003_03
Instructions for installation,
use and maintenance
07/2007
ELECTRIC BAIN-MARIE
AGB 591/WP
AGB 531/WP
AGB 532/WP
003-03 - Electric bain-marie
Models and dimensions page 3
Technical data 6
Installation instructions 7
Installation 7
Legal and technical requisites 7
Installation 7
Wiring 7
Unipotential 7
Ignition 7
Emptying the bath 8
Cleaning and taking care
of the appliance
8
What to do if not using the appliance for
a long time 8
What to do if something goes wrong 8
Maintenance 8
WEEE Directive 8
Wiring diagrams 9
Warning 10
2
INDEX
003-03 - Electric bain-marie
3
1 - DIAGRAM
AGB 591/WP
Weight approx.19 kg
A
D
B
C
E
A
Temperature control
B
Water drain
release
C
Switch
D
Resistance pilots
E
Water drain
A
D
B
C
A
B
C
D
E
E
003-03 - Electric bain-marie
4
1 - DIAGRAM
AGB 531/WP
Weight approx.19 kg
A
D
B
C
E
A
Temperature control
B
Water drain
release
C
Switch
D
Resistance pilots
E
Water drain
AGB 532/WP
Weight approx.32 kg
A
D
B
C
A
C
B
D
E
E
003-03 - Electric bain-marie
5
1 - DIAGRAM
A
D
B
C
E
A
Temperature control
B
Water drain
release
C
Switch
D
Resistance pilots
E
Water drain
A
D
B
C
A
C
B
D
E
E
003-03 - Electric bain-marie
6
2 - CHARACTERISTICS OF THE APPLIANCES
The data plate is located on the rigth hand side of the
control panel and contains all the data needed for connecting
it up to the mains electricity supply.
CAT/KAT GAS/GAZ G30 G31 G20 G25
II2H3B/P P mbar 30 30 20 -
II2H3+ P mbar 30 37 20--
II2H3+ P mbar 28 37 20 -
TIPO/TYPE
MOD.
ART.
N.
N.
Qn kW
MOD.
V AC kW Hz
THE APPLIANCE MUST BE CONNECTED IN COMPLIANCE WITH THE LAWS IN FORCE
AND INSTALLED IN A WELL-VENTILATED ROOM. READ THE INSTRUCTION MANUALS
BEFORE INSTALLING AND USING THE APPLIANCE.
THE APPLIANCE MUST BE INSTALLED BY QUALIFIED PERSONNEL.
m3/h
II2ELL3B/P P mbar 50 50 20 20
II2E+3+ P mbar 28 37 20 25
II2H3B/P P mbar 50 50 20 -
I2E P mbar - - 20 -
--II2H3B/P P mbar 30 30
II2H3+ P mbar 28 37 20 -
I3B/P P mbar 30 30
I3+ P mbar 28 37
Predisposto a gas: - Gas preset: - Prevu pour gaz:
Eingestelt für Gas: - Preparado para gas: -
--
--
Geschuckt voor:
SE FI DK CZ SK SI
IT CH PT
ES IE GB GR
NL
25II2L3B/P P mbar 30 30
DE
FR BE
AT CH
LU
EE LV LT
EE LV LT
NO MT CY IS HU
CY
MADE IN ITALY
Model
AGB 591/EP
AGB 531/WP
AGB 532/WP
Dim.: LxWxH
400 x 615 x 300
400 x 700 x 300
400 x 700 x 875
800 x 615 x 300
800 x 700 x 300
800 x 700 x 875
3 - TECHNICAL DATA
Voltage rating
230 V
230 V
230 V
230 V
230 V
230 V
Power
1.0 kW
1.0 kW
1.0 kW
2.0 kW
2.0 kW
2.0 kW
Lead wire / Section
3 x 1.5 mm
3 x 1.5 mm
3 x 1.5 mm
3 x 2.5 mm
3 x 2.5 mm
3 x 2.5 mm
2
2
2
2
2
2
Before beginning installation, remove all packaging from
the appliance. Some parts are protected with an adhesive
film which should be carefully removed.
Any remnants of glue should be thoroughly cleaned using
suitable substances such as benzine. Under no circumstances should abrasive substances be used.
Fit the legs to the appliance; the appliance must be levelled using a spirit level. Slight irregularities can be levelled
by adjusting the feet themselves.
With table models, make sure that the base chosen is capable of supporting the weight of the appliance. The main
switch or plug should be located in the vicinity of the appliance and easy of access. We recommend installing the
machine under a range hood so that all the fumes are removed as quickly as possible. If the appliance is to be installed near walls, dividing walls, kitchen equipment or decorative pannelling, these should be in non-inflammable
material or covered with non-inflammable material.
Make sure that all fire prevention standards and safety precautions are strictly adhered to.
Warning!
With Top models, carefully measure the distance
between the appliance and the edge of the base (Fig. 2).
Legal and technical requisites
When installing the appliance, the following safety standards must be adhered to:
- Local accident prevention standards
- Current CEI standards.
Installation
Installation, start-up and maintenance should only be carried out by expert personnel. All work required to install
the appliance should be carried out in compliance with all
local standards and regulations. The manufacturers decline all responsibility where poor performance is due to incorrect installation in disregard of the above conditions.
Warning!
In compliance with international regulations, when
connecting the appliance to the mains power supply, a
device with a minimum aperture of 3 mm between contacts must be fitted upstream of the appliance, allowing omnipolar disconnection of the appliance from
the mains.
Wiring
When choosing the lead wire, make sure it has the following characteristics: it should be at least of the H07 RNF type and its section should be large enough for the appliance (see "Technical specifications and dimensions",
page 6).
Wire entry on top models is on the back wall, and underneath all other models. In both cases the terminal board is
at the front, behind the control panel.
Pass the wire through the core hitch and wire clamp, plug
the leads into their terminals on the board and secure
them.
The earth lead must be a little longerthan the others so
that it is the last lead to disconnect if the wire clamp
breaks.
Unipotential
The appliance must be connected up to a unipotential system. The connection screw is located on all top models
at the back on the right hand side, while in other models it
is located underneath the appliance on the right hand side. It is labelled.
Warning!
The manufacturers cannot be held responsible for any
damage due to inadequate or incorrect installation.
Under such circumstances the guarantee will be considered null and void.
Warning!
- Beware of inexpert handling!
- Never leave the appliance on without water!
Ignition
Check that the water drain release is closed. Fill the bath
with water up to the level marked. Turn on the main switch
upstream of the appliance.
On the twin-bath models (AGB 532/WP) both baths can
be used independently of each other at different temperatures, or one can be used without the other. Turn the main
switch on the appliance. It will light up indicating that the
appliance is on.
Switch on switch C (pages 4 ...5) and use knob A to position the thermostat on the desidered temperature,
between 30°C and 90°C inclusive; the pilot light will come
on; this means that the resistances are on. As soon as the
required temperature is reached, the pilot light will go off.
To turn the appliance off, simply turn the knob back to '0'
and switch off.
INSTALLATION INSTRUCTIONS
003-03 - Electric bain-marie
7
Emptying the bath
First of all a suitable bowl for emptying the water into
should be found. Fit the drainage pipe as shown in the
picture (2). Open the oil drain tap.
Important
With Top models, make sure you respect the distance
between the appliance and the edge of the base.
CLEANING AND TAKING CARE OF THE
MACHINE
Warning!
Never clean the appliance with jets of water, whether
direct or pressurised.
Allow the machine to cool down before cleaning
Before starting to clean the appliance, disconnect from
the mains.
All steel parts should be washed in warm water, using a
neutral detergent, then rinsed thoroughly to eliminate any
residual detergent.
Dry using a dry cloth. Avoid using abrasive or corrosive
detergents which could damage the steel.
What to do if not using the appliance
for a long time
Thoroughly clean and dry the machine as described.
Disconnect the power supply.
What to do if something goes wrong
If anything goes wrong, immediately turn the appliance
off, then turn off the power supply at the switch located
upstream of the appliance, and call the aftersales department.
MAINTENANCE
All maintenance should be carried out by qualified personnel only. Before carrying out any maintenance work,
unplug the appliance or turn off the switch upstream of the
appliance.
USING THE APPLIANCE
003-03 - Electric bain-marie
8
2
THE 2002/96/EC DIRECTIVE (WEEE):
information to users
This informational note is meant only for owners
of equipment marked with the symbol shown in
Fig. A on the adhesive label featuring the technical specifications applied on the actual pro-
duct (the label also giving the serial number).
This symbol indicates that the product is classified, according to the regulations in force, as an item of electrical
and electronic equipment and conforms to EU Directive
2002/96/EC (WEEE) meaning that, at the end of its service
life, it must be treated separately from domestic waste,
i.e. it must be handed in free of charge to a separate waste electrical and electronic equipment collection centre
or returned to the reseller when buying a new equivalent
item of equipment.
The user is responsible for delivering the unit at the end of
its life to the appropriate collection facilities. Failure to do
so shall result in the user being subject to the penalties
prescribed by the legislation in force on waste.
Suitable separated collection so that the unit no longer
used can be sent off for environmentally compatible recycling, treatment and disposal helps avoid possible negative effects on the environment and on health and facilitates the recycling of the product's component materials.
For more detailed information on available collection systems, contact the local waste disposal service or the
shop you purchased the unit from.
Producers and importers fulfil their responsibility for environmentally compatible recycling, treatment and disposal
both directly and by joining a collective scheme.
MAX 120 mm
003-03 - Electric bain-marie
9
ELECTRICAL DIAGRAMS
H1
H1
T2
F1
B1
mA
L1 N PE
T2
R1
AGB 591/WP
AGB 531/WP
230 V
123
T2
H1
Terminal board
mA
Main switch (green light)
B1
Thermostat
F1
Pilot lamp
H1
Resistances
R1
F1
B1
mA
L1 N PE
R1
123
R1
F1
B1
AGB 532/WP
230 V
003-03 - Electric bain-marie
10
WARNING
DUE TO ITS POLICY OF CONTINUAL PRODUCT IMPROVEMENT, THE MANUFACTURER RESERVES THE RIGHT
TO MAKE ANY CHANGES DEEMED NECESSARY.
THE MANUFACTURER CANNOT BE HELD RESPONSIBLE IF THE INSTRUCTIONS CONTAINED IN THIS MANUAL ARE NOT OBSERVED.
THIS DOCUMENTATION IS ONLY INTENDED FOR
QUALIFIED TECHNICIANS WHO ARE AWARE OF THE
RESPECTIVE SAFETY REGULATIONS.
WHIRLPOOL EUROPE srl
V.le Guido Borghi, 27
I – 21025 Comerio – VA
Loading...