Yamaha PSR-S910, PSR-S710 User Manual
DIGITAL WORKSTATION
/
Version 1.10 Upgrade Manual
Version 1.10 of the firmware adds the following functionality to PSR-S910 and PSR-S710 models.
• Support for the Wi-Fi Protected Access (WPA) wireless encryption standard (with the exception of certain
USB-LAN adaptors
•
Support for the Wi-Fi Protected Setup (WPS)*2 standard, which makes it easier to setup wireless home
networks
• Support for the following USB-LAN adaptors.
Wireless: Buffalo WLI-UC-GN Buffalo WLI-UC-GNHP Planex GW-USMicroN Planex GW-USMini2N
Wired: LINKSYS USB300M AIRLINK101 ASOHOUSB 10/100Mbps Fast Ethernet USB 2.0 Adapter
*1: For more details, please visit the Yamaha Piano / Keyboard website (below) and refer to the list of USB devices confirmed as
*2: For more details, please refer to the Internet Connection Guide, which can be downloaded from the Yamaha Manual Library
(with the exception of certain USB-LAN adaptors*1)
Edimax EW-7711UAn Edimax EW-7711UTn Hawking HWUN3 Tenda W311U
Belkin F6D4050 LogiLink WL0049A LogiLink WL0054
macally AIR2NET INTELLINET Hi-Speed USB 2.0 to Fast Ethernet Adapter
working with our products. http://music.yamaha.com/download
website. http://www.yamaha.co.jp/manual/english/
*1
)
Confirming the Current Version
1. Turn on the PSR-S910/S710.
This can be done by pressing the [STANDBY/ON] switch
located at the left of the front panel.
2. Confirm the instrument’s current firmware
version as follows.
2-1 Press the [FUNCTION] button.
2-5 Press the [8▲] (EXIT) button or the [EXIT] button to close
the window.
3. Turn off the PSR-S910/S710.
This can be done by pressing the [STANDBY/ON] switch
located at the left of the front panel.
Upgrading the Firmware
To upgrade the firmware, place the upgrade data on a USB flash
memory device and then carry out the upgrading procedure as
described below.
1. Plug the USB flash memory device containing
the upgrade data into the PSR-S910/S710.
2. Hold down the [START/STOP] button and press
the [STANDBY/ON] switch.
2-2 Press the [J] (UTILITY) button.
2-3 Using the TAB [E] / [F] buttons, select the OWNER tab
and display the Owner setting screen.
2-4 Press the [7▲] (VERSION) button to display the current
firmware version. If the displayed version number is less
than 1.10, the firmware should be upgraded.
Continue to hold down the [START/STOP] button until the
following message is displayed.
3. Install the upgrade data.
To do so, release the [START/STOP] button and then press
it once again.
1
After indicating that data is being loaded, the PSR-S910/S710
will begin to install the new version of the firmware.
The following message is displayed at this time. Upgrading of
the firmware takes approximately 5 minutes.
1. Plug the USB flash memory device containing
the upgrade data into the PSR-S910/S710.
2. Hold down the [START/STOP] button and press
the [STANDBY/ON] switch.
The USB flash memory device must not be unplugged and the
instrument must not be turned off while the firmware is being
installed. Failure to observe this precaution may render the
PSR-S910/S710 unfit for use.
The following message is displayed upon completion of the
firmware installation process.
4. Turn off the PSR-S910/S710 and unplug the USB
flash memory device.
Reconfirming the Current Version
After any firmware upgrade, it is recommended that you confirm
the current version once again as described below.
1. Turn on the PSR-S910/S710.
This can be done by pressing the [STANDBY/ON] switch
located at the left of the front panel.
Continue to hold down the [START/STOP] button until the
following message is displayed.
The USB flash memory device must not be unplugged and the
instrument must not be turned off at this time. Failure to observe
this precaution may render the PSR-S910/S710 unfit for use.
3. Press the [BREAK] button to delete the upgrade
data.
The following confirmation message will be displayed.
2. Confirm the instrument’s current firmware
version as follows.
2-1 Press the [FUNCTION] button.
2-2 Press the [J] (UTILITY) button.
2-3 Using the TAB [E] / [F] buttons, select the OWNER tab
and display the Owner setting screen.
2-4 Press the [7▲] (VERSION) button to display the current
firmware version.
If the upgrade process has been completed successfully,
version 1.10 will be shown in the window displayed. If the
version has not changed, it is likely that the installation
procedure was not completed successfully. In such a
case, repeat the procedure carefully as described herein.
3. Press the [8▲] (EXIT) button or the [EXIT] button
to close the window.
Deleting Upgrade Data
Deletion using the instrument:
Version 1.10 of the firmware for PSR-S910 and PSR-S710
models makes it possible to delete upgrade data from a USB
flash memory device using the instrument itself. To do so,
proceed as follows.
4. To delete the upgrade data, release the [START/
STOP] button and then press it once again.
The PSR-S910/S710 will begin deleting the upgrade data.
The following message is displayed at this time.
The USB flash memory device must not be unplugged and the
instrument must not be turned off while the upgrade data is
being deleted. Failure to observe this precaution may result in
the USB flash memory device being permanently damaged.
The following message is displayed upon completion of the
data deletion process.
5. Turn off the PSR-S910/S710 and unplug the USB
flash memory device.
This can be done by pressing the [STANDBY/ON] switch
located at the left of the front panel.
2
Loading...