Yamaha RX-V1600 User Manual

RX-V1600

AV Receiver

Ampli-tuner audio-vidéo

OWNER'S MANUAL

MODE D'EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: – Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords. 10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is faulty.

18 Before moving this unit, press MASTER ON/OFF to release it

outward to the OFF position to turn off this unit, the main room, Zone 2 and Zone 3 and then disconnect the AC power plug from the AC wall outlet.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are:

Asia model ................................ AC 220/230–240 V, 50/60 Hz

General model .............AC 110/120/220/230–240 V, 50/60 Hz

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by MASTER ON/OFF. In this state, this unit is designed to consume a very small quantity of power.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below.

Note

The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.

■ Special Instructions for U.K. Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug.

CONTENTS

INTRODUCTION

FEATURES............................................................. 2

GETTING STARTED............................................ 3

Supplied accessories .................................................. 3

Installing batteries in the remote controls.................. 4

Handling the remote control ...................................... 5

Opening and closing the front panel door.................. 5

CONTROLS AND FUNCTIONS ......................... 6

Front panel ................................................................. 6

Remote control........................................................... 8

Zone 2/Zone 3 remote control ................................. 10

Front panel display .................................................. 11

Rear panel ................................................................ 13

PREPARATION

CONNECTIONS .................................................. 14

Before connecting speakers ..................................... 14

Connecting speakers ................................................ 15

Using bi-wire and bi-AMP connections .................. 19

Information on cables and jacks

used for connections ............................................ 20

Connecting HDMI components ............................... 23

Connecting video components................................. 24

Connecting audio components................................. 27

Connecting the antennas .......................................... 29

Connecting the power cable..................................... 30

Turning on and off this unit ..................................... 30

Setting the speaker impedance................................. 31

AUTO SETUP....................................................... 32

Introduction.............................................................. 32

Optimizer microphone setup.................................... 32

Using AUTO SETUP .............................................. 33

BASIC OPERATION

PLAYBACK.......................................................... 36

Basic operations....................................................... 36

Additional operations............................................... 38

RECORDING ....................................................... 45

FM/AM TUNING ................................................. 46

Automatic tuning ..................................................... 46

Manual tuning.......................................................... 47

Automatic preset tuning........................................... 47

Manual preset tuning ............................................... 49

Selecting preset stations........................................... 50

Exchanging preset stations ...................................... 51

Receiving Radio Data System stations ....................52

Changing the Radio Data System mode .................. 52

PTY SEEK function ................................................ 53

EON function........................................................... 54

SOUND FIELD PROGRAMS

EDITING SOUND FIELD PARAMETERS ......55

What is a sound field? ............................................. 55

Changing parameter settings ................................... 55

SOUND FIELD PROGRAM

DESCRIPTIONS...............................................57

For movie/video sources.......................................... 57

For music sources .................................................... 59

SOUND FIELD PARAMETER

DESCRIPTIONS...............................................60

SOUND FIELD PROGRAM

SPEAKER LAYOUTS......................................64

ADVANCED OPERATION

MANUAL SETUP.................................................68

Using MANUAL SETUP ........................................ 70

Using BASIC MENU .............................................. 71

Using SOUND MENU ............................................ 74

Using INPUT MENU .............................................. 76

Using OPTION MENU ........................................... 78

ADVANCED OPERATIONS ..............................82

Selecting the OSD mode.......................................... 82

Adjusting speaker levels .......................................... 82

ADVANCED SETUP ............................................83

Using ADVANCED SETUP ................................... 83

REMOTE CONTROL FEATURES ...................85

Control area ............................................................. 85

Controlling each component.................................... 86

Setting remote control codes ................................... 87

Using LEARN ......................................................... 89

Using RE-NAME .................................................... 91

Using MACRO ........................................................ 92

Using CLEAR.......................................................... 94

ZONE 2/ZONE 3 ...................................................97

Connecting the Zone 2 and

Zone 3 components ............................................. 97

Selecting Zone 2 or Zone 3...................................... 98

Controlling Zone 2 and Zone 3................................ 99

Using the control mode of

Zone 2 and Zone 3............................................. 100

HDMI ...................................................................101

What is HDMI? ..................................................... 101

Setting the HDMI parameters................................ 102

Basic HDMI operations ......................................... 102

ADDITIONAL INFORMATION

TROUBLESHOOTING .....................................103

GLOSSARY.........................................................110

Audio information ................................................. 110

Video information.................................................. 112

Sound field program information .......................... 112

Parametric equalizer information .......................... 113

SPECIFICATIONS.............................................114

PREPARATIONINTRODUCTION

OPERATION

BASIC

SOUND FIELD

PROGRAMS

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

English

FEATURES

Built-in 7-channel power amplifier

◆ Minimum RMS Output Power (0.04% THD, 20 Hz to 20 kHz, 8 Ω) Front: 120 W + 120 W Center: 120 W Surround: 120 W + 120 W Surround Back: 120 W + 120 W

Sound field features

◆ Proprietary YAMAHA technology for the creation of sound fields

◆ THX Select2

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1,

DTS Neo:6 decoder, DTS 96/24

◆ Dolby Pro Logic/Dolby Pro Logic x decoder

◆ Virtual CINEMA DSP

◆ SILENT CINEMA

™

Sophisticated AM/FM tuner

◆ 40-station random access preset tuning

◆ Automatic preset tuning

◆ Preset station shifting capability (preset editing)

Radio Data System (U.K. and Europe models only)

◆ Radio Data System tuning capability

HDMI (High-Definition Multimedia Interface)

◆ HDMI interface for standard, enhanced or high-definition video as well as multi-channel digital audio

◆ Analog video to HDMI digital video up-conversion (composite video ↔ S-video ↔ component video → HDMI digital video) capability for monitor out

Other features

◆ YPAO (YAMAHA Parametric Room Acoustic Optimizer) for automatic speaker setup

◆ 192-kHz/24-bit D/A converter

◆ OSD (on-screen display) menus that allow you to

optimize this unit to suit your individual audio/video system

◆ 6 or 8-channel additional input jacks for discrete multi-channel input

◆ Short message function

◆ PURE DIRECT for pure fidelity sound with analog and

PCM sources

◆ S-video input/output capability

◆ Component video input/output capability

◆ Analog video I/P conversion from 576i to 576p

◆ Optical and coaxial digital audio signal jacks

◆ Sleep timer

◆ Cinema and music night listening mode

◆ Remote control with preset remote control codes and

learning/macro capability

◆ Zone 2/Zone 3 custom installation facility

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and product, the product has priority.

Manufactured under license from Dolby Laboratories. “Dolby”, “Surround EX”, and the double-D symbol are trademarks of Dolby Laboratories.

“DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks of Digital Theater Systems, Inc.

“HDMI”, the “HDMI” logo and “High-Definition Multimedia Interface” are trademarks or registered trademarks of HDMI Licensing LLC.

“SILENT CINEMA” is a trademark of YAMAHA CORPORATION.

GETTING STARTED

Supplied accessories

Please check that you received all of the following parts.

Remote control

POWER POWER

PHONO TUNER CD

V-AUX

DTV DVR/VCR2VCR 1 DVD

TV VOL

–

TV MUTE TV INPUT

LEVEL

TITLE

BAND

A/B/C/D/E

RETURN

STEREO

THX

5678

FREQ/TEXT EON MODE PTY SEEK START

REC

DISC SKIP

POWER

STANDBY

AVTV

SLEEP

AUDIO SEL

MULTI CH IN

CBL/SAT MD/TAPE

SELECT

VOLUME

–

MUTE

PRESET

SET MENU

PURE DIRECT

SRCH MODE

NIGHT

ENTER

ON SCREEN

STRAIGHT

DISPLAY

EFFECT

MUSIC ENTERTAIN MOVIE

3421

STANDARD SELECT EXTD SUR.

2 B

SPEAKERSMEMORY

+10

CLEAR

LEARN

MACROONOFF

CD-R

AUDIO

ENT.

RE–NAME

SOURCE

Zone 2/Zone 3

remote control

AMP

TUNER1CD2CD-R

DTV4CBL/SAT5MD/TAPE

DVD

VCR17DVR/VCR2

8 9

PRESET

VOLUME

–

A/B/C/D/E

ID2ID1

INTRODUCTION

POWER

STANDBY

PHONO

ENT

V-AUX

–

MUTE

ZONE 3ZONE 2

Batteries (x6)

(AAA, R03)

Power cable

AM loop antenna

Speaker terminal

wrench

Indoor FM antenna (U.S.A., Canada, Asia, General, China and Korea models)

Optimizer microphone

Indoor FM antenna (Australia, U.K. and Europe models)

75-ohm/300-ohm antenna adapter (U.K. model only)

English

GETTING STARTED

Installing batteries in the remote controls

Notes

• Change all of the batteries if you notice conditions such as the operation range of the remote control decreases, the indicator does not flash, or its light or display window become dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color.

• If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

• Do not throw away batteries with general house waste; dispose of them correctly in accordance with your local regulations.

■ Installing batteries

1 Press the part and slide the battery

compartment cover off.

2 Insert four supplied batteries

(AAA, R03) according to the polarity markings on the inside of the battery compartment.

3 Slide the cover back until it snaps into place.

■ Zone 2/Zone 3 remote control

1 Press the part and slide the battery

compartment cover off.

2 Insert two supplied batteries (AAA, R03)

according to the polarity markings (+ and –) on the inside of the battery compartment.

3 Slide the cover back until it snaps into place.

If the remote control is without batteries for more than 2 minutes, or if exhausted batteries remain in the remote control, the contents of the memory may be cleared. When the memory is cleared, insert new batteries, set up the remote control code and program any acquired functions that may have been cleared.

Handling the remote control

GETTING STARTED

The remote control transmits a directional infrared ray. Be sure to aim the remote control directly at the remote control sensor on the main unit during operation.

PURE DIRECT

MULTI CH

AUDIO

INPUT

SELECT

INPUTMAIN ZONE

ON/OFF

MASTER

ON OFF

Approximately 6 m

A/B/C/D/E

SPEAKERS

YPAO

OPTIMIZER

MIC

PRESET/ TUNING

MULTI ZONE

SILENT CINEMA S VIDEO VIDEO L

PHONES

PRESET/

TUNING

MEMORY

FM/AM

TUNING

MODE

MAN'L/AUTO FM

EDIT

AUTO/MAN'L EFFECT

ZONE ON/OFF

ZONE CONTROL

ZONE 2

ZONE 3

AUDIO R OPTICAL

VIDEO/AUX

STRAIGHT

PROGRAM

POWER POWER POWER

PHONO TUNER CD

V-AUX

CBL/SAT MD/TAPE

DTV DVR/VCR2VCR 1 DVD

TV VOL

–

TV MUTE TV INPUT

LEVEL

TITLE

BAND

A/B/C/D/E

RETURN

STEREO

MUSIC ENTERTAIN MOVIE

THX

STANDARDSELECT EXTD SUR.

5678

FREQ/TEXT EON MODEPTY SEEK START

REC

DISC SKIP

MACROONOFF

VOLUME

TONE

CONTROL

30 30

SYSTEM

STANDBY

AVTV

SLEEP

AUDIO SEL

MULTI CH IN

CD-R

SELECT

AMP

SOURCE

VOL

–

MUTE

PRESET

SET MENU

PURE DIRECT

NIGHT

ENTER

AUDIO

ON SCREEN

STRAIGHT

DISPLAY

EFFECT

3421

SPEAKERS

ENT.

+10

CLEAR

LEARN

RE–NAME

Notes

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types of conditions: – places of high humidity, such as near a bath – places of high temperatures, such as near a heater or stove – extremely low temperatures – dusty places

INTRODUCTION

Opening and closing the front panel door

When you want to use the controls behind the front panel door, open the door by gently pressing on the lower part of the panel. Keep the door closed when not using these controls.

To open, press gently on the lower part of the panel.

English

CONTROLS AND FUNCTIONS

Front panel

CONTROLS AND FUNCTIONS

21 3 45 6 7 8 90AB C E F

MULTI CH

ON/OFF

MASTER

ON OFF

AUDIO

INPUT

SELECT

INPUTMAIN ZONE

PRESET/

TUNING

A/B/C/D/E

SPEAKERS

YPAO

SILENT CINEMA S VIDEO VIDEO L

OPTIMIZER

PHONES

MIC

ILMKJHG

1 MASTER ON/OFF

Press inward to the ON position.

• Turns on this unit.

• Turns on the main room.

• Sets Zone 2 and Zone 3 to the standby mode. Press again to release it outward to the OFF position.

• Turns off this unit.

• Turns off the main room, Zone 2 and Zone 3. See page 30 for details.

2 MAIN ZONE ON/OFF

Turns on this unit only or sets it to the standby mode.

In the standby mode, this unit consumes a small quantity of power.

Notes

• When you turn on this unit, there will be a 6 to 7 second delay before this unit can reproduce sound.

• This button is operational only when MASTER ON/OFF is pressed inward to the ON position.

3 INPUT selector

Selects the desired input source.

PURE DIRECT

VOLUME

STRAIGHT

PROGRAM

TONE

CONTROL

MULTI ZONE

PRESET/

TUNING

EDIT

FM/AM

ZONE 2

VIDEO/AUX

MEMORY

MAN'L/AUTO FM

ZONE ON/OFF

ZONE 3

AUDIO R OPTICAL

TUNING MODE

AUTO/MAN'L EFFECT

ZONE CONTROL

(General model)

4 AUDIO SELECT

Toggles the priority for the type of audio input jack between AUTO, HDMI, COAX/OPT and ANALOG when one component is connected to two or more input jacks on the rear panel (see page 43).

5 MULTI CH INPUT

Selects the input source connected to the MULTI CH INPUT jacks. When selected, the MULTI CH INPUT source takes priority over the input source selected with the INPUT selector (or the input selector buttons on the remote control).

6 A/B/C/D/E

Selects one of the 5 preset station groups (A to E) when TUNER is selected as the input source (see page 50).

7 PRESET/TUNING l / h

Selects the preset station number (1 to 8) when TUNER is selected as the input source and the colon (:) is displayed next to the band indication in the front panel display. Selects the tuning frequency when TUNER is selected as the input source and the colon (:) is not displayed in the front panel display. See pages 46 to 51 for details.

CONTROLS AND FUNCTIONS

8 Front panel display

Shows information about the operational status of this unit.

9 PRESET/TUNING (EDIT)

Switches the function of PRESET/TUNING l / h between selecting preset station numbers and tuning when TUNER is selected as the input source (see pages 46 to

51).

0 FM/AM

Switches the reception band (FM or AM) when TUNER is selected as the input source (see page 46).

Note

The frequency of the previously received station is automatically recalled.

A MEMORY (MAN’L/AUTO FM)

Stores a station in the memory when TUNER is selected as the input source. Hold down for more than 3 seconds to start automatic preset tuning (see page 47).

B TUNING MODE (AUTO/MAN’L), DISPLAY

Switches the tuning mode between automatic (the AUTO indicator is turned on) and manual (the AUTO indicator is turned off) when TUNER is selected as the input source.

C STRAIGHT (EFFECT)

Turns the sound field programs on or off. When STRAIGHT is selected, 2-channel or multi-channel input signals are output directly from the respective speakers without effect processing.

D Remote control sensor

Receives infrared signals from the remote control.

E TONE CONTROL

Use to adjust the balance of bass and treble for the front left and right and center channels (see page 38).

F PURE DIRECT

Turns on or off the PURE DIRECT mode (see page 41).

Note

The indicator around the button lights up when the unit is in the PURE DIRECT mode.

G OPTIMIZER MIC jack

Use to connect the supplied optimizer microphone to run AUTO SETUP (see page 32).

H SPEAKERS A/B

Turn on or off the set of front speakers connected to the SPEAKERS A and/or B terminals on the rear panel each time the corresponding button is pressed.

I PHONES (SILENT CINEMA) jack

Outputs audio signals for private listening with headphones.

INTRODUCTION

Notes

• When you connect headphones, no signals are output at the PRE OUT jacks or to the speakers.

• All Dolby Digital and DTS audio signals are mixed down to 2channel stereo (front left and right channels).

J VIDEO AUX jacks

Input audio and video signals from an external source such as a game console. To reproduce source signals at these jacks, select V-AUX as the input source.

K MULTI ZONE buttons

ZONE 2 ON/OFF

Turns on Zone 2 only or sets it to the standby mode. See page 30 for details.

Note

This button is operational only when MASTER ON/OFF is pressed inward to the ON position.

ZONE 3 ON/OFF

Turns on Zone 3 only or sets it to the standby mode. See page 30 for details.

Note

This button is operational only when MASTER ON/OFF is pressed inward to the ON position.

ZONE CONTROL

Switches the zone you want to control between the main unit, Zone 2 and Zone 3 (see page 99). After you press ZONE CONTROL, the indicator for the currently selected zone flashes in the front panel display for approximately 5 seconds. While the indicator is flashing, perform the desired operation.

L PROGRAM selector

Use to select sound field programs or adjust the balance of bass and treble in conjunction with TONE CONTROL.

M VOLUME

Controls the volume level of all audio channels.

Note

This does not affect the OUT (REC) level.

English

CONTROLS AND FUNCTIONS

Remote control

This section describes the function of each control on the remote control used to control this unit. Set AMP/ SOURCE/TV to AMP to operate this unit. To operate other components, see “REMOTE CONTROL FEATURES” on page 85.

POWER POWER

AVTV

POWER

STANDBY

AUDIO SEL

SLEEP

B C D

PHONO TUNER CD

MULTI CH IN

V-AUX

CBL/SAT MD/TAPE

DTV DVR/VCR2VCR 1 DVD

TV VOL

–

TV MUTE TV INPUT

PRESET

LEVEL

TITLE

BAND

ENTER

A/B/C/D/E

RETURN

STEREO

MUSIC ENTERTAIN MOVIE

THX

STANDARD SELECT EXTD SUR.

5678

2 B

FREQ/TEXT EON MODE PTY SEEK START

FREQ/TEXT

EON STARTMODE PTY SEEK

VOLUME

SET MENU

ON SCREEN

DISPLAY

3421

+10

–

MUTE

SPEAKERSMEMORY

CD-R

SELECT

AMP

SOURCE

PURE DIRECT

NIGHT

AUDIO

STRAIGHT

EFFECT

ENT.

J K

L M

REC

DISC SKIP

MACROONOFF

LEARN

CLEAR

RE–NAME

P Q R

1 Infrared window

Outputs infrared control signals. Aim this window at the component you want to operate.

2 Transmission indicator

Flashes while the remote control is sending infrared signals.

3 Input selector buttons

Select the input source and change the control area. Set AMP/SOURCE/TV to SOURCE and then press TUNER to select TUNER as the input source.

4 Display window

Shows the name of the selected input source that you can control.

5 LEVEL, BAND

Selects the speaker you want to adjust the speaker output level for when AMP/SOURCE/TV is set to AMP (see pages 82). Switches the reception band between FM and AM when AMP/SOURCE/TV is set to SOURCE and TUNER is selected as the input source.

6 Cursor buttons k / n / l / h, ENTER

Selects and adjusts the DSP program parameters or OSD menu items when AMP/SOURCE/TV is set to AMP. Press l / h to select a preset station group (A to E) and k / n to select a preset station number (1 to 8) when AMP/SOURCE/TV is set to SOURCE and TUNER is selected as the input source.

7 RETURN

Returns to the upper or the previous directory in the OSD menu.

8 Sound field program / numeric buttons

Select sound field programs when AMP/SOURCE/TV is set to AMP. Use SELECT to play back 2-channel sources in the multichannel format (see page 40). Use EXTD SUR. to switch between 5.1 and 6.1/7.1 channel playback of multi-channel software (see page 39). Use numbers 1 to 8 to select preset stations when AMP/ SOURCE/TV is set to SOURCE and TUNER is selected as the input source.

9 MACRO ON/OFF

Turns on or off the macro function (see page 93).

(U.K. and Europe models)

0 MACRO

Programs a series of operations to be controlled with a single button (see page 92).

CONTROLS AND FUNCTIONS

A STANDBY

Sets this unit, Zone 2 and Zone 3 to the standby mode (see page 30).

Note

This button is operational only when MASTER ON/OFF on the front panel is pressed inward to the ON position.

B POWER

Turns on this unit, Zone 2 and Zone 3 (see page 30).

Note

This button is operational only when MASTER ON/OFF on the front panel is pressed inward to the ON position.

C AUDIO SEL

Toggles the priority for the type of audio input jack between AUTO, HDMI, COAX/OPT and ANALOG when one component is connected to two or more input jacks on the rear panel (see page 43).

D SLEEP

Sets the sleep timer.

E MULTI CH IN

Selects MULTI CH INPUT when using an external decoder, etc.

F SELECT k / n

Selects another input source that you can control independently of the input source selected with the input selector buttons.

G VOLUME +/–

Increases or decreases the volume level.

H AMP/SOURCE/TV

Selects the component you want to control with the remote control.

AMP

Set to this position to operate this unit.

SOURCE

Set to this position to operate the component selected with an input selector button.

Set to this position to operate the television assigned to either DTV or PHONO.

Note

If televisions are assigned to both DTV and PHONO, the one assigned to DTV takes priority and gets operated when AMP/ SOURCE/TV is set to TV.

To set the remote control codes for other components, see page 87.

I MUTE

Mutes the sound. Press again to restore the audio output to the previous volume level.

J PURE DIRECT

Turns on or off the PURE DIRECT mode (see page 41).

K SET MENU

Enters or exits the SET MENU mode.

L NIGHT

Turns on or off the night listening modes (see page 41).

M ON SCREEN

Selects the display mode of the on-screen display (OSD) that appears on your monitor (see page 82).

N STRAIGHT (EFFECT)

Switches the sound field programs off or on. When STRAIGHT is selected, 2-channel or multi-channel input signals are output directly from their respective speakers without effect processing.

O SPEAKERS A/B

Turns on or off the set of front speakers connected to the SPEAKERS A and/or B terminals on the rear panel each time the corresponding button is pressed.

P RE-NAME

Changes the name of the input source in the display window (see page 91).

Q CLEAR

Clears remote control codes or functions acquired from the learn, macro and rename features (see page 94).

R LEARN

Programs remote control codes or functions from other remote controls (see page 89).

S Radio Data System tuning buttons

(U.K. and Europe models only)

These buttons are operational only when TUNER is selected as the input source.

FREQ/TEXT

Switches the Radio Data System display between the PS mode, PTY mode, RT mode, CT mode (if the station offers the corresponding data services) and the frequency display (see page 52).

PTY SEEK MODE

Sets this unit to the PTY SEEK mode (see page 53).

PTY SEEK START

Starts searching for a station after the desired program type has been selected in the PTY SEEK mode (see page 53).

EON

Selects a radio program type (NEWS, INFO, AFFAIRS, SPORTS) tune in automatically (see page 54).

INTRODUCTION

English

CONTROLS AND FUNCTIONS

Zone 2/Zone 3 remote control

This section describes the function of each control on the Zone 2/Zone 3 remote control used to control Zone 2 or Zone 3.

POWER

TUNER1CD2CD-R

DTV4CBL/SAT5MD/TAPE

VCR17DVR/VCR2

8 9

PRESET

–

3 8

A/B/C/D/E

ID2ID1

(U.K. and Europe models)

DVD

VOLUME

–

MUTE

STANDBY

PHONO

ENT

V-AU X

ZONE 3ZONE 2

1 Input selector buttons

Select the desired input source of Zone 2 or Zone 3 and change the control area.

2 PRESET +/–

Selects the preset station number (1 to 8) when TUNER is selected as the input source or Zone 2 or Zone 3.

3 A/B/C/D/E

Selects the preset station group (A to E) when TUNER is selected as the input source or Zone 2 or Zone 3.

4 ID1/ID2 switch

Switches the remote control ID between ID1 and ID2 (see page 88).

5 POWER

Turns on Zone 2 or Zone 3.

Note

This button is operational only when MASTER ON/OFF on the front panel is pressed inward to the ON position.

6 STANDBY

Sets Zone 2 or Zone 3 to the standby mode.

Note

This button is operational only when MASTER ON/OFF on the front panel is pressed inward to the ON position.

7 VOLUME +/–

Increases or decreases the volume level or Zone 2 or Zone 3.

8 MUTE

Mutes the sound of Zone 2 or Zone 3. Press again to restore the audio output to the previous volume level.

9 ZONE 2/ZONE 3 switch

Switches between the operation mode of Zone 2 and that of Zone 3.

Front panel display

CONTROLS AND FUNCTIONS

Note

The XM indicator is only applicable to the U.S.A. model.

123 4 5 6 7 890A

V-A UX

DIGITAL

YPAO

A B

SILENT CINEMA

HiFi DSP

VIRTUAL

PL x EX

DISCRETE

MATRIX

96 24

1 YPAO indicator

Lights up when the AUTO SETUP procedure is in progress and when the AUTO SETUP speaker settings are used without any modifications.

2 HDMI indicator

Lights up when HDMI components are assigned to HDMI IN 1 and HDMI IN 2 jacks and they are recognized by this unit (see page 76). Turns off when no HDMI component is assigned to the either HDMI IN 1 or HDMI IN 2 jack or when no HDMI component is recognized by this unit although they are assigned to the HDMI IN jacks (see page 76).

DSD

PCM

VCR 1

DTV DVD CD-R CD

MD/TAPECBL/SATDVR/VCR 2

A MEMORY indicator

Flashes to indicate that a station can be stored.

B Headphones indicator

Lights up when headphones are connected.

C SILENT CINEMA indicator

Lights up when headphones are connected and a sound field program is selected (see page 38).

D SP A B indicators

Light up according to the set of front speakers selected. Both indicators light up when both sets of front speakers are selected or when bi-wiring.

STEREO AUTO

ZONE2 ZONE3

NIGHT SLEEP

PTY

TUNED

MEMORY

PTY

RT CT

EON

HOLD

VOLUME

96/24

LL C R

LFE

SL SB SR

MUTE

TUNERPHONO

QOPNMLKJHGFEDCB

(U.K. and Europe models)

See page 101 for details.

3 CINEMA DSP indicator

Lights up when you select a CINEMA DSP sound field

E VIRTUAL indicator

Lights up when Virtual CINEMA DSP is active (see page 43).

program.

4 Decoder indicators

When any of the decoders of this unit operate, the respective indicator lights up.

5 Input source indicators

Light up when the corresponding input source is selected.

6 VOLUME level indicator

Indicates the volume level.

7 MUTE indicator

Flashes while the MUTE function is on.

8 AUTO indicator

Lights up when this unit is in the automatic tuning mode.

9 STEREO indicator

Lights up when this unit is receiving a stereo signal for an FM stereo broadcast while the AUTO indicator is lit.

0 TUNED indicator

Lights up when this unit is tuned into a station.

F Sound field indicators

Light up to indicate the active DSP sound fields.

Presence DSP sound field

Listening position

Left surround DSP sound field

Surround/surround back DSP sound field

Right surround DSP sound field

G HiFi DSP indicator

Lights up when you select a HiFi DSP sound field program.

H PCM indicator

Lights up when this unit is reproducing PCM (pulse code modulation) digital audio signals.

I DSD indicator

Lights up when this unit is reproducing DSD (direct stream digital) digital audio signals.

J Multi-information display

Shows the name of the current sound field program and other information when adjusting or changing settings.

INTRODUCTION

English

CONTROLS AND FUNCTIONS

K 96/24 indicator

Lights up when a DTS 96/24 signal is input to this unit.

L LFE indicator

Lights up when the input signal contains an LFE signal.

M Input channel and speaker indicators

Input channel indicators

Indicate the channel components of the current digital input signal.

LL C R SL SB SR

Presence and surround back speaker indicators

Light up according to the number of presence and surround back speakers set for PRESENCE SP (see page 72) and SB L/R SP (see page 72) in MANUAL SETUP when TEST TONE in MANUAL SETUP is set to ON (see page 74).

You can make settings for the presence and surround back speakers automatically by running AUTO SETUP (see page 32) or manually by adjusting settings for PRESENCE SP (see page 72) and SB L/R SP (see page 72) in MANUAL SETUP.

N ZONE 2/ZONE 3 indicators

Light up when Zone 2 or Zone 3 is turned on.

O NIGHT indicator

Lights up when you select a night listening mode.

P SLEEP indicator

Lights up while the sleep timer is on.

Q Radio Data System indicators

(U.K. and Europe models only)

The name of the Radio Data System data offered by the currently received Radio Data System station lights up.

EON

Lights up when a Radio Data System station that offers the EON data service is being received.

PTY HOLD

Lights up while searching for stations in the PTY SEEK mode.

Rear panel

CONTROLS AND FUNCTIONS

CD DVD

DVD

DTV

CBL/SAT

MD/TAPE

CD-R

DIGITAL OUTOUT

DIGITAL INPUT

OPTICAL

RS-232C

HDMI

COAXIAL

DVR/ VCR 2

IN 1

IN 2

OUT

DVD

DTV

CBL/

SAT

COMPONENT VIDEO

PBY

MONITOR OUT

S VIDEO

MONITOR OUT

AUDIOVIDEO

VIDEO

DVD

DTV

CBL/ SAT

VCR 1

OUT

DVR/VCR 2

OUT

ZONE

OUTPUT

(PLAY)

MD/TAPE

OUT

(REC) (PLAY)

CD-R

OUT

(REC)

PHONO

FRONT(6CH)/SB(8CH)

SURROUND

MULTI CH INPUT

AUDIO

CENTERSUBWOOFER

REMOTE

OUT

FRONT

SURROUND

SUBWOOFER

SURROUND BACK/PRESENCE

1 DIGITAL OUTPUT jacks

See pages 24, 25 and 27 for connection information.

2 DIGITAL INPUT jacks

See pages 24, 25 and 27 for details.

3 Video component jacks

See pages 24 and 25 for connection information.

4 Audio component jacks

See pages 24, 25 and 27 for connection information.

5 CONTROL OUT jacks

These are control expansion terminals for factory use only.

6 WRENCH HOLDER

Use to hook the supplied speaker terminal wrench when not in use (see page 16).

7 Antenna terminals

See page 29 for connection information.

8 VOLTAGE SELECTOR

(Asia and General models only)

See page 30 for detailed information.

812 3 4 56 7 90

CONTROL OUT

+12V 15mA MAX.

GND

PRE OUT

WRENCH HOLDER

CENTER

SINGLE

(SB)

TUNER

FM ANT

75Ω

UNBAL.

SPEAKERS

–

FRONT

–

SURROUND/ZONE 2(3)

–

SURROUND BACK

AM ANT

GND

–

CENTER

–

SINGLE

++––

–

SPEAKER IMPEDANCE

–

PRESENCE/ZONE 2(3)

VOLTAGE

SELECTOR

AC OUTLETS

SWITCHED

50W MAX.TOTAL

(General model)

HGFEDCBA

B RS-232C terminal

This is a control expansion terminal for factory use only. Consult you dealer for details.

C ZONE 2/ZONE 3 OUTPUT jacks

See page 97 for details.

D MULTI CH INPUT jacks

See page 26 for connection information.

E PRE OUT jacks

See page 28 for connection information.

F REMOTE IN/OUT jacks

See page 97 for details.

G Speaker terminals

See page 15 for connection information.

H PRESENCE/ZONE 2(3) speaker terminals

See page 17 for connection information.

INTRODUCTION

AC IN

9 AC OUTLETS

Use to supply power to your other A/V components (see page 30).

0 AC IN

Use this inlet to plug in the supplied power cable (see page 30).

A HDMI IN/OUT connectors

See page 101 for connection information.

English

CONNECTIONS

Before connecting speakers

The speaker layout below shows the standard ITU-R* speaker setting. You can use it to enjoy CINEMA DSP, multi-channel audio sources and THX.

ITU-R is the radio communication sector of the ITU (International Telecommunication Union).

1.8 m

30˚

60˚

80˚

SBL

More than 30 cm

SBR

Front speakers (FR and FL)

The front speakers are used for the main source sound plus effect sounds. Place these speakers an equal distance from the ideal listening position. The distance of each speaker from each side of the video monitor should be the same.

Center speaker (C)

The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system. Align the front face of the center speaker with the front face of your video monitor. Place the speaker centrally between the front speakers and as close to the monitor as possible, such as directly over or under it.

1.8 m

Surround speakers (SR and SL)

The surround speakers are used for effect and surround sounds. Place these speakers behind your listening position, facing slightly inwards, about 1.8 m above the floor.

Surround back speakers (SBR and SBL)

The surround back speakers supplement the surround speakers and provide for more realistic front-to-back transitions. Place these speakers directly behind the listening position and at the same height as the surround speakers. They should be positioned at least 30 cm apart. Ideally, they should be positioned at the same width as the front speakers.

Subwoofer

The use of a subwoofer, such as the YAMAHA Active Servo Processing Subwoofer System, is effective not only for reinforcing bass frequencies from any or all channels, but also for high fidelity reproduction of the LFE (lowfrequency effect) channel included in Dolby Digital and DTS software. The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce wall reflections.

Presence speakers (PR and PL)

Presence speakers supplement the sound from the front speakers with extra ambient effects produced by CINEMA DSP (see page 57). These effects include sounds that filmmakers intend to locate a little farther back behind the screen in order to create more theater-like ambience. Place these speakers at the front of the room about 0.5 – 1 m outside the front speakers, facing slightly inwards, and about 1.8 m above the floor.

Note

Surround back and presence speakers do not output sound simultaneously. You can set to prioritize either set of speakers using the PRIORITY parameter in MANUAL SETUP (see page 72).

■ Di-pole speaker layout

Either di-pole or direct radiating speaker types can be used for THX surround. If you choose di-pole speakers, please place the surround and surround back speakers according to the speaker layout below.

: Di-pole speaker

: Direction of the di-pole speaker phase

SBL

SBR

CONNECTIONS

Connecting speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass.

CAUTION

• If you will use 6 ohm speakers, be sure to set this unit’s speaker impedance setting to 6 ohms before using (see page 31). If you will use 8 ohm speakers, use this unit’s initial setting for speaker impedance.

• Before connecting the speakers, make sure that this unit is disconnected from the power source.

• Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/or speakers.

• Use magnetically shielded speakers. If this type of speaker still creates interference with the monitor, place the speakers away from the monitor.

Note

A speaker cord is actually a pair of insulated cables running side by side. One cable is colored or shaped differently, perhaps with a stripe, groove or ridges. Connect the striped (grooved, etc.) cable to the “+” (red) terminals on this unit and your speaker. Connect the plain cable to the “–” (black) terminals.

PREPARATION

■ Connecting to the speaker terminals

FRONT terminals

Connect one or two speaker systems to these terminals. If you use only one speaker system, connect it to either of the FRONT A or B terminals.

Note

The Canada model cannot output to two pairs of speaker systems simultaneously.

CENTER terminals

Connect a center speaker to these terminals.

SURROUND ZONE 2(3) terminals

Connect surround speakers to these terminals.

SUBWOOFER jack

Connect a subwoofer with a built-in amplifier, such as the YAMAHA Active Servo Processing Subwoofer System, to this jack.

SURROUND BACK terminals

Connect surround back speakers to these terminals. If you only connect one surround back speaker, connect it to the left (L) terminals.

English

CONNECTIONS

1 Remove approximately 10 mm of insulation

from each of the speaker cables.

10 mm

2 Twist the exposed wires of the cable together

to prevent short circuits.

3 Loosen the knob using the supplied speaker

terminal wrench.

Speaker terminal wrench

5 Tighten the knob to secure the wire using the

supplied speaker terminal wrench.

Speaker terminal wrench

Red: positive (+)

Black: negative (–)

6 Hook the speaker terminal wrench onto

WRENCH HOLDER on the rear panel of this unit when not in use.

Red: positive (+)

Black: negative (–)

4 Insert one bare wire into the hole on the side

of each terminal.

Red: positive (+)

Black: negative (–)

CONNECTIONS

PRESENCE/ZONE 2(3) terminals

Connect presence speakers to these terminals.

Note

You can also use these terminals to connect the Zone 2 speakers (see page 98).

1 Open the tab.

2 Insert one bare wire into the hole of each

terminal.

3 Return the tab to secure the wire.

■ Speaker layout

Refer to the following illustration as to where to place each speaker in your listening room.

1 Subwoofer 2 Front right speaker 3 Front left speaker 4 Center speaker 5 Surround back right speaker 6 Surround back left speaker 7 Surround right speaker 8 Surround left speaker 9 Presence right speaker 10 Presence left speaker

PREPARATION

■ Connecting the banana plug

(With the exception of U.K., Europe and Asia models) First, tighten the knob and then insert the banana plug connector into the end of the corresponding terminal.

Banana plug

(With the exception of U.K., Europe and Asia models)

You can also use banana plugs with the PRESENCE/ZONE 2(3) speaker terminals. Open the tab, then insert one banana plug connector into the hole of each terminal. Do not attempt to close the tabs after connecting the banana plugs.

English

CONNECTIONS

(General model)

Subwoofer with

built-in amplifier

Front speakers (A)

LeftRight

Center

speaker

Front

speakers

(B)

FRONT

SURROUND

SUBWOOFER

SURROUND BACK/PRESENCE

LeftRight LeftRight

Surround speakers

SPEAKERS

–

FRONT

–

PRE OUT

CENTER

–

SINGLE

(SB)

SURROUND BACK

Surround back speakers

–

CENTER

–

++––

–

SINGLE

–

SPEAKER IMPEDANCE

–

PRESENCE/ZONE 2(3)

LeftRight

Presence speakers

• You can connect both surround back and presence speakers to this unit, but they do not output sound simultaneously. You can set to prioritize either set of speakers using the PRIORITY parameter in MANUAL SETUP (see page 72).

• The surround back speakers output the surround back channel included in Dolby Digital EX and DTS-ES software and operate only when the Dolby Digital EX, DTS-ES, Dolby Pro Logic x

, THX Select2, THX Music, THX Games or THX Surround EX

decoder is turned on.

• The presence speakers output ambient effects created by the DSP sound fields. They do not output sound when other sound fields are selected.

Using bi-wire and bi-AMP connections

Some of the speakers commercially available these days have speaker wire connections that allow bi-wiring or biamplification to enhance the performance of the speaker system. This unit allows you to make bi-wire and bi-AMP connections to one speaker system. Check if your speakers support bi-wiring or bi-amplification. As these speakers are shipped to you, you will note gold-plated shorting bars or bridges, one connecting the two red input terminals and the other connecting the two black input terminals. Remove these shorting bars or bridges only if you plan to bi-wire or bi-AMP your speakers.

FRONT

++–

–

This unit

CONNECTIONS

–

PREPARATION

■ Conventional connection

If you want to connect your speakers as traditional loudspeakers using the conventional connection method, connect your speakers using the regular left and right speaker wire connections and ignore the second set of terminals.

–

This unit

Shorting bars or bridges

Shorting bars

or bridges

FRONT

++–

■ Bi-wire connection

The bi-wire connection separates the woofer from the combined midrange and tweeter section. A bi-wire compatible speaker has four binding post terminals. These two sets of terminals allow the speaker to be split into two independent sections. This split connects the mid and high frequency drivers to one set of terminals and the low frequency driver to the other pair.

■ Bi-AMP connection

The bi-AMP connection uses two amplifiers for both speakers. One amplifier is connected to the woofer section of a loudspeaker while the other is connected to the combined mid and tweeter section. With this arrangement each amplifier operates over a restricted frequency range. This restricted range presents each amplifier with a much simpler job and each amplifier is less likely to influence the sound in some way. The internal crossover of the speaker consists of a LPF (low pass filter) and a HPF (high pass filter). As its name implies, the LPF passes frequencies below a cutoff and rejects frequencies above the cutoff frequency. Likewise, the HPF passes frequencies above its cutoff.

Notes

• Remove the shorting bars or bridges to separate the LPF (low pass filter) and HPF (high pass filter) crossovers.

• To activate the bi-AMP connections, set BI-AMP to ON in ADVANCED SETUP (see page 84).

• To make the bi-AMP connections, use the FRONT and SURROUND BACK terminals as shown below.

–

Notes

• Remove the shorting bars or bridges to separate the LPF (low pass filter) and HPF (high pass filter) crossovers.

• To use the bi-wire connections, press SPEAKERS A on the front panel so that SP A lights up in the front panel display.

FRONT

–

SURROUND BACK

This unit

–

SINGLE

English

CONNECTIONS

Information on cables and jacks used for connections

CAUTION

Do not connect this unit or other components to the main power until all connections between components are complete.

■ Cable indications

For analog signals

left analog cables

right analog cables

For digital signals

optical cables

coaxial cables

For video signals

video cables

S-video cables

■ Analog jacks

You can input analog signals from audio components by connecting audio pin cables to the analog jacks on this unit. Connect red plugs to the right jacks and white plugs to the left jacks.

■ Digital jacks

This unit has digital jacks for direct transmission of digital signals through either coaxial or fiber optic cables. You can use the digital jacks to input PCM, Dolby Digital and DTS bitstreams. When you connect components to both the COAXIAL and OPTICAL jacks, priority is given to signals input at the COAXIAL jack. All digital input jacks are compatible with 96-kHz sampling digital signals.

Note

This unit handles digital and analog signals independently. Thus audio signals input at the analog jacks are only output at the analog OUT (REC) jacks. Likewise, audio signals input at the digital (OPTICAL or COAXIAL) jacks are only output at the DIGITAL OUTPUT jacks.

For HDMI signals

CONNECTIONS

■ Audio jacks

This unit has four types of audio jacks (analog audio, digital audio coaxial, digital audio optical and HDMI). Connection depends on the availability of audio jacks on your other components.

AUDIO

DIGITAL AUDIO

AUDIO jacks

For conventional analog audio signals.

DIGITAL AUDIO (COAXIAL) jacks

For digital audio signals transmitted via digital coaxial cables.

■ Audio signal flow for OUT (REC)

Input

HDMI

DIGITAL AUDIO (COAXIAL)

DIGITAL AUDIO (OPTICAL)

(COAXIAL)

DIGITAL AUDIO

(OPTICAL)

HDMI

DIGITAL AUDIO (OPTICAL) jacks

For digital audio signals transmitted via digital optical cables.

HDMI jacks

For HDMI digital audio signals.

Output

OUT (REC)

Digital audio

PREPARATION

AUDIO

Through

Digital output

Analog output

Analog audio

Notes

• The audio signals input at the HDMI IN 1 or HDMI IN 2 jack are output at the DIGITAL OUTPUT jacks only and are not output at the analog OUT (REC) jacks.

• 2-channel as well as multi-channel PCM, Dolby Digital and DTS signals input at the HDMI IN 1 or HDMI IN 2 jack can be output at the HDMI OUT jack only when HDMI SET is set to OTHER (see page 75).

• 2-channel PCM, Dolby Digital and DTS signals except multi-channel PCM signals input at the HDMI IN 1 or HDMI IN 2 jack can be output at the DIGITAL AUDIO (OPTICAL) jacks.

• Copy-protected 2-channel PCM signals with over 48 kHz/16 bit input at the HDMI IN 1 or HDMI IN 2 jack are not output at the DIGITAL AUDIO (OPTICAL) jacks.

English

CONNECTIONS

■ Video jacks

This unit has four types of video jacks (composite, component, S-video and HDMI). Connection depends on the availability of input jacks on your monitor. When V CONV. is set to ON (see page 78), the analog video signals input at the VIDEO, S VIDEO and COMPONENT VIDEO jacks can be output at the VIDEO, S VIDEO and COMPONENT VIDEO jacks interchangeably. In addition, when V CONV. page 79), the analog video signals input at the VIDEO, S VIDEO and COMPONENT VIDEO jacks can be digitally upconverted and output at the HDMI OUT jack.

is set to ON (see page 78) and HDMI I/P is set to ON (see

VIDEO

S VIDEO

VIDEO jacks

For conventional composite video signals.

S VIDEO jacks

For S-video signals, separated into luminance (Y) and color (C) video signals to achieve high-quality color reproduction.

■ Video signal flow for MONITOR OUT

Input

HDMI

COMPONENT VIDEO

S VIDEO

COMPONENT VIDEO

Y PBP

HDMI

COMPONENT VIDEO jacks

For component signals, separated into luminance (Y) and color difference (P

B, PR) to provide the best quality in

picture reproduction.

HDMI jacks

For HDMI digital video signals.

Output

(MONITOR OUT)

Digital video

Analog video

VIDEO

Through

Component interlace/progressive conversion (see page 78)

HDMI interlace/progressive up-conversion (see page 79)

Notes

• The analog video signals output at the COMPONENT VIDEO jacks can be deinterlaced from 576i to 576p. Set CMPNT I/P to ON in MANUAL SETUP to activate this feature (see page 78).

• The analog video signals input at the COMPONENT VIDEO jacks and output at the S VIDEO or VIDEO jacks cannot be converted to 576p/1080i/720p.

• When the analog video signals are input at the COMPONENT VIDEO, S VIDEO and VIDEO jacks, the priority order of the input signals is as follows where the analog video signals input at the COMPONENT VIDEO jacks have the top priority.

1. COMPONENT VIDEO

2. S VIDEO

3. VIDEO

• Component interlace/progressive conversion (see page 78) and HDMI interlace/progressive up-conversion (see page 79) are available only when V CONV. is set to ON (see page 78).

CONNECTIONS

Connecting HDMI components

This unit has the HDMI IN 1 and HDMI IN 2 jacks for digital audio and video signal input as well as the HDMI OUT jack for digital audio and video signal output. Connect the HDMI IN 1 or HDMI IN 2 jack of this unit to the HDMI OUT jack of other HDMI components (such as a DVD player). Connect the HDMI OUT jack of this unit to the HDMI IN jack of other HDMI components (such as a TV and a projector). The video or audio signals input at the HDMI IN 1 or HDMI IN 2 jack you selected using the HDMI IN menu in I/O ASSIGNMENT (see page 76) or the INPUT selector on the front panel are output at the HDMI OUT jack of this unit. In addition, the audio signals input at the HDMI IN 1 or HDMI IN 2 jack are output to speakers, headphones and the DIGITAL OUTPUT jacks.

Notes

• We recommend using an HDMI cable shorter than 5 meters with the HDMI logo printed on it.

• Digital audio signals input at the HDMI IN jacks are not output at the analog AUDIO OUT jacks.

• Some audio signals may not be output at the DIGITAL OUTPUT jacks depending on the signal type.

• The analog video signals input at the composite video, S-video and component video jacks can be digitally up-converted to be output at the HDMI OUT jack. Set HDMI I/P to ON in MANUAL SETUP to activate this feature (see page 79).

• Some video monitors connected to this unit via a DVI connection fail to recognize the HDMI audio signals being input if they are in the standby mode. In this case, the HDMI indicator flashes irregularly and HDCP ERROR appears in the front panel display as if the DVI monitors do not support the HDCP copy protection standards.

IN 1

IN 2

OUT

HDMI

DVD Player

Cable TV or

Satellite tuner

Video

monitor

HDMI out

HDMI in

PREPARATION

(General model)

English

CONNECTIONS

Connecting video components

■ Connecting a DVD player

HDMI out

Audio out

Video out

S VIDEO

MONITOR OUT

VIDEO

DVD

OUTPUT

AUDI OVIDEO

Video

monitor

Video in

HDMI in

Optical out

Coaxial out

DVD

DIGITAL

OUTPUT

DIGITAL INPUT

DVD

OPTICAL

COAXIAL

IN 1

IN 2

OUT

HDMI

DVD player

COMPONENT VIDEO

DVD

PBY

MONITOR OUT

(General model)

Note

Check the availability of jacks on your DVD player and select one type of connection for audio/video input/output. However, in case you make an HDMI connection, you can make both audio and video connections using a single HDMI cable.

■ Connecting other video components

HDMI out

CONNECTIONS

Optical out

Cable TV or

Audio out

satellite tuner

Video out

(General model)

CBL/SAT

DIGITAL

OUTPUT

DIGITAL INPUT

OPTICAL

HDMI

COAXIAL

DVR/

VCR 2

IN 1

IN 2

OUT

DTV

CBL/

SAT

COMPONENT VIDEO

S VIDEO

PRPBY

VIDEO

CBL/

SAT

VCR 1

OUT

AUDIOVIDEO

PREPARATION

Video

monitor

LR LR

Audio in

Video out

DVD recorder

or VCR

Audio out

Coaxial out

HDMI in

HDMI out

Note

Check the availability of jacks on your other video components and select one type of connection for audio/video input/output. However, in case you make an HDMI connection, you can make both audio and video connections using a single HDMI cable.

English

CONNECTIONS

■ Connecting to the MULTI CH INPUT jacks

This unit is equipped with 6 additional input jacks (left and right FRONT, CENTER, left and right SURROUND and SUBWOOFER) for discrete multi-channel input from a multi-format player, external decoder, sound processor or pre-amplifier. If you set INPUT CH to 8ch in MULTI CH SET (see page 77), you can use the input jacks assigned as FRONT in MULTI CH SET (see page 77) together with the MULTI CH INPUT jacks to input 8-channel signals. Connect the output jacks on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to match the left and right outputs to the left and right input jacks for the front and surround channels.

For 6-channel input For 8-channel input

FRONT(6CH)/SB(8CH)

SURROUND

SUBWOOFER

MULTI CH INPUT

Subwoofer

out

Multi-format player/

External decoder

Front out

CENTER

Center out

Surround out

Surround back out

FRONT(6CH)/SB(8CH)

SURROUND

CENTER

SUBWOOFER

MULTI CH INPUT

Subwoofer out

Center out

Multi-format player/

External decoder

LRLR

Surround out

Front out

DVD

DTV

CBL/

SAT

VCR 1

OUT

DVR/VCR 2

AUDIO

(

PLAY

MD/TAPE

OUT

(REC)

(

PLAY

CD-R

OUT

(REC)

AUDIO

)

Notes

• When you select MULTI CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you cannot select sound field programs.

• This unit does not redirect signals input at the MULTI CH INPUT jacks to accommodate for missing speakers. We recommend that you connect at least a 5.1-channel speaker system before using this feature.

• When headphones are used, only front L/R channels are output.

■ Connecting to the VIDEO AUX jacks on the front panel

Use these jacks to connect any video source, such as a game console or video camera, to this unit.

S VIDEO VIDEO L

VIDEO/AUX

AUDIO R OPTICAL

Optical out

Audio out R Audio out L

Video out S-video out

Game console or video camera

Connecting audio components

Optical in

CD recorder

CONNECTIONS

Optical in

MD recorder or

tape deck

DIGITAL INPUT

MD/TAPE

CD-R

DIGITAL OUTPUT

Audio in

OPTICAL

COAXIAL

Audio out

(General model)

LRLRLR LR

AUDIO

(PLAY)

MD/TAPE

OUT

(REC) (PLAY)

CD-R

OUT

(REC)

PHONO

Audio inAudio out

PREPARATION

GND

LRLR

Audio out

Optical out

Coaxial out

Audio out

CD player

GND

Turntable

Notes

• Check the availability of jacks on your audio components and select one type of connection for audio/video input/output.

• PHONO jacks are for connecting a turntable with an MM or high-output MC cartridge. If you have a turntable with a low-output MC cartridge, use an in-line boosting transformer or MC-head amplifier when connecting to these jacks.

• Connect your turntable to the GND terminal to reduce noise in the signal. However you may hear less noise without the connection to the GND terminal for some record players.

English

CONNECTIONS

■ Connecting an external amplifier

If you want to increase the power output to the speakers, or want to use another amplifier, connect an external amplifier to the PRE OUT jacks as follows.

Notes

• When audio pin plugs are connected to the PRE OUT jacks for output to an external amplifier, it is not necessary to use the corresponding SPEAKERS terminals. Set the volume of the external amplifier connected to this unit to the maximum.

• The signal output at the FRONT PRE OUT and CENTER PRE OUT jacks are affected by the TONE CONTROL settings.

• If SPEAKERS A is turned off and SPEAKERS B is set to ZONE B (see page 80), signals will only be output at the FRONT PRE OUT jacks.

PRE OUT

FRONT

SURROUND

SUBWOOFER

SURROUND BACK/PRESENCE

CENTER

SINGLE

(SB)

1 FRONT PRE OUT jacks

Front channel line output jacks.

2 SURROUND PRE OUT jacks

Surround channel line output jacks.

3 SUBWOOFER PRE OUT jack

Connect a subwoofer with built-in amplifier, such as the YAMAHA Active Servo Processing Subwoofer System, to this jack.

4 SURROUND BACK/PRESENCE PRE OUT

jacks

Surround back or presence channel line output jacks. If you only connect one external amplifier for the surround back channel, connect it to the left (L) jack.

5 CENTER PRE OUT jack

Center channel line output jack.

Notes

• Each PRE OUT jack outputs the same channel signal as the corresponding speaker terminals. However, when both surround back and presence speakers are setup in this unit, the signals output at SURROUND BACK/PRESENCE PRE OUT jacks may not correspond to the correct speakers.

• Adjust the volume level of the subwoofer with the control on the subwoofer.

• Some signals may not be output at the SUBWOOFER PRE OUT jack depending on the SPEAKER SET settings (see page 71).

+ 93 hidden pages