Copy Regulations - Other Countries.............................................................................4-3
Xerox®Versant®3100 PressXerox®Versant®180 Pressii
Safety Guide
1
Notices and Certifications
Warning Markings
Warning
This symbol alerts users to areas of the product where there is the possibility of personal
injury.
Hot Warning
This symbol alerts users to areas of the product where there are heated surfaces, which
should not be touched.
Caution
This symbol alerts users to areas of the equipment, which require special attention to
avoid the possibility of personal injury or damage to the equipment.
Laser Warning
This symbol indicates a Laser is being used in the equipment and alerts the user to refer
to the appropriate safety information.
Radio Frequency Emissions
FCC in the USA
This equipment has been tested and foundtocomply with the limits for a Class A digital
device, pursuant to Part 15 of the Federal Communications Commission (FCC) Rules.
These limits are designed to provide reasonable protection against harmfulinterference
when the equipmentisoperated in a commercial environment.Thisequipmentgenerates,
uses, and can radiateradiofrequency energy and, if not installedandused in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his/her own expense.
Changes or modifications to this equipment not specifically approved by the Xerox
Corporation may void the user’s authority to operate this equipment.
Warning
Shielded cables must be used with this equipment to maintain compliance with FCC
regulations.
In Canada (ICES-003)
This Class “A” digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe “A” est conforme à la norme NMB-003 du Canada.
Safety Extra Low Voltage Approval
This Xerox product is in compliance with various governmental agencies and national
safety regulations. All system ports meet the Safety Extra Low Voltage (SELV) circuits
for connection to customer-owned devices and networks. Additions of customer-owned
or third-party accessories that are attached to the machine must meet or exceed the
requirements previously listed. All modules that require external connection must be
installed per the installation procedure.
Product Safety Certification
This product is certified by the followingAgencyusingtheSafety standardslistedbelow.
StandardAgency
CSA International
NEMKO
UL 60950-1:2007 (2nd edition) +R12.11
CAN/CSA-C22.2 No.60950-1-07(2ndedition) +A1:2011
The CE marking that is applied to this product symbolize the Xerox declaration of
conformity with the following applicable Directives of the European Union as of the
dates indicated:
Low Voltage Directive 2014/35/EU
Approximation of the laws of the member states related to low voltage equipment.
Approximation of thelaws of the member states related toelectromagneticcompatibility.
Radio Equipment Directive 2014/53/EU
Restrictionof the use of hazardous substances in electrical and electronic equipment.
Directive 2011/65/EU
A full declarationof conformity, defining the relevantdirectives and referencedstandards,
can be obtained from your Authorized local dealer.
CE Warnings
Warning
• Changes or modifications to this equipment not specifically approved by the Xerox
Corporation may void the user’s authority to operate this equipment.
• In order to allow this equipment to operate in proximity to Industrial, Scientific, and
Medical (ISM) equipment, the external radiation from the ISM equipment may have
limited or special mitigation measures taken.
• This is a Class A product in a domestic environment. This product may cause radio
frequency interference in which case the user may be required to take adequate
measures.
• Shielded cables must be used with this equipment to maintain compliance with
Council Directive 2004/108/EC and 2014/53/EU.
Compliance with the EU
Compliance with EU Harmonics Standard EN 61000-3-12:2005
“Equipment complying with EN 61000-3-12:2005”
This equipment complies with EN61000-3-12:2005 which defines limits for harmonic
currents which may be produced by equipment installed in the European Union and the
European Economic Area.
Complianceisbasedonapplicationof limits which justify installation and unconditional
connection to the public low voltage supply.
Compliance with EU Flicker Standard EN 61000-3-11:2000
“Equipment complying with EN 61000-3-11:2000”
This equipment is suitable for use only in premises having a service current capacity
equal to or greater than 100 Amps per phase.