Whirlpool ADG 7561 Quick Reference Guide

Quick reference guide

Chart

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ

THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING

ANY BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES

AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

PROGRAM SELECTION		START/RESUME BUTTON
BUTTON		Push this button to start the selected program: the
Push “Programs” button		indicator lights up and goes off at the end of the
(repeatedly) until the indicator		program. When the door is opened during a
of the required program lights		washing cycle, the cycle is temporarily paused: the
up (see “Table of programs”		Start indicator blinks.
below).		To resume the cycle push the Start button and
		close the door within 3 seconds.

CANCEL/OFF BUTTON

Push this button to switch off the control panel. If pressed when a program is running it cancels the program ongoing draining water for 1 minute.

If pressed when the dishwasher is switched off it drains any possible liquids from dishwasher

(1 minute process).

If the indicator flashes repeatedly, see page 6 - chapter ”What to do if ...”.

Table of programs

Deter-

Consumption

P

Programs

Loading instructions

gent

Litres

kWh

Minutes 1)

1

Pre-Wash

cold

Crockery to be washed later.

—

5.0

0.02

10

2

Glasses

40°C

Light soiling, for example glasses

X

13.0

0.90

97

and cups.

3

Quickwash

40°C

Lightly soiled crockery, with no

X

13.0

0.70

30

dried-on food.

4

Eco 2)

50°C

Normally soiled crockery.

X

15.0

1.05

165

Energy-saving program.

5

Intensive

70°C

Recommended program for

heavily soiled crockery, especially

X

15.0

1.50

140

suitable for pans and saucepans.

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions

(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible

with sensor programs as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for

ADG 7561

detailed information on the EN/Standard loading comparison test and other tests, contact the following address:

“[e-mail]”.

5019 396 01965

GB -1-

How to set water hardness in order to always assure the best cleaning results

First time use

1- salt reservoir

2- rinse aid dispenser

3- detergent dispenser

4- racks system

5,6,7,8- available functions on the panel

9- filters

10spray arms

Water hardness should be set only before the first wash or if water hardness has been changed

Water hardness level is factory set for medium-hard water (level 4).

Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.

-Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds.

-Programs LEDs will indicate the water hardness setting.

-Press the Programs button to increase setting (when the level reaches 7, the next key press will set the level back to 1.

-Wait 30 seconds (control panel switches off) or press START/Resume button to save setting.

1. Ask your water supply company what the water hardness is...							2. ...enter this value on			Suggestions for detergent use
							your dishwasher
							3 first PROGRAM LEDs			Gel or Powder
German		French		English	Water hardness		lit on the panel
										(rinse aid and	Tablets
degrees °dH		degrees °fH		degrees °eH	level		(see table of programs)
										salt)
							P1	P2	P3
0	- 5	0	- 9	0 - 6.3	Soft	1
6 - 10		10	- 18	7 - 12.6	Medium	2
11	- 15	19	- 27	13.3 - 18.9	Average	3				go to step 1
16	- 21	28	- 37	19.6 - 25.9	Medium-hard	4				(see “Daily	if water is
										check”)	HARD extra salt
22	- 28	38	- 50	26.6 - 35	Hard	5
											needs to be
29	- 35	51	- 63	35.7 - 44.1	Very hard	6					added
											(go to step 1,
36	- 50	64	- 90	44.8 - 62.4	Extremely hard	7
											“Daily check”)

At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).

Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)		Daily check
1	Visual indicator	Screw on the cap.
	(depending	Salt residual
	on the model).	around the cap
	Unscrew cap.	need to be
		removed. Some
		salt reservoir have
		a level indicator
		integrated in the
		cap (see below
		how to check).

		Fill the salt reservoir with water		Add salt (never add detergent!)
			before the first wash only.	min. 0.8 kg / max. 1 kg
			(depending on the model)
	The salt level indicator lamp may remain lit Salt indicator on the control panel				Salt indicator on the salt reservoir cap
	at the end of several wash cycles. If the		The indicator lamp lights up when SALT			clear: NEEDS TO
	water hardness level falls within category				green: OK.
			NEEDS TO BE ADDED.			BE ADDED
	(soft), no salt is required.

GB -2-

Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator

Daily check

2	Visual
	indicator

If required, open the cover B (press the dedicated button).

Add rinse aid to the max. line ~150 ml

The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4).

Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.

Check the rinse aid indicator to check the level into the dispenser.

(depending on the model)

Rinse aid indicator on the control panel

The indicator lamp lights up when RINSE AID NEEDS TO BE ADDED.

Rinse aid indicator on the dispenser

dark: OK.

clear: NEEDS TO BE ADDED

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.

Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations

Daily use

Open the cover A	Insert detergent: Tablet / powder / liquid into the big chamber		Shut the cover
(press the dedicated button).			by pressing dedicated ribs.
3	Only fill the	Use only one tablet per one cycle, only
	detergent dispenser	placed in detergent dispenser.
	prior to starting a
	wash program.	All types of tablets can be used, but for
		2 in 1 type adding of salt is mandatory.

GB -3-