAXIAL
AM
FM
75Ω
• You can connect another TV or a projector by using the HDMI OUT 2 jack (p.34).
En 29
1 2
TV connection
3 4 5 6 7 8 9
Necessary settings
To use HDMI Control and ARC, you need to configure the following settings. For details on settings and operations of your TV, refer to the instruction manual of the TV.
After connecting external devices (TV, playback devices, etc.) and
1
power cable of this unit, turn on this unit, TV and playback devices.
Configure the settings of this unit.
2
a Check that ARC is enabled on the TV.
b Switch the TV input to display the video from this unit.
c Press ON SCREEN.
ON SCREEN
RETURN DISPLAY
d Use the cursor keys to select “Setup” and press ENTER.
ENTER
OPTION
ON SCREEN Cursor keys ENTER
Configure the settings for HDMI Control.
3
a Enable HDMI Control on the TV and playback devices (HDMI Control-compatible BD/
DVD player, etc).
b Turn off the main power of the TV and then turn off this unit and playback devices.
c Turn on this unit and playback devices and then turn on the main power of the TV.
d Switch the TV input to display the video from this unit.
e Check the followings.
On this unit: The input to which the playback device is connected is selected. If not, select the input source manually.
On the TV: The video from the playback device is displayed.
f Check that this unit is properly synchronized with the TV by turning off the TV or
adjusting the TV volume with the TV remote control.
Now the necessary settings are complete.
If you select a TV program with the TV remote control, the input source of this unit will be automatically switched to “AUDIO1” and the TV audio will be played back on this unit.
If TV audio cannot be heard, check that “ARC” (p.109) in the “Setup” menu is set to “On”.
• If HDMI Control does not work properly, try turning off and on (or unplugging and re-plugging) the devices. It may solve the problem.
• If any audio interruption happens while using ARC, set “ARC” (p.109) in the “Setup” menu to “Off” and use an audio cable (digital optical or stereo pin cable) to input TV audio to this unit (p.31).
e Use the cursor keys ( / ) to select “HDMI”.
f Use the cursor keys ( / ) to select “HDMI Control” and press ENTER.
g Use the cursor keys to select “On”. h Press ON SCREEN.
• “AUDIO1” is set as TV audio input at the factory. If you have connected any external device to the AUDIO1 jacks, use “TV Audio Input” (p.109) in the “Setup” menu to change the TV audio input assignment. To use the SCENE function (p.53), you also need to change the input assignment for SCENE(TV).
En 30
Loading...
+ 119 hidden pages